KK74HC139AN

TECHNICAL DATA KK74HC139A Dual 1-of-4 Decoder/Demultiplexer The KK74HC139A is identical in pinout to the LS/ALS139. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. This device consists of two independent 1-of-4 decoders, each of which decodes a two-bit Address to one-of-four active-low outputs. Active-low Selects are provided to facilitate the demultiplexing and cascading functions. The demultiplexing function is accomplished by using the Address inputs to select the desired device output, and utilizing the Select as a data input. • Outputs Directly Interface to CMOS, NMOS, and TTL • Operating Voltage Range: 2.0 to 6.0 V • Low Input Current: 1.0 µA • High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION KK74HC139AN Plastic KK74HC139AD SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs Select PIN 16 =VCC PIN 8 = GND H L L L L A1 X L L H H A0 X L H L H Y0 H L H H H Outputs Y1 H H L H H Y2 H H H L H Y3 H H H H L X = don’t care 1 KK74HC139A MAXIMUM RATINGS* Symbol VCC VIN VOUT IIN IOUT ICC PD Tstg TL * Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Output Voltage (Referenced to GND) DC Input Current, per Pin DC Output Current, per Pin DC Supply Current, VCC and GND Pins Power Dissipation in Still Air, Plastic DIP SOIC Package** Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) ** Value -0.5 to +7.0 -1.5 to VCC +1.5 -0.5 to VCC +0.5 ±20 ±25 ±50 750 500 -65 to +150 260 Unit V V V mA mA mA mW °C °C Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. ** Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT TA tr, tf Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) Operating Temperature, All Package Types Input Rise and Fall Time (Figure 1) VCC =2.0 V VCC =4.5 V VCC =6.0 V Min 2.0 0 -55 0 0 0 Max 6.0 VCC +125 1000 500 400 Unit V V °C ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 2 KK74HC139A DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter Test Conditions V Guaranteed Limit 2 5 °C to -55°C 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 3.98 5.48 0.1 0.1 0.1 0.26 0.26 ±0.1 4.0 ≤85 °C 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 3.84 5.34 0.1 0.1 0.1 0.33 0.33 ±1.0 40 ≤125 °C 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 3.7 5.2 0.1 0.1 0.1 0.4 0.4 ±1.0 160 µA µA V Unit VIH Minimum HighLevel Input Voltage Maximum Low Level Input Voltage Minimum HighLevel Output Voltage VOUT=0.1 V or VCC-0.1 V ⎢IOUT⎢≤ 20 µA VOUT=0.1 V or VCC-0.1 V ⎢IOUT⎢ ≤ 20 µA VIN=VIH or VIL ⎢IOUT⎢ ≤ 20 µA VIN=VIH or VIL ⎢IOUT⎢ ≤ 4.0 mA ⎢IOUT⎢ ≤ 5.2 mA 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 6.0 6.0 V VIL V VOH V VOL Maximum LowLevel Output Voltage VIN=VIH or VIL ⎢IOUT⎢ ≤ 20 µA VIN=VIH or VIL ⎢IOUT⎢ ≤ 4.0 mA ⎢IOUT⎢ ≤ 5.2 mA IIN ICC Maximum Input Leakage Current Maximum Quiescent Supply Current (per Package) VIN=VCC or GND VIN=VCC or GND IOUT=0µA 3 KK74HC139A AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input tr=tf=6.0 ns) VCC Symbol Parameter V Guaranteed Limit 2 5 °C to -55°C 115 23 20 115 23 20 75 15 13 10 ≤85°C ≤125°C Unit tPLH, tPHL Maximum Propagation Delay, Select to OutputY (Figures 1 and 3) Maximum Propagation Delay , Input A to OutputY (Figures 2 and 3) Maximum Output Transition Time, Any Output (Figures 1 and 3) Maximum Input Capacitance Power Dissipation Capacitance (Per Decoder) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 - 145 29 25 145 29 25 95 19 16 10 175 35 30 175 35 30 110 22 19 10 ns tPLH, tPHL ns tTLH, tTHL ns CIN pF Typical @25°C,VCC=5.0 V 55 pF CPD Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC Figure 1. Switching Waveforms Figure 2. Switching Waveforms 4 KK74HC139A Figure 3. Test Circuit EXPANDED LOGIC DIAGRAM (1/2 of Device) 5 KK74HC139A N S UFFIX PLAS TIC DIP (MS - 0 0 1 BB) A Dimens ion, mm 16 9 B Symbol A MIN 18.67 6.1 MAX 19.69 7.11 5.33 1 8 B C F L D F 0.36 1.14 2.54 7.62 0° 2.92 7.62 0.2 0.38 0.56 1.78 C -T- SEATING PLAN E G H H J N G D 0.25 (0.010) M T K M J K L M N 10° 3.81 8.26 0.36 NOTES : 1. Dimen s io n s “A ”, “B” d o n o t in clu d e mo ld flas h o r p ro tru s io n s . Maximu m mo ld flas h o r p ro tru s io n s 0.25 mm (0.010) p er s id e. D S UFFIX S OIC (MS - 0 1 2 AC) Dimens ion, mm A 16 9 Symbol A MIN 9.8 3.8 1.35 0.33 0.4 1.27 5.72 0° 0.1 0.19 5.8 0.25 MAX 10 4 1.75 0.51 1.27 H B P B C 1 G 8 C R x 45 D F G -TD 0.25 (0.010) M T C M K SEAT ING PLAN E J F M H J K M P R 8° 0.25 0.25 6.2 0.5 NOTES : 1. Dimen s io ns A an d B d o n o t in clud e mo ld flas h o r p rotru s ion . 2. M aximu m mo ld flas h o r p ro tru s io n 0.15 mm (0.006) p er s id e fo r A ; fo r B ‑ 0.25 mm (0.010) p er s id e. 6