KK74HC153A

TECHNICAL DATA KK74HC153A Dual 4-Input Data Selector/Multiplexer High-Performance Silicon-Gate CMOS The KK74HC153A is identical in pinout to the LS/ALS153. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. The Address Inputs select one of four Data Inputs from each multiplexer. Each multiplexer has an active-low Strobe control and a noninverting output. • Outputs Directly Interface to CMOS, NMOS, and TTL • Operating Voltage Range: 2.0 to 6.0 V • Low Input Current: 1.0 µA • High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION KK74HC153AN Plastic KK74HC153AD SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs A1 X L L PIN 16 =VCC PIN 8 = GND H H A0 X L H L H Strobe H L L L L Output Y L D0 D1 D2 D3 D0,D1...D3=the level of the respective Data Input X = don’t care 1 KK74HC153A MAXIMUM RATINGS* Symbol VCC VIN VOUT IIN IOUT ICC PD Tstg TL * Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Output Voltage (Referenced to GND) DC Input Current, per Pin DC Output Current, per Pin DC Supply Current, VCC and GND Pins Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) Value -0.5 to +7.0 -1.5 to VCC +1.5 -0.5 to VCC +0.5 ±20 ±25 ±50 750 500 -65 to +150 260 Unit V V V mA mA mA mW °C °C Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT TA tr, tf Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) Operating Temperature, All Package Types Input Rise and Fall Time (Figure 1) VCC =2.0 V VCC =4.5 V VCC =6.0 V Min 2.0 0 -55 0 0 0 Max 6.0 VCC +125 1000 500 400 Unit V V °C ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 2 KK74HC153A EXPANDED LOGIC DIAGRAM 5 KK74HC153A DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter Test Conditions V Guaranteed Limit 2 5 °C to -55°C 1.5 3.15 4.2 0.3 0.9 1.2 1.9 4.4 5.9 3.98 5.48 0.1 0.1 0.1 0.26 0.26 ±0.1 8.0 ≤85 °C 1.5 3.15 4.2 0.3 0.9 1.2 1.9 4.4 5.9 3.84 5.34 0.1 0.1 0.1 0.33 0.33 ±1.0 80 ≤125 °C 1.5 3.15 4.2 0.3 0.9 1.2 1.9 4.4 5.9 3.7 5.2 0.1 0.1 0.1 0.4 0.4 ±1.0 160 µA µA V Unit VIH Minimum HighLevel Input Voltage Maximum Low Level Input Voltage Minimum HighLevel Output Voltage VOUT=0.1 V or VCC-0.1 V ⎢IOUT⎢≤ 20 µA VOUT=0.1 V or VCC-0.1 V ⎢IOUT⎢ ≤ 20 µA VIN=VIH or VIL ⎢IOUT⎢ ≤ 20 µA VIN=VIH or VIL ⎢IOUT⎢ ≤ 4.0 mA ⎢IOUT⎢ ≤ 5.2 mA 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 6.0 6.0 V VIL V VOH V VOL Maximum LowLevel Output Voltage VIN=VIH or VIL ⎢IOUT⎢ ≤ 20 µA VIN=VIH or VIL ⎢IOUT⎢ ≤ 4.0 mA ⎢IOUT⎢ ≤ 5.2 mA IIN ICC Maximum Input Leakage Current Maximum Quiescent Supply Current (per Package) VIN=VCC or GND VIN=VCC or GND IOUT=0µA 3 KK74HC153A EXPANDED LOGIC DIAGRAM 5 KK74HC153A AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input tr=tf=6.0 ns) VCC Symbol Parameter V Guaranteed Limit 2 5 °C to -55°C 140 28 24 175 35 30 95 19 16 75 15 13 10 ≤85°C ≤125°C Unit tPLH, tPHL Maximum Propagation Delay, Input D to Output Y (Figures 1 and 4) Maximum Propagation Delay , Input A to Output Y (Figures 2 and 4) Maximum Propagation Delay , Strobe to Output Y (Figures 3 and 4) Maximum Output Transition Time, Any Output (Figures 1 and 4) Maximum Input Capacitance Power Dissipation Capacitance (Per Muliplexer) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 - 175 35 30 220 44 37 120 24 20 95 19 16 10 210 42 36 265 53 45 145 29 25 110 22 19 10 ns tPLH, tPHL ns tPLH, tPHL ns tTLH, tTHL ns CIN pF Typical @25°C,VCC=5.0 V 31 pF CPD Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC Figure 1. Switching Waveforms Figure 2. Switching Waveforms Figure 3. Switching Waveforms Figure 4. Test Circuit 4