iCE40 UltraPlus Family Data Sheet
Data Sheet
FPGA-DS-02008-1.9
December 2020
iCE40 UltraPlus Family Data Sheet
Data Sheet
Disclaimers
Lattice makes no warranty, representation, or guarantee regarding the accuracy of information contained in this document or the suitability of its
products for any particular purpose. All information herein is provided AS IS and with all faults, and all risk associated with such information is entirely
with Buyer. Buyer shall not rely on any data and performance specifications or parameters provided herein. Products sold by Lattice have been
subject to limited testing and it is the Buyer's responsibility to independently determine the suitability of any products and to test and verify the
same. No Lattice products should be used in conjunction with mission- or safety-critical or any other application in which the failure of Lattice’s
product could create a situation where personal injury, death, severe property or environmental damage may occur. The information provided in this
document is proprietary to Lattice Semiconductor, and Lattice reserves the right to make any changes to the information in this document or to any
products at any time without notice.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
2
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Contents
Acronyms in This Document ................................................................................................................................................. 7
1. General Description ...................................................................................................................................................... 8
1.1.
Features .............................................................................................................................................................. 8
2. Product Family .............................................................................................................................................................. 9
2.1.
Overview ............................................................................................................................................................. 9
3. Architecture ................................................................................................................................................................ 11
3.1.
Architecture Overview ...................................................................................................................................... 11
3.1.1. PLB Blocks ..................................................................................................................................................... 12
3.1.2. Routing.......................................................................................................................................................... 13
3.1.3. Clock/Control Distribution Network ............................................................................................................. 13
3.1.4. sysCLOCK Phase Locked Loops (PLLs) ........................................................................................................... 14
3.1.5. sysMEM Embedded Block RAM Memory ..................................................................................................... 15
3.1.6. sysMEM Single Port RAM Memory (SPRAM) ................................................................................................ 17
3.1.7. sysDSP ........................................................................................................................................................... 18
3.1.8. sysI/O Buffer Banks ....................................................................................................................................... 23
3.1.9. sysI/O Buffer ................................................................................................................................................. 26
3.1.10. On-Chip Oscillator ......................................................................................................................................... 26
3.1.11. User I2C IP ..................................................................................................................................................... 27
3.1.12. User SPI IP ..................................................................................................................................................... 27
3.1.13. RGB High Current Drive I/O Pins ................................................................................................................... 27
3.1.14. RGB PWM IP ................................................................................................................................................. 27
3.1.15. Non-Volatile Configuration Memory ............................................................................................................ 28
3.2.
iCE40 UltraPlus Programming and Configuration ............................................................................................. 28
3.2.1. Device Programming..................................................................................................................................... 28
3.2.2. Device Configuration .................................................................................................................................... 28
3.2.3. Power Saving Options ................................................................................................................................... 28
4. DC and Switching Characteristics ............................................................................................................................... 29
4.1.
Absolute Maximum Ratings .............................................................................................................................. 29
4.2.
Recommended Operating Conditions ............................................................................................................... 29
4.3.
Power Supply Ramp Rates ................................................................................................................................ 30
4.4.
Power-On Reset ................................................................................................................................................ 30
4.5.
Power-up Supply Sequence............................................................................................................................... 30
4.6.
External Reset ................................................................................................................................................... 30
4.7.
Power-On-Reset Voltage Levels ........................................................................................................................ 31
4.8.
ESD Performance .............................................................................................................................................. 31
4.9.
DC Electrical Characteristics .............................................................................................................................. 32
4.10. Supply Current .................................................................................................................................................. 32
4.11. User I2C Specifications ....................................................................................................................................... 33
4.12. I2C 50 ns Delay ................................................................................................................................................... 33
4.13. I2C 50 ns Filter ................................................................................................................................................... 33
4.14. User SPI Specifications ...................................................................................................................................... 33
4.15. Internal Oscillators (HFOSC, LFOSC) .................................................................................................................. 34
4.16. sysI/O Recommended Operating Conditions .................................................................................................... 34
4.17. sysI/O Single-Ended DC Electrical Characteristics ............................................................................................. 34
4.18. Differential Comparator Electrical Characteristics ............................................................................................ 35
4.19. Typical Building Block Function Performance ................................................................................................... 35
4.19.1. Pin-to-Pin Performance (LVCMOS25) ........................................................................................................... 35
4.19.2. Register-to-Register Performance ................................................................................................................ 35
4.20. sysDSP Timing ................................................................................................................................................... 36
4.21. SPRAM Timing ................................................................................................................................................... 36
4.22. Derating Logic Timing ........................................................................................................................................ 36
4.23. Maximum sysI/O Buffer Performance .............................................................................................................. 36
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
3
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.24. iCE40 UltraPlus Family Timing Adders...............................................................................................................37
4.25. iCE40 UltraPlus External Switching Characteristics ...........................................................................................37
4.26. sysCLOCK PLL Timing .........................................................................................................................................38
4.27. SPI Master or NVCM Configuration Time ..........................................................................................................38
4.28. sysCONFIG Port Timing Specifications...............................................................................................................39
4.29. RGB LED Drive ...................................................................................................................................................40
4.30. Switching Test Conditions .................................................................................................................................40
5. Pinout Information .....................................................................................................................................................41
5.1.
Signal Descriptions ............................................................................................................................................41
5.1.1. Power Supply Pins .........................................................................................................................................41
5.1.2. Configuration Pins .........................................................................................................................................41
5.1.3. Configuration SPI Pins ...................................................................................................................................42
5.1.4. Global Pins ....................................................................................................................................................43
5.1.5. General I/O, LED Pins ....................................................................................................................................44
5.2.
Pin Information Summary .................................................................................................................................45
5.3.
iCE40UP Part Number Description ....................................................................................................................46
5.3.1. Tape and Reel Quantity ................................................................................................................................46
5.4.
