KQ0603TTE4N3

KOA SPEER ELECTRONICS, INC. SS-214 R8 AHA 6/28/06 Chip Inductors Type KQ 0603 1. Scope of Application This specification applies to chip inductors KQ series produced by KOA corporation. CERTIFIED CERTIFIED 2. Dimensions and Construction L W1 Flat Top Film t h d Magnetic Inner Wire Coating W2 Ceramic/Ferrite Core Electrode Size Code 0603 L .063±.004 (1.6±0.1) Dimensions inches (mm) W1 W2 t h d .039±.004 .033±.004 .035±.004 .01±.006 .014±.004 (1.0±0.1) (0.85±0.1) (0.9±0.1) (0.25±0.15) (0.35±0.1) 3. Type Designation Type designation shall be as the following form. New Type KQ Type 0603 Size T Termination Material T: Sn (Other termination styles available, contact factory for options) TE Packaging TE: 7" Embossed Plastic TD: 7" Paper Tape 10N Nominal Inductance 10N: 10nH R10: 0.1µH 1R0: 1.0µH J Tolerance G: ±2% J: ±5% K: ±10% 0603 PAGE 1 OF 6 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-214 R8 4. Standard Applications Part Designation KQ0603TTE1N6* KQ0603TTE1N8* KQ0603TTE3N3* KQ0603TTE3N6* KQ0603TTE3N9* KQ0603TTE4N3* KQ0603TTE4N7* KQ0603TTE5N1* KQ0603TTE6N8* KQ0603TTE7N5* KQ0603TTE8N2* KQ0603TTE8N7* KQ0603TTE9N5* KQ0603TTE10N* KQ0603TTE11N* KQ0603TTE12N* KQ0603TTE15N* KQ0603TTE16N* KQ0603TTE18N* KQ0603TTE22N* KQ0603TTE23N* KQ0603TTE24N* KQ0603TTE27N* KQ0603TTE30N* KQ0603TTE33N* KQ0603TTE36N* KQ0603TTE39N* KQ0603TTE43N* KQ0603TTE47N* KQ0603TTE51N* KQ0603TTE56N* KQ0603TTE68N* KQ0603TTE72N* KQ0603TTE82N* KQ0603TTER10* KQ0603TTER11* KQ0603TTER12* KQ0603TTER15* KQ0603TTER18* KQ0603TTER20* KQ0603TTER21* KQ0603TTER22* KQ0603TTER25* KQ0603TTER27* KQ0603TTER33* KQ0603TTER39* KQ0603TTER47* KQ0603TTER56* Marking C 0 X E 1 F G Y 2 H A J B 3 K 4 5 L 6 7 S M 8 N 9 P 0 Q 1 T 2 3 4 5 6 7 8 9 0 U V 1 W 2 3 4 5 6 Nominal Inductance (nH) 1.6 1.8 3.3 3.6 3.9 4.3 4.7 5.1 6.8 7.5 8.2 8.7 9.5 10 11 12 15 16 18 22 23 24 27 30 33 36 39 43 47 51 56 68 72 82 100 110 120 150 180 200 210 220 250 270 330 390 470 560 L Measuring Frequency Inductance Tolerance Q Quality Factor Minimum 24 16 Q Self Resonant DC Allowable Measuring Frequency Resistance DC Current Frequency Minimum Maximum Maximum (MHz) (MHz) (Ω) (mA) 0.03 12500 0.045 0.055 0.063 6900 0.08 5900 0.063 0.116 0.115 5800 0.11 0.106 4800 0.12 700 4600 0.109 0.125 4800 0.13 0.086 250 4000 0.13 0.17 3300 0.104 3100 0.17 0.19 3000 2700 0.15 0.135 2650 0.22 2800 2250 0.144 2300 0.22 2080 0.25 2200 600 2000 200 1900 0.28 0.30 0.31 0.34 0.49 0.54 0.58 0.61 0.65 0.92 2.2 2.3 2.5 2.4 2.3 3.0 3.7 1.21 2.09 J: ±5% K: ±10% 22 20 27 28 31 33 250 35 34 35 38 37 40 37 40 38 40 39 38 37 G: ±2% J: ±5% K: ±10% 200 1700 34 150 32 150 1400 1350 1300 1400 1300 1200 1000 900 800 700 640 560 400 300 280 140 130 120 170 100 80 190 130 25 100 24 100 NEW 50 J: ±5% K: ±10% 30 50 * Add tolerance character (G, J, K) PAGE 2 OF 6 I Bolivar Drive I P.O. Box 547 Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-214 R8 4. Standard Applications (continued) Part Designation KQ0603TTER68* KQ0603TTER82* KQ0603TTE1R0* KQ0603TTE1R2* Marking 7 8 9 0 Nominal Inductance (nH) 680 820 1000 1200 L Measuring Frequency Inductance Tolerance Q Quality Factor Minimum Q Self Resonant DC Allowable Measuring Frequency Resistance DC Current Frequency Minimum Maximum