ML12052-5P

ML12052 1.1 GHz Super Low Power Dual Modulus Prescaler MECL PLL COMPONENTS ÷64/65, ÷128/129 DUAL MODULUS PRESCALER SEMICONDUCTOR TECHNICAL DATA Legacy Device: Motorola MC12052A The ML12052 is a super low power dual modulus prescaler used in phase–locked loop applications with low power dissipation of 2.7 mW at a minimum supply voltage of 2.7 V. The ML12052 can be used with CMOS synthesizers requiring positive edges to trigger internal counters such as Motorola's MC145xxx or Lansdale’s ML145xxx series in a PLL to provide tuning signals up to 1.1 GHz in programmable frequency steps. A Divide Ratio Control (SW) permits selection of a 64/65 or 128/129 divide ratio as desired. The Modulus Control (MC) selects the proper divide number after SW has been biased to select the desired divide ratio. • 1.1 GHz Toggle Frequency • The ML12052 is Pin and Functionally Compatible with the Motorola or ON Semiconductor MC12022 • Low Power 1.0 mA Typical • 2.0 mA Maximum, VCC = 2.7 to 5.5 Vdc • Short Setup Time (tset) 16 ns Maximum @ 1.1 GHz • Modulus Control Input Level is Compatible with Standard CMOS and TTL • Maximum Input Voltage Should Be Limited to 6.5 Vdc • Operating Temperature Range TA = –40 to 85°C 8 1 SO 8 = -5P PLASTIC PACKAGE CASE 751 (SO–8) SO 8 MC12052AD ML12052-5P Note: Lansdale lead free (Pb) product, as it becomes available, will be identified by a part number prefix change from ML to MLE. PIN CONNECTIONS IN VCC SW OUT 1 2 3 4 8 7 6 5 IN NC MC Gnd FUNCTIONAL TABLE SW H H L L MC H L H L Divide Ratio 64 65 128 129 (Top View) NOTES: 1. SW: H = VCC, L = Open. A logic L can also be applied by grounding this pin, but this is not recommended due to increased power consumption. 2. MC: H = 2.0 V to VCC, L = GND to 0.8 V. MAXIMUM RATINGS Characteristic Power Supply Voltage, Pin 2 Operating Temperature Range Storage Temperature Range Modulus Control Input, Pin 6 Symbol VCC TA Tstg MC Range –0.5 to 7.0 –40 to 85 –65 to 150 –0.5 to 6.5 Unit Vdc °C °C Vdc Page 1 of 5 www.lansdale.com Issue A ML12052 LANSDALE Semiconductor, Inc. ELECTRICAL CHARACTERISTICS (VCC = 2.7 to 5.5 VDC, TA = –40 to 85°C, unless otherwise noted.) Characteristic Toggle Frequency (Sine Wave Input) Supply Current (Pin 2) Modulus Control Input High (MC) Modulus Control Input Low (MC) Divide Ratio Control Input High (SW) Divide Ratio Control Input Low (SW) Output Voltage Swing (Note 2) (CL = 8.0 pF, RL = 3.3 kΩ) Modulus Setup Time MC to Out @ 1100 MHz Input Voltage Sensitivity 250–1100 MHz 100–250 MHz Output Current (Note 1) VCC = 2.7 V, CL = 8.0 pF, RL = 3.3 kΩ VCC = 5.0 V, CL = 8.0 pF, RL = 7.2 kΩ Symbol ft ICC VIH1 VIL1 VIH2 VIL2 Vout tset Vin IO – – 0.5 0.5 3.0 3.0 Min 0.1 – 2.0 Gnd VCC – 0.5 V Open 0.8 – 100 400 Typ 1.4 1.0 – – VCC Open 1.1 11 – – Max 1.1 2.0 VCC + 0.5 V 0.8 VCC + 0.5 V Open – 16 1000 1000 Unit GHz mA V V VDC – VPP ns mVPP mA NOTES: 1. Divide ratio of ÷64/65 @ 1.1 GHz 2. Valid over voltage range 2.7 to 5.5 V; RL = 3.3 kΩ @ VCC = 2.7 V; RL = 7.2 kΩ @ VCC = 5.0 V Figure 1. Logic Diagram (ML12052) Figure 2. Modulus Setup Time D A C Q D B Q D C Q QB Prop. Delay In QB C QB CM In In Out MC MC Setup D D C QB C Q D QB E Q C D F QB C Q D QB G Q D H C SQ QB MC Out MC Release Modulus setup time MC to out is the MC setup or MC release plus the prop delay. SW Figure 3. AC Test Circuit VCC = 2.7 to 5.5 V C3 Sine Wave Generator C1 50 Ω C2 IN MC GND IN OUT CL RL EXTERNAL COMPONENTS C1 = C2 = 1000 pF C3 = 0.1 µF CL = 8.0pF (Including Scope and jig capacitance) RL = 3.3 kΩ @ VCC = 2.7 V RL = 7.2 kΩ @ VCC = 5.0 V VCC SW MC Input Page 2 of 5 www.lansdale.com Issue A ML12052 LANSDALE Semiconductor, Inc. Figure 4. Typical Input Impedance versus Input Frequency 300 200 R 100 0 –100 –200 –300 OHMS –400 –500 –600 –700 –800 jX –900 –1000 –1100 –1200 100 MHz 200 300 400 500 600 700 800 900 1000 1100 1200 Frequency (MHz) Page 3 of 5 www.lansdale.com Issue A ML12052 LANSDALE Semiconductor, Inc. Figure 5.. Generic block diagram showing prescaler connection to PLL device Prescaler Fout Fin PLL ML145146 ML145158 ML145159 ML12052 MC in MC VCO Loop Filter Figure 5 shows a generic block diagram for connecting a prescaler to a PLL device that supports dual modulus control. Application note AN535 decribes using a twomodulus prescaler technique.By using prescaler higher frequencies can be achieve than by a single CMOS PLL device. Page 4 of 5 www.lansdale.com Issue A ML12052 LANSDALE Semiconductor, Inc. OUTLINE DIMENSIONS SO = -5P (ML12052-5P) PLASTIC PACKAGE CASE 751-06 (SO–8) ISSUE T A 8 D 5 C E 1 4 H 0.25 M B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETER. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOW ABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0° 7° h B C e A SEATING PLANE X 45° θ L 0.10 A1 B 0.25 M CB S A S θ Lansdale Semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Lansdale does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. “Typical” parameters which may be provided in Lansdale data sheets and/or specifications can vary in different applications, and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by the customer’s technical experts. Lansdale Semiconductor is a registered trademark of Lansdale Semiconductor, Inc. Page 5 of 5 www.lansdale.com Issue A