Ordering Part Numbers .....................................................................................................................................46
5.4.1. Industrial .......................................................................................................................................................46
Supplemental Information..................................................................................................................................................47
Technical Support ...............................................................................................................................................................48
Revision History ..................................................................................................................................................................49
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
4
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Figures
Figure 3.1. iCE40UP5K Device, Top View ............................................................................................................................ 11
Figure 3.2. PLB Block Diagram ............................................................................................................................................ 12
Figure 3.3. PLL Diagram ...................................................................................................................................................... 14
Figure 3.4. sysMEM Memory Primitives ............................................................................................................................. 16
Figure 3.5. SPRAM Primitive ............................................................................................................................................... 17
Figure 3.6. sysDSP Functional Block Diagram (16-bit x 16-bit Multiply-Accumulate) ........................................................ 19
Figure 3.7. sysDSP 8-bit x 8-bit Multiplier........................................................................................................................... 22
Figure 3.8. DSP 16-bit x 16-bit Multiplier ........................................................................................................................... 23
Figure 3.9. I/O Bank and Programmable I/O Cell ............................................................................................................... 24
Figure 3.10. iCE I/O Register Block Diagram ....................................................................................................................... 25
Figure 4.1. Power Up Sequence with SPE_VCCIO1 and VPP_2V5 Not Connected Together.............................................. 31
Figure 4.2. Power Up Sequence with All Supplies Connected Together to 1.8 V ............................................................... 31
Figure 4.3. Output Test Load, LVCMOS Standards ............................................................................................................. 40
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
5
iCE40 UltraPlus Family Data Sheet
Data Sheet
Tables
Table 2.1. iCE40 UltraPlus Family Selection Guide ...............................................................................................................9
Table 3.1. Logic Cell Signal Descriptions .............................................................................................................................13
Table 3.2. Global Buffer (GBUF) Connections to Programmable Logic Blocks....................................................................13
Table 3.3. PLL Signal Descriptions .......................................................................................................................................15
Table 3.4. sysMEM Block Configurations ............................................................................................................................15
Table 3.5. EBR Signal Descriptions ......................................................................................................................................16
Table 3.6. SPRAM Signal Descriptions ................................................................................................................................18
Table 3.7. Output Block Port Description ...........................................................................................................................19
Table 3.8. PIO Signal List .....................................................................................................................................................25
Table 3.9. Supported Input Standards ................................................................................................................................26
Table 3.10. Supported Output Standards ...........................................................................................................................26
Table 3.11. iCE40 UltraPlus Power Saving Features Description ........................................................................................28
Table 4.1. Absolute Maximum Ratings ...............................................................................................................................29
Table 4.2. Recommended Operating Conditions ................................................................................................................29
Table 4.3. Power Supply Ramp Rates .................................................................................................................................30
Table 4.4. Power-On-Reset Voltage Levels .........................................................................................................................31
Table 4.5. DC Electrical Characteristics ...............................................................................................................................32
Table 4.6. Supply Current ...................................................................................................................................................32
Table 4.7. User I2C Specifications ........................................................................................................................................33
Table 4.8. I2C 50 ns Delay ....................................................................................................................................................33
Table 4.9. I2C 50 ns Filter ....................................................................................................................................................33
Table 4.10. User SPI Specifications .....................................................................................................................................33
Table 4.11. Internal Oscillators (HFOSC, LFOSC) .................................................................................................................34
Table 4.12. sysI/O Recommended Operating Conditions ...................................................................................................34
Table 4.13. sysI/O Single-Ended DC Electrical Characteristics ............................................................................................34
Table 4.14. Differential Comparator Electrical Characteristics ...........................................................................................35
Table 4.15. Pin-to-Pin Performance (LVCMOS25)...............................................................................................................35
Table 4.16. Register-to-Register Performance....................................................................................................................35
Table 4.17. sysDSP Timing ..................................................................................................................................................36
Table 4.18. Single Port RAM Timing....................................................................................................................................36
Table 4.19. Maximum sysI/O Buffer Performance .............................................................................................................36
Table 4.20. iCE40 UltraPlus Family Timing Adders .............................................................................................................37
Table 4.21. iCE40 UltraPlus External Switching Characteristics ..........................................................................................37
Table 4.22. sysCLOCK PLL Timing ........................................................................................................................................38
Table 4.23. SPI Master or NVCM Configuration Time .........................................................................................................38
Table 4.24. sysCONFIG Port Timing Specifications .............................................................................................................39
Table 4.25. RGB LED ............................................................................................................................................................40
Table 4.26. Test Fixture Required Components, Non-Terminated Interfaces ....................................................................40
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
6
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Acronyms in This Document
A list of acronyms used in this document.
Acronym
Definition
DFF
DSP
EBR
HFOSC
I2 C
LFOSC
LUT
LVCMOS
NVCM
PCLK
PFU
PIC
PLB
PLL
SoC
SPI
SPR
WLCSP
D-style Flip-Flop
Digital Signal Processor
Embedded Block RAM
High Frequency Oscillator
Inter-Integrated Circuit
Low Frequency Oscillator
Look Up Table
Low-Voltage Complementary Metal Oxide Semiconductor
Non Volatile Configuration Memory
Primary Clock
Programmable Functional Unit
Programmable I/O Cells
Programmable Logic Blocks
Phase Locked Loops
System on a Chip
Serial Peripheral Interface
Single Port RAM
Wafer Level Chip Scale Packaging
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
7
iCE40 UltraPlus Family Data Sheet
Data Sheet
1. General Description
iCE40 UltraPlus™ family from Lattice Semiconductor is
an ultra-low power FPGA and sensor manager
designed for ultra-low power mobile applications, such
as smartphones, tablets and hand-held devices. iCE40
UltraPlus is compatible with Lattice's iCE40 Ultra family
devices, containing all the functions iCE40 Ultra family
has except the high current IR LED driver. In addition,
the iCE40 UltraPlus features an additional 1 Mb SRAM,
additional DSP blocks, with additional LUTs, all which
can be used to support an always-on Voice Recognition
function in the mobile devices, without the need to
keep the higher power consuming voice codec on all
the time.
The iCE40 UltraPlus family includes integrated SPI and
I2C blocks to interface with virtually all mobile sensors
and application processors. In addition, the iCE40
UltraPlus family also features two I/O pins that can
support the interface to I3C devices. There are two
on-chip oscillators, 10 kHz and 48 MHz, the LFOSC
(10 kHz) is ideal for low power function in always-on
applications, while HFOSC (48 MHz) can be used for
awaken activities.
The iCE40 UltraPlus family also features DSP functional
block to off-load Application Processor to pre-process
information sent from the mobile device, such as voice
data. The RGB PWM IP, with the three 24 mA constant
current RGB outputs on the iCE40 UltraPlus provides
all the necessary logic to directly drive the service LED,
without the need of external MOSFET or buffer.
The iCE40 UltraPlus family of devices are targeting for
mobile applications to perform all the functions in
iCE40 Ultra devices, such as Service LED, GPIO
Expander, SDIO Level Shift, and other custom
functions. In addition, the iCE40 UltraPlus family
devices are also targeting for Voice Recognition
application.
The iCE40 UltraPlus family features two device
densities, 2800 to 5280 Look Up Tables (LUTs) of logic
with programmable I/Os that can be used as either
SPI/I2C interface ports or general purpose I/O’s. Two of
the iCE40 UltraPlus I/Os can be used to interface to
higher performance I3C. It also has up to 120 kb of
Block RAMs, plus 1024 kb of Single Port SRAMs to work
with user logic.
