MHL1ECTTPR12

SS-222 R12 12/6/06 10:36 AM Page 1 SS-222 R12 AHA 12/06/06 Multilayer Ceramic Inductors Type MHL 1. General ■ ■ ■ ■ ■ CERTIFIED CERTIFIED Monolithic structure provides high reliability in a wide temperature and humidity range High quality ceramic material and unique manufacturing process provides high Q at high frequency Standard EIA packages: 1E, 1J Nickel barrier with solder overcoat for excellent solderability Marking: Brown body color with no marking (1E) White body color with with black stripe and no marking (1J) 2. Dimensions W L Solder Plating Ni Plating Silver Metallization d Size Code 1E (0402) 1J (0603) L .039±.004 (1.0±0.1) .063±.006 (1.6±0.15) Dimensions inches (mm) W t .02±.004 (0.5±0.1) .031±.006 (0.8±0.15) .02±.004 (0.5±0.1) .031±.006 (0.8±0.15) d .01±.004 (0.25±0.1) .012±.008 (0.30±0.2) t Terminations (Metallization Bands) d Electrodes 3. Type Designation The type designation shall be in the following form: MHL Type 1E Size 1E 1J C Material Permeability Code: C T T Termination Material T: Sn (Other termination styles available, contact factory for options) TE Packaging TP: 7" paper tape 2mm pitch (1E only - 10,000 pcs/reel) TD: 7" paper tape (1J - 4,000 pcs/reel 3N9 Nominal Inductance 3N9 = 3.9nH R10 = 100nH S Tolerance S: ±0.3nH J: ±5% PAGE 1 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com S p e c i fi c a ti o n s g i ve n h e r e i n m a y b e c h a n g e d a t a n y ti m e w i th o u t p r i o r n o t i ce . P l e a se co n fi r m t e ch n ic a l sp e c i fi c a ti o n s b e fo r e yo u o r d e r a n d / o r u s e . SS-222 R12 12/6/06 10:36 AM Page 2 SS-222 R12 4. Standard Applications Part Designation MHL1ECTTP1N0* MHL1ECTTP1N2* MHL1ECTTP1N5* MHL1ECTTP1N8* MHL1ECTTP2N2* MHL1ECTTP2N7* MHL1ECTTP3N3* MHL1ECTTP3N9* MHL1ECTTP4N7* MHL1ECTTP5N6* MHL1ECTTP6N8* MHL1ECTTP8N2* MHL1ECTTP10N* MHL1ECTTP12N* MHL1ECTTP15N* MHL1ECTTP18N* MHL1ECTTP22N* MHL1ECTTP27N* MHL1ECTTP33N* MHL1ECTTP39N* MHL1ECTTP47N* MHL1ECTTP56N* MHL1ECTTP68N* MHL1ECTTP82N* MHL1ECTTPR10* NEW Inductance L (nH) 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 27 33 Inductance Tolerance Self Resonant Frequency Minimum Typical Typical Typical (100MHz) (100MHz) (800MHz) (MHz) 37 10000 36 Q DC Resistance Maximum () 0.12 0.13 0.14 0.16 0.17 0.19 0.22 0.24 0.27 0.32 0.37 0.42 0.50 0.55 0.65 0.8 0.9 1.0 1.2 1.3 1.4 Allowable DC Current Maximum (mA) Operating Temperature Range S: ±0.3nH 34 6000 4000 32 11 8 31 30 J: ±5% 28 26 24 23 21 19 16 –– –– 3900 3500 3200 2600 2300 2000 1600 1400 1200 1100 900 750 300 -55°C to +125°C 200 10 180 150 100 600 1.6 MHL1ECTTPR12* MHL1JCTTD1N5* MHL1JCTTD1N8* MHL1JCTTD2N2* MHL1JCTTD2N7* MHL1JCTTD3N3* MHL1JCTTD3N9* MHL1JCTTD4N7* MHL1JCTTD5N6* MHL1JCTTD6N8* MHL1JCTTD8N2* MHL1JCTTD10N* MHL1JCTTD12N* MHL1JCTTD15N* MHL1JCTTD18N* MHL1JCTTD22N* MHL1JCTTD27N* MHL1JTTTD27N* MHL1JCTTD33N* 8 S: ±0.3nH 14 6000 0.10 100 0.13 0.15 0.20 0.23 0.20 0.28 0.30 0.35 0.40 0.45 0.50 0.55 0.60 500 10 46 4000 5800 3200 2600 2300 2000 1600 1400 1200 -55°C to +125°C 15 J: ±5% 12 18 15 600 *Add tolerance character (S, J) PAGE 2 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com S p e c i fi c a ti o n s g i ve n h e r e i n m a y b e c h a n g e d a t a n y ti m e w i th o u t p r i o r n o t i ce . P l e a se co n fi r m t e ch n ic a l sp e c i fi c a ti o n s b e fo r e yo u o r d e r a n d / o r u s e . SS-222 R12 12/6/06 10:36 AM Page 3 SS-222 R12 4. Standard