HIG-MAC-PM-UT3

HiGig Ethernet MAC Page 1 of 2 Home > Products > Intellectual Property > Lattice IP Cores > HiGig Ethernet MAC HiGig™ MAC Overview The HiGig™ MAC transmits and receives data between a host processor and a HiGig™ / Ethernet network that enables networking customers to add features like quality of service (QoS), port trunking, mirroring across devices, and link aggregation at higher layers of the OSI network model. The HiGig™ MAC ensures that the Media Access rules specified in the 802.3ae IEEE standard and HiGig™ Protocol definitions are met while transmitting a frame of data over Ethernet. On the receive side, it extracts the different components of a frame and transfers them to higher applications through a FIFO interface. The HiGig™ / Ethernet MAC IP core is a user-configurable IP core, which allows the configuration of the IP and generation of a netlist and simulation file for use in designs. Please note that generating a bitstream may be prevented or the bitstream may have time logic present unless a license for the IP is purchased. The HiGig™ MAC IP core from Lattice supports the LatticeECP3 and LatticeSC/M FPGA families. Features Core Block Diagram Compliant to the Broadcom HiGig and HiGig2 Protocol Definitions 64-bit wide internal data path operating at a maximum frequency of 187.5 MHz (LatticeECP3 maximum 156 MHz) XGMII interface to the PHY layer (using IODDR external to the core) XAUI interface to the PHY layer (using PCS/SERDES external to the core) Simple FIFO interface with user’s application Optional multicast address filtering Transmit and receive statistics vector Optional statistics counters of length from 16 to 40 (external to the core) Variable-sized packet transmission with fixed sized messaging capability (HiGig2 Only) Programmable Inter Frame Gap Supports: Full duplex operation Flow control using PAUSE frames (for HiGig) and messaging (for HiGig2) Automatic padding of short frames Optional FCS generation during transmission Optional FCS stripping during reception Jumbo frames up to 16k Inter frame Stretch Mode during transmission Deficit Idle Count Performance and Resource Utilization LatticeECP3 FPGA Family HiGig2 Results for LatticeECP31 SLICEs LUTs Registers External Pins2 Mode With Multicast Address Filtering and 16-bit Statistics Counters 3624 4706 3386 83 sysMEM EBRs fMAX (MHz) 4 157 1. Performance and utilization data are generated using an LFE3-35EA-7FN672CES device with Lattice Diamond 1.1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeECP3 family. 2. The HiGig Ethernet MAC IP core itself does not use any external pins. However, in an application the core is used together IODDR and I/O Buffers integrated in the LatticeECP3 series FPGA. Thus the application implementing the HiGig MAC specification will utilize I/O pins. 1 HiGig Results for LatticeECP3 Mode With Multicast Address Filtering and 16-bit Statistics Counters SLICEs LUTs Registers External Pins2 3280 4135 3121 78 sysMEM EBRs fMAX (MHz) 4 158 1. Performance and utilization data are generated using an LFE3-35EA-7FN672CES device with Lattice Diamond 1.1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeECP3 family. 2. The HiGig Ethernet MAC IP core itself does not use any external pins. However, in an application the core is used together IODDR and I/O Buffers integrated in the LatticeECP3 series FPGA. Thus the application implementing the HiGig MAC specification will utilize I/O pins. http://www.latticesemi.com/products/intellectualproperty/ipcores/higigethernetmac/index.... 10/11/2011 HiGig Ethernet MAC Page 2 of 2 LatticeSC/M FPGA Family HiGig2 Results for LatticeSC/M1 SLICEs LUTs Registers External Pins2 Mode With Multicast Address Filtering and 16-bit Statistics Counters 3417 4879 3380 83 sysMEM EBRs fMAX (MHz) 4 206 1. Performance and utilization data are generated using an LFSCM3GA25EP1-5F900C device with Lattice Diamond 1.1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeSCM family. 2. The HiGig2 Ethernet MAC IP core itself does not use any external pins. However, in an application the core is used together IODDR and I/O Buffers integrated in the LatticeSCM series FPGA. Thus the application implementing the HiGig2 MAC specification will utilize I/O pins. HiGig Results for LatticeSC/M Mode With Multicast Address Filtering and 16-bit Statistics Counters 1 SLICEs LUTs Registers External Pins2 2995 4188 3062 78 sysMEM EBRs fMAX (MHz) 4 204 1. Performance and utilization data are generated using an LFSCM3GA25EP1-5F900C device with Lattice Diamond 1.1 software. Performance may vary when using a different software version or targeting a different device density or speed grade within the LatticeSCM family. 2. The HiGig Ethernet MAC IP core itself does not use any external pins. However, in an application the core is used together IODDR and I/O Buffers integrated in the LatticeSCM series FPGA. Thus the application implementing the HiGig MAC specification will utilize I/O pins. Ordering Information Family LatticeECP3 LatticeSC Part Numbers HIG-MAC-E3-U3 HIG-MAC-SC-U3 Evaluate/Purchase: Unlike other LatticeCORE IP, the HiGig™ MAC IP core cannot be directly downloaded from the Lattice IPexpress Server. Please request this IP from Lattice at lic_admn@latticesemi.com and include your name, company, and complete contact information. A setup file for installation of the IP into IPexpress will be sent to you. Execute the setup file and then use IPexpress to evaluate and configure the IP core. For more information on customizing an IP please read the IPexpress Quick Start Guide. Purchase: To find out how to purchase the IP Core, please contact your local Lattice Sales Office. HiGig™, HiGig2™ are trademarks of Broadcom Corporation. http://www.latticesemi.com/products/intellectualproperty/ipcores/higigethernetmac/index.... 10/11/2011