KK311

TECHNICAL DATA High Performance Voltage Comparators KK311 LOGIC DIAGRAM Input polarity is reversed when GND pin is used as an output. ORDERING INFORMATION KK311N Plastic KK311D SOIC TA = -45°C to 85°C for all packages PIN ASSIGNMENT MAXIMUM RATINGS Symbol VCC + ⏐VEE⏐ VO - VEE VEE VID VIN PD 1/θJA TJ(max) Tstg Parameter Total Supply Voltage Output to Negative Supply Voltage Ground to Negative Supply Voltage Input Differential Voltage Input Voltage (Note) Voltage at Strobe Pin Power Dissipation and Thermal Characteristics Plastic Dual In-Line Packages Derate above TA =+25°C Operating Junction Temperature Storage Temperature Range Value 36 40 30 ± 30 ± 15 VCC to VCC - 5 625 5.0 +150 -60 to +150 Unit V V V V V V mW mW/°C °C °C Note: This rating applies for ±15 volt supplies. The positive input voltage limit is 30 volts above the negative supply. The negative input voltage limit is equal to the negative supply voltage or 30 volts below the positive supply, whichever is less. 1 KK311 RECOMMENDED OPERATING CONDITIONS Symbol VCC + ⏐VEE⏐ TA Total Supply Voltage Operating Temperature, All Package Types - 45 Parameter Min Max 30 +85 Unit V °C ELECTRICAL CHARACTERISTICS (VCC=+15 V, VEE= -15 V, TA =+25°C unless otherwise noted [Note 1]) Symbol VIO IIO IIB Parameter Input Offset Voltage (Note 2) Input Offset Current (Note 2) Input Bias Current Test Conditions RS ≤ 50 kΩ, TA = +25°C RS ≤ 50 kΩ, -45°C ≤ TA ≤ 85°C TA = +25°C -45°C ≤ TA ≤ 85°C TA = +25°C TA = -45°C TA = +85°C 150000 300 TA = +25°C VID ≤ -10 mV, IO=50 mA -14.5 1.5 13.0 +7.5 -5.0 ns V V mA mA Guaranteed Limits Min Max 7.5 10 50 100 250 375 500 mV nA nA Unit AV tDLH VDS VIR ICC IEE Voltage Gain Propagation Delay Time Saturation Voltage Input Voltage Range Positive Supply Current Negative Supply Current NOTES: 1. Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 volt supply up to ±15 volt supplies. 2. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA load. Thus, these parameters define an error band and take into account the “worst case” effects of voltage gain and input impedance. 2 KK311 N S UFFIX PLAS TIC DIP (MS – 0 0 1BA) A 8 5 B 1 4 Dimens ion, mm Symbol A B MIN 8.51 6.1 MAX 10.16 7.11 5.33 0.36 1.14 2.54 7.62 0° 2.92 7.62 0.2 0.38 10° 3.81 8.26 0.36 0.56 1.78 F L C D C -T- SEATING PL AN E F G M H J N G D 0.25 (0.010) M T K H J K L M N NOTES : 1. Dimen s io n s “A ”, “B” d o n o t in clu d e mo ld flas h o r p ro tru s io n s . Maximu m mo ld flas h o r p ro tru s io n s 0.25 mm (0.010) p er s id e. D S UFFIX S OIC (MS - 0 1 2 AA) Dimens ion, mm 5 A 8 Symbol A B P MIN 4.8 3.8 1.35 0.33 0.4 1.27 5.72 0° 0.1 0.19 5.8 0.25 MAX 5 4 1.75 0.51 1.27 H B C 1 G 4 C R x 45 D F -TD 0.25 (0.010) M T C M K SEATI NG PLAN E G J F M H J K M P R 8° 0.25 0.25 6.2 0.5 NOTES : 1. Dimen s io ns A an d B d o n o t in clud e mo ld flas h o r p rotru s ion . 2. M aximu m mo ld flas h o r p ro tru s io n 0.15 mm (0.006) p er s id e fo r A ; fo r B ‑ 0.25 mm (0.010) p er s id e. 3