DDR2-P-E3-U6

DDR2 SDRAM Controller - Pipelined Page 1 of 3 Home > Products > Intellectual Property > Lattice IP Cores > DDR2 SDRAM Controller - Pipelined DDR2 SDRAM Controller - Pipelined Overview The Double Data Rate (DDR) Synchronous Dynamic Random Access Memory (SDRAM) Controller is a general-purpose memory controller that interfaces with industry standard DDR2 SDRAM. The memory controller provides a generic command interface to the user's application. This interface reduces the effort to integrate the module with the remainder of the application and minimizes the need to deal with the DDR2 SDRAM command interface. The timing parameters for the memory can be set through the signals that are input to the core as part of the configuration interface. This enables switching between different memory devices and modification of timing parameters to suit the application using the same netlist. Features Interfaces to Industry Standard DDR2 SDRAM High-Performance DDR2 533/400/333/266/200/133 operation Programmable Burst Lengths of 4 or 8 Programmable CAS Latency of 3, 4, 5 or 6 Cycles Intelligent Bank Management to Minimize ACTIVE Commands Supports All Standard DDR Commands Synchronous Implementation for Reliable Operation Command Pipeline to Maximize Throughput Up to 4 chip selects for multiple DIMM support Supports all Common Memory Configurations http://www.latticesemi.com/products/intellectualproperty/ipcores/ddr2sdramcontrollerpip... 10/10/2011 DDR2 SDRAM Controller - Pipelined Page 2 of 3 SDRAM data path widths of 8, 16, 32, 64 and 72 bits Variable address widths for different memory devices Programmable timing parameters Byte level writing through Data Mask signals Burst termination The DDR2 SDRAM Controller - Pipelined is available as an IPexpress user configurable IP core, which allows the configuration of the IP and generation of a netlist and simulation file for use in designs. Please note that generating a bitstream may be prevented or the bitstream may have time logic present unless a license for the IP is purchased. Performance and Resource Utilization LatticeECP3 2 Parameter Settings User Guide Table 3-1 parameter defaults 1 SLICEs LUTs Registers I/O fMAX (MHz)3 1189 1386 1567 258 266 MHz (533 DDR2) 1. Performance and utilization characteristics are generated using LFE3-95E-8FN1156CES with Lattice ispLEVER 8.1 software in DDR2 mode. Performance may vary when using this IP core in a different density, speed or grade within the LatticeECP3 family. 2. SDRAM data path width of 32 bits. 3. The DDR2 IP core can operate at 266 MHz (533 DDR2) in the fastest speed-grade (-8) when the data width is 64 bits or less and 2 or fewer chip selects are used. For help with designs running at 266 MHz, contact your local sales office. LatticeECP2M/S 2 Parameter Settings User Guide Table 3-1 parameter defaults 1 3 SLICEs LUTs Registers I/O fMAX (MHz) 1234 1435 1530 258 266 MHz (533 DDR2) 1. Performance and utilization characteristics are generated using LFECP2M-35E-6F672C with Lattice ispLEVER 8.1 software in DDR2 mode. Performance may vary when using this IP core in a different density, speed or grade within the LatticeECP2M/S family. 2. SDRAM data path width of 32 bits. 3. The DDR2 IP core can operate at 266 MHz (533 DDR2) in the fastest speed-grade (-7) when the data width is 64 bits or less and 2 or fewer chip selects are used. For help with designs running at 266 MHz, contact your local sales office. LatticeECP2/S 2 Parameter Settings User Guide Table 3-1 parameter defaults 1 SLICEs LUTs Registers I/O fMAX (MHz)3 1234 1435 1530 258 266 MHz (533 DDR2) 1. Performance and utilization characteristics are generated using LFECP2-50E-6F672C Lattice ispLEVER 8.1 software in DDR2 mode. Performance may vary when using this IP core in a different density, speed or grade within the LatticeECP2/S family. 2. SDRAM data path width of 32 bits. 3. The DDR2 IP core can operate at 266 MHz (533 DDR2) in the fastest speed-grade (-7) when the data width is 64 bits or less and 2 or fewer chip selects are used. For help with designs running at 266 MHz, contact your local sales office. LatticeSC/M1 2 Parameter Settings User Guide Table 3-1 parameter defaults SLICEs LUTs Registers I/O fMAX (MHz) 1261 1490 1530 246 266 MHz (533 DDR2) 1. Performance and utilization characteristics are generated using LFSC3GA25E-6F900C Lattice ispLEVER 8.1 software in DDR2 mode. Performance may vary when using this IP core in a different density, speed or grade within the LatticeSC/M family. 2. SDRAM data path width of 32 bits. MachXO21 2 Parameter Settings User Guide Table 3-1 parameter defaults SLICEs LUTs Registers I/O fMAX (MHz) 704 1325 1118 152 133 MHz (266 DDR2) http://www.latticesemi.com/products/intellectualproperty/ipcores/ddr2sdramcontrollerpip... 10/10/2011 DDR2 SDRAM Controller - Pipelined Page 3 of 3 8.1 software. Performance may vary when using this IP core in a different density, speed or grade within the MachXO2 family. 2. SDRAM data path width of 16 bits. LatticeXP21 Parameter Settings2 User Guide Table 3-1 parameter defaults SLICEs LUTs Registers I/O fMAX (MHz) 1232 1433 1530 258 200 MHz (400 DDR2) 1. Performance and utilization characteristics are generated using LFXP2-17E-6F484C Lattice ispLEVER 8.1 software in DDR2 mode. Performance may vary when using this IP core in a different density, speed or grade within the LatticeXP2 family. 2. SDRAM data path width of 32 bits. Ordering Information Family LatticeECP3 LatticeECP2M/S LatticeECP2/S LatticeSC/M MachXO2 LatticeXP2 Part Number DDR2-P-E3-U6 DDR2-P-PM-U6 DDR2-P-P2-U6 DDR2-P-SC-U6 DDR2CTWB-M2-U DDR2-P-X2-U6 IP Version: 7.2 Evaluate: To download a full evaluation version of this IP, go to the IPexpress tool and click the IP Server button in the toolbar. All LatticeCORE IP cores and modules available for download will be visible. Purchase: To find out how to purchase the IP Core, please contact your local Lattice Sales Office. http://www.latticesemi.com/products/intellectualproperty/ipcores/ddr2sdramcontrollerpip... 10/10/2011