KL732ATTE8N2

KOA SPEER ELECTRONICS, INC. TN-200 R7 AHA 06/28/06 Thin Film Chip Inductors Type KL73 Series 1. Scope CERTIFIED CERTIFIED This specification applies to Thin Film Chip Inductors (KL73) 1H, 1E, 1J, 2A and 2B sizes produced by KOA Corporation. 2. Dimensions and Construction c L c Marking Protective Coating Inner Electrode t d Coil Pattern Ceramic Substrate Electrode Type (Inch Size Code) L Dimensions inches (mm) W c d t .009±.001 (0.23±0.03) .014±.002 (0.35±0.05) .02±.004 (0.5±0.1) .02±.004 (0.5±0.1) .024±.004 (0.6±0.1) W 1H (0201) 1E (0402) 1J (0603) 2A (0805) 2B (1206) .024±.001 .01±.001 .003±.002 .006±.002 (0.6±0.03) (0.3±0.03) (0.08±0.05) (0.15±0.05) .039±.004 .02±.002 .006±.004 .01±.004 (1.0±0.1) (0.5±0.05) (0.15±0.1) (0.25±0.1) .063±.008 .031±.004 .012±.004 .012±.004 (1.6±0.2) (0.8±0.1) (0.3±0.1) (0.3±0.1) .079±.008 .049±.008 .016±.008 .012±.004 (2.0±0.2) (1.25±0.2) (0.4±0.2) (0.3±0.2) .126±.008 .063±.008 (3.2±0.2) (1.6±0.2) .02±.008 (0.5±0.2) .016 +.008 -.004 (0.4 +0.2 ) -0.1 Insulation Direction Mark Film 3. Type Designation The type designation shall be the following form: New Type KL73 Type 2A Size 1H: 0201 1E: 0402 1J: 0603 2A: 0805 2B: 1206 T Termination Material T: Sn (Other termination styles available, contact factory for options) TE Packaging TP: 7" Embossed Paper 2mm Pitch (1E only - 10,000 pcs/reel) TE: 7" Embossed Plastic 4mm Pitch (1J, 2A, 2B - 4,000 pcs/reel) TB: 7" Paper Tape 2mm Pitch (1H only - 10,000 pcs/reel) 4N7 Nominal Inductance 4N7: 4.7nH 47N: 47nH B: C: G: J: G Tolerance ±0.1nH ±0.2nH ±2% ±5% PAGE 1 OF 9 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 4. Application and Ratings Part Designation KL731HTTB0N6* KL731HTTB0N7* KL731HTTB0N8* KL731HTTB0N9* KL731HTTB1N0* KL731HTTB1N1* KL731HTTB1N2* KL731HTTB1N3* KL731HTTB1N5* KL731HTTB1N6* KL731HTTB1N8* KL731HTTB2N0* KL731HTTB2N2* KL731HTTB2N4* KL731HTTB2N7* KL731HTTB3N0* KL731HTTB3N3* KL731HTTB3N6* KL731HTTB3N9* KL731HTTB4N3* KL731HTTB4N7* KL731HTTB5N1* KL731HTTB5N6* KL731HTTB6N2* KL731HTTB6N8* KL731HTTB7N5* KL731HTTB8N2* KL731HTTB9N1* KL731HTTB10N* KL731HTTB11N* KL731HTTB12N* KL731HTTB13N* KL731HTTB15N* KL731HTTB16N* KL731HTTB18N* KL731HTTB20N* KL731HTTB22N* KL731HTTB24N* KL731HTTB27N* KL731HTTB33N* KL731HTTB39N* Inductance (nH) 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 11 12 13 15 16 18 20 22 24 27 33 39 Inductance Tolerance B: ±0.1nH, C: ±0.2nH Quality Factor Minimum Self Resonant Frequency Minimum (MHz) DC Resistance Maximum (Ω) Allowable DC Current Maximum (mA) Measured Frequency (MHz) B: ±0.1nH B: ±0.1nH, C: ±0.2nH 0.20 350 B: ±0.1nH B: ±0.1nH, C: ±0.2nH 0.30 9000 0.35 300 0.50 0.60 200 8000 0.70 130 1.00 5 6000 1.30 120 1.50 2.00 4000 2.50 110 500 B: ±0.1nH B: ±0.1nH, C: ±0.2nH B: ±0.1nH B: ±0.1nH, C: ±0.2nH B: ±0.1nH B: ±0.1nH, C: ±0.2nH B: ±0.1nH B: ±0.1nH, C: ±0.2nH B: ±0.1nH B: ±0.1nH, C: ±0.2nH B: ±0.1nH B: ±0.1nH, C: ±0.2nH B: ±0.1nH B: ±0.1nH, C: ±0.2nH B: ±0.1nH B: ±0.1nH, C: ±0.2nH G: ±2% G: ±2%, J: ±5% G: ±2% G: ±2%, J: ±5% G: ±2% G: ±2%, J: ±5% G: ±2% 2000 5.00 70 G: ±2% J: ±5% 1500 1000 6.00 50 800 7.00 40 200 * Add tolerance character (B, C, G, J) PAGE 2 OF 9 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 4. Application and Ratings Continued Part Designation KL731ETTPN56B KL731ETTPN68B KL731ETTPN82B