1.1. Features
Flexible Logic Architecture
Two devices with 2800 to 5280 LUTs
Offered in WLCS and QFN packages
Ultra-low Power Devices
Advanced 40 nm low power process
As low as 100 µA standby current typical
Embedded Memory
Up to 1024 kb Single Port SRAM
Up to 120 kb sysMEM™ Embedded Block RAM
Two Hardened I2C Interfaces
Two I/O pins to support I3C interface
Two Hardened SPI Interfaces
Two On-Chip Oscillators
Low Frequency Oscillator – 10 kHz
High Frequency Oscillator – 48 MHz
24 mA Current Drive RGB LED Outputs
Three drive outputs in each device
User selectable sink current up to 24 mA
On-chip DSP
Signed and unsigned 8-bit or 16-bit functions
Functions include Multiplier, Accumulator, and
Multiply-Accumulate (MAC)
Flexible On-Chip Clocking
Eight low skew global signal resource, six can
be directly driven from external pins
One PLL with dynamic interface per device
Flexible Device Configuration
SRAM is configured through:
Standard SPI Interface
Internal Nonvolatile Configuration Memory
(NVCM)
Ultra-Small Form Factor
As small as 2.11 mm × 2.54 mm
Applications
Always-On Voice Recognition Application
Smartphones
Tablets and Consumer Handheld Devices
Handheld Commercial and Industrial Devices
Multi Sensor Management Applications
Sensor Pre-processing and Sensor Fusion
Always-On Sensor Applications
USB 3.1 Type C Cable Detect / Power Delivery
Applications
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
8
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
2. Product Family
Table 2.1 lists device information and packages of the iCE40 UltraPlus family.
Table 2.1. iCE40 UltraPlus Family Selection Guide
Part Number
Logic Cells (LUT + Flip-Flop)
iCE40UP3K
iCE40UP5K
2800
5280
EBR Memory Blocks
20
30
EBR Memory Bits (Kbits)
80
120
SPRAM Memory Blocks
4
4
1024
1024
Yes
Yes
PLL
1
1
DSP Blocks (MULT16 with 32-bit Accumulator
4
8
SPRAM Memory Bits (Kbits)
NVCM
Hardened
I2C,
2, 2
2, 2
HF Oscillator (48 MHz)
SPI
1
1
LF Oscillator (10 KHz)
1
1
24 mA LED Sink
3
3
PWM IP Block
Yes
Packages, ball pitch, dimension
30-ball WLCSP, 0.4 mm, 2.11 mm × 2.54 mm
48-ball QFN, 0.5 mm, 7.0 mm × 7.0 mm
Yes
Total User I/O Count
21
21
-
39
2.1. Overview
The iCE40 UltraPlus family of ultra-low power FPGAs has three devices with densities ranging from 2800 to 5280 LookUp Tables (LUTs) fabricated in a 40 nm Low Power CMOS process. In addition to LUT-based, low-cost programmable
logic, these devices also feature Embedded Block RAM (EBR), Single Port RAM (SPRAM), on-chip Oscillators (LFOSC,
HFOSC), two hardened I2C Controllers, two hardened SPI Controllers, PWM IP, three 24 mA RGB LED open-drain
drivers, I3C interface pins, and DSP blocks. These features allow the devices to be used in low-cost, high-volume
consumer and mobile applications.
The iCE40 UltraPlus FPGAs are available in very small form factor packages, as small as 2.11 mm × 2.54 mm. The small
form factor allows the device to easily fit into a lot of mobile applications, where space can be limited. Table 2.1 lists
the LUT densities, package and I/O pin count.
The iCE40 UltraPlus devices offer I/O features such as pull-up resistors. Pull-up features are controllable on a “per pin”
basis. In addition, the iCE40 UltraPlus devices offer two I/Os with dynamic control on the pull-up resistors to support
I3C interface.
The RGB PWM IP in the iCE40 UltraPlus devices provides controls for driving the 24 mA LED Sink driver, including color
controls, LED ON/OFF time, and breathe rate.
The iCE40 UltraPlus devices also provide flexible, reliable and secure configuration from on-chip NVCM. These devices
can also configure themselves from external SPI Flash, or be configured by an external master such as a CPU.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Lattice provides a variety of design tools that allow complex designs to be efficiently implemented using the iCE40
UltraPlus family of devices. Popular logic synthesis tools provide synthesis library support for iCE40 UltraPlus. Lattice
design tools use the synthesis tool output along with the user-specified preferences and constraints to place and route
the design in the iCE40 UltraPlus device. These tools extract the timing from the routing and back-annotate it into the
design for timing verification.
Lattice provides many pre-engineered IP (Intellectual Property) modules, including a number of reference designs,
licensed free of charge, optimized for the iCE40 UltraPlus FPGA family. Lattice also can provide fully verified bitstream
for some of the widely used target functions in mobile device applications, such as ultra-low power sensor
management, gesture recognition, IR remote, barcode emulator functions. Users can use these functions as offered by
Lattice, or they can use the design to create their own unique required functions. For more information regarding
Lattice's reference designs or fully-verified bitstreams, contact your local Lattice representative.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
10
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
3. Architecture
3.1. Architecture Overview
The iCE40 UltraPlus family architecture contains an array of Programmable Logic Blocks (PLB), two Oscillator
Generators, two user configurable I2C controllers, two user configurable SPI controllers, blocks of sysMEM™ Embedded
Block RAM (EBR) and Single Port RAM (SPRAM) surrounded by Programmable I/O (PIO). Figure 3.1 shows the block
diagram of the iCE40UP5K device.
DSP
50 ns Filter
NVCM
5 PLB Rows
50 ns Filter
DSP
5 4 Kb DPRAM
5 4 Kb DPRAM
5 4 Kb DPRAM
256 Kb
SPRAM
50 ns Delay
50 ns Delay
DSP
5 4 Kb DPRAM
5 4 Kb DPRAM
LFOSC
5 4 Kb DPRAM
DSP
DSP
DSP
DSP
256 Kb
SPRAM
I2C
8 Logic Cells = Programmable Logic Block
PLL
HFOSC
256 Kb
SPRAM
I3C I/O
I3C I/O
I/O Bank 0
config
256 Kb
SPRAM
DSP
PWM IP
I2 C
RGB I/O
RGB I/O
RGB I/O
PLB
config
SPI
I/O Bank 2
I/O Bank 1_SPI
SPI
Carry Logic
4-Input Look-up
Table (LUT)
Flip-flop with Enableand Reset Controls
Figure 3.1. iCE40UP5K Device, Top View
The Programmable Logic Blocks (PLB) and sysMEM EBR blocks, are arranged in a two-dimensional grid with rows and
columns. Each column has either PLB or EBR blocks. The PIO cells are located at the top and bottom of the device,
arranged in banks. The PLB contains the building blocks for logic, arithmetic, and register functions. The PIOs utilize a
flexible I/O buffer referred to as a sysI/O buffer that supports operation with a variety of interface standards. The
blocks are connected with many vertical and horizontal routing channel resources. The place and route software tool
automatically allocates these routing resources.
