KSM-911SY1E

Optic receiver module KSM-91□SY1E The KSM-91□SY1E consist of a PIN Photodiode of high speed and a preamplifier IC in the package as an receiver for Infrared remote control systems DIMENSIONS Features ㆍWide angle design ㆍWide supply-voltage range : 2.7V to 5.5V ㆍShielded against electrical field disturbance ㆍHigh immunity against ambient light disturbances (Logic Controller Adaptation) ㆍAvailable for carrier frequencies between 32.7KHz to 56.9KHz ㆍTTL and CMOS compatible Applications ㆍAudio & Video Applications (TV, VTR, Audio, DVDP, CDP) ㆍHome Appliances (Air conditioner, Computer, Camcoder) ㆍWireless Toys ㆍRemote Control Equipment Maximum Ratings Parameter Supply Voltage Operating Temperature Storage Temperature Soldering Temperature Symbol Vcc Topr Tstg Tsol Ratings 6.0 -10 ~ +60 -20 ~ +75 260 (Max 5 sec) [Ta=25℃] Unit V ℃ ℃ ℃ B.P.F Center Frequency Model No. KSM-911SY1E KSM-912SY1E KSM-913SY1E KSM-914SY1E KSM-915SY1E B.P.F Center Frequency(㎑) 40.0 36.7 37.9 32.7 56.9 [Ta=25℃, Vcc=5.0V(Vcc=3.0V)] Typ. Max. Unit 5.5 V 1.2(1.0) 1.7 ㎃ 940 ㎚ 37.9 ㎑ m 5.0(3.0) V 0.1 600 0.5 700 700 V ㎲ ㎲ Electro-Optical Characteristics Parameter Recommended Supply Voltage Current Consumption Peak Wavelength *1 B.P.F Center Frequency Transmission Distance High level Output voltage Low level Output voltage *1 *1 *1 Symbol Vcc Icc λp fo L VOH VOL TWH TWL Condition No signal input Min. 2.7 0.5 15 12 4.5(2.8) 500 250±50lx 30cm over the ray axis 0˚ ±30˚ High level Output Pulse Width *1 Low level Output Pulse Width *1 Output Form Burst wave=600㎲ Period = 1.2㎳ 500 600 Active Low Output *1. It specifies the maxmum distance between emitter and detector that the output wave form satisfies the standard under the conditions below against the standard transmitter. 1) Measuring place : Indoor without extreme reflection of light high frequency lightning 3) Standard transmitter : Burst wave of standard transmitter shall be arranged to 50mVP-P under the measuring circuit 2) Ambient light source : Detecting surface illumination shall be irradiate 200±50lx under ordinary white fluorescence lamp without 1/2 Optic receiver module KSM-91□ SY1E ■ Measuring Method [Ta=25℃] Output Pulse Width Transmitter output Carrier Frequency(fo) Duty50% Remocon output pulse Standard Transmitter Test Method of Transmission Distance +5V 600us 600us Standard Tansmitter 10㏀ Vout Transmitter 10㏀ 10㎌ Vout Arrival Distance : L OSC Vcc GND : Indicates horizontal and vertical directions T WL VH THL 25Cm VL ■ Typical Characteristics Curve [Ta=25℃] Relative reception distance Vs. Supply voltage Re lative reception distance 120 ] [% Relative reception distance Vs. Ambient temperature 120 ] [% 100 Radiant pattern 0˚ Relative reception distance 100 80 60 40 20 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 [V] 20 ˚ 40 ˚ -20 ˚ -40 ˚ -60 ˚ 80 60 40 20 60˚ 80˚ 0 100 ˚ 50 100 50 -80 ˚ -100˚ 100 0 -10 0 10 20 30 40 50 [℃] Supply voltage Vcc Ambient temperature Ta Relative Sensitivity (%) ■ Standard Application Circuit with R-C Decoupling Filter R Transmitter Receiver Module Vcc Vout GND *1 Recommended Circuit Description 1) Transmitter(IRED) drive current : IFP = 300mAP-P ~ 600mAP-P 2) R-C Decoupling Filter with Lower Cut-off Frequency : R=100Ω , C=47㎌ : 10kΩ over ⇒ fc = 1/2π RC = 33.9Hz 3) External pull-up resistor(optional) Vcc C Rp micom GND 2/2