KAA-3528RGBS-11

3.5x2.8mm SURFACE MOUNT LED LAMP ATTENTION Part Number: KAA-3528RGBS-11 OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Hyper Red Green Blue Features Description z Suitable for all SMT assembly and solder process. The Hyper Red source color devices are made with AlGaInP z Available on tape and reel. on GaAs substrate Light Emitting Diode. z Package: 2000pcs / reel. The Green source color devices are made with InGaN z Moisture sensitivity level : level 3. on Sapphire Light Emitting Diode. z RoHS compliant. The Blue source color devices are made with InGaN Light Emitting Diode. Static electricity and surge damage the LEDS. It is recommended to use a wrist band or anti-electrostatic t h glove when handling the LEDs. All devices, equipment and machinery must be electrically grounded. Package Dimensions K g in g i r b Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAM4753 APPROVED: WYNEC REV NO: V.2B CHECKED: Allen Liu DATE: MAR/07/2013 PAGE: 1 OF 8 DRAWN: Y.Liu ERP: 1201008340 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly Orangeuces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. t h g i r b 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. g in K 4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. 4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. 5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. Detailed application notes are listed on our website. http://www.kingbright.com/application_notes SPEC NO: DSAM4753 APPROVED: WYNEC REV NO: V.2B CHECKED: Allen Liu DATE: MAR/07/2013 PAGE: 2 OF 8 DRAWN: Y.Liu ERP: 1201008340 Selection Guide Part No. Dice Min. Typ. 120 220 400 500 55 100 Hyper Red (AlGaInP) KAA-3528RGBS-11 Water Clear Green (InGaN) Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Blue (InGaN) 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Red Green Blue 630 515 468 λD [1] Dominant Wavelength Hyper Red Green Blue 621 525 470 Δλ1/2 Spectral Line Half-width Hyper Red Green Blue C Capacitance VF [2] Forward Voltage IR Reverse Current n i K b g Hyper Red Green Blue Max. t h IF=20mA nm IF=20mA nm IF=20mA pF VF=0V;f=1MHz 2.5 4.1 4 V IF=20mA 10 50 50 uA VR=5V 25 45 100 Hyper Red Green Blue 2 3.3 3.3 Hyper Red Green Blue Test Conditions nm g i r 20 30 25 Units Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Green Blue Units Power dissipation 75 123 120 mW DC Forward Current 30 30 30 mA Peak Forward Current [1] 195 150 150 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAM4753 APPROVED: WYNEC REV NO: V.2B CHECKED: Allen Liu DATE: MAR/07/2013 PAGE: 3 OF 8 DRAWN: Y.Liu ERP: 1201008340 KAA-3528RGBS-11 Hyper Red SPEC NO: DSAM4753 APPROVED: WYNEC t h g i r b g n i K REV NO: V.2B CHECKED: Allen Liu DATE: MAR/07/2013 PAGE: 4 OF 8 DRAWN: Y.Liu ERP: 1201008340 Green K SPEC NO: DSAM4753 APPROVED: WYNEC g in REV NO: V.2B CHECKED: Allen Liu g i r b t h DATE: MAR/07/2013 PAGE: 5 OF 8 DRAWN: Y.Liu ERP: 1201008340 Blue K SPEC NO: DSAM4753 APPROVED: WYNEC g in REV NO: V.2B CHECKED: Allen Liu g i r b t h DATE: MAR/07/2013 PAGE: 6 OF 8 DRAWN: Y.Liu ERP: 1201008340 KAA-3528RGBS-11 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. t h g i r b Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension g in Tape Dimensions (Units : mm) SPEC NO: DSAM4753 APPROVED: WYNEC K REV NO: V.2B CHECKED: Allen Liu DATE: MAR/07/2013 PAGE: 7 OF 8 DRAWN: Y.Liu ERP: 1201008340 PACKING & LABEL SPECIFICATIONS KAA-3528RGBS-11 t h g i r b g in K SPEC NO: DSAM4753 APPROVED: WYNEC REV NO: V.2B CHECKED: Allen Liu DATE: MAR/07/2013 PAGE: 8 OF 8 DRAWN: Y.Liu ERP: 1201008340