KK74HC132A

TECHNICAL DATA KK74HC132A Quad 2-Input NAND Gate with Schmitt-Trigger Inputs High-Performance Silicon-Gate CMOS The KK74HC132A is identical in pinout to the LS/ALS132. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. The KK74HC132A can be used to enhance noise immunity or to square up slowly changing waveforms. • Outputs Directly Interface to CMOS, NMOS, and TTL • Operating Voltage Range: 2.0 to 6.0 V • Low Input Current: 1.0 µA • High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION KK74HC132AN Plastic KK74HC132AD SOIC TA = -55° to 125° C for all packages LOGIC DIAGRAM PIN ASSIGNMENT FUNCTION TABLE Inputs A L L H PIN 14 =VCC PIN 7 = GND H B L H L H Output Y H H H L 1 KK74HC132A MAXIMUM RATINGS* Symbol VCC VIN VOUT IIN IOUT ICC PD Tstg TL * Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Output Voltage (Referenced to GND) DC Input Current, per Pin DC Output Current, per Pin DC Supply Current, VCC and GND Pins Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) Value -0.5 to +7.0 -1.5 to VCC +1.5 -0.5 to VCC +0.5 ±20 ±25 ±50 750 500 -65 to +150 260 Unit V V V mA mA mA mW °C °C Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT TA tr, tf * Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) Operating Temperature, All Package Types Input Rise and Fall Time (Figure 1) Min 2.0 0 -55 - Max 6.0 VCC +125 no limit* Unit V V °C ns When VIN ≈ 0.5VCC, ICC> > quiescent current. This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 2 KK74HC132A DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter Test Conditions V Guaranteed Limit 2 5 °C to -55°C 1.5 3.15 4.2 1.0 2.3 3.0 0.9 2.0 2.6 0.3 0.9 1.2 1.2 2.25 3.0 0.2 0.4 0.5 1.9 4.4 5.9 3.98 5.48 0.1 0.1 0.1 0.26 0.26 ±0.1 1.0 ≤85 °C 1.5 3.15 4.2 0.95 2.25 2.95 0.95 2.05 2.65 0.3 0.9 1.2 1.2 2.25 3.0 0.2 0.4 0.5 1.9 4.4 5.9 3.84 5.34 0.1 0.1 0.1 0.33 0.33 ±1.0 10 ≤125 °C 1.5 3.15 4.2 0.95 2.25 2.95 0.95 2.05 2.65 0.3 0.9 1.2 1.2 2.25 3.0 0.2 0.4 0.5 1.9 4.4 5.9 3.7 5.2 0.1 0.1 0.1 0.4 0.4 ±1.0 40 µA µA V Unit VT+max Maximum PositiveGoing Input Threshold Voltage Minimum PositiveGoing Input Threshold Voltage Maximum NegativeGoing Input Threshold Voltage Minimum NegativeGoing Input Threshold Voltage Maximum Hysteresis Voltage Minimum Hysteresis Voltage Minimum HighLevel Output Voltage VOUT=0.1 V ⎢IOUT⎢≤ 20 µA VOUT=0.1 V ⎢IOUT⎢ ≤ 20 µA VOUT=VCC-0.1 V ⎢IOUT⎢≤ 20 µA VOUT=VCC-0.1 V ⎢IOUT⎢ ≤ 20 µA VOUT=0.1 V or VCC-0.1 V ⎢IOUT⎢ ≤ 20 µA VOUT=0.1 V or VCC-0.1 V ⎢IOUT⎢ ≤ 20 µA VIN≤VT-min or VT+max ⎢Iout⎢ ≤ 20 µA VIN≤VT-min or VT+max ⎢IOUT⎢ ≤ 4.0 mA ⎢IOUT⎢ ≤ 5.2 mA 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 6.0 6.0 V VT+min V VT-max V VT-min V VHmax Note VHmin Note VOH V V V VOL Maximum LowLevel Output Voltage VIN ≥VT+max ⎢IOUT⎢ ≤ 20 µA VIN≥ VT+max ⎢IOUT⎢ ≤ 4.0 mA ⎢IOUT⎢ ≤ 5.2 mA IIN ICC Maximum Input Leakage Current Maximum Quiescent Supply Current (per Package) VIN=VCC or GND VIN=VCC or GND IOUT=0µA Note. VHmin>(VT+min)-(VT-max); VHmax=(VT+max)+(VT-min). 3 KK74HC132A AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input tr=tf=6.0 ns) VCC Symbol Parameter V Guaranteed Limit 2 5 °C to -55°C 125 25 21 75 15 13 10 ≤85°C ≤125°C Unit tPLH, tPHL Maximum Propagation Delay, Input A or B to Output Y (Figures 1 and 2) Maximum Output Transition Time, Any Output (Figures 1 and 2) Maximum Input Capacitance Power Dissipation Capacitance (Per Gate) 2.0 4.5 6.0 2.0 4.5 6.0 - 155 31 26 95 19 16 10 190 38 32 110 22 19 10 ns tTLH, tTHL ns CIN pF Typical @25°C,VCC=5.0 V 24 pF CPD Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC Figure 1. Switching Waveforms 4 KK74HC132A N S UFFIX PLAS TIC DIP (MS - 0 0 1 AA) A 14 8 B 1 7 Dimens ion, mm Symbol A B C MIN 18.67 6.1 MAX 19.69 7.11 5.33 0.36 1.14 2.54 7.62 0° 2.92 7.62 0.2 0.38 10° 3.81 8.26 0.36 0.56 1.78 F L D F C -T- SEATING N G D 0.25 (0.010) M T K PLAN E G H H J M J K L M N NOTES : 1. Dimen s io n s “A ”, “B” d o n o t in clu d e mo ld flas h o r p ro tru s io n s . Maximu m mo ld flas h o r p ro tru s io n s 0.25 mm (0.010) p er s id e. D S UFFIX S OIC (MS - 0 1 2 AB) Dimens ion, mm 8 A 14 Symbol A MIN 8.55 3.8 1.35 0.33 0.4 1.27 5.27 0° 0.1 0.19 5.8 0.25 MAX 8.75 4 1.75 0.51 1.27 H B P B C 1 G 7 C R x 45 D F G -TD 0.25 (0.010) M T C M K SEATING PLAN E H J F M J K M P R 8° 0.25 0.25 6.2 0.5 NOTES : 1. Dimen s io ns A an d B d o n o t in clud e mo ld flas h o r p rotru s ion . 2. M aximu m mo ld flas h o r p ro tru s io n 0.15 mm (0.006) p er s id e fo r A ; fo r B ‑ 0.25 mm (0.010) p er s id e. 5