S3773P

S377x 7CH Darlin ton TR Sink Driver ng Semiconductor http:// www.auk.co.kr Description The S377x Series are high-voltage, high-current Darlington transistor arrays. Each consists of seven NPN Darlington pairs that feature high-voltage outputs with common-cathode clamp diodes for switching inductive loads. The collector-current rating of a single Darlington pair is 500mA. The Darlington pairs can be paralleled for higher current capability. Applications include relay drivers, SOP-16 hammer drivers, lamp drivers, display drivers (LED and gas discharge), line drivers, and logic buffers. Application ◈ Relay Controller ◈ Lamp and Display LED Driver ◈ Motor Driver DIP-16 Features and Benefits ◈ Output Current (single output) 500mA(Max.) ◈ High sustaining voltage output ORDERING INFORMATION Product S377x S377xP Marking S377x S377xP Package e SOP-20 DIP-18 ◈Output clamp diode ◈ Inputs compatible with various types of logic ◈ Package : SOP-16, DIP-16 ▲ Marking Detail Information Block Diagram & Pin Configuration O1 16 O2 15 O3 14 O4 13 O5 12 O6 11 O7 10 COMMON 9 S377x….[1] YWW….[2] [1] Device Code [ x: Item Code ] [2] Year & Week Code 1 2 3 4 5 6 7 8 I1 I2 I3 I4 I5 I6 I7 GND IX : Input Port GND : Ground OX : Output Port COMMON : Common KSD-I7D002-000 Fab. 2011 REV. 00 1 S377x ◈ Schematics ( Each Driver) COMMON OUTPUT INPUT 10.5kΩ 7.2kΩ COMMON OUTPUT 7.2kΩ 3kΩ GND 3kΩ GND S3771 COMMON OUTPUT INPUT 2.7kΩ 7.2kΩ S3772 COMMON OUTPUT INPUT 10.5kΩ 7.2kΩ 3kΩ GND 3kΩ GND S3773 S3774 ◈ Product Line-up Product Name S3771 S3772 S3773 S3774 S3771P S3772P S3773P S3774P Input Bias Resistor External 7V Zener Diode + 10.5KΩ 2.7KΩ 10.5KΩ External 7V Zener Diode + 10.5KΩ 2.7KΩ 10.5KΩ Designation General Purpose 14~25V PMOS TTL, 5V CMOS 6~15 PMOS, CMOS General Purpose 14~25V PMOS TTL, 5V CMOS 6~15 PMOS, CMOS Operating Temperature -40~85℃ -40~85℃ -40~85℃ -40~85℃ -40~85℃ -40~85℃ -40~85℃ -40~85℃ Package SOP-16 SOP-16 SOP-16 SOP-16 DIP-16 DIP-16 DIP-16 DIP-16 KSD-I7D002-000 Fab. 2011 REV. 00 2 S377x ◈ Absolute Maximum Ratings ( Ta = 25℃ ) Parameter Output Sustaining Voltage Output Current Input Voltage* Input Current** Clamp Diode Reverse Voltage Forward Current Symbol SOP-16 VIN IOUT VIN IIN VR IF IGND Pd TJ Topr Tstg 0.54 Rating DIP-16 -0.5~50 500 -0.5~30 25 50 500 2.8 1.47 150 -40 ~ +85 -55 ~ +150 Unit V mA / ch V mA V mA A W °C °C °C GND Terminal Current Power Dissipation Junction Temperature Operate Temperature Range Storage Temperature Range *( Except S3771/P), **(Only S3771/P) ◈ Recommended Operating Conditions ( Ta=-40~85°C ) Characteristic Output Sustaining Voltage Symbol VCE(SUS) TPW=25ms, DF=10%, 7 Circuits Output Current IOUT TPW=25ms, DF=30%, 7 Circuits Input Voltage Input Current Clamp Diode Reverse Voltage Clamp Diode Forward Current Power Dissipation DIP-16 PD SOP-16 VIN IIN VR IF Except S3771/P Only