In the iCE40 UltraPlus family, there are three sysI/O banks, one on top and two at the bottom. User can connect some
VCCIOs together, if all the I/Os are using the same voltage standard. See the Power-up Supply Sequence section. The
sysMEM EBRs are large 4 kb, dedicated fast memory blocks. These blocks can be configured as RAM, ROM or FIFO with
user logic using PLBs.
In addition to the EBR, the iCE40 UltraPlus devices also feature four 256 kb SPRAM blocks that can be cascaded to
create up to 1 Mb block. It is useful for temporary storage of large quantities of information.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
11
iCE40 UltraPlus Family Data Sheet
Data Sheet
Every device in the family has two user SPI ports, one of these (right side) SPI ports also supports programming and
configuration of the device. The iCE40 UltraPlus also includes two user I2C ports, two oscillators, and high current RGB
LED sink.
3.1.1. PLB Blocks
The core of the iCE40 UltraPlus device consists of Programmable Logic Blocks (PLB) which can be programmed to
perform logic and arithmetic functions. Each PLB consists of eight interconnected Logic Cells (LC) as shown in Figure
3.2. Each LC contains one LUT and one register.
Shared Block-Level Controls
Clock
Programmable
Logic Block (PLB)
Enable
FCOUT
1
Set/Reset
0
Logic Cell
Carry Logic
8 Logic Cells (LCs)
DFF
I0
D
I1
EN
LUT
I2
O
Q
SR
I3
FCIN
Four-input
Look-Up Table
(LUT)
Flip-flop with
optional enable and
set or reset controls
= Statically defined by configuration program
Figure 3.2. PLB Block Diagram
Logic Cells
Each Logic Cell includes three primary logic elements shown in Figure 3.2.
A four-input Look-Up Table (LUT) builds any combinational logic function, of any complexity, requiring up to four
inputs. Similarly, the LUT element behaves as a 16x1 Read-Only Memory (ROM). Combine and cascade multiple
LUTs to create wider logic functions.
A ‘D’-style Flip-Flop (DFF), with an optional clock-enable and reset control input, builds sequential logic functions.
Each DFF also connects to a global reset signal that is automatically asserted immediately following device
configuration.
Carry Logic boosts the logic efficiency and performance of arithmetic functions, including adders, subtracters,
comparators, binary counters and some wide, cascaded logic functions.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
12
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Table 3.1 lists the logic cell signals.
Table 3.1. Logic Cell Signal Descriptions
Function
Type
Signal Name
Description
Input
Data signal
I0, I1, I2, I3
Inputs to LUT
Input
Control signal
Enable
Clock enable shared by all LCs in the PLB
Input
Control signal
Set/Reset*
Input
Control signal
Clock
Asynchronous or synchronous local set/reset shared by
all
LCsone
in the
PLB.eight Global Buffers, or from the
Clock
of the
Input
Inter-PLB signal
FCIN
Output
Data signals
O
general-purpose
interconnects fabric shared by all LCs
Fast
carry in
in the PLB
LUT or registered output
Output
Inter-PFU signal
FCOUT
Fast carry out
*Note: If Set/Reset is not used, then the flip-flop is never set/reset, except when cleared immediately after configuration.
3.1.2. Routing
There are many resources provided in the iCE40 UltraPlus devices to route signals individually with related control
signals. The routing resources consist of switching circuitry, buffers and metal interconnect (routing) segments.
The inter-PLB connections are made with three different types of routing resources: Adjacent (spans two PLBs), x4
(spans five PLBs) and x12 (spans thirteen PLBs). The Adjacent, x4 and x12 connections provide fast and efficient
connections in the diagonal, horizontal and vertical directions.
The design tool takes the output of the synthesis tool and places and routes the design.
3.1.3. Clock/Control Distribution Network
Each iCE40 UltraPlus device has six global inputs, two pins on the top bank and four pins on the bottom bank.
These global inputs can be used as high fanout nets, clock, reset or enable signals. The dedicated global pins are
identified as Gxx and each drives one of the eight global buffers. The global buffers are identified as GBUF[7:0]. These
six inputs may be used as general purpose I/O if they are not used to drive the clock nets.
Table 3.2 lists the connections between a specific global buffer and the inputs on a PLB. All global buffers optionally
connect to the PLB CLK input. Any four of the eight global buffers can drive logic inputs to a PLB. Even-numbered global
buffers optionally drive the Set/Reset input to a PLB. Similarly, odd-numbered buffers optionally drive the PLB clockenable input. GBUF[7:6, 3:0] can connect directly to G[7:6, 3:0] pins respectively. GBUF4 and GBUF5 can connect to the
two on-chip Oscillator Generators (GBUF4 connects to LFOSC, GBUF5 connects to HFOSC).
Table 3.2. Global Buffer (GBUF) Connections to Programmable Logic Blocks
Global Buffer
LUT Inputs
Clock
Reset
Clock Enable
—
GBUF0
GBUF1
—
GBUF2
—
—
—
GBUF5
—
GBUF6
—
GBUF7
—
GBUF3
GBUF4
Yes, any 4 of 8 GBUF
Inputs
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
13
iCE40 UltraPlus Family Data Sheet
Data Sheet
The maximum frequency for the global buffers are listed in Table 4.21.
Global Hi-Z Control
The global high-impedance control signal, GHIZ, connects to all I/O pins on the iCE40 UltraPlus device. This GHIZ signal
is automatically asserted throughout the configuration process, forcing all user I/O pins into their high-impedance
state.
Global Reset Control
The global reset control signal connects to all PLB and PIO flip-flops on the iCE40 UltraPlus device. The global reset
signal is automatically asserted throughout the configuration process, forcing all flip-flops to their defined wake-up
state. For PLB flip-flops, the wake-up state is always reset, regardless of the PLB flip-flop primitive used in the
application.
3.1.4. sysCLOCK Phase Locked Loops (PLLs)
The sysCLOCK PLLs provide the ability to synthesize clock frequencies. The iCE40 UltraPlus devices have one sysCLOCK
PLL. REFERENCECLK is the reference frequency input to the PLL and its source can come from an external I/O pin, the
internal Oscillator Generators from internal routing. EXTFEEDBACK is the feedback signal to the PLL which can come
from internal routing or an external I/O pin. The feedback divider is used to multiply the reference frequency and thus
synthesize a higher frequency clock output.
The PLLOUT output has an output divider, thus allowing the PLL to generate different frequencies for each output. The
output divider can have a value from 1 to 64 (in increments of 2X). The PLLOUT outputs can all be used to drive the
iCE40 UltraPlus global clock network directly or general purpose routing resources can be used.
The LOCK signal is asserted when the PLL determines it has achieved lock and de-asserted if a loss of lock is detected. A
block diagram of the PLL is shown in Figure 3.3.
