KK4580D

TECHNICAL DATA DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The KK4580 is the dual operational amplifier, specially designer for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, and it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools. It is also suitable for the head phone amp at higher output current, and further more, it can be applied for the handy type set operational amplifier of general purpose in application of low voltage single supply type which is properly biased of the input low voltage source. FEATURES • Operating Voltage • Slew Rate • Bipolar Technology (±2 V ∼ ±18 V) (5 V/µs typ.) • Wide Gain Bandwidth Product (15 MHz typ.) KK4580 ORDERING INFORMATION KK4580N Plastic KK4580D SOIC TA = -40° to 85° C for all packages. BLOCK DIAGRAM A -INPUT A +INPUT 2 3 + 1 A OUTPUT PIN ASSIGNMENT B -INPUT B +INPUT 6 5 + 7 B OUTPUT EQUIVALENT CIRCUIT (1/2 Show) V+ -INPUT +INPUT Output V 1 KK4580 ABSOLUTE MAXIMUM RATINGS (Ta=25°C) Symbol V /V VID VIC IO Topr Tstg * + - Parameter Supply Voltage Differential Input Voltage Input Voltage Output Current Operation Temperature Range Storage Temperature Range Ratings ±18 30 ±15* ±50 -40 ∼ +85 -60 ∼ +125 Unit V V V mA °C °C For supply voltage less then ±15 V, the absolute maximum input voltage is equal to the supply voltage. ELECTRICAL CHARACTERISTICS (Ta=25°C, V+/V- = ±15) Symbol VIO IIO IB RIN AV VOM VICM CMR SVR ICC SR Parameter Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Large Signal Voltage Gain Output Voltage Swing Input Common Mode Voltage Range Common Mode Rejection Ratio Supply Voltage Rejection Ratio Operating Current Slew Rate RL ≥ 2 kΩ RS ≤ 10 kΩ RS ≤ 10 kΩ RL ≥ 2 kΩ, VO = ±10 V RL ≥ 2 kΩ Test Condition RS ≤ 10 kΩ Min 0.3 90 ±12 ±12 80 80 4 Max 3 200 500 9 6 Unit mV nA nA MΩ dB V V dB dB mA V/µs 2 KK4580 3 KK4580 4 KK4580 N S UFFIX PLAS TIC DIP (MS – 0 0 1BA) A 8 5 B 1 4 Dimens ion, mm Symbol A B MIN 8.51 6.1 MAX 10.16 7.11 5.33 0.36 1.14 2.54 7.62 0° 2.92 7.62 0.2 0.38 10° 3.81 8.26 0.36 0.56 1.78 F L C D C -T- SEATING N G D 0.25 (0.010) M T K PL AN E F G M H J H J K L M N NOTES : 1. Dimen s io n s “A ”, “B” d o n o t in clu d e mo ld flas h o r p ro tru s io n s . Maximu m mo ld flas h o r p ro tru s io n s 0.25 mm (0.010) p er s id e. D S UFFIX S OIC (MS - 0 1 2 AA) Dimens ion, mm 5 A 8 Symbol A B P MIN 4.8 3.8 1.35 0.33 0.4 1.27 5.72 0° 0.1 0.19 5.8 0.25 MAX 5 4 1.75 0.51 1.27 H B C 1 G 4 C R x 45 D F -TD 0.25 (0.010) M T C M K SEATI NG PLAN E G J F M H J K M P R 8° 0.25 0.25 6.2 0.5 NOTES : 1. Dimen s io ns A an d B d o n o t in clud e mo ld flas h o r p rotru s ion . 2. M aximu m mo ld flas h o r p ro tru s io n 0.15 mm (0.006) p er s id e fo r A ; fo r B ‑ 0.25 mm (0.010) p er s id e. 5