S3771/P Ta = 85°C Ta = 85°C* 0 0 0 200 30 5 50 400 0.6 W 0.32 V mA V mA Test Condition Min. 0 0 Typ. Max. 50 400 mA Unit V * ( On glass epoxy PCB ( 30 x 30 x 1.6mm Cu50% ) KSD-I7D002-000 Fab. 2011 REV. 00 3 S377x ◈ Electrical characteristics (Ta=-40~85°C; unless otherwise specified ) Characteristic Symbol Test Circuit Test Condition VCE=50V, Ta=25°C Output Leakage Current VCE=50V, Ta=85°C ICEX S3772/P S3774/P 1 VCE=50V, VCE=50V, VIN=6V VIN=1V IIN=500uA IIN=350uA IIN=250uA 50 1000 8 Turn-OFF Delay tOFF VOUT=50V, RL=163Ω, CL=15pF 1.3 1.1 0.9 0.82 0.93 0.35 1.0 65 15 0.1 0.2 500 500 1.6 1.3 1.1 1.25 1.35 mA VIN=5V S3774/P VIN=12V IIN(OFF) S3772/P 4 IOUT=500uA, Ta=85°C VCE=2V, VCE=2V, S3773/P VCE=2V, VCE=2V, Input Voltage VIN(ON) 5 VCE=2V, VCE=2V, S3774/P VCE=2V, VCE=2V, DC Current Transfer Ratio hFE 2 VCE=2V, IOUT=275mA IOUT=350mA IOUT=350mA 7.0 8.0 50 uA 100 2.0 uS V pF IOUT=125mA IOUT=200mA 5.0 6.0 IOUT=300mA IOUT=200mA IOUT=250mA IOUT=300mA 1.45 13 2.4 2.7 3.0 V uA 0.5 V Min. Typ. Max. 50 100 uA Unit IOUT=350mA, Collector – Emitter Saturation Voltage VCE(SAT) 2 IOUT=200mA, IOUT=100mA, S3772/P S3773/P IIN(ON) Input Current 3 VIN=17V VIN=3.85V Clamp Diode Reverse Current IR 6 VR=50V, Ta=25°C VR=50V, Ta=85°C Clamp Diode Forward Voltage Input Capacitance Turn-ON Delay VF CIN tON 7 IF=350mA - KSD-I7D002-000 Fab. 2011 REV. 00 4 S377x Test Circuit 1. ICEX OPEN ICEX VCE OPEN VIN VCE , VCE(sat) IIN 2. VCE(sat) , hFE hFE= IOUT IIN OPEN IOUT 3. IIN(ON) OPEN 4. IIN(OFF) OPEN IOUT IIN(ON) OPEN VIN IIN(OFF) 5. VIN(ON) OPEN IOUT 6. IR IR VR OPEN VIN(ON) VCE OPEN 7. VF VF OPEN IF OPEN KSD-I7D002-000 Fab. 2011 REV. 00 5 S377x 8. tON , tOFF OPEN INPUT RL=163Ω PULSE GENERATOR Note 1 RI Note 2 OUTPUT CL=15pF Note 3 tr 90% INPUT 50% 10% 50us 90% 50% 10% 0 tf VIH VOUT=50V OUTPUT tON tOFF VOH 50% 50% VOL Note 1 : Pulse width 50us, duty cycle 10% Output impedance 50Ω, tr ≤ 5ns, tf ≤ 10ns Note 2 : See below Input Condition Item Code S3771/P S3772/P S3773/P S3774/P Note 3 : CL includes probe and jig capacitance RI 2.7KΩ 0 0 0 VIH 3V 13V 3V 8V Precautions for using This IC does not include built-in protection circuits for excess current or overvoltage. If this IC is subjected to excess current or overvoltage, it may be destroyed. Hence, the utmost care must be taken when systems which incorporate this IC are designed. Utmost care is necessary in the design of the output line, COMMON and GND line since IC may be destroyed due to short−circuit between outputs, air contamination fault, or fault by improper grounding. KSD-I7D002-000 Fab. 2011 REV. 00 6 S377x Application Circuit VSS S3772 V VCC S3773 V 1 16 1 16 2 15 2 15 3 14 3 14 4 13 4 13 5 12 5 12 6 11 6 11 7 10 P-MOS Output TTL Output 7 10 8 9 8 9 Lamp Test P-MOS to Load TTL to Load VDD S3774 V VCC S3773 V 1 16 1 16 2 15 2 15 3 14 3 14 4 13 4 13 RP 5 12 5 12 6 11 6 11 7 10 TTL