The timing of the device registers can be optimized by programming a phase shift into the PLLOUT output clock which
will advance or delay the output clock with reference to the REFERENCECLK clock. This phase shift can be either
programmed during configuration or can be adjusted dynamically. In dynamic mode, the PLL may lose lock after a phase
adjustment on the output used as the feedback source and not relock until the tLOCK parameter has been satisfied.
For more details, refer to iCE40 sysCLOCK PLL Design and Usage Guide (FPGA-TN-02052).
RESET
BYPAS S
BYPAS S
GNDPLL
REFERENCECLK
DIVR
Phase
Detector
In put
Divider
RANGE
Lo w-Pass
Filter
VCCPLL
DIVQ
Vol tage
Control led
Oscill ator
(VCO)
VCO
Divider
SIMPLE
DIVF
PLLOUTCORE
Feed back
Divider
Fine Delay
Adjustment
Feed back
Feed back_Path
PLLOUTGLOBAL
LOCK
DYNAMICDELAY[7:0]
EXTFEEDBACK
LATCHINPUTVALUE
Phase
Shifter
Fine Delay
Adjustment
Output Port
EXTERNAL
Lo w Power mode
(iCEgate enabled)
Figure 3.3. PLL Diagram
Table 3.3 provides signal descriptions of the PLL block.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
14
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Table 3.3. PLL Signal Descriptions
Signal Name
Direction
Description
REFERENCECLK
Input
Input reference clock
BYPASS
Input
The BYPASS control selects which clock signal connects to the PLLOUT output.
0 – PLL generated signal
1 – REFERENCECLK
EXTFEEDBACK
Input
External feedback input to PLL. Enabled when the FEEDBACK_PATH attribute is set
to EXTERNAL.
DYNAMICDELAY[7:0]
Input
Fine delay adjustment control inputs. Enabled when DELAY_ADJUSTMENT_MODE
is set to DYNAMIC.
LATCHINPUTVALUE
Input
When enabled, puts the PLL into low-power mode; PLL output is held static at the
last input clock value. Set ENABLE ICEGATE_PORTA and PORTB to ‘1’ to enable.
PLLOUTGLOBAL
Output
Output from the Phase-Locked Loop (PLL). Drives a global clock network on the
FPGA. The port has optimal connections to global clock buffers GBUF4 and GBUF5.
PLLOUTCORE
Output
LOCK
Output
RESET
Input
Output clock generated by the PLL, drives regular FPGA routing. The frequency
generated on this output is the same as the frequency of the clock signal generated
on the PLLOUTLGOBAL port.
When High, indicates that the PLL output is phase aligned or locked to the input
reference clock.
Active low reset.
SCLK
Input
Input, Serial Clock used for re-programming PLL settings.
SDI
Input
Input, Serial Data used for re-programming PLL settings.
3.1.5. sysMEM Embedded Block RAM Memory
Larger iCE40 UltraPlus device includes multiple high-speed synchronous sysMEM Embedded Block RAMs (EBRs), each
4 kbit in size. This memory can be used for a wide variety of purposes including data buffering and FIFO.
sysMEM Memory Block
The sysMEM block can implement single port, pseudo dual port, or FIFO memories with programmable logic resources.
Each block can be used in a variety of depths and widths as listed in Table 3.4.
Table 3.4. sysMEM Block Configurations
Block RAM
Configuration
SB_RAM256x16
SB_RAM256x16NR
SB_RAM256x16NW
SB_RAM256x16NRNW
SB_RAM512x8
SB_RAM512x8NR
SB_RAM512x8NW
SB_RAM512x8NRNW
SB_RAM1024x4
SB_RAM1024x4NR
SB_RAM1024x4NW
SB_RAM1024x4NRNW
SB_RAM2048x2
SB_RAM2048x2NR
SB_RAM2048x2NW
SB_RAM2048x2NRNW
Block RAM
Configuration
and Size
WADDR Port
Size (Bits)
WDATA Port
Size (Bits)
RADDR Port
Size (Bits)
RDATA Port
Size (Bits)
MASK Port
Size (Bits)
256x16 (4 k)
8 [7:0]
16 [15:0]
8 [7:0]
16 [15:0]
16 [15:0]
512x8 (4 k)
9 [8:0]
8 [7:0]
9 [8:0]
8 [7:0]
No Mask Port
1024x4 (4 k)
10 [9:0]
4 [3:0]
10 [9:0]
4 [3:0]
No Mask Port
2048x2 (4 k)
11 [10:0]
2 [1:0]
11 [10:0]
2 [1:0]
No Mask Port
Note: For iCE40 UltraPlus, the primitive name without “Nxx” uses rising-edge Read and Write clocks. “NR” uses rising-edge Write
clock and falling-edge Read clock. “NW” uses falling-edge Write clock and rising-edge Read clock. “NRNW” uses failing-edge clocks
on both Read and Write.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
15
iCE40 UltraPlus Family Data Sheet
Data Sheet
RAM Initialization and ROM Operation
If desired, the contents of the RAM can be pre-loaded during device configuration.
By preloading the RAM block during the chip configuration cycle and disabling the write controls, the sysMEM block
can also be utilized as a ROM.
Memory Cascading
Larger and deeper blocks of RAM can be created using multiple EBR sysMEM Blocks.
RAM4k Block
Figure 3.4 shows the 256x16 memory configurations and their input/output names. In all the sysMEM RAM modes, the
input data and addresses for the ports are registered at the input of the memory array.
Write Port
Read Port
WDATA[15:0]
RDATA[15:0]
MASK[15:0]
RADDR[7:0]
WADDR[7:0]
RAM4K
RAM Block
(256x16)
WE
RE
WCLKE
RCLKE
WCLK
RCLK
Figure 3.4. sysMEM Memory Primitives
Table 3.5 lists the EBR signals.
Table 3.5. EBR Signal Descriptions
Signal Name
Direction
WDATA[15:0]
Input
Write Data input.
MASK[15:0]
Input
WADDR[7:0]
Input
Masks write operations for individual data bit-lines.
0 – Write bit
1 – Do not write bit
Write Address input. Selects one of 256 possible RAM locations.
WE
Input
Write Enable input.
WCLKE
Input
Write Clock Enable input.
Input
Write Clock input. Default rising-edge, but with falling-edge option.
WCLK
Description
RDATA[15:0]
Output
Read Data output.
RADDR[7:0]
Input
Read Address input. Selects one of 256 possible RAM locations.
RE
Input
Read Enable input.
RCLKE
Input
Read Clock Enable input.
RCLK
Input
Read Clock input. Default rising-edge, but with falling-edge option.
For further information on the sysMEM EBR block, refer to Memory Usage Guide for iCE40 Devices (FPGA-TN-02002).
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
16
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
3.1.6. sysMEM Single Port RAM Memory (SPRAM)
The SPRAM block is implemented to be accessed only as single port. Each block of SPRAM is designed to be 16K x 16
(256 kbits) in size. See Figure 3.5.
