WP57YYD

T-1 3/4 (5mm) SOLID STATE LAMP Part Number: WP57YYD Yellow Features Description z Low power consumption. The Yellow source color devices are made with Gallium z Long life - solid state reliability. Arsenide Phosphide on Gallium Phosphide Yellow Light z RoHS compliant. Emitting Diode. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF2647 APPROVED: Wynec REV NO: V.7B CHECKED: Allen Liu DATE: NOV/01/2016 PAGE: 1 OF 6 DRAWN: L.T.Zhang ERP: 1101005745 Selection Guide Part No. Emitting Color (Material) Yellow (GaAsP/GaP) WP57YYD Lens Type Yellow Diffused Yellow (GaAsP/GaP) Viewing Angle [1] Iv (mcd) [2] @ 20mA Min. Typ. 6 12 6 12 2θ1/2 30° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Yellow λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 590 nm IF=20mA Yellow 588 nm IF=20mA Spectral Line Half-width Yellow 35 nm IF=20mA C Capacitance Yellow 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Yellow 2.1 V IF=20mA 2.5 Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 140 mA Operating / Storage Temperature -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. 4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAF2647 APPROVED: Wynec REV NO: V.7B CHECKED: Allen Liu DATE: NOV/01/2016 PAGE: 2 OF 6 DRAWN: L.T.Zhang ERP: 1101005745 WP57YYD Yellow SPEC NO: DSAF2647 APPROVED: Wynec REV NO: V.7B CHECKED: Allen Liu DATE: NOV/01/2016 PAGE: 3 OF 6 DRAWN: L.T.Zhang ERP: 1101005745 PACKING & LABEL SPECIFICATIONS WP57YYD Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF2647 APPROVED: Wynec REV NO: V.7B CHECKED: Allen Liu DATE: NOV/01/2016 PAGE: 4 OF 6 DRAWN: L.T.Zhang ERP: 1101005745 SPEC NO: DSAF2647 APPROVED: Wynec REV NO: V.7B CHECKED: Allen Liu DATE: NOV/01/2016 PAGE: 5 OF 6 DRAWN: L.T.Zhang ERP: 1101005745 SPEC NO: DSAF2647 APPROVED: Wynec REV NO: V.7B CHECKED: Allen Liu DATE: NOV/01/2016 PAGE: 6 OF 6 DRAWN: L.T.Zhang ERP: 1101005745