KPT-1608SURCK

1.6X0.8mm SMD CHIP LED LAMP Part Number: KPT-1608SURCK Features Hyper Red Description 1.6mmX0.8mm SMD LED, 0.75mm thickness. The Hyper Red source color devices are made with Al- Low power consumption. GaInP on GaAs substrate Light Emitting Diode. Wide viewing angle. Ideal for backlight and indicator. Package: 2000pcs / reel . Moisture sensitivity level : level 3. RoHS compliant. Package Dimensions K g in ig r b t h Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAB3165 REV NO: V.22A DATE: JAN/18/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203001764 Selection Guide Part No. Emitting Color (Material) Lens Type Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. 120 Water Clear 230 *40 Hyper Red (AlGaInP) KPT-1608SURCK Typ. 2θ1/2 *80 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color λpeak Peak Wavelength Hyper Red 645 λD [1] Dominant Wavelength Hyper Red 630 Δλ1/2 Spectral Line Half-width Hyper Red 28 C Capacitance Hyper Red 35 VF [2] Forward Voltage IR Reverse Current t h Typ. Max. Units Test Conditions nm IF=20mA nm IF=20mA nm IF=20mA pF VF=0V;f=1MHz 2.5 V IF=20mA 10 uA VR=5V g in ig r b Hyper Red 1.95 Hyper Red Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. K Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA Electrostatic Discharge Threshold (HBM) 3000 V 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAB3165 REV NO: V.22A DATE: JAN/18/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203001764 Hyper Red KPT-1608SURCK t h ig r b g in K SPEC NO: DSAB3165 REV NO: V.22A DATE: JAN/18/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203001764 KPT-1608SURCK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) K g in ig r b t h Reel Dimension SPEC NO: DSAB3165 REV NO: V.22A DATE: JAN/18/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203001764 PACKING & LABEL SPECIFICATIONS KPT-1608SURCK t h ig r b g in K Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes SPEC NO: DSAB3165 REV NO: V.22A DATE: JAN/18/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203001764