SPRAM Data Width
The SPRAM is designed with fixed 16-bit data width. However, the block contains nibble mask control on the write
input that allows the user logic to operate the SPRAM as x4 or x8 with this control on the write side, and user logic to
select which nibble/byte in the read side.
SPRAM Initialization and ROM Operation
There is no pre-load into the SPRAM during device configuration, therefore, the SPRAM is not initialized after
configuration.
SPRAM Cascading
Deeper SPRAM can be created using multiple SPRAM blocks, up to four blocks (64K x 16)
SPRAM Power Modes
There are three power modes in the SPRAM that the users can select during normal operation. This reduces the SPRAM
block power when it Is not needed, allow lower power consumption in an always-on application. These modes are:
Standby Mode: SPRAM stops all activity, and SPRAM freezes in its current state. Memory contents are retained,
memory outputs are retained, and all register contents are retained.
Sleep Mode: SPRAM block is shut down on all peripheral circuit, except the memory core. Memory contents are
retained, memory outputs and register contents are clear and become unknown.
Power Off Mode: Power source to the SPRAM is disconnected. This is the lowest power state. Memory contents
are lost. Memory outputs are unknown.
DATAOUT [15:0]
MASKWREN [3:0]
WREN
MASKWREN [3:0]
WREN
CHIPSELECT
Single Port RAM Primitive
SB_SPRAM256KA
CLOCK
STANDBY
SLEEP
POWEROFFN
Figure 3.5. SPRAM Primitive
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
17
iCE40 UltraPlus Family Data Sheet
Data Sheet
Table 3.6. SPRAM Signal Descriptions
Signal Name
Direction
Description
ADDRESS[13:0]
Input
Address input
DATAIN[15:0]
MASKWREN[3:0]
WREN
CHIPSELECT
CLOCK
STANDY
Input
Input
Input
Input
Input
Input
Write Data input
Nibble WE control
Write Enable
Enable SPRAM
Clock input
Standby Mode
SLEEP
Input
Sleep Mode
Input
Switch off power source to SPRAM
POWEROFF
DATAOUT[15:0]
Output
Output Data
For further information on sysMEM SPRAM block, refer to iCE40 SPRAM Usage Guide (FPGA-TN-02022).
3.1.7. sysDSP
The iCE40 UltraPlus family provides an efficient sysDSP architecture that is very suitable for low-cost Digital Signal
Processing (DSP) functions for mobile applications. Typical functions used in these applications are Multiply,
Accumulate, and Multiply-Accumulate. The block can also be used for simple Add and Subtract functions.
iCE40 UltraPlus sysDSP Architecture Features
The iCE40 UltraPlus sysDSP supports many functions that include the following:
Single 16-bit x 16-bit Multiplier, or two independent 8-bit x 8-bit Multipliers
Optional independent pipeline control on Input Register, Output Register, and Intermediate Reg faster clock
performance
Single 32-bit Accumulator, or two independent 16-bit Accumulators
Single 32-bit, or two independent 16-bit Adder/Subtracter functions, registered or asynchronous
Cascadable to create wider Accumulator blocks
Figure 3.6 shows the block diagram of the sysDSP block. The block consists of the Multiplier section with a bypassable
Output register, Input Register, and Intermediate register between Multiplier and AC timing to achieve the highest
performance.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
18
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Input Registers
SIGNEXTOUT
CO
COCAS
Accumulator
0
1
Multiplier
Q [31:16]
1
16x 16 Pipeline
Registers
C1
R
8x 8
Q
0
D
B [15:8]
Q
8x 8
J
+
[7:0]
A [15:8]
0
D
+
Q
R
D
Q
1
8x 8
R
D
Q
H
R
C2
[31:16]
0
1
LCO
1
[15:0]
C7
LCOCA
S
Q [15:0
[7:0]
[7:0]
+
G
[15:8]
P [15:8]
OLADS
Y
0
[15 :0]
1
C5
P [7:0]
C 19
±
Z
S
R
1
0
1
8x 8=16
B
HLD
R
Q
0
HLD
[7:0]
B [15:0]
BHLD
16x 16=32
[15 :0]
1
0
D
B [7:0]
P [23:16]
K
C6
A [7:0]
0
C 11
L
HLD
8x 8
OHRST
OHHLD
OHLDA
HCI
C 10
16x 16
Pipeline
Register
[15:0]
8x 8 PowerSave
C 22
B [7:0]
P [31:24 ]
1
[15 :8]
IHRST
D
Q
2
3
D
0
O [15:0]
Lo
Z [15 ]
0
C 16
C 15
3
Q
1
R
OLRST
OLHLD
OLLDA
2
D
0
HLD
1
LCI
C 18
C 17
1
HLD
C3
1
ILRST
CLK
ENA
SIGNEXTIN
CICAS
C 20
0
3
BSGND=C24
2
C 21
ASGND=C23
1
R
0
D [15:0]
DHLD
Hi
C9
C8
3
C6
R
O [31:16]
2
[15:8]
[15 :8]
HLD
3
[15:0]
1
C4
R
A [7:0]
2
R
C 14
0
D
B [15:8]
1
HLD
C 13
A [15:8]
1
Q
1
3
Q
HLD
0
D
0
8x 8=16
2
0
D
P
X [15]
F
CSA
A
0
1
1
C0
[15:0]
A [15:0]
AHLD
X
C 12
R
±
1
Q
0
1
Q
HLD
0
D
CSA
C [15:0]
CHLD
OHADS
W
0
C
0
CI
Figure 3.6. sysDSP Functional Block Diagram (16-bit x 16-bit Multiply-Accumulate)
Table 3.7. Output Block Port Description
Signal
Primitive
Port Name
CLK
CLK
1
Input/
Output
Input
ENA
CE
1
Input
A[15:0]
A[15:0]
16
Input
B[15:0]
B[15:0]
16
Input
C[15:0]
C[15:0]
16
Input
D[15:0]
D[15:0]
16
Input
AHLD
AHOLD
1
Input
BHLD
BHOLD
1
Input
Width
Function
Clock Input. Applies to all clocked elements in the
sysDSP block
Clock Enable Input. Applies to all clocked elements
in the sysDSP block.
0 – Not enabled
1 – Enabled
Input to the A Register. Feeds the Multiplier or is a
direct input to the Adder Accumulator
Input to the B Register. Feeds the Multiplier or is a
direct input to the Adder Accumulator
Input to the C Register. It is a direct input to the
Adder Accumulator
Input to the D Register. It is a direct input to the
Adder Accumulator
A Register Hold.
0 – Update
1 – Hold
B Register Hold.
