SDR1006TTEB101K

KOA SPEER ELECTRONICS, INC. SS-202 R5 AHA 6/30/06 Fixed High-Frequency Inductors Type SDR1006 (SMD Power Chokes) 1. Scope This specification applies to SMD type choke coil SDR1006 produced by KOA Speer Electronics, Inc. 2. Dimensions B Size F A 1006 A CERTIFIED CERTIFIED Dimensions inches (mm) B F (typ.) .217±.012 (5.5±0.3) .114 (2.9) .374±.012 (9.5±0.3) Electrode Ceramic Magnet Substrate Wire 3. Type Designation The type designation shall be in the following form: SDR Type 1006 Size 1006 T Termination Material T: Sn (Other termination styles available, contact factory for options) TEB Packaging TEB: 13" Embossed Plastic (1006: 800 pieces/reel) 100 Nominal Inductance 100: 10µH 101: 100µH M Tolerance K: ±10% M: ±20% 4. Structure Item (1) Core: (2) Winding Wire: (3) Terminal Electrode: Materials Ferrite dr. core Enameled copper wire Ag + Sn/Pb 5. PCB Pattern A Size B C Dimensions inches (mm) A B C .39 (10.0) .11 (2.8) .39 (10.0) 1006 PAGE 1 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-202 R5 6. Test Condition Unless otherwise specified, the test shall be performed at the temperature of 15 ~ 35°C and the humidity of 25 ~ 85% specified in JIS-C-5001. If there is any question about the results, the test shall be performed at the temperature of 20 ± 2 °C and the humidity of 65 ± 5%. If there is any question about measurement of absolute, the inductance shall be measured by LCR-meter without using its jig. 7. Symbol of Nominal Inductance & Tolerance (A) When we indicate the nominal inductance by numerals, the unit shall be “µH” and indicated by 3 numerals. The first 2-digits mean significant figures and the last digit means numbers of “ZERO”. The decimal points shall be indicated by “R”, which are all significant figures. Example: 1R0. . . . . . . . . 1µH 100 . . . . . . . . 10µH 470. . . . . . . . . 47µH 101 . . . . . . . 100µH 221 . . . . . . . 220µH 820. . . . . . . . 820µH (B) The tolerance of nominal inductance shall be K (± 10%), M (± 20%), Y (± 15%), which will be indicated after figures of inductance. 8. Rating Part Designation SDR1006TTEB100M SDR1006TTEB120M SDR1006TTEB150M SDR1006TTEB180M SDR1006TTEB220M SDR1006TTEB270M SDR1006TTEB330K SDR1006TTEB390K SDR1006TTEB470K SDR1006TTEB560K SDR1006TTEB680K SDR1006TTEB820K SDR1006TTEB101K SDR1006TTEB121K SDR1006TTEB151K SDR1006TTEB181K SDR1006TTEB221K SDR1006TTEB271K SDR1006TTEB331K SDR1006TTEB391K SDR1006TTEB471K SDR1006TTEB561K SDR1006TTEB681K SDR1006TTEB821K Nominal Inductance L (µH) @ 1KHz 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 Inductance Tolerance DC Resistance Maximum (Ω) 0.06 0.07 0.08 0.09 0.10 0.11 0.12 0.14 0.17 0.19 0.22 0.25 0.35 0.40 0.47 0.63 0.73 0.97 1.15 1.30 1.48 1.90 2.25 2.55 Allowable DC Current Maximum (Amps) 2.60 2.45 2.25 2.15 1.95 1.75 1.50 1.35 1.25 1.15 1.10 1.00 0.97 0.89 0.78 0.72 0.66 0.57 0.52 0.48 0.42 0.33 0.28 0.24 Operating Temperature Range Storage Temperature Range M: ±20% -40°C to +85°C -40°C to +105°C K: ±10% PAGE 2 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-202 R5 9. Mechanical Performance Item Body Strength Performance No damage Test Method (JIS C 5321) Load 1kg. for 10 seconds 1R R: The top of loading stick L: Slot-width SDR1006: .236" (6.0 mm) L Resistance to Vibration Resistance to Soldering Solderability Change of Inductance: ±5% No remarkable visual damage The electrode shall be covered with new solder To put the sample on paper phenolic resin laminate base and to vibrate at the frequency of 10-55-10 Hz for each X, Y, Z direction for 2 hours and to sweep it at a full vibration width .059" (1.5mm) for 1 minute. To immerse into Solder bath of 260 ± 5 °C for 10 ± 1 seconds. To immerse for 3 ± 0.5 seconds at 235 ± 5 °C 10. Environmental Tests Item Resistance to Cold Temperature Cycling Resistance to Heat T. C. R Resistance to Damp (Steady State) Endurance (Under Damp and Load) Endurance (Under high Temperature) Performance Change of Inductance: ±10% Change of Inductance: ±10% Change of Inductance: ±10% Change of Inductance: ±5% Change of Inductance: ±10% Change of Inductance: ±10% Change of Inductance: ±10% Test Method (JIS C 5321) To leave in a bath at -40 ± 2 °C for 1,000 hours. To keep at -25°C ~ 85°C for 30 minutes in 5 cycles and leave for 10 ~ 15 minutes in normal temperature at the time of transition between low temperatures and high temperatures To leave in a bath at 85 ± 2 °C for 2 hours. (Resistance to heat of Ferrite Core: 120°C) 20°C shall be standard and change of inductance shall be measured at -25°C ~ 85°C. Temperature: 60 ± 2 °C Humidity: 90 ~ 95% Test hours: 1,000 hours Temperature: 40 ± 2 °C Humidity: 90 ~ 95% To supply allowable current for 1,000 hours continually Temperature: 85 ± 2 °C To supply allowable current for 1,000 hours PAGE 3 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-202 R5 SDR1006 Packaging Carrier Tape Reels T .079 (2.0±0.5) B A øC N Thickness .004 (0.1 max.) øC Embossed cavity Embossed carrier Materials: Paper Plastics Type 1006 A 12.98 (330) B .944 (24 ± 1) G Dimensions in inches (mm) C .511 ± .02 (13 ± 0.5) G 1.02 (26) N 1.97 (50 Min.) T 1.24 (31.5) End .157 (4.0) Start A Cover tape B * .014 (t=0.35) No component 7.86 (200) Component User direction of feed ** Strength of cover tape: The force for tearing off cover tape is 10 to 130 grams in the arrow direction. 165 to 180° Top cover tape Size 1006 C No component A .944 (24) Dimensions inches (mm) B C .26 (6.7) .114 (12) Base tape PAGE 4 OF 4 Bolivar Drive I P.O. Box 547 I Bradford, PA 16701 I USA I 814-362-5536 I Fax 814-362-8883 I www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.