RK73B1JTTD134J

RK73B general purpose 2%, 5% tolerance thick film chip resistor resistors EU features • Products with lead-free terminations meet EU RoHS requirements. EU RoHS regulation is not intended for Pb-glass contained in electrode, resistor element and glass. • AEC-Q200 Qualified: 0201 (1H), 0402 (1E), 0603 (1J), 0805 (2A), 1206 (2B), 1210 (2E), 2010 (2H/W2H), 2512 (3A/W3A/W3A2) dimensions and construction L c c W Solder Plating Ni Plating t d Protective Coating Resistive Inner Film Electrode Ceramic Substrate Derating Curve 100 80 80 60 40 1F 1E, 1H, 1J, 2A, 2B, 2E, 2H, 3A, W2H, W3A 3A, W2H, W3A 20 0 % Rated Power 100 1H, 1E, 1J, 2A, 2B, 2E, W2H, W3A (1W) 60 W3A2 40 20 0 20 40 60 80 100 120 140 160 180 70 125 155 Ambient Temperature (°C) For resistors operated at an ambient temperature of 70°C or above, a power rating shall be derated in accordance with the above derating curve. 0 -60 -40 -55 -20 0 20 40 60 80 100 120 140 160 95 125 155 Terminal Part Temperature (°C) RK73B 2B Type Size 1F 1H 1E 1J 2A 2B 2E W2H W3A 2H 3A New W3A2 L T Termination Material T: Sn (1F ~ W3A2) Contact factory for below options: L: SnPb (1E, 1J, 2A, 2B, 2E, 2H, 3A) G: Au (1E ~ 2A: 10Ω ~ 1MΩ) t 1F (01005) .015±.001 .007±.001 .004±.001 .004±.001 .005±.001 (0.4±0.02) (0.2±0.02) (0.10±0.03) (0.11±0.03) (0.13±0.02) 1H (0201) .024±.001 .012±.001 .004±.002 .006±.002 .009±.001 (0.6±0.03) (0.3±0.03) (0.1±0.05) (0.15±0.05) (0.23±0.03) 1E (0402) .039 1J (0603) .063±.008 .031±.004 .012±.004 .012±.004 .018±.004 (1.6±0.2) (0.8±0.1) (0.3±0.1) (0.45±0.1) (0.3±0.1) 2A (0805) .079±.008 .049±.004 .016±.008 (2.0±0.2) (1.25±0.1) (0.4±0.2) 2B (1206) .063±.008 .126±.008 (1.6±0.2) (3.2±0.2) .102±.008 (2.6±0.2) 2E (1210) 2H (2010) W2H (2010) For resistors operated at a terminal part temperature of described for each size or 3A above, a power rating shall be derated in (2512) accordance with the above derating curve. Please refer to “Introduction of the derating W3A/W3A2 curve based on the terminal part temperature” (2512) in the beginning of our catalog before use. ordering information Dimensions inches (mm) W c d Type* (Inch Size Code) (1.0 +.004 -.002 +0.1 ) -0.05 +.002 .02±.002 .008±.004 .01 -.004 .014±.002 (0.5±0.05) (0.2±0.1) (0.25 +0.05) (0.35±0.05) -0.1 .197±.008 .098±.008 (5.0±0.2) (2.5±0.2) .012 (0.3 .016 (0.4 +.008 -.004 +0.2 ) -0.1 .02±.004 (0.5±0.1) +.008 -.004 +0.2 ) -0.1 .02±.012 .026±.006 .024±.004 (0.5±0.3) (0.65±0.15) (0.6±0.1) .016 (0.4 .248±.008 .122±.008 (6.3±0.2) (3.1±0.2) +.008 -.004 +0.2 ) -0.1 .026±.006 (0.65±0.15) * Parentheses indicate EIA package size codes. TD Packaging TX: 01005 only: 4mm width - 1mm pitch plastic embossed TBL: 01005 only: 2mm pitch pressed paper TA: 0201 only: 1mm pitch pressed paper TC: 0201 only: 7" 2mm pitch pressed paper (TC: 10,000 pcs/reel, TCM: 15,000 pcs/reel) TCD: 0201 only: 10" 2mm pitch pressed paper TPD: 0402 only: 10" plastic embossed TPL: 0402 only: 2mm pitch punched paper TP: 0402, 0603 & 0805: 7" 2mm pitch punched paper TD: 0603, 0805, 1206 &1210: 7" 4mm pitch punched paper TDD: 0603, 0805, 1206 &1210: 10" paper tape TE: 0805, 1206, 1210, 2010 & 2512: 7" plastic embossed TED: 0805, 1206, 1210, 2010 & 2512: 10" plastic embossed 102 Nominal Resistance 2 significant figures + 1 multiplier “R” indicates decimal on value