PSEDTEL50J

PSI – EOL PSE – NOT RECOMMENDED FOR NEW DESIGN RECOMMENDED REPLACEMENT PSJ2, TLR3AP PSI, PSE chip type power shunt resistor EU features current sense • Smooth current flow, suitable for large current detecting • Flat structure, applicable for strong mounting • Automatic mounting machines are applicable • Products with lead-free terminations meet EU RoHS and China RoHS requirements • AEC-Q200 Qualified dimensions and construction PSE Type L (Inch Size Code) PSI (3920) W Electrode: Cu Metal Solder t d Resin PSE (2525) Resist. (Ω) 3.0m 4.0m 0.5m, 1.0m 1.5m, 2.0m L Dimensions inches (mm) W d t .394±.010 .205±.010 .079±.010 .028±.010 (10.0±0.25) (5.2±0.25) (2.0±0.25) (0.7±0.25) .026±.010 .252±.010 .252±.010 .087±.010 (0.65±0.25) (6.4±0.25) (6.4±0.25) (2.2±0.25) .019±.010 (0.50±0.25) Resistive Element: Metal Alloy PSI L W Electrode: Cu Metal Solder t d Resistive Element: Metal Alloy ordering information PS Type I D Power Rating I: 3W E: 3W E: 5W Termination Material D: SnAgCu For further information on packaging, please refer to Appendix A. TEB Packaging TE: embossed plastic (PSE: 2,000 pieces/reel) TEB: embossed plastic (PSI: 3,000 pieces/reel) 3L00 Nominal Resistance ±1%: 4 digits ±5%: 3 digits All values less than 0.1Ω (100mΩ) are expressed in mΩ with “L” as decimal Ex: 1mΩ = 1L00 Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. F Tolerance F: ±1% J: ±5% 10/01/19 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com 119 PSI – EOL PSE – NOT RECOMMENDED FOR NEW DESIGN RECOMMENDED REPLACEMENT PSJ2, TLR3AP PSI, PSE chip type power shunt resistor applications and ratings current sense Resistance Range Part Designation Power Rating T.C.R. (ppm/°C) Max. F: ±1% J: ±5% Rated Terminal Part Temperature PSI 3W ±50 3mΩ, 4mΩ –– +105°C ±150 0.5mΩ, 1.0mΩ 1.5mΩ, 2.0mΩ 0.5mΩ, 1mΩ, 1.5mΩ, 2mΩ 0.5mΩ, 1mΩ: +105°C 1.5mΩ: 85°C 2mΩ: +70°C +105°C 3W PSE Operating Temperature Range 5W -65°C to +155°C environmental applications Derating Curve PSI, PSE (3W) PSE (5W) 80 80 % Rated Power 100 % Rated Power 100 60 40 20 0 1.5m 2m 60 0.5m 1m 40 20 -60 -40 -65 -20 80 100 120 105 Terminal Part Temperature (°C) 0 20 40 60 140 155 0 -60 -40 -65 -20 80 100 120 70 85 105 Terminal Part Temperature (°C) 0 20 40 60 140 155 For resistors operated at a terminal part temperature of described for each size or above, a power rating shall be derated in accordance with the derating curve. Please refer to “Introduction of the derating curve based on the terminal part temperature” in the beginning of our catalog before use. Performance Characteristics Parameter T.C.R. Overload (Short time) Resistance to Solder Heat Requirement ∆ R ±% Limit Typical Within specified –– T.C.R. ±0.2%: PSI ±0.1%: PSI ±0.5%: PSE ±0.2%: PSE ±0.5% ±0.1% Test Method +25°C/+100°C 15W for 5 seconds 260°C ± 5°C, 15 seconds ± 1 second Rapid Change of Temperature ±0.5% ±0.2% -55°C (30 minutes), +125°C (30 minutes), 1,000 cycles Moisture Resistance ±0.5% ±0.2% 85°C ± 2°C, 85% RH, 1000 hours, 10% Bias Endurance at and Less of Terminal Part Temperature ±1.0% ±0.2%: PSI ±0.6%: PSE Low Temperature Exposure ±0.5% High Temperature Exposure ±1% ±0.02%: PSI ±0.1%: PSE ±0.4%: PSI ±0.6%: PSE Terminal part temperature: 105°C (PSI, PSE (3W), PSE (5W) 0.5m, 1.0m) +85°C (PSE (5W) 1.5m) +70°C (PSE (5W) 2.0m), 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle -65°C, 96 hours +155°C, 1,000 hours Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 120 10/01/19 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com