KCR1206T

KCR three-terminal capacitor/resistor EU features • • • • • Improved reduction of radiated noises Capacitor/resistor filter Noise reduction in a variety of circuits Marking: Black body color with no marking Products with lead-free terminations meet EU RoHS requirements dimensions and construction L Size W 1206 t e Glass Coating g GND Terminals (Ag + Ni, Sn Plating) e Terminals (Ag + Ni, Sn Plating) L W t g e .126±.008 .063±.008 .031±.008 .039±.012 .016±.012 (3.2±0.2) (1.6±0.2) (0.8±0.2)* (1.0±0.3) (0.4±0.3) * KCR1206T221/500: t = .043 ± .008 (1.1 ± 0.2) KCR1206T221/101: t = .043 ± .008 (1.1 ± 0.2) ordering information New Part # EMI/EMC filtering KCR Type 1206 Size 1206 T Termination Material T: Sn TE Packaging TE: 7" embossed plastic (1206 - 2,000 pieces/reel) 220/500 Capacitance/ Resistance 2 significant digits + number of zeros For further information on packaging, please refer to Appendix A. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 2/24/08 276 KOA Speer Electronics, Inc. • Bolivar Drive • P Box 547 • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com .O. KCR three-terminal capacitor/resistor circuit schematic In Out Item Operating Temperature Range Storage Temperature Range Measuring Condition (Standard) Temperature Relative Humidity Measuring Condition (Precision) Temperature Relative Humidity Specification -40°C to +85°C -40°C to +85°C 15°C to 35°C 20 - 90% 20°C ± 1°C 60 - 67% applications and ratings GND applications and ratings (continued) Part Designation KCR1206TTE220/500 KCR1206TTE220/101 KCR1206TTE470/500 KCR1206TTE470/101 KCR1206TTE101/500 KCR1206TTE101/101 KCR1206TTE221/500 KCR1206TTE221/101 Capacitance (pF) 22 22 47 47 100 100 220 220 Capacitance Tolerance Resistance (Ω) 50 100 50 100 50 100 50 100 Resistance Tolerance (%) Power Rating (W) Operating Temperature Range +50 ~ -20 ±30 1/16 -40°C to +85°C environmental applications Performance Characteristics Parameter Insulation Resistance Capacitance 1000 MΩ Minimum Within the tolerance Requirement Test Method Applied rated voltage for 60 seconds Frequency: 1kHz Voltage: 1Vrms DC: 0.3V Maximum Solder a chip to a test substrate and then laterally apply a load (5N, 500gF) in the arrow direction Chip DC Resistance Terminal Adhesion Strength Within the tolerance No physical damage Substrate Resistance to Solder Heat Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Flux: 25% rosin Preheating: 60 seconds Preheating Temperature: 150°C Solder: H60A Solder Temperature: 260°C ±5°C Dip Time: 5 seconds ± 0.5 second Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 5/15/05 KOA Speer Electronics, Inc. • Bolivar Drive • P Box 547 • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com .O. 277 EMI/EMC filtering KCR three-terminal capacitor/resistor environmental applications (continued) Performance Characteristics Parameter Solderability Requirement More than 95% of the terminal electrode shall be covered with new solder Test Method Flux: 25% rosin Preheating: 60 seconds Preheating Temperature: 150°C Solder: H60A Solder Temperature: 230°C ±5°C Dip Time: 4 seconds ± 1 second Repeat the following heat cycle 10 times: Step: 1 2 3 4 Temperature: -40°C ± 3°C Room Temp. 85°C ± 2°C Room Temp. Time: 30 minutes 15 minutes 30 minutes 15 minutes ± 3 minutes maximum ± 3 minutes maximum Temperature Cycle* Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance High Temperature Resistance* Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Appearance: No physical damage Capacitance: Within tolerance Temperature: 70°C ± 2°C Bias: 150% of rated voltage Test Time: 1000 +48/-0 hours Humidity Resistance (Unload)* Temperature: 85°C ± 2°C Humidity: 85% ± 5% Test Time: 500 +24/-0 hours Substrate Bending Test After soldering a chip to a test substrate, bend the substrate by 1 mm and then measure. The substrate is GE4 or based on GE4. 20 Substrate Weight Displacement 45 ± 2 Humidity Resistance (Load)* Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance 45 ± 2 Temperature: 40°C ± 2°C Humidity: 90 - 95% Bias: 100% of rated voltage Test Time: 500 +24/-0 hours Temperature: -40°C ± 2°C Test Time: 1000 +48/-0 hours Low Temperature Resistance (Unload)* EMI/EMC filtering Vibration The frequency of applied vibration should be swept from 10 Hz to 55 Hz and return to 10 Hz. This cycle time should be about 1 minute and this cycle should be repeated. Amplitude (Total Excursion): 1.5 mm This motion shall be applied for a period of 2 hours in each of 3 mutually perpendicular axes (total of 6 hours). * After temperature cycle test, high temperature resistance test, humidity resistance test or low temperature resistance test, the tested sample should be measured after having been left in temperature from 15°C to 35°C and relative humidity from 45% to 75% for 24 hours. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 11/01/03 278 KOA Speer Electronics, Inc. • Bolivar Drive • P Box 547 • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com .O.