0 – Update
1 – Hold
Default
—
0 – Enabled
16'b0
16'b0
16'b0
16'b0
0 – Update
0 – Update
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
19
iCE40 UltraPlus Family Data Sheet
Data Sheet
Signal
Primitive
Port Name
CHLD
CHOLD
1
Input/
Output
Input
DHLD
DHOLD
1
Input
IHRST
IRSTTOP
1
Input
ILRST
IRSTBOT
1
Input
O[31:0]
O[31:0]
32
Output
OHHLD
OHOLDTOP
1
Input
OHRST
ORSTTOP
1
Input
OHLDA
OLOADTOP
1
Input
OHADS
ADDSUBTOP
1
Input
OLHLD
OHOLDBOT
1
Input
OLRST
ORSTBOT
1
Input
Width
Function
Default
C Register Hold.
0 – Update
1 – Hold
D Register Hold.
0 – Update
1 – Hold
Reset input to A and C input registers, and the
pipeline registers in the upper half of the Multiplier
Section.
0 – No reset
1 – Reset
Reset input to B and D input registers, and the
pipeline registers in the lower half of the Multiplier
Section. It also resets the Multiplier result pipeline
register.
0 – No reset
1 – Reset
Output of the sysDSP block. This output can be:
O[31:0] – 32-bit result of 16x16 Multiplier or
MAC
O[31:16] – 16-bit result of 8x8 upper half
Multiplier or MAC
O[15:0] – 16-bit result of 8x8 lower half Multiplier
or MAC
High-order (upper half) Accumulator Register Hold.
0 – Update
1 – Hold
Reset input to high-order (upper half) bits of the
Accumulator Register.
0 – No reset
1 – Reset
High-order (upper half) Accumulator Register
Accumulate/Load control.
0 – Accumulate, register is loaded with
Adder/Subtracter results
1 – Load, register is loaded with Input C or C
Register
High-order (upper half) Accumulator Add or
Subtract select.
0 – Add
1 – Subtract
Low-order (lower half) Accumulator Register Hold.
0 – Update
1 – Hold
Reset input to Low-order (lower half) bits of the
Accumulator Register.
0 –No reset
1 – Reset
0 – Update
0 – Update
0 – No reset
0 – No reset
—
0 – Update
0 – No reset
0–
Accumulate
0 – Add
0 – Update
0 – No reset
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
20
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Signal
Primitive
Port Name
Width
OLLDA
OLOADBOT
1
Input/
Output
Input
OLADS
ADDSUBBOT
1
Input
CICAS
ACCUMCI
1
Input
CI
COCAS
CO
CI
ACCUMCO
CO
1
1
1
Input
Output
Output
Low-order (lower half) Accumulator Register
Accumulate/Load control.
0 – Accumulate, register is loaded with
Adder/Subtracter results
1 – Load, register is loaded with Input C or C
Register
Low-order (lower half) Accumulator Add or
Subtract select.
0 – Add
1 – Subtract
Cascade Carry/Borrow input from previous sysDSP
block
Carry/Borrow input from lower logic tile
Cascade Carry/Borrow output to next sysDSP block
Carry/Borrow output to higher logic tile
SIGNEXTIN
SIGNEXTOUT
SIGNEXTIN
SIGNEXTOUT
1
1
Input
Output
Sign extension input from previous sysDSP block
Sing extension output to next sysDSP block
Function
Default
0–
Accumulate
0 – Add
—
—
—
—
—
—
The iCE40 UltraPlus sysDSP can support the following functions:
8-bit x 8-bit Multiplier
16-bit x 16-bit Multiplier
16-bit Adder/Subtracter
32-bit Adder/Subtracter
16-bit Accumulator
32-bit Accumulator
8-bit x 8-bit Multiply-Accumulate
16-bit x 16-bit Multiply-Accumulate
Figure 3.7 shows the path for an 8-bit x 8-bit Multiplier using the upper half of sysDSP block.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
21
iCE40 UltraPlus Family Data Sheet
Data Sheet
Input Registers
SIGNEXTOUT
CO
COCAS
Accumulator
0
1
Multiplier
Q [31 :16 ]
0
C[ 15 :0 ]
CHLD
D
Q
±
1
X
C12
C0
16 x 16 Pipeline
Registers
[ 15 :0 ]
Q
P
1
HLD
R
OHADS
W
0
C
0
0
D
1
1
Q
O [ 31 :16 ]
HLD
2
R
3
X [ 15 ]
0
A
0
F
A [ 15 :8 ]
0
C9
8 x 8 =16
[ 15 :0 ]
OHRST
OHHLD
OHLDA
2
Q
[15:8]
1
3
8 x8
J
0
D
+
C4
R
A [ 7 :0 ]
Q
[15:8]
HLD
+
C6
R
[15:8]
A [ 15 :8 ]
0
Q
[ 15 : 0 ]
BHLD
D
Q
1
R
HLD
Q
R
1
LCO
LCOCAS
Q [15:0]
+
G
[ 15 :8 ]
OLADS
Y
0
[7:0]
P [ 7: 0 ]
±
Z
C19
D
1
3
C 16
D
Low
C 15
OLRST
OLHLD
OLLDA
LCI
Q
O [ 15 :0 ]
2
Z [ 15 ]
3
D
1
0
2
DHLD
Q
HLD
R
1
D[ 15 :0 ]
0
0
8 x 8 = 16
R
0
S
R
1
[ 15 : 0 ]
1
C5
P [ 15 : 8 ]
B
C2
0
[ 15 : 0 ]
C7
[7:0]
0
8 x8
[ 31 : 16 ]
1
[7:0]
1
C6
A [ 7 :0 ]
D
Q
R
HLD
8 x8
D
CSA
D
H
0
HLD
K
B [ 7 :0 ]
B [ 7 :0 ]
16 x 16 =32
L
8 x 8 PowerSave
C 22
IHRST
Register
P [ 23 : 16 ]
CSA
8 x8
B [ 15 :0 ]
C 11
C 10
16 x 16
Pipeline
1
B [ 15 :8 ]
0
P [ 31 : 24 ]
[7:0]
[15 :0 ]
C13
C1
R
HCI
C14
D
B [ 15 :8 ]
2
1
3
Q
HLD
0
1
D
0
AHLD
1
A [ 15 :0 ]
High
C8
1
C 18
C 17
1
HLD
C3
ASGND=C23
1
2
0
3
0
1
BSGND=C24
CICAS
CI
ILRST
CLK
C20
C21
R
ENA
( 25 - FEB - 2012 )
SIGNEXTIN
Figure 3.7. sysDSP 8-bit x 8-bit Multiplier
Figure 3.8 shows the path for an 16-bit x 16-bit Multiplier using the upper half of sysDSP block.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
22
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Input Registers
SIGNEXTOUT
CO
COCAS
Accumulator
0
1
Multiplier
Q[31:16]
16x16 Pipeline
Registers
8x8
D
B[15:8]
Q
3
+
[7:0]
J
C22
D
Q
A[7:0]
B[15:0]
BHLD
D
Q
HLD
1
C2
R
8x8
R
[31:16]
[15:0]
0
1
LCO
C7
LCOCAS
Q[15:0
[7:0]
G
+
[15:8]
[15:0]
[7:0]
Q
Q
H
1
[7:0]
1
0
D
D
R
C6
R
0
HLD
[15:0]
HLD
B[7:0]
16x16=32
L
K
0
8x8
0
P[23:16]
8x8 PowerSave
A[15:8]
B[7:0]
C11
C10
16x16
Pipeline
Register
1
+
1
C5
P[15:8]
OLADS
Y
0
1
P[7:0]
C19
±
Z
0
1
8x8=16
B
0
0
1
2
R
3
O[15:0]
D
Low
OLRST
OLHLD
OLLDA
LCI
C18
C17
1
1
C20
0
3
C21
ASGND=23
BSGND=24
2
C3
1
R
Q
HLD
C16
0
HLD
D
C15
3
Q
R
0
2
D
S