Applications (continued) Part Designation MHL1JCTTD39N* MHL1JTTTD39N* MHL1JCTTD47N* MHL1JCTTD56N* MHL1JCTTD68N* MHL1JCTTD82N* MHL1JCTTDR10* MHL1JCTTDR12* MHL1JCTTDR15* MHL1JCTTDR18* MHL1JCTTDR22* Inductance L (nH) 39 39 47 56 68 82 100 120 150 180 220 Inductance Tolerance Self Resonant Frequency Minimum Typical Typical Typical (100MHz) (100MHz) (800MHz) (MHz) Q 15 17 12 J: ±5% 15 46 39 37 36 29 16 8 13 1100 900 700 600 500 400 DC Resistance Maximum () 0.65 0.70 0.75 0.80 0.85 0.90 1.0 1.2 1.3 1.5 500 400 Allowable DC Current Maximum (mA) Operating Temperature Range -55°C to +125°C 300 — *Add tolerance character (S, J) PAGE 3 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com S p e ci fi c a t io n s g i ve n h e r e i n m a y b e ch a n g e d a t a n y ti m e w i th o u t p r i o r n o t i ce . P le a se co n fi r m t e ch n i ca l sp e c i fi c a ti o n s b e fo r e y o u o r d e r a n d / o r u s e . SS-222 R12 12/6/06 10:36 AM Page 4 SS-222 R12 5. Characteristics Item Operating Temperature Storage Temperature Requirement -55°C to +125°C 40°C @ 70% Humidity Sealed plastic bags with desiccant shall be used to reduce the potential of oxidation on the terminations during storage. Flux: 5-10 sec dip After Flux: Air dry for 15 sec Preheat: 150°C ±10°C Preheat Time: 60 sec Solder Temp: 260°C ±5°C Dip Time: 10 ±1 sec Flux: 5-10 sec dip After Flux: Air dry for 15 sec Solder Temp: 245°C ±5°C Dip Time: 5 ±0.5 sec The bead shall be subjected to the following 5 steps for the period of time shown below. The 5 steps constitute one (1) rotation. 4 rotations shall be carried out. 1) Flux: 5-10 sec 2) After Flux: Air dry for 15 sec 3) Solder Temp: 230°C ±5°C 4) Dip Time: 5 ±0.5 sec 5) Cool: Air cool for 60 seconds Conditions Resistance to Solder Heat Change in Impedance: Relative to value before test ±20%. Appearance: There shall be no cracking Solder Coverage: More than 75% of the terminal electrode shall be covered with solder. Solderability Solder Coverage: More than 95% of the termination shall be covered with solder. Leach Resistance Appearance: There shall be no visible signs of physical or mechanical damage (i.e. no cracks) Terminations: Termination must not be leached away for more than 5%. Insulation Resistance Solvent Resistance Insulation Resistance: Min 1G ohms Change in Impedance: Relative to value before test ±10%. Cleaning by: Washer: Ultrasonic washer (100W) Solvent: Isopropyl alcohol Time: 3 minutes Type 1E 1J Type 1E 1J W(kgf) –– 0.5 W(kgf) –– 1.4 Time N/A 30 sec ±2 sec Time N/A 60 sec Terminal Strength (hanging test) Appearance: The terminal electrode shall not break off, nor shall there be damage to the body. Terminal Strength (push test) Appearance: There shall be no evidence of mechanical degradations to terminals or body. Bending Strength Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value before test ±10% Board: 90x40x1.6mm Bend: 1mm Time: 5 sec PAGE 4 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com S p e c i fi c a ti o n s g i ve n h e r e i n m a y b e c h a n g e d a t a n y ti m e w i th o u t p r i o r n o t i ce . P l e a se co n fi r m t e ch n ic a l sp e c i fi c a ti o n s b e fo r e yo u o r d e r a n d / o r u s e . SS-222 R12 12/6/06 10:36 AM Page 5 SS-222 R12 5. Characteristics (continued) Item Mechanical Shock Requirement Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value before test ±10% Impedance: Relative to initial value ±10% Conditions Force: 50G Time: 11 msec There shall be 3 shocks in each of 6 directions (18 shocks total). Only endurance conditioning by sweeping shall be made. The entire frequency range from 10-2,000 Hz and return to 10 Hz in 20 minutes (this shall constitute one cycle). Amplitude: 15G The test shall have a 15G peak and shall be applied for a period of 4 hours (12 cycles) in each of 3 mutually perpendicular directions (a total of 36 cycles within a total of 12 hours). Step 1-start 2-hold 3-transfer 4-hold 5-transfer Temperature -40°C ±2°C -40°C ±2°C — +105°C ±2°C — Time — 30 min ±5 min 0.5 min max. 30 min ±5 min 0.5 min max. Vibration Thermal Shock Appearance: There shall be no physical or mechanical damage. Impedance: Relative to initial value ±20%. DCR: The DCR shall not exceed initial specified value. Testing of the parts will be made at 0 hours, 250 hours and 500 hours. Before testing the parts shall be allowed to cool to room temperature for 24 hours. Steps 1 thru 5 constitute one complete cycle and the test shall consist of a total of 500 cycles. Temperature: 85°C ±2°C Relative Humidity: 85% Time: 1,000 hours total Apply: 100% rated current Load Humidity Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value ±15% Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. Life Test Appearance: There shall be no physical or mechanical damage Impedance: Relative to initial value ±15% Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. Temperature: 85°C ±2°C Time: 1,000 hours total Apply: 100% rated current 6. Packaging Specifications KOA’s multilayer components are provided on tape-and-reel for use in pick-and-place machines. The reel size is 7 inch. PAGE 5 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com S p e c i fi c a ti o n s g i ve n h e r e i n m a y b e c h a n g e d a t a n y ti m e w i th o u t p r i o r n o t i ce . P l e a se co n fi r m t e ch n ic a l sp e c i fi c a ti o n s b e fo r e yo u o r d e r a n d / o r u s e . SS-222 R12 12/6/06 10:36 AM Page 6 SS-222 R12 7. Dimensions - inches (mm) Tape 1E 1J Ao .026±.004 (0.67±0.1) .045±.004 (1.15±0.1) Bo .046±.004 (1.17±0.1) .073±.004 (1.85±0.1) Ko .025±.004 (0.63±0.1) .043±.004 (1.1±0.1) E F Do Po P2 t W Bo D1 P1 Ao Ko Tape 1E 1J E .069±.004 (1.75±0.10) F .138±.002 (3.5±.005) W .315±.008 (8.0±0.2) P1 .079±.009 (2.0±0.23) Po .079±.004 (2.0±0.1) P2 Do D1 .039 min. (1.0 min.) t .009±.001 (0.23±0.02) .079±.002 .059±.004 (2.0±0.05) (1.5+0.1/-0.0) 8. Chip Quantities Per Reel Chip Size 0402 (1005) 0603 (1608) Parts on 7 inch Parts on 13 inch (178mm) Reel (330mm) Reel 10,000 4,000 –––––– 4,000 9. Recommended PC Board Land Patterns - inches (mm) Chip Size 1E (0402) 1J (0603) L .05 (1.3) .102 (2.6) G .015 (0.4) .023 (0.6) H .019 (0.5) .031 (0.8) H G L 10. Recommended Temperature Profiles for Soldering Recommended Temperature Profile for Wave Soldering Soldering 10 Seconds Max. Preheat 100 Seconds Max. 250°C Natural Cooling 230°C Recommended Temperature Profile for Reflow Soldering Preheat 100 Seconds Max. Soldering 10 Seconds Max. Natural Cooling 200°C 150°C 60 Seconds Max. 150°C 60 Seconds Max. 20 Seconds Max. PAGE 6 OF 6 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com S p e c i fi c a ti o n s g i ve n h e r e i n m a y b e c h a n g e d a t a n y ti m e w i th o u t p r i o r n o t i ce . P l e a se co n fi r m t e ch n ic a l sp e c i fi c a ti o n s b e fo r e yo u o r d e r a n d / o r u s e .