LPC10065ATED152M

KOA SPEER ELECTRONICS, INC. SS-216 R4 AHA 6/30/06 Power Chip Inductors Type LPC10065 1. Scope CERTIFIED CERTIFIED This specification applies to LPC10065 power chip inductors produced by KOA Corporation. 2. Dimensions and Construction E D F C F Electrode Ceramic Magnet Substrate Wire Ferrite Core A B Size 10065 A B Dimensions inches (mm) C D E .354 (9.0) F .098±.008 (2.5±0.2) ø.394±.008 .295 Max. .409±.008 .315±.008 (ø10.0±0.2) (7.5 Max.) (10.4±0.2) (8.0±0.2) 3. Type Designation The type designation shall be the following form: New Type LPC Type 10065 Size A Termination Material A: SnAg (Other termination styles available, contact factory for options) TED Packaging TED: 10" Embossed Plastic 300 pcs/reel 101 Nominal Inductance 101: 100µH 221: 220µH 152: 1500µH K Tolerance K: ±10% M: ±20% 10065 PAGE 1 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-216 R4 4. Rating Part Designation LPC10065ATEDR68M LPC10065ATED1R0M LPC10065ATED1R5M LPC10065ATED2R2M LPC10065ATED3R3M LPC10065ATED4R7M LPC10065ATED6R8M LPC10065ATED100K LPC10065ATED150K LPC10065ATED220K LPC10065ATED330K LPC10065ATED470K LPC10065ATED680K LPC10065ATED101K LPC10065ATED151K LPC10065ATED221K LPC10065ATED331K LPC10065ATED471K LPC10065ATED681K LPC10065ATED102K LPC10065ATED152K LPC10065ATED222K LPC10065ATED332K Inductance (µH) 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1000 1500 2200 3300 Inductance Tolerance Quality Factor Minimum (MHz) 40 M: ±20% 30 20 K: ±10% 15 Self Resonant Frequency Minimum (MHz) 75.0 65.0 50.0 40.0 30.0 25.0 20.0 15.0 12.0 9.0 8.0 6.0 5.0 4.0 3.0 2.5 2.0 1.5 1.0 0.95 0.85 0.70 0.55 DC Resistance Maximum (Ω) 6.0 mΩ 7.0 mΩ 8.0 mΩ 9.0 mΩ 0.012 0.017 0.024 0.036 0.054 0.080 0.120 0.175 0.255 0.380 0.580 0.850 1.30 1.85 2.70 4.00 6.10 9.00 13.5 Allowable DC Current Maximum (Amps) 9.50 9.00 8.50 7.50 6.80 5.70 4.70 3.90 3.15 2.60 2.30 1.79 1.48 1.22 1.00 0.82 0.67 0.57 0.47 0.38 0.31 0.26 0.21 Measured Frequency (Hz) L Meas. Freq. 1 MHz Q Meas. Freq. 2.52 MHz K: ±10% 30 100 MHz 4.1 Rating No. 1 2 Item Storage temperature range Operating temperature range Specification -40°C ~ +85°C -30°C ~ +85°C PAGE 2 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-216 R4 5. Reliability Test Item DC Super-imposition Resistance to soldering heat Vibration Requirement ∆L/L within -5% No evidence of outer damage ∆L/L shall be within ±5% ∆L/L within ±5% ∆L/L within ±5% Test Methods Inductance when the allowable current is applied Solder 260 ± 5°C/10 sec 2 hours in each direction of X, Y, Z, at a frequency range of 10 ~ 55 ~10Hz with 1.5 mm amplitude -40 ± 2°C/0.5 Hr 85 ± 2°C/0.5 Hr 100 cycles 85°C 0.5 Hr -40°C Heat shock High temperature leaving Low temperature leaving Moisture leaving ∆L/L within ±5% ∆L/L within ±5% ∆L/L within ±5% Store at 85 ± 2°C 500 Hrs. Store at -40 ± 2°C 500 Hrs. 40 ± 2°C 90 ~ 95% RH 500 Hrs. 6. Taping 6.1 Dimensions of Tape .629 (16 ± 0.1) .079 (2.0 ± 0.1) .069 (1.75 ± 0.1) ø.059 (ø1.5 ± 0.1) .157 (4.0 ± 0.1) .452 .944 (11.5 (24 ± ± 0.1) 0.3) .016 (0.4) Dimensions in inches (mm) .275 (7 ± 0.2) .433 (11.0) .452 (11.5) Embossed tape Top tape peeling strength: .008 ~ .027 (0.2N ~ 0.69N) Direction of feed End Blank 1.57 (40mm min.) Chip mounting Blank 1.97 (50 mm min.) Beginning Tape leader 5.90 (150 mm min.) PAGE 3 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-216 R4 6.2 Dimensions and Marking Dimensions in inches (mm) .079 (2.0) ø.826 (ø21.0) ø3.15 (ø80) The following items shall be indicated on the reel. Type: LPC10065 (1) Nominal inductance and tolerance (2) Quantity (3) Production lot number (4) Manufacturer's name or trade mark Recommended PAD dimension ø.511 (ø13.0) ø14.943 (ø380) .079 (2.0) 1.02 (26.0) Soldering pad Dimensions in inches (mm) .236 (6.0) 6.3 Performance Type LPC10065 60 50 2.2mH 1.5mH 1000 µH 1.0mH 680µH 470µH 330µH 220µH 150µH 100 µH 100µH 68µH 47µH 33µH 22µH 15µH 10µH 10 µH 6.8µH 4.7µH 3.3µH 2.2µH 100mA 1,000mA DC-Current Q-f Characteristics Type LPC10065 60 50 Q Factor 40 30 20 10 0 10KHz 100KHz 1MHz Frequency 10MHz 1.0 µH 2.2 µH 3.3 µH 4.7 µH 6.8 µH Q Factor 60 50 40 30 20 10 0 Q Factor 40 30 20 10 0 .157 (4.0) .197 (5.0) .157 (4.0) Q-f Characteristics Type LPC10065 10 µH 2.2 µH 6.8 µH 4.7 µH Inductance 10KHz 3.3 µH 100KHz 1MHz 10MHz Frequency 60 50 Q Factor 40 30 20 10 0 Q-f Characteristics Type LPC10065 680 µH 330 µH 100 µH 220 µH 10KHz 100KHz 1MHz Frequency 10MHz Q-f Characteristics Type LPC10065 1 mH 1.5 mH 2.2 mH 10KHz 100KHz 1MHz Frequency 10MHz PAGE 4 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.