KK4006B

TECHNICAL DATA KK4006B СMOS 18-Stage Static Shift Register The RCA-4006B types are composed of 4 separate shift register sections: two sections of four stages and two sections of five stages with an output tar at the fourth stage. Each section has an independent single-rail data path. • • • • Standardized, symmetriсal output characteristics Operating Voltage Range: 3.0 to 18 V 100% tested for guiescent current at 20 V Maximum input current of 1 µA at 18 V over full package-temperature range; 100 nA at 18 V and 25°C • Noise margin ( full package temperature range): 1.0 V at VDD=5.0 V 2.0 V at VDD =10.0 V 2.5 V at VDD =15.0 V N SUFFIX PL AST IC 14 1 14 D SUFFIX S O IC 1 ORDERING INFORMATION KK4006BN Plastic KK4006BD SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT D1 01 14 TERMINAL ASSIGNMENT Pin.No 01 02 03 04 05 06 07 08 09 10 11 VDD D1+4 D2+5 D2+4 D3+4 Symbol D1 D1+4/ C D2 D3 D4 VSS D4+4 D4+5 D3+4 D2+4 D2+5 D1+4 D1+4' 02 C 03 13 12 D2 04 4006 11 D3 05 10 D4 06 09 D4+5 V SS 07 08 D4+4 FUNCTION TABLE Inputs C D1 L H X L H X Outputs D1+4 / D2-D4 D1+4...D4+4 L H X X X X 12 13 14 L H Storage Storage Storage D1...D4 Storage Storage D1 L H Storage Description Input Data Output Data Clock Data Input Data Input Data Input Data Ground Output Data Output Data Output Data Output Data Output Data Output Data Positive Pover Supply VDD X = don’t care 1 KK4006B MAXIMUM RATINGS* Symbol VDD VIN IIN PD Ptot Tstg TL * Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Input Current, per Pin Power Dissipation in Still Air, Plastic DIP, SOIC Package Power Dissipation per Output Transistor Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) Value -0.5 to +20 -0.5 to VDD +0.5 ±10 500** 100 -65 to +150 260 Unit V V mA mW mW °C °C Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. **Derating: - Plastic DIP from -55 to +100°C - SOIC Package from -55 to +65°C - Plastic DIP: - 12 mW/°C from +100 to +125°C - SOIC Package: : - 7 mW/°C from +65 to +125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN TA Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) Operating Temperature, All Package Types Min 3.0 0 -55 Max 18 VCC +125 Unit V V °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation VIN should be constrained to the range GND≤VIN ≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either Vss or VDD). Unused outputs must be left open. 2 KK4006B DC ELECTRICAL CHARACTERISTICS Symbol Parameter Test Conditions VDD, V 55 ° C min VIH Minimum HighVO = 0.5 V or VDD-0.5 V Level Input Voltage VO = 1.0 V or VDD-1.0 V VO = 1.5 V or VDD-1.5 V VIL Maximum Low VO = 0.5 V or VDD-0.5 V Level Input Voltage VO = 1.0 V or VDD-1.0 V VO = 1.5 V or VDD-1.5 V VOH Minimum HighLevel Output Voltage Maximum LowLevel Output Voltage Maximum Input Current Maximum Input Leakage Current Maximum Quiescent Supply Current (per Package) VI = VSS или VDD 5.0 10 15 