Maximum (MHz) (MHz) (Ω) (mA) 540 490 440 400 1.97 3.09 5.13 5.45 140 110 90 80 NEW 50 J: ±5% K: ±10% 30 50 5. Rating Item Storage temperature range Operating temperature range 5.1 Measurement Method Nominal Inductance Range 1.6 nH to 1200 nH Specification -40°C ~ +100°C -40°C ~ +125°C Test Equipment 4291A RF Impedance analyzer Fixture 16193A Test fixture Setup E.L = 1.4 cm OSC = 500 mV Measuring Frequency Listed Table-1 6. Test Conditions Unless otherwise specified, the test shall be performed at the temperature of 20 ± 15°C and at a relative humidity of 65 ± 20%. Reverse test conditions shall be performed at the temperature of 20 ± 2°C and at a relative humidity of 65 ± 5%. 7. Reliability Tests 7.1 Electrical Characteristics Item Dielectric withstanding voltage Insulation resistance Flammability Requirement No evidence of flaming, fuming, or breakdown 1000MΩ and over IEC 695-2-2 Test Methods 5 seconds at AC 500 V applied between both terminals and film. 1 minute at DC 100 V measured between both terminals and film. Withstands needle-flame test. PAGE 3 OF 6 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-214 R8 7.2 Mechanical Characteristics Item Terminal pull strength Terminal bending strength Vibration Requirement No evidence of damage No evidence of breakdown Test Methods Terminals shall withstand a pull of 5 N in a horizontal direction. Specimen shall be soldered on bend test board and force applied to the opposite side to cause a 3 mm deflection 2 hours in each direction of X, Y, Z, on PCB at a frequency range of 10-55-10Hz with 1.5 mm amplitude Dropping 1 m on the ground of concrete 1 time Immerse in the solder at 260 ± 5°C for 10±1 seconds Immerse in the solder at 230 ± 5°C for 3 ± 0.5 seconds Accordance with MIL-STD-202F Method 215 ∆L/L within ± 5% ∆Q/Q within ± 10% No evidence of damage ∆L/L within ± 5% ∆Q/Q within ± 10% No evidence of outer damage ∆L/L within ± 5% ∆Q/Q within ± 10% 95% of the terminal should be covered with new solder No damage and marking must remain legible Dropping Resistance to soldering heat Solderability Resistance to solvent 7.3 Environmental Characteristics Item Low temperature storage High temperature storage Moisture endurance Requirement No evidence of damage ∆L/L within ± 5% ∆Q/Q within ± 10% No evidence of damage ∆L/L within ± 5% ∆Q/Q within ± 10% No evidence of damage ∆L/L within ± 5% ∆Q/Q within ± 10% No evidence of damage ∆L/L within ± 5% ∆Q/Q within ± 10% Test Methods Store at -40 ± 2°C, for 1000 hours Store at +125 ± 2°C, for 1000 hours Store at 40 ± 2°C, 90 ~ 95% RH for 1000 hours Biased to full rated current at +125°C for 1000 hours Load life Unless otherwise specified, measurements shall be performed within 2 hours after leaving test samples for more than one hour at the normal temperature and at the normal humidity. Bolivar Drive I PAGE 4 OF 6 www.koaspeer.com P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-214 R8 7.3 Environmental Characteristics (continued) Item High temperature High humidity Thermal shock Requirement No evidence of damage ∆L/L within ± 5% ∆Q/Q within ± 10% No evidence of damage ∆L/L within ± 5% ∆Q/Q within ± 10% ∆L/L within ± 5% Test Methods Biased to 10% rated current at +85°C, 85% RH for 1000 hours 100 cycles between -40°C/hour and +125°C/hour ∆L/L to be measured at the temperature of between -40°C and +125°C as based on the inductance at 20°C Temperature characteristics Unless otherwise specified, measurements shall be performed within 2 hours after leaving test samples for more than one hour at the normal temperature and at the normal humidity. 