KL731ETTP1N0* KL731ETTP1N2* KL731ETTP1N5* KL731ETTP1N8* KL731ETTP2N2* KL731ETTP2N7* KL731ETTP3N3* KL731ETTP3N9* KL731ETTP4N7* KL731ETTP5N6* KL731ETTP6N8* KL731ETTP8N2* KL731ETTP10N* KL731ETTP12N* KL731ETTP15N* KL731ETTP18N* KL731ETTP22N* KL731ETTP27N* KL731ETTP33N* KL731JTTE1N0* KL731JTTE1N2* KL731JTTE1N5* KL731JTTE1N8* KL731JTTE2N2* KL731JTTE2N7* KL731JTTE3N3* KL731JTTE3N9* KL731JTTE4N7* KL731JTTE5N6* KL731JTTE6N8* KL731JTTE8N2* KL731JTTE10N* KL731JTTE12N* KL731JTTE15N* KL731JTTE18N* KL731JTTE22N* KL731JTTE27N* KL731JTTE33N* KL731JTTE39N* KL731JTTE47N* KL731JTTE56N* KL731JTTE68N* KL731JTTE82N* Inductance (nH) 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 Inductance Tolerance Quality Factor Minimum Self Resonant Frequency Minimum (MHz) 14000 DC Resistance Maximum (Ω) 0.10 700 Allowable DC Current Maximum (mA) Measured Frequency (MHz) B: ±0.1nH 7 12000 10000 B: ±0.1nH C: ±0.2nH 8000 6000 5000 4000 3000 2500 G: ±2% J: ±5% 2000 1500 0.15 0.20 0.25 0.30 0.50 1.00 650 600 550 500 450 350 300 250 200 200 500 10 1.50 2.00 3.00 5.00 7 150 1000 10 15 13000 0.10 10000 C: ±0.2nH 20 8000 6000 5000 4000 3000 2500 2000 G: ±2% J: ±5% 1500 1000 10 600 2.50 1.50 200 0.50 0.15 0.25 650 450 500 350 25 1.0 250 150 200 120 4.00 4.50 5.00 100 * Add tolerance character (B, C, G, J) PAGE 3 OF 9 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 4. Application and Ratings Continued Part Designation KL732ATTE1N0* KL732ATTE1N2* KL732ATTE1N5* KL732ATTE1N8* KL732ATTE2N2* KL732ATTE2N7* KL732ATTE3N3* KL732ATTE3N9* KL732ATTE4N7* KL732ATTE5N6* KL732ATTE6N8* KL732ATTE8N2* KL732ATTE10N* KL732ATTE12N* KL732ATTE15N* KL732ATTE18N* KL732ATTE22N* KL732ATTE27N* KL732ATTE33N* KL732ATTE39N* KL732ATTE47N* KL732ATTE56N* KL732ATTE68N* KL732ATTE82N* KL732BTTE2N2* KL732BTTE2N7* KL732BTTE3N3* KL732BTTE3N9* KL732BTTE4N7* KL732BTTE5N6* KL732BTTE6N8* KL732BTTE8N2* KL732BTTE10N* KL732BTTE12N* KL732BTTE15N* KL732BTTE18N* KL732BTTE22N* KL732BTTE27N* KL732BTTE33N* KL732BTTE39N* KL732BTTE47N* KL732BTTE56N* KL732BTTE68N* KL732BTTE82N* KL732BTTE100* Inductance (nH) 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 Inductance Tolerance Quality Factor Minimum Self Resonant Frequency Minimum (MHz) 13000 10000 9000 C: ±0.2nH 8000 800 6000 25 5000 4500 4000 3000 2500 2000 1500 1000 15 800 700 600 9000 7000 6000 5000 4500 4000 3500 3000 2500 40 G: ±2% J: ±5% 25 2000 1.00 1500 500 4.00 5.00 150 1.50 200 200 1.00 300 250 500 700 0.50 500 400 900 0.25 DC Resistance Maximum (Ω) Allowable DC Current Maximum (mA) Measured Frequency (MHz) 20 G: ±2% J: ±5% 20 10 25 C: ±0.2nH 0.25 1000 900 900 0.50 800 500 35 1000 2.00 400 200 500 15 400 200 * Add tolerance character (B, C, G, J) PAGE 4 OF 9 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 6. Characteristics 6-1 Test Condition Unless otherwise specified, the standard range of atmospheric conditions for marking measurements and tests is as follows: Ambient temperature: 20 ± 15°C Relative humidity: 65 ± 20% If there may be any doubt on results, measurements shall be made within the following limits: Ambient temperature: 20 ± 2°C Relative humidity: 65 ± 5% 6-2 Measurement Method of L and Q Test equipment: Fixture: Measuring frequency: Hewlett Packard RF Impedance analyzer 4191A Hewlett Packard Test fixture 16092A 500 MHz/1.0nH ~ 22nH (1.0nH ~ 15nH) 200 MHz/27nH ~ 100nH (18nH ~ 47nH) 1. Perform auto-calibration to the HP4191A .275" (7 mm) unknown connector connected to 0Ω/0S/50Ω standard terminations. 