KRM-HR1116

Parts No: KRM-HR1116 SPECIFICATION FOR APPROVAL ISSUED DATE : DOCUMENT NO : 2-Sep-20 OQSS-R903V1-7U-01 CUSTOMER : Haier Air-con DESCRIPTION : IR RECEIVER MODULE MODEL NO. : KRM-HR1116 [ AUK Corp. ] ISSUE DEPT. PRODUCTION Q/A ISSUE REVIEW APPR'L REVIEW APPR'L REVIEW APPR'L [ CUSTOMER APPROVAL ] ISSUE REVIEW [ REVISION ] NO 0 AUK-QM-043-1(C) DATE 2020-09-02 REVISION ITEMS ISSUE 1/9 ISSUED BY TY.KIM APPR'D BY YJ.JIN Parts No : KRM-HR1116 This specification sheets include the contents under the copyright of AUK Corp. ("KODENSHI"). Please keep them with reasonable care as important information. Please don't reproduce or cause anyone reproduce them without KODENSHI's consent. KODENSHI takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet. Please obey the instructions mentioned below for actual use of this device. ① This device is designed for general electronic equipment. Main use of this device are as follows; * Computer * OA equipment * Telecommunication equipmet(Terminal) * Measuring instrument * Machine tool *Industrial robot * AV equipment * Home appliance,etc. ② Please take proper steps in order to maintain reliability and safety, in case this device is used for the uses mentioned below which require high reliability. * Unit concerning control and safety of a vehicle (air plane,train,automobile etc.) * Traffic signal * Gas leak detection breaker * Fire box and burglar alarm box * Other safety equipment,etc. ③ Please don't use for the uses mentioned below which require extremely high reliability. * Space equipment * Telecommunication equipment(Trunk) * Nuclear control equipment * Medical equipment(relating to any fatal element),etc. AUK-QM-043-2(C) 2/9 Parts No : KRM-HR1116 1. Description The KRM-HR1116 consist of a PIN Photodiode of high speed and a preamplifier IC in the package as an receiver for Infrared remote control systems. 2. Features ◆ 2.7 ~ 5.5 Volt supply voltage, low power consumption ◆ Shielded against electrical field disturbance ◆ High immunity against ambient light ◆ Easy interface with the main board ◆ TTL and CMOS compatibility 1. OUT 2. GND 3.VCC ◆ One mold package ◆ RoHS Compliance 3. Applications ◆ TV, VTR, Audio, Air Conditioners, Car Stereo Units, Computers, Interior controlling appliances, and appliances that require remote controlling. 4. Package Outlines See the attached Drawing No. RM-R90□V1-ASY-01 5. Absolute Maximum Ratings Parameter Symbol Rating Unit Supply Voltage / Output Voltage Vcc 6 V Supply Current / Output Current Iout 5.0 ㎃ Operating Temperature Topr. -20℃∼80℃ ℃ Storage Temperature Tstg. -25℃∼85℃ ℃ Soldering Temperature Tsol. 260(Max 5 sec) ℃ [Ta = 25℃ ] 6. Reliability Test Parameter Rating High Temperature *1 Ta=＋80℃, Vcc=5V t=240H High Temperature / High Humidity *1 Ta=＋85℃, 85％RH, Vcc=5V t=240H Low Temperature *1 Ta=－30℃, Vcc=5V t=240H -25℃(0.5H) ∼＋85℃(0.5H) 20cycle Heat Cycle *1 Test devices shall be dropped 3 time naturally onto Dropping *2 Note : hard wooden board from a 75㎝ height position *1. Electro-optical Characteristics shall be satisfied after leaving 2hours in the normal temperature *2. Electro-optical Characteristics shall be satisfied and no deforms and destructions of appearance. (excepting deforms of terminals) AUK-QM-043-2(C) 3/9 Parts No : KRM-HR1116 7. Electro-optical Characteristics Symbol Parameter [ Ta= 25℃, Vcc=5.0V ] Conditions Vcc Supply Voltage Range Vcc=5V No Input Signal Min. Typ. Max. Unit 2.7 - 5.5 V 0.8 ㎃ 0.45 Current Consumption Icc Peak Wavelength *3 λp - 940 - ㎚ B.P.F Center Frequency *4 fo - 37.9 - ㎑ Arrival Distance *3 L 0˚ 32 - - m ±30 ˚ 24 - - m - V Vcc=3V 200Lux High Level Output Voltage *3 VOH Low Level Output Voltage *3 VOL 30cm over the ray axis High Level Output Pulse Width *3 TWH Low Level Output Pulse Width *3 TWL 0.40 Vcc-0.5 Vcc-0.3 - 0.2 0.5 V Burst Wave = 600㎲ 400 - 800 ㎲ Period = 1.2㎳ 400 - 800 ㎲ Output Form Note : 0.2 Active Low Output *3. It specifies the maximum distance between emitter and detector that the output waveform satisfies the standard(8-2,3) under the conditions below against the standard transmitter 1) Measuring place : Indoor without extreme reflection of light 2) Ambient light source : Detecting surface illumination shall be irradiate 200±50Lux under ordinary white fluorescence lamp without high frequency lightning 3) Standard transmitter : Burst wave indicated in drawing(8-1) of standard transmitter shall be arranged to 1.6Vp-p under the measuring circuit specified in drawing(8-2,3) : 4) Application Circuit Recommend to design a circuit without using Rp & Cp2. Rs Transmitter Receiver Module Vcc Vcc Cp1 Rp Micom Vout Cp2 GND GND : Typ. 100Ω (47Ω ~ 470Ω) ■ Rs (Vcc input series resistor) ■ Cp1(Vcc-GND terminal series Condenser) : Typ. 100㎌ (4.7㎌ ~ 470㎌) ■ Rp (Vcc-Vout terminal Pullup resistor) : Optional (when using 1㏀ or more ) When Rp is lower than 1㏀, Micom can't reply by a VoL rise. ■ Cp2(Vout-GND terminal pararllel Condenser) AUK-QM-043-2(C) : Optional (when using 1㎋~2㎋) 4/9 Parts No : KRM-HR1116 8. Measure Method 8-1. Output Pulse Width Transmitter output Carrier Frequency(fo) Duty50% 600us 600us Remocon output pulse T WL T WH VOH VOL 8-2. Standard Transmitter 10㏀ +5V Standard Transmitter 10㏀ 10㎌ Vout 25Cm 8-3. Test Condition of Transmission Distance Vout Standard Transmitter θ θ OSC GND Transmission Distance : L VCC θ AUK-QM-043-2(C) 5/9 : Indicates horizontal and vertical directions Parts No : KRM-HR1116 9. Inspection Criteria In electro-optical characteristics, total quantity shall be inspected as below. - Front distance between emitter and detector - Current consumption - High level output voltage - Low level output voltage 10. Customer must check below clauses before using 10-1. When this infrared remote control detecting unit shall be adopted for wireless remote control, please keep the following standards. Suitable data format : ● Not recommend data format : x 1) Data word length = Max. 100msec NEC CODE ● SONY 12bit 2) tpause = Min. 25msec RC5 / RC6 ● SONY 15bit ● Matsushita Code ● × Mitsubishi Code × Toshiba Micom Code ● SONY 20bit × Zenith Code ● 4) tBurst = Min. 300usec Sharp Code ● RCMM × JVC Code ● 5) tGap = Min. 350usec Continuous Data communication don't support. (tpause = 0ms) 3) Duty(Σtburst /T ) = Max. 30% 6) above (1)~(5) should be all meet and all remote control button should be operated properly. 10-2. We recommand minimum 30cm distance between RC-M and transmitter for normal operating. If the distance between RC-M and Transmitter is too near, it might not respond. 10-3. If your condition doesn't meet the above statement, it might not operate properly. 11. Caution(When use and storage of this device) 11-1. Store and use where there is no force causing transformation or change in quality 11-2. Store and use when there is no extreme humidity 11-3. Do not wash this device. Wipe the stains of diode side with a soft cloth. You can use the solvent, ethylalcohol or methylalcohol or isopropylalcohol only. 11-4. The shield case shall be grounded on the PCB pattern. There are two cases, one is that shield case and GND pin are connected in the shiled case, the other is not connected in it. If the receiver modules of shield case is not becoming ground connection, there is a possibility of being weak in the EMI(ElectroMagnetic interference) condition. 11-5. Solder pad within the condition of ratings. after soldering do not add extrorse force. AUK-QM-043-2(C) 6/9 Parts No : KRM-HR1116 11-6. Solder pad within the condition of ratings. after soldering do not add extrorse force. 11-7. Put decoupling device between Vcc and GND for reduce the noise from power supply line. recommand Vcc-GND 47㎌ and Vcc- 100Ω. Decoupling device should be near receiver modules. 11-8. The decrease in distance, the output noise, the malfunction, etc. might occur because of a surrounding electromagnetic environment. 11-9. To prevent static electricity damage to the Pre-AMP make sure that the human body, the soldering iron is connected to ground before using 11-10. This device has to control of static electricity AUK Corp. guarantees a R SOURCE C KRM-HR1116 up to M.M 200V , HBM 2KV M.M = MACHINE MODEL(Resistance: 0KΩ Capacitor: 200pF) HBM = HUMAN BODY MODEL( Resistance: 1.5kΩ Capacitor: 100pF) Receiver Modules 11-11. This device is not design to endure radiate rays and heavily charged particles. 12. Period of Guarantee and Extent of Guarantee 12-1. Period of Guarantee 1 year after designated place. 12-2. Extent of Guarantee AUK Corp. Shall supply the replacements against defects that will caused from KODENSHI AUK Corp. fault. 12-3. This product complies with RoHS directive. Object : mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated diphenyl others 13. Manual Soldering 13-1. Use a soldering iron of 25W or less. Adjust the temperature of the soldering iron below 350℃. 13-2. Finish sodering within three seconds. 13-3. Handle products only after the temperature has cooled off. 13-4. To avoid the product is transformed and breakdown, it needs to take care that the power should not join to the product at soldering or immediately after soldering. AUK-QM-043-2(C) 7/9 Parts No : KRM-HR1116 14. DIMENSION 14-1. DIMENSION Point "A" : Max. thickness 0.7mm Point "B" : Max. thickness 0.5mm Drawing No : RM-R90□V1-ASY-01 - Pin configuration ① Vout ② GND ③ Vcc AUK-QM-043-2(C) 1. Unit : mm 2. Unspecified tolerance : ± 0.3mm 3. Lead edge finish : Solder dip 8/9 Parts No : KRM-HR1116 15. PACKING Anti-Electrostatic Poly bag x 10(Max) ( 1000pcs ) Label A ① Anti-Electrostatic Poly bag(Max) ( 100pcs ) Label B ② Inner Box ③ Out Box Inner Box x 10(Max) ( 10,000pcs ) Label xxxx-xxxxxxDG92xxxx-xxxxxxxxxxxx PART NO : xxxx-xxxxxx SPECIFICATION : R.MODULE[XX] LOT NO : xxxx-xxxx QTY : 10000 VENDOR P/N : KRM-HR1116 VENDOR/CODE : XXX / XXXX 20xx-xx-xx Poly bag Inner Box Out Box AUK-QM-043-2(C) 9/9 Dimension(㎜) Quantity(pcs) 235×130×110 575×285×265 100 1,000 10,000