8. Packaging 8.1 Taping The tapes for taping shall be embossed carrier tapes of .315" (8 mm) width and .157" (4 mm) pitches. The standard quantity per reel shall be 2,000 pieces. (1) Dimensions of Carrier Tape .010 (0.25 ± 0.05) Feeding hole* .059 .043 (1.5 ± 0.1 ) (1.1 ± 0.05) 0 Chip pocket .069 (1.75 ± 0.1) .138 (3.5 ± 0.05) .315 (8.0 ± 0.1) Chip inductor .047 .069 .157 .157 (1.2 ± 0.1) (1.75 ± 0.1) (4.0 ± 0.1) (4.0 ± 0.1) Dimensions in inches (mm) .024 .079 * 10 Pitches accumulation of feeding (0.6 ± 0.05) (2.0 ± 0.05) holes shall be 1.57" (40 ± 0.2 mm). Top tape peeling strength: 0.1 N ~ 0.7N Tape running direction (2) Taped Configurations (conforming to EIA-481 standard) Empty space Chip mounting space Empty space Leader space End 6.29 (160) min. Dimensions in inches (mm) 9.04 (230) min. Drawing out direction I Beginning 6.29 (160) min. PAGE 5 OF 6 I Bolivar Drive I P.O. Box 547 Bradford, PA 16701 USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-214 R8 (3) Reel Dimensions and Indication .448 (11.4 ± 1.0) .079 (2.0 ± 0.5) .511 (13 ± 0.2) 2.36 (60 ± 1.0) .826 (21 ± 0.8) Indicate position The following items shall be indicated on the reel. • Type (KQ 0603 TE) • Nominal inductance and tolerance • Quantity • Production lot number • Manufacturer’s name or trade mark 7.08 (180 +0 ) -3 Dimensions in inches (mm) .354 (9.0 ± 0.3) 9. General Information (1) Storage Chip inductors shall not be stored under high temperature and high humidity conditions. Especially, do not store taping where they are exposed to heat or direct sunlight. Otherwise, the packing material may be deformed, causing problems during mounting. (2) Mounting Placement force should not be excessive. (3) Soldering Flow soldering should be done at 260°C for less than 10 seconds. Reflow soldering should be done at 240°C for less than 30 seconds. When using a soldering iron, temperature shall not exceed 350°C and within 3 seconds. Soldering iron time of each electrode shall be allowed only one time. After soldering, chip inductors shall not be stressed excessively. (4) Cleaning It is no problem to use organic solvents. Since this chip inductor is a coil of ultra-fine wire, it is susceptible to vibration. If an ultra-sonic cleaning unit is used for cleaning, check for any possibility of problem generation before practical use since such cleaning units considerably differ in vibration level and mode. Although the conditions differ depending on the printed board size, ultrasonic cleaning is generally used in the conditions described below as examples. Power: Within 20 W/L Cleaning times: Within 5 minutes (5) Pattern design The land pattern is recommended as follows. .076 (1.92) Inductor position Solder resist .006 (0.16) .040 (1.02) .025 (0.64) Dimensions in inches (mm) PAGE 6 OF 6 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.