KOA SPEER ELECTRONICS, INC.
SS-198 R6
AHA 6/29/06
Surface Mount Power Chip Inductors Type LPC12065
1. Scope
CERTIFIED
CERTIFIED
This specification applies to LPC12065 power chip inductors produced by KOA Corporation.
2. Dimensions and Construction
E D F C F Electrode Ceramic Magnet Substrate Wire Ferrite Core A B Size 12065 A B Dimensions inches (mm) C D
E .433 (11.0)
F .146±.112 (3.7±0.3)
ø.472±.008 .295 Max. .488±.008 .472±.008 (ø12.0±0.2) (7.5 Max.) (12.4±0.2) (10.0±0.2)
3. Type Designation The type designation shall be the following form: New Type
LPC
Type
12065
Size
A
Termination Material
A: SnAg (Other termination styles available, contact factory for options)
TED
Packaging
TED: 10" Embossed Plastic 300 pcs/reel
101
Nominal Inductance
101: 100µH 221: 220µH 152: 1500µH
K
Tolerance
K: ±10% M: ±20% N: ±30%
12065
PAGE 1 OF 4 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-198 R6
4. Rating
Part Designation LPC12065ATEDR68N LPC12065ATED1R0N LPC12065ATED1R5N LPC12065ATED2R2N LPC12065ATED3R3M LPC12065ATED4R7M LPC12065ATED6R8M LPC12065ATED100K LPC12065ATED150K LPC12065ATED220K LPC12065ATED330K LPC12065ATED470K LPC12065ATED680K LPC12065ATED101K LPC12065ATED151K LPC12065ATED221K LPC12065ATED331K LPC12065ATED471K LPC12065ATED681K LPC12065ATED102K LPC12065ATED152K LPC12065ATED222K LPC12065ATED332K LPC12065ATED472K LPC12065ATED682K Inductance (µH) 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 470 680 1.0 mH 1.5 mH 2.2 mH 3.3 mH 4.7 mH 6.8 mH Inductance Tolerance Quality Factor Minimum (MHz) Self Resonant Frequency Minimum (MHz) 77.0 60.0 47.0 38.0 30.0 24.0 19.0 15.0 12.0 9.5 7.5 6.2 4.9 4.0 3.2 2.5 2.0 1.6 1.3 1.0 0.83 0.67 0.53 0.43 0.34 DC Resistance Maximum (Ω) 5.0 mΩ 7.0 mΩ 8.0 mΩ 10.0 mΩ 0.012 0.016 0.022 0.031 0.046 0.065 0.093 0.130 0.182 0.260 0.380 0.540 0.790 1.08 1.55 2.21 3.20 4.60 6.60 9.30 13.2 Allowable DC Current Maximum (Amps) 10.0 9.50 9.00 8.00 7.00 6.50 5.40 4.50 3.63 3.00 2.40 2.05 1.70 1.38 1.14 0.94 0.77 0.65 0.53 0.44 0.35 0.29 0.23 0.19 0.16 Measured Frequency (Hz)
N: ±30%
40
M: ±20%
30
2.52 MHz
20
K: ±10%
15
100 KHz
30
4.1 Rating No. 1 2 Item Storage temperature range Operating temperature range Specification -40°C ~ +85°C -30°C ~ +80°C
PAGE 2 OF 4 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-198 R6
5. Reliability Test
Item DC Super-imposition Resistance to soldering heat Vibration Requirement ∆L/L within -5% No evidence of outer damage ∆L/L shall be within ±5% ∆L/L within ±5% ∆L/L within ±5% Test Methods Inductance when the allowable current is applied Solder 260 ± 5°C/6 ± 10 seconds 2 hours in each direction of X, Y, Z, at a frequency range of 10 ~ 55 ~10Hz with 1.5 mm amplitude -40 ± 2°C/0.5 Hr 85 ± 2°C/0.5 Hr 100 cycles 85°C 0.5 Hr
-40°C
Heat shock
High temperature storage Low temperature storage Moisture resistance
∆L/L within ±5% ∆L/L within ±5% ∆L/L within ±5%
Store at 85 ± 2°C 500 Hrs. Store at -40 ± 2°C 500 Hrs. 40 ± 2°C 90 ~ 95% RH 500 Hrs.
6. Taping 6.1 Dimensions of Tape
Dimensions in inches (mm) .629 (16 ± 0.1) .079 (2.0 ± 0.1) .069 (1.75 ± 0.1) ø.059 (ø1.5 ± 0.1) .157 (4.0 ± 0.1) .452 .944 (11.5 (24 ± ± 0.1) 0.3) .275 (7 ± 0.2)
.016 (0.4)
.492 (12.5)
.511 (13.0) Embossed tape Top tape peeling strength: .008 ~ .027 (0.2N ~ 0.69N) Direction of feed
Blank 1.57 (40mm min.)
Products 300 pieces
Blank 1.97 (50 mm min.)
Tape leader 5.90 (150 mm min.)
PAGE 3 OF 4 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-198 R6
6.2 Dimensions and Marking
Dimensions in inches (mm)
.079 (2 ± .05)
ø.826 (ø21 ± 0.8)
ø3.15 (ø80)
Reel/300 pieces maximum. The following items shall be indicated on the reel. Type: LPC12065 (1) Nominal inductance and tolerance (2) Quantity (3) Production lot number (4) Manufacturer's name or trade mark Recommended PAD dimension
ø.511 (ø13 ± 0.5) ø9.83 (ø250)
.079 (2.0) 1.02 (26.0)
Soldering pad
Dimensions in inches (mm)
.295 (7.5)
.197 (5.0)
.197 (5.0)
.197 (5.0)
6.3 Performance
Type LPC12065 6.8mH 4.7mH 3.3mH 2.2mH 1.5mH 1000 µH 1.0mH 680µH 470µH 330µH 220µH 150µH 100 µH 100µH 68µH 47µH 33µH 22µH 15µH 10µH 10 µH 6.8µH 4.7µH 3.3µH 2.2µH 0.1A 1.0A DC-Current 10A 60 50 Q Factor 40 30 20 10 0 10KHz 47 µH 10 µH 33 µH 68 µH 100KHz 1MHz Frequency 10MHz Q-f Characteristics Type LPC12065 22 µH
Inductance
60 50 Q Factor 40 30 20 10 0
Q-f Characteristics Type LPC12065
680 µH 100 µH 220 µH 470 µH 10KHz 100KHz 1MHz Frequency 6.8 µH 4.7 µH 3.3 µH 330 µH 10MHz
60 50 Q Factor 40 30 20 10 0
Q-f Characteristics Type LPC12065 1.0 µH 1.5 µH Q Factor 4.7 µH 6.8 µH 3.3 µH 10KHz 100KHz 1MHz Frequency 10MHz 60 50 40 30 20 10 0
Q-f Characteristics Type LPC12065
2.2 µH 1.0 µH 10KHz 100KHz 1MHz Frequency 10MHz
PAGE 4 OF 4 Bolivar Drive
I
P.O. Box 547
I
Bradford, PA 16701
I
USA
I
814-362-5536
I
Fax 814-362-8883
I
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
很抱歉,暂时无法提供与“LPC12065ATED152M”相匹配的价格&库存,您可以联系我们找货
免费人工找货