Z[15]
1
D[15:0]
DHLD
High
OHRST
OHHLD
OHLDA
HCI
P[31:24]
[ 15:0]
[15:8]
IHRST
C9
2
[15:8]
C6
R
O[31:16]
C8
1
[15:8]
HLD
8x8
8x8=16
[ 15:0]
0
3
X[15]
1
C4
R
A[7:0]
2
R
C14
C1
R
Q
1
Q
HLD
C13
D
0
0
F
0
1
B[15:8]
HLD
D
3
A[15:8]
1
Q
A
0
Q
P
1
0
[15:0]
D
X
C12
0
A[15:0]
AHLD
±
1
C0
R
2
Q
HLD
CSA
D
1
CSA
C[15:0]
CHLD
OHADS
W
0
C
0
1
0
ILRST
CLK
ENA
SIGNEXTIN
CICAS CI
(25-FEB-2012)
Figure 3.8. DSP 16-bit x 16-bit Multiplier
3.1.8. sysI/O Buffer Banks
iCE40 UltraPlus devices have up to three I/O banks with independent VCCIO rails. The configuration SPI interface signals
are powered by SPI_VCCIO1. Refer to the Pin Information Summary table.
Programmable I/O (PIO)
The programmable logic associated with an I/O is called a PIO. The individual PIOs are connected to their respective
sysI/O buffers and pads. The PIOs are placed on the top and bottom of the devices.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
23
iCE40 UltraPlus Family Data Sheet
Data Sheet
VCCIO
I/O Bank 0 or 2
Voltage S upply
0 = Hi-Z
1 = Output
Enabled
Enabled ‘1’
Disabled ‘0’
Pull-up
OE
50 ns Dela y
Pull-up
Enable
50 ns Dela y
OUTCLK
50 ns Filter
50 ns Filter
5 PLB R ows
OUT
PAD
OUTCLK
iCEGATE
HOLD
HD
Latch inhibits
switching f or
power saving
IN
INC LK
Gxx pins optionally
connect directly to
an associated
GBUF global
buff er
Figure 3.9. I/O Bank and Programmable I/O Cell
The PIO contains three blocks: an input register block, output register block iCEGate™ and tri-state register block. To
save power, the optional iCEGate™ latch can selectively freeze the state of individual, non-registered inputs within an
I/O bank. Note that the freeze signal is common to the bank. These blocks can operate in a variety of modes along with
the necessary clock and selection logic.
Input Register Block
The input register blocks for the PIOs on all edges contain registers that can be used to condition high-speed interface
signals before they are passed to the device core.
Output Register Block
The output register block can optionally register signals from the core of the device before they are passed to the
sysI/O buffers.
Figure 3.10 shows the input/output register block for the PIOs.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
24
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
PIO Pair
CLOCK_ENABLE
OUTPUT_CLK
INPUT_CLK
(1,0)
LATCH_INPUT_VALUE
D_IN_1
D_IN_0
Pad
D_OUT_1
D_OUT_0
(1,0)
0
1
OUTPUT_ENABLE
(1,0)
LATCH_INPUT_VALUE
D_IN_1
D_IN_0
Pad
D_OUT_1
D_OUT_0
(1,0)
0
1
OUTPUT_ENABLE
= Statically defined by configuration program.
Figure 3.10. iCE I/O Register Block Diagram
Table 3.8. PIO Signal List
Pin Name
I/O Type
Description
OUTPUT_CLK
Input
Output register clock
CLOCK_ENABLE
Input
Clock enable
INPUT_CLK
Input
Input register clock
OUTPUT_ENABLE
Input
Output enable
D_OUT_0/1
Input
Data from the core
D_IN_0/1
LATCH_INPUT_VALUE
Output
Input
Data to the core
Latches/holds the Input Value
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
25
iCE40 UltraPlus Family Data Sheet
Data Sheet
3.1.9. sysI/O Buffer
Each I/O is associated with a flexible buffer referred to as a sysI/O buffer. These buffers are arranged around the
periphery of the device in groups referred to as banks. The sysI/O buffers allow users to implement a wide variety of
standards that are found in today’s systems with LVCMOS interfaces.
Typical I/O Behavior During Power-up
The internal power-on-reset (POR) signal is deactivated when VCC, SPI_VCCIO1 and VPP_2V5 reach the level defined in Table
4.4. After the POR signal is deactivated, the FPGA core logic becomes active. You must ensure that all VCCIO banks are
active with valid input logic levels to properly control the output logic states of all the I/O banks that are critical to the
application. The default configuration of the I/O pins in a device prior to configuration is tri-stated with a weak pull-up
to VCCIO. The I/O pins maintain the pre-configuration state until VCC, SPI_VCCIO1 and VPP_2V5 reach the defined levels. The
I/Os take on the software user-configured settings only after POR signal is deactivated and the device performs a
proper download/configuration. Unused I/Os are automatically blocked and the pull-up termination is disabled.
Supported Standards
The iCE40 UltraPlus sysI/O buffer supports both single-ended input/output standards, and used as differential
comparators. The buffer supports the LVCMOS 1.8 V, 2.5 V, and 3.3 V standards. The buffer has individually
configurable options for bus maintenance (weak pull-up or none).
Table 3.9 and Table 3.10 show the I/O standards (together with their supply and reference voltages) supported by the
iCE40 UltraPlus devices.
Differential Comparators
The iCE40 UltraPlus devices provide differential comparator on pairs of I/O pins. These comparators are useful in some
mobile applications. See the Pin Information Summary section to locate the corresponding paired I/Os with differential
comparators.
Table 3.9. Supported Input Standards
I/O Standard
VCCIO (Typical)
3.3 V
2.5 V
1.8 V
LVCMOS33
Yes
—
—
LVCMOS25
—
Yes
—
LVCMOS18
—
—
Yes
Single-Ended Interfaces
Table 3.10. Supported Output Standards
I/O Standard
VCCIO (Typical)
Single-Ended Interfaces
LVCMOS33
