KPBD-3224SURKCGKC

3.2x2.4mm SMD CHIP LED LAMP Part Number: KPBD-3224SURKCGKC Hyper Red Green Features Descriptions 3.2x2.4mm SMD LED, 2.4mm thickness. The Hyper Red source color devices are made with Low power consumption. AlGaInP on GaAs substrate Light Emitting Diode. Ideal for backlight and indicator. The Green source color devices are made with AlGaInP Package : 1500pcs / reel. on GaAs substrate Light Emitting Diode. Moisture sensitivity level : level 3. RoHS compliant. t h ig r b Package Dimensions g in K Red Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD3553 REV NO: V.17A DATE: MAR/05/2016 APPROVED: Wynec CHECKED: Allen Liu DRAWN: J.L.Liang PAGE: 1 OF 6 ERP: 1203000875 Selection Guide Part No. Emitting Color (Material) Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. Typ. 700 1300 *120 *400 80 280 *80 2θ1/2 *280 Hyper Red (AlGaInP) KPBD-3224SURKCGKC Water Clear Green (AlGaInP) 20° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Hyper Red Green 645 574 λD [1] Dominant Wavelength Hyper Red Green 630 570 Δλ1/2 Spectral Line Half-width Hyper Red Green 28 20 C Capacitance Hyper Red Green 35 15 VF [2] Forward Voltage Hyper Red Green 1.95 2.1 IR Reverse Current t h Max. Units Test Conditions nm IF=20mA nm IF=20mA nm IF=20mA pF VF=0V;f=1MHz 2.5 2.5 V IF=20mA 10 10 uA VR = 5V ig r b g in K Hyper Red Green Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Green Units Power dissipation 75 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 185 150 mA Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature V -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAD3553 REV NO: V.17A DATE: MAR/05/2016 APPROVED: Wynec CHECKED: Allen Liu DRAWN: J.L.Liang PAGE: 2 OF 6 ERP: 1203000875 KPBD-3224SURKCGKC Hyper Red t h ig r b g in K SPEC NO: DSAD3553 REV NO: V.17A DATE: MAR/05/2016 APPROVED: Wynec CHECKED: Allen Liu DRAWN: J.L.Liang PAGE: 3 OF 6 ERP: 1203000875 Green K g in ig r b t h SPEC NO: DSAD3553 REV NO: V.17A DATE: MAR/05/2016 APPROVED: Wynec CHECKED: Allen Liu DRAWN: J.L.Liang PAGE: 4 OF 6 ERP: 1203000875 KPBD-3224SURKCGKC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) K g in ig r b t h Reel Dimension SPEC NO: DSAD3553 REV NO: V.17A DATE: MAR/05/2016 APPROVED: Wynec CHECKED: Allen Liu DRAWN: J.L.Liang PAGE: 5 OF 6 ERP: 1203000875 PACKING & LABEL SPECIFICATIONS KPBD-3224SURKCGKC t h ig r b g in K Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes SPEC NO: DSAD3553 REV NO: V.17A DATE: MAR/05/2016 APPROVED: Wynec CHECKED: Allen Liu DRAWN: J.L.Liang PAGE: 6 OF 6 ERP: 1203000875