5.0 10 15 3.5 7.0 11 max 1.5 3.0 4.0 0.05 0.05 0.05 -0.1 +0.1 5.0 10.0 20.0 100 Guaranteed Limit 125° C min 3.5 7.0 11 4.95 9.95 14.95 0.36 0.9 2.4 -1.15 -0.36 -0.9 -2.4 max 1.5 3.0 4.0 0.05 0.05 0.05 -1.0 +1.0 150 300 600 3000 25° C min 3.5 7.0 11 4.95 9.95 14.95 0.51 1.3 3.4 -1.6 -0.51 -1.3 -3.4 max 1.5 3.0 4.0 0.05 0.05 0.05 -0.1 +0.1 5.0 10 20 100 mA 5.0 -2.0 5.0 -0.64 10 -1.6 15 -4.2 7.5 pF V V V Unit 5.0 4.95 10 9.95 15 14.95 5.0 10 15 18 18 5.0 10 15 20 5.0 10 15 0.64 1.6 4.2 VOL VI = VSS или VDD V IIL IIH IDD VI = VSS VI = VDD VI = VSS or VDD µA µA µA IOL Minimum Output VI = VSS or VDD Low (Sink) Current VOL = 0.4 V VOL = 0.5 V VOL = 1.5 V Minimum Output High (Source) Current VI = VSS or VDD VOH = 2.5 V VOH = 4.6 V VOH = 9.5 V VOH = 13.5 V mA IOH CIN Maximum Input Capacitance 3 KK4006B TIMING REQUIREMENTS (CL=50 пФ, RL = 200 кОм, tLH = tHL ≤ 20 нс) Symbol Parameter UDD, V 55 ° C min max tPHL, tPLH tTHL, tTLH tSU Propagation Delay Time Transition Time 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 400 200 160 200 100 80 125° C min max 800 400 320 400 200 160 25° C min max 400 200 160 200 100 80 ns ns Guaranteed Limit Unit Minimum Data Setup Time Minimum Hold Time, Clock to Data Minimum Clock Pulse Width Maximum Clock Input Freguency Maximum Clock Input Rise or Fall Time 100 50 40 150 80 60 200 90 60 200 100 80 300 160 120 400 180 120 100 50 40 150 80 60 200 90 60 ns tH - - - ns tW - - - nc fC 2.5 5.0 7.0 15 15 15 1.25 2.5 3.5 15 15 15 2.5 5.0 7.0 15 15 15 MHz tr(CL) tf(CL) µs 4 KK006B LOGIS DIAGRAM WITH DETAIL OF LATCH D1 (01) CLOCK (03) D2 (04) D CC Q D CC Q D C C Q D CC Q D 1+4 Q CC D1+4 (13) D1+4 (02) D2+4 (11) D C C Q D CC Q D C C Q D CC Q D CC Q D2+5 (12) D3 (05) D CC Q D CC Q D CC Q D C C Q D3+4 (10) D4+4 (08) D4+5 (09) D4 (06) D Q CC D CC Q D C C Q D CC Q D CC Q 5 KK4006B tLH D1,D2, D3,D4 0.1 tSU tLH CLK 0.1 0.9 0.5 tHL UDD 0.5 0.5 0.5 0.5 0В 0.9 0.5 tHL UDD tH 0В 1 tWH 4 tPLH 5 8 tPHL 9 D1+4,D2+4, D3+4,D4+4 0.9 0.5 0.1 0.9 0.5 0.1 UOH tTLH tPLH D1+4/ 0.9 0.5 0.1 tTHL tPHL 0.9 0.5 0.1 UOL UOH tTLH tPLH D2+5,D4+5 0.9 0.5 0.1 tTHL tPHL 0.9 0.5 UOL UOH 0.1 UOL tTLH tTHL SWITCHING WAVEFORMS 6 KK4006B N SUFFIX PLASTIC DIP (MS - 001AA) A 14 8 B 1 7 Dimensions, mm Symbol A B MIN 18.67 6.10 0.36 1.14 2.54 7.62 0° 2.92 7.62 0.20 0.38 10° 3.81 8.26 0.36 MAX 19.69 7.11 5.33 0.56 1.78 F L C D F G J C -T- SEATING N G D 0.25 (0.010) M T K PLAN E M H H J K L M N NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D SUFFIX SOIC (MS - 012AB) A 14 8 Dimensions, mm H B P Symbol. A B C C R x 45 MIN 8.55 3.80 1.35 0.33 0.40 1.27 5.72 0° 0.10 0.19 5.80 0.25 MAX 8.75 4.00 1.75 0.51 1.27 1 G 7 D F G -TD 0.25 (0.010) M T C M K SE ATING PL AN E J F M H J K M P R 8° 0.25 0.25 6.20 0.50 NOTES: 1.Dimensions A and B do not include mold flash or protrusion. 2.Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B - 0.25 mm (0.010) per side. 7