1.6X0.8mm SMD CHIP LED LAMP
Part Number: KPT-1608ZGC
Green
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
1.6mmX0.8mm SMD LED, 0.75mm thickness.
The Green source color devices are made with InGaN
Low power consumption.
on Sapphire Light Emitting Diode.
Wide viewing angle.
Electrostatic discharge and power surge could damage
Ideal for backlight and indicator.
the LEDs.
Package: 2000pcs / reel .
It is recommended to use a wrist band or anti-
Moisture sensitivity level : level 3.
electrostatic glove when handling the LEDs.
All devices, equipments and machineries must be
RoHS compliant.
electrically grounded.
Package Dimensions
K
g
in
ig
r
b
t
h
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAE3256
APPROVED: Wynec
REV NO: V.13B
CHECKED: Allen Liu
DATE: MAY/19/2016
PAGE: 1 OF 5
DRAWN: L.T.Zhang
ERP: 1203003342
Selection Guide
Part No.
Emitting Color (Material)
Iv (mcd) [2]
@ 20mA
Lens Type
Viewing
Angle [1]
Min.
KPT-1608ZGC
Green (InGaN)
Typ.
2θ1/2
200
400
130°
Water Clear
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
3. Luminous intensity value is traceable to CIE127-2007 standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Emitting Color
Typ.
λpeak
Peak Wavelength
Green
515
λD [1]
Dominant Wavelength
Green
Δλ1/2
Spectral Line Half-width
Green
C
Capacitance
Green
VF [2]
Forward Voltage
IR
Reverse Current
g
in
Green
Green
Max.
t
h
Units
Test Conditions
nm
IF=20mA
nm
IF=20mA
nm
IF=20mA
pF
VF=0V;f=1MHz
4.1
V
IF=20mA
50
uA
VR=5V
ig
r
b
525
30
45
3.3
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to CIE127-2007 standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
K
Absolute Maximum Ratings at TA=25°C
Parameter
Values
Units
102.5
mW
DC Forward Current
25
mA
Peak Forward Current [1]
150
mA
5
V
450
V
Power dissipation
Reverse Voltage
Electrostatic Discharge Threshold (HBM)
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static
electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.
SPEC NO: DSAE3256
APPROVED: Wynec
REV NO: V.13B
CHECKED: Allen Liu
DATE: MAY/19/2016
PAGE: 2 OF 5
DRAWN: L.T.Zhang
ERP: 1203003342
Green
SPEC NO: DSAE3256
APPROVED: Wynec
KPT-1608ZGC
t
h
ig
r
b
g
in
K
REV NO: V.13B
CHECKED: Allen Liu
DATE: MAY/19/2016
PAGE: 3 OF 5
DRAWN: L.T.Zhang
ERP: 1203003342
KPT-1608ZGC
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Tape Dimensions
(Units : mm)
SPEC NO: DSAE3256
APPROVED: Wynec
K
g
in
REV NO: V.13B
CHECKED: Allen Liu
ig
r
b
t
h
Reel Dimension
DATE: MAY/19/2016
PAGE: 4 OF 5
DRAWN: L.T.Zhang
ERP: 1203003342
PACKING & LABEL SPECIFICATIONS
KPT-1608ZGC
t
h
ig
r
b
g
in
K
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes
SPEC NO: DSAE3256
APPROVED: Wynec
REV NO: V.13B
CHECKED: Allen Liu
DATE: MAY/19/2016
PAGE: 5 OF 5
DRAWN: L.T.Zhang
ERP: 1203003342
很抱歉,暂时无法提供与“KPT-1608ZGC”相匹配的价格&库存,您可以联系我们找货
免费人工找货