KK1117-1.25

TECHNICAL DATA THREE-TERMINAL ADJUSTABLE OUTPUT POSITIVE VOLTAGE REGULATORS KK317 The KK317 is adjustable 3-terminal positive voltage regulator capable of supplying in excess of 1.5 A over an output voltage range of 1.2 V to 37 V. These voltage regulator is exceptionally easy to use and require only two external resistors to set the output voltage. Further, it employ internal current limiting, thermal shutdown and safe area compensation, making them essentially blow-out proof. The KK317 serve a wide variety of applications to make a programmable output regulator, or by connecting a fixed resistor between the adjustment and output, the KK 317 series can be used as a precision current requlator. TO-220 AB Pin 1. Ajust 2. Vout 3. Vin (Heatsink surface connected to Pin 2.) Standard application Vi n Vout R1 Ñ in* 0.1µF A djust R2 Ño** 1µF • Output Current in Excess of 1.5 Ampere • Output Adjustable between 1.2 V and 37 V • Internal Thermal Overload Protection • Internal Short - Circuit Current Limiting Constant with Temperature • Output Transistor Safe-Area Compensation • Floating Operation for High Voltage Applications • Standard 3-lead Transistor Packages • Eliminates Stocking Many Fixed K K 317 ∗ = Cin i s r equi r ed i f r egul at or i s l ocat ed an appr eci abl e di st ance f r om power suppl y f i l t er . ∗∗ = C o i s not needed for st abi l i t y ; however , i s does i mpr ove t r ansi ent r esponse. . Vout = 125V (1 + R2 )+ ∗ R2 R1 I ADJ Si nce I AD J i s cont r ol l ed t o l ess t hen 100 µA, t he error associ at ed wi t h t hi s t erm i s negl i gi bl e i n most appl i cat i ons. Maximum ratings Rating Input - Output Voltage Differential Power Dissipation and Thermal Characteristics Operating Junction Temperature Rang Storage Junction Temperature Rang Symbol Vi - Vo PD TJ Tstg Value 40 Internally Limited -0 to +150 -65 to +150 Unit Vdc °C °C 1 KK317 Electrical characteristics (Vi-Vo= 5.0V, Io = 0.5 A, TJ = Tlow to Thigh (see Note 1); Imax = 1.5 A and Pmax = 20 W unless otherwise noted) Characteristic Line Regulation (TA=+25°C) 3.0V ≤ Vi - Vo ≤40 V Load Regulation(TJ=+25°C) 10mA≤Io≤Imax, Vin ≤5V Vin≥5 V Thermal Regulation (TA=+25°C) 20 ms Pulse Adjustment Pin Current Adjustment Pin Current Change 2.5 ≤ Vi - Vo ≤ 40 V 10mA ≤IL≤ Imax, PD ≤ Pmax Reference Voltage (Note 4) 3.0 ≤ Vi - Vo ≤ 40 V 10mA ≤IL≤ Imax, PD ≤ Pmax Line Regulation (Note 3) 3.0 V ≤ Vi - Vo ≤40 V Load Regulation (Note 3) 10mA≤Io≤Imax, Vin ≤5V Vin≥5 V Temperature Stability (Tlow ≤ Tj ≤ Ttigh) Minimum Load Current to Maintain Regulation (Vi - Vo = 40 V) Maximum Output Current Vi - Vo≤ 15 V , P ≤ 20 W Vi - Vo = 40 V, P ≤20W, TA=+25°C RMS Nose , % of Vo TA=+25°C, 10 Hz ≤ f ≤ 10 kHz Ripple Rejection, Vo = 10 V, f = 120 Hz (Note 5) Without Cadj Cadj = 10 µF Long-Term Stability, Tj = Thigh (Note 6) TA=+25°C for Endpoint Measurements Thermal Resistance Junction to Case Symbol Regline Regload IAdj ∆IAdj 5.0 0.1 0.03 50 0.2 25 0.5 0.07 100 5.0 mV %/Vo %/W µA µA Min Typ 0.01 Max 0.04 Unit %/V Vref 1.2 1.25 1.3 V Regline Regload - 0.02 0.07 %/V Ts ILmin Imax - 20 0.3 0.7 3.5 70 1.5 10 %/V %/V mA A N RR 1.5 0.15 - 2.2 0.4 0.003 - %/Vo dB S RθJC 66 - 65 80 0.3 5.0 1.0 - %/1.0 k Hrs. °C/W Notes: (1) Tlow = 0 °C , Thigh = +125 °C (2) Imax = 0.5 A , Pmax (3) Load and line regulation are specified at constant junction tempereture. Changes in Vo due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. (4) Selected devices with tightened tolerance reference voltage available. (5) Cadj , when used, connected between the adjustment pin and ground. (6) Since Long - Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average stability from lot to lot. 2 KK317 CHIP PAD DIAGRAM 2.26 ±0.03 01 06 2.1± 0.03 04 05 03 02 (0,0) Thickness of chip 0,46±0,02 mm PAD LOCATION Pad No Symbol* output adjust output input input output X 0.070 0.070 1.515 2.010 0.875 1.515 Y 1.800 0.090 0.410 0.935 0.760 1.575 01 02 03 04 05 06 Pad size** , mm 0.160x0.195 0.180x0.185 0.190x0.170 0.180x0.205 0.165x0.175 0.190x0.170 * Pads 01, 03, 06 connected in the chip. Pads 04, 05 connected in the chip. ** Pad size is given as per metallization layer 3 KK317 TO-220 4