S5225M

S52xxM Low Drop Output Voltage Regulator Description The S52xxM is a u-cap 150mA linear voltage regulator in the SOT-25 package. This regulator has very low dropout voltage and very low ground current. It is designed especially for hand-sets, battery-powered devices and can be controlled by a CMOS or TTL. When the S52xxM is disabled, power consumption drops to nearly zero. Features • Output current of 150mA • Low quiescent current • Low dropout voltage • Current limit protection • Logic-controlled electronic enable Pin Connections 5 4 1 2 PIN Connections 1. Input 2. Ground 3. Control 4. Noise bypass 5. Output 3 Ordering Information Type NO. S52xxM Marking 5□□■ Package Code SOT - 25 □□: Voltage Code (15:1.5V, 18:1.8V, 25:2.5V, 28:2.8V, 30:3.0V, 33:3.3V, 50:5.0V) ■ : YY&WW Code Outline Dimensions (Unit : mm ) BLOCK DIAGRAM VI 1 Bias Circuit 5 Vo Control 3 + Noise 4 Bypass Bandgap Reference - Current Limit Circuit 2 GND KSD-I5O005-003 1 S52xxM Absolute Maximum Ratings Characteristic Input Voltage Control Voltage Power Dissipation Junction Temperature Operating Temperature Range Storage Temperature Range Ta=25°C Symbol VI VCT PD (Note1) PD (Note2) TJ Topr Tstg Rating 16 16 500 150 150 -40~+85 -55 ~ +150 2 Unit V V mW °C °C °C Note 1 : Mount on a glass epoxy circuit board of 30x30mm Pad dimension of 50mm Note 2 : No Heat sink Device Selection Guide Device S5215M S5218M S5225M S5228M S5230M S5233M S5250M Output Voltage 1.5V 1.8V 2.5V 2.8V 3.0V 3.3V 5.0V KSD-I5O005-003 2 S52xxM Electrical Characteristics (Electrical characteristics at VI=VO+1V IO=100uA, VCT≥2.0V CO=47uF, CBYP=1uF, Ta=25℃, unless otherwise specified.) , , Characteristic Symbol Device S5215M S5218M S5225M Test Condition 1V ≤VI -VO ≤10V, IO=100uA VI=VO+1V, IO=100uA ~ 100mA VCT≤0.4V (VO shutdown) IO=50mA, VCT≥2.0V Min 1.440 1.728 2.400 2.688 2.880 3.168 4.800 - Typ 1.5 1.8 2.5 2.8 3.0 3.3 5.0 0.3 8 0.01 1.5 Max 1.560 1.872 2.600 2.912 3.120 3.432 5.200 5 24 1 3.0 Unit V V V V V V V mV mV uA mA Output Voltage VO S5228M S5230M S5233M S5250M Line Regulation Load Regulation (Note3) Standby Current △VO(△VI) △VO(△IL) II(standby) All All All S5215M S5218M S5225M S5228M S5230M S5233M S5250M S5215M S5218M Quiescent Current (Note4) IQC IO=50mA, VCT≥2.0V - 0.8 1.5 mA IO=100mA IO=100mA - 400 500 500 600 mV mV Dropout Voltage VDROP S5225M S5228M S5230M S5233M S5250M All All All All IO=100mA - 140 250 mV Control Voltage (ON) Control Voltage (OFF) Control Current (ON) Control Current (OFF) VCT(ON) VCT(OFF) ICT(ON) ICT(OFF) VCT≥2.0V VCT≤0.4V 1.6 2 - 5 0.01 VI 0.4 10 1 V V uA uA Note 3 : Regulation is measured at constant junction temperature using low duty cycle pulse testing. Note 4 : Quiescent current is the regulator standby current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the quiescent current. KSD-I5O005-003 3 S52xxM ■Typical Application V I 1 2 3 VCT 5 Low- Noise Operation: CBYP=470pF, CO≥47uF Basic Operation: CBYP=not used, CO≥1uF Fig. 1 Fixed Voltage Regulator KSD-I5O005-003 5 VO 4 CBYP =1uF CO=47uF 4 S52xxM Electrical Characteristic Curves Fig.1 VDROP vs. IO 750 Fig.2 VO vs. IO 100 Dropout Voltage VDROP [mV] Relative Output Voltage [%] 600 S52xxM VI=Vo+1V S5215M 80 S5225M ~S5250M S5215M ~S5218M 450 60 300 40 S5218M S5225M~S5250M 150 20 00 25 50 75 100 125 150 0 50 100 150 200 250 300 350 Output Current IO [mA] Output Current IO [mA] Fig.3 VO vs. VCT S5225M~ S5250M VCT [V] 100 3 0 100 Fig.4 CBYP vs. Turn On Time Relative Output Voltage [%] 80 S5215M~ S5218M CBYP=10pF 75 60 Relative VO [%] CBYP=100pF 50 40 CBYP=1000pF 25 20 0 0 0.3 0.6 0 0.9 1.2 1.5 1.8 0 0 150 300 450 600 750 Control Voltage VCT [V] Turn On Time [us] Fig.5 PD vs. Ta 750 600 Power Dissipation [mW] 450 300 Without Heatshik 150 0 0 25 50 75 100 125 150 Ambient Temperature Ta [℃] KSD-I5O005-003 5 S52xxM Outline Dimension (Unit : mm) Recommend PCB Solder Land Dimension (Unit : mm) KSD-I5O005-003 6 S52xxM The AUK Corp. products are intended for the use as components in general electronic equipment (Office and communication equipment, measuring equipment, home appliance, etc.). Please make sure that you consult with us before you use these AUK Corp. products in equipments which require high quality and / or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, transportation, combustion control, all types of safety device, etc.). AUK Corp. cannot accept liability to any damage which may occur in case these AUK Corp. products were used in the mentioned equipments without prior consultation with AUK Corp.. Specifications mentioned in this publication are subject to change without notice. KSD-I5O005-003 7