2. Connected the test fixture 16092A. Measure the open circuit admittance (Go, Bo), and the short circuit impedance (Ro, Xo). Ro Xo Rx Gm + j Bm 4191A Caribration plane Go Bo Xx 16092A Spring clip fixture Coil Gm Ro Go Rx + jBm: + jXo: + jBo: + jXx: Measured admittance [S] Residual impedance [Ω] Stray admittance [S] Unknown impedance [Q] 3. Set pattern up and ground side to direction mark on insulator. Measure admittance (Gm, Bm). Chip inductor (Face up) Spring clip Insulator (Teflon) .118 (3.0) .039 (1.0) Grand plane Terminal Cross section of 16092A See table 0402 0603 0805 1206 .055 (1.4) .071 (1.8) .106 (2.7) .031 (0.8) Thickness: .040 (1.0) .118 (3.0) Dimensions of insulator (Teflon) in inches (mm) 4. The L and Q value shall be given the following equation. (Compensated calculation) Rx = Xx = Gm - Go - Ro (Gm - Go) 2+ (Bm - Bo)2 Bo - Bm - Xo (Gm - Go) 2- (Bm - Bo)2 L= L: Inductance of coil Q: Quality factor of coil f: Measuring frequency Xx 2πf I , Q = Xx Rx 814-362-5536 I PAGE 5 OF 9 Fax 814-362-8883 I Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 USA I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 6-3 Characteristics Item Insulation resistance Requirement More than 104 MΩ Test Method DC 500V, 1 minute between both terminals and center of reverse side. V More than 103 MΩ DC 500V, 1 minute Between both terminals and center of protection coating. V Dielectric withstanding voltage Without distinct damage DC 500V, 1 minute Between both terminals and center of protection coating. V Terminal strength ∆ R/R: Within ± 1% ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% No mechanical damage by cracks or stripping, etc. Soldered chip on wiring board A for test is to be bent down to .079" (2 mm) - 0603, .118" (3 mm) - 0402, 0805 and 1206 as below drawing. (Set condition) Dimensions in inches (mm) Wiring board A for test Chip coil Support (ø5) Solder 1.77 (45.0) .786 (20) Within ±2 1.77 (45.0) 1.97 (50) Weight R230 .118 (3.0) Ohmmeter PAGE 6 OF 9 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 6-3 Characteristics Continued Item Vibration Requirement ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction 95% of the terminal should be covered with new solder ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance and construction. Insulation resistance: more than 50MΩ ∆ L/L: Within ± 2% ∆ Q/Q: Within ± 20% Without distinct damage in appearance, construction and marking Test Method Inflict 2 hours in each direction of X, Y, Z at vibration of JIS C 5025 (1978) type A - 0603; 10 ~ 55Hz, amplitude .059" (1.5 mm) - 0402, 0805 and 1206 260 ± 5°C, 10 ± 1 second Resistance to solder heat Solderability Shock resistance 230 ± 5°C, 3 ± 0.5 second Inflict the impulse 3 times to both directions (total 18 times) along perpendicular axis that test condition C of JIS C 5026 (1974) table-1 - 0603; 100G, 6 months - 0402, 0805 and 1206 -40°C ± 3°C, 1,000 ± 4 hours Low temperature operation Heat resisting property 125°C ± 2°C, 1,000 ± 4 hours Temperature cycling -40 ± 3°C, 30 minutes/125 ± 2°C, 30 minutes 100 cycles Humidity 40 ± 2°C, 90 ~ 95% RH 1,000 ± 4 hours Resistance to solvent Immerse 30 ± 5 seconds in the regent (20 ~ 25°C) of JIS K 8839 (1995) PAGE 7 OF 9 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 5. Marking 5-1 Coating and Marking Color Coating color: Dark blue Direction mark color: Yellow 0603 Inductance value shall be indicated to two letters marking of figures and alphabet. (Example of marking) L1 1.0nH 56 5.6nH 10 10nH H6 47nH See marking item on page 2, rating table. Direction mark 5-2 Marking Method 0402 Inductance