SDR0604TTEB101Y

KOA SPEER ELECTRONICS, INC. SS-264 R1 AHA 6/30/06 Fixed High-Frequency Inductors Type SDR 0604 (SMD Power Chokes) 1. Scope CERTIFIED CERTIFIED This specification applies to SMD type choke coil SDR0604 produced by KOA Speer Electronics, Inc. 2. Dimensions & Construction B Size F A 0604 A Dimensions inches (mm) B F (typ.) .177±.012 (4.5±0.3) .071 (1.8) .220±.008 (5.6±0.2) Electrode Ceramic Magnet Substrate Wire 3. Type Designation Type designation shall be as the following form. SDR Type 0604 Size T Termination Material T: Sn (Other termination styles available, contact factory for options) TEB Packaging TEB: 13" Embossed Plastic (0604: 1,500 pieces/reel) 100 Nominal Inductance 100: 10µH 101: 100µH M Tolerance K: ±10% M: ±20% Y: ±15% 0604 4. PCB Pattern .228 (5.8) Dimensions in inches (mm) .067 .236 (1.7) (6.0) PAGE 1 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-264 R1 5. Applications & Ratings Part Designation SDR0604TTEB3R3M SDR0604TTEB3R9M SDR0604TTEB4R7M SDR0604TTEB5R6M SDR0604TTEB6R8M SDR0604TTEB8R2M SDR0604TTEB100M SDR0604TTEB120M SDR0604TTEB150Y SDR0604TTEB180Y SDR0604TTEB220Y SDR0604TTEB270Y SDR0604TTEB330K SDR0604TTEB390K SDR0604TTEB470K SDR0604TTEB560K SDR0604TTEB680K SDR0604TTEB820K SDR0604TTEB101K SDR0604TTEB121K SDR0604TTEB151K SDR0604TTEB181K SDR0604TTEB221K Nominal Inductance L (µH) @ 1KHz 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 Inductance Tolerance DC Resistance Maximum (Ω) 0.06 0.07 0.07 0.08 0.08 0.09 0.10 0.12 0.14 0.15 0.19 0.22 0.25 0.32 0.37 0.42 0.52 0.60 0.70 0.93 1.10 1.38 1.57 Allowable DC Current Maximum (Amps) 2.0 1.9 1.8 1.7 1.6 1.5 1.45 1.4 1.3 1.25 1.1 1.0 0.88 0.80 0.72 0.68 0.62 0.58 0.52 0.48 0.40 0.38 0.35 Operating Temperature Range Storage Temperature Range M: ±20% Y: ±15% -40°C to +85°C -40°C to +125°C K: ±10% PAGE 2 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-264 R1 6. Mechanical Performance Item Resistance to Vibration Resistance to Soldering Solderability Performance Change of Inductance: ±5% No remarkable visual damage The electrode shall be covered with new solder Test Method (JIS C 5321) To put the sample on paper phenolic resin laminate base and to vibrate at the frequency of 10-55-10 Hz for each X, Y, Z direction for 2 hours and to sweep it at a full vibration width .059" (1.5mm) for 1 minute. To immerse into Solder bath of 260 ± 5 °C for 10 ± 1 seconds. To immerse for 3 ± 0.5 seconds at 235 ± 5 °C 7. Environmental Tests Item Resistance to Cold Temperature Cycling Resistance to Heat T. C. R Resistance to Damp (Steady State) Endurance (Under Damp and Load) Endurance (Under high Temperature) Performance Change of Inductance: ±10% Change of Inductance: ±10% Change of Inductance: ±10% Change of Inductance: ±5% Change of Inductance: ±10% Change of Inductance: ±10% Change of Inductance: ±10% Test Method (JIS C 5321) To leave in a bath at -40 ± 2 °C for 1,000 hours. To keep at -25°C ~ 85°C for 30 minutes in 5 cycles and leave for 10 ~ 15 minutes in normal temperature at the time of transition between low temperatures and high temperatures To leave in a bath at 85 ± 2 °C for 2 hours. (Resistance to heat of Ferrite Core: 120°C) 20°C shall be standard and change of inductance shall be measured at -25°C ~ 85°C. Temperature: 60 ± 2 °C Humidity: 90 ~ 95% Test hours: 1,000 hours Temperature: 40 ± 2 °C Humidity: 90 ~ 95% To supply allowable current for 1,000 hours continually Temperature: 85 ± 2 °C To supply allowable current for 1,000 hours PAGE 3 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-264 R1 8. Packaging Carrier Tape Reels T .079 (2.0±0.5) B A øC N Thickness .004 (0.1 max.) øC Embossed cavity Embossed carrier G D Materials: Paper Plastics Dimensions in inches (mm) Type 0604 A 12.99 (330) B .512 (12 ± 0.5) C .512 (13 ± 0.5) D .472 (12) G .551 (14 max) N 1.97 (50 min) T .724 (18.4) * SDR0604: 1,500 Pieces/Reel End .157 (4.0) Start .472 (12) Cover tape No component 7.86 (200) .315 (8.0) Component User direction of feed No component 15.73 (400) ** Strength of cover tape: The force for tearing off cover tape is 10 to 130 grams in the arrow direction. 165 to 180° Top cover tape Base tape PAGE 4 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.