Output 7 10 C-MOS Output 8 9 8 9 Buffer for Higher Current Loads Use of Pullup Resistors to Increase Drive Current KSD-I7D002-000 Fab. 2011 REV. 00 7 S377x IOUT – Duty Cycle 500 500 IOUT – Duty Cycle Output Current IOUT [mA] n=1 Output Current IOUT [mA] 400 2 300 3 200 S377xP [DIP-16] Ta=25℃ n-ch [ Active ] 0 20 40 60 80 100 4 5 6 7 400 n=1 300 2 200 S377xP [DIP-16] Ta=85℃ Free Air n-ch [ Active ] 0 20 40 60 80 100 3 4 5 6 7 100 100 0 0 Duty Cycle [%] Duty Cycle [%] IOUT – Duty Cycle 500 500 IOUT – Duty Cycle Output Current IOUT [mA] S377x [SOP-16] 400 Ta=85℃ [On PCB] n-ch [ Active ] Output Current IOUT [mA] 400 n=1 300 2 3 4 5 6 7 300 n=1 200 2 3 4 5 6 7 0 20 40 60 80 100 200 100 S377x [SOP-16] Ta=25℃ [On PCB] n-ch [ Active ] 0 20 40 60 80 100 100 0 0 Duty Cycle [%] Duty Cycle [%] IIN – VIN 6.0 3.0 200mA 300mA IOUT=100mA S3771 IIN – VIN Input Current IIN [mA] Input Current IIN [mA] 5.0 4.0 3.0 2.0 1.0 0 0 0.5 1.0 1.5 2.5 2.0 S3772 Ta=25℃ Max. 1.5 Typ. 1.0 0.5 Min. 0 2.0 2.5 3.0 3.5 12 14 16 18 20 22 24 26 Input Voltage VIN [V] Input Voltage VIN [V] KSD-I7D002-000 Fab. 2011 REV. 00 8 S377x IIN – VIN 3.0 3.0 S3773 IIN – VIN Input Current IIN [mA] Input Current IIN [mA] 2.5 2.0 2.5 2.0 1.5 S3774 Max. 1.5 1.0 0.5 Min. 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Typ. Max. 1.0 Typ. 0.5 Min. 0 5 6 7 8 9 10 11 12 Input Voltage VIN [V] Input Voltage VIN [V] IOUT – IIN 500 500 IOUT – VCE(SAT) Output Current IOUT [mA] VCE=2V Output Current IOUT [mA] 400 Ta=25℃ 400 Typ. 300 25℃ Max. 300 200 200 100 100 0 0 100 200 300 400 500 600 0 0 0.5 1.0 1.5 2.0 2.5 3.0 Input Current IIN [uA] VCE(SAT) [V] PD – Ta 1.5 Ta=25℃ IF – V F 500 Forward Current IF [mA] 400 Power Dissipation PD [W] S377xP [DIP16] 1.0 300 200 S377x [SOP16] 0.5 100 0 0 0.4 0.8 1.2 1.6 2.0 2.4 0 0 25 50 75 100 125 150 175 Clamp Diode Forward Voltage VF [V] Ambient Temperature Ta [℃] KSD-I7D002-000 Fab. 2011 REV. 00 9 S377x ◈ SOP-16 Outline Dimension (Unit : mm) ※ Recommend PCB solder land [Unit: mm] KSD-I7D002-000 Fab. 2011 REV. 00 10 S377x ◈ DIP-16(CS) Outline Dimension (Unit : mm) KSD-I7D002-000 Fab. 2011 REV. 00 11 S377x The AUK Corp. products are intended for the use as components in general electronic equipment (Office and communication equipment, measuring equipment, home appliance, etc.). Please make sure that you consult with us before you use these AUK Corp. products in equipments which require high quality and / or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, transportation, combustion control, all types of safety device, etc.). AUK Corp. cannot accept liability to any damage which may occur in case these AUK Corp. products were used in the mentioned equipments without prior consultation with AUK Corp.. Specifications mentioned in this publication are subject to change without notice. 12 KSD-I7D002-000 Fab. 2011 REV. 00