value shall have no marking. Direction marking only. 0805 Inductance value shall be indicated to two letters marking, including decimal point. (Example of marking) 2.2 2.2nH 5.6 5.6nH 10 10nH 47 47nH Direction mark 56 5.6 Decimal point 1206 Inductance value shall be indicated to two letters marking of significant figures. An alphabetical letter N shall replace position of decimal point. Direction (Example of marking) 2N2 2.2nH 5N6 5.6nH 10 10nH 47 47nH mark 5N6 Decimal point .010 (0.25 ± 0.1) .069 (1.75 ± 0.1) .059 (1.5 ± 0.1) .157 (4.0 ± 0.1) D 7. Packaging 7-1 Taping The tapes for taping shall be embossed carrier tapes of .315" (8 mm) width and .157" (4 mm) pitches. The standard quantity per reel shall be 4,000 pieces. Tapes for size 0402 (only) shall be paper carrier tapes of .315" (8 mm) width and .079" (2 mm) pitches. .138 (3.5 ± 0.05) .315 (8.0 ± 0.2) Direction of mark 5N6 C A (1) Dimensions of carrier tape Dimensions in inches (mm) B E Tape running direction Size 0402 0603 0805 1206 A B C D E .018 .026 .045 .079 .079 (0.45 ± 0.2) (0.65 ± 0.1) (1.15 ± 0.1) (2.0 ± 0.05) (2.0 ± 0.05) .035 .043 .075 .079 .157 (0.90 ± 0.1) (1.1 ± 0.15) (1.9 ± 0.15) (2.0 ± 0.01) (4.0 ± 0.1) .037 .057 .094 (0.95 ± 0.1) (1.45 ± 0.15) (2.4 ± 0.2) .037 .074 (0.95 ± 0.1) (1.9 ± 0.2) .137 (3.5 ± 0.2) .079 (2.0 ± 0.1) .079 (2.0 ± 0.1) .157 (4.0 ± 0.1) .157 (4.0 ± 0.1) PAGE 8 OF 9 I Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. TN-200 R7 (2) Reel dimensions 11.80 (300 ± 20 ) 0 4,000 pieces 13.76 (350 ± 20 ) 0 5.90 (150 ± 20 ) 0 Top tape Empty Empty Tape running direction Marking place .079 (2 ± 0.5) .511 (13 ± 0.5) 7.00 (178 ± 2.0) Dimensions in inches (mm) (Marking item) (1) Type designation (2) Nominal inductance (3) Quantity (4) Production lot number (5) Manufacturer's name 2.36 (60 ± 2.0) .393 (10 ± 1.5) .448 (11.4 ± 1.5) 8. Recommended Soldering Condition 8-1 Dimensions of Standard Land C A Solder resist Dimensions in inches (mm) Size 0402 - 1E 0603 - 1J A .016 ~ .020 (0.4 ~ 0.5) .031 ~ .039 (0.8 ~ 1.0) .047 ~ .055 (1.2 ~ 1.4) .079 ~ .094 (2.0 ~ 2.4) B .012 ~ .020 (0.3 ~ 0.5) .016 ~ .031 (0.4 ~ 0.8) .035 ~ .051 (0.9 ~ 1.3) .047 ~ .063 (1.2 ~ 1.6) C .016 ~ .020 (0.4 ~ 0.5) .016 ~ .031 (0.4 ~ 0.8) .016 ~ .031 (0.4 ~ 0.8) .016 ~ .031 (0.4 ~ 0.8) B Chip coil 0805 - 2A Land 1206 - 2B 8-2 Soldering Condition Reflow soldering should be done at 240°C within 20 seconds. Flow soldering should be done at 260°C within 10 seconds. Please use suitable solder quantity, too much solder may affect performance of product. Solder Solder 9. Recommended Washing Condition Isopropyl alcohol and methyl alcohol used for the washing process will not affect the part performance. Ultrasonic cleaning should be changed to condition for size of printed wiring board and type of oscillator. Overpowering of ultrasonic cleaning will cause problems according to resonant phenomenon. Condition of ultrasonic cleaner should be confirmed prior to use. We recommend the following conditions: Ultrasonic power: Within 20W/1 Cleaning times: Within 5 minutes Bolivar Drive I 10. Storage Chip inductors should not be stored under high temperature and high humidity conditions. In particular, do not store taping where it is exposed to heat or direct sunlight. Otherwise, the packing material may be deformed, causing problems during mounting. PAGE 9 OF 9 USA I P.O. Box 547 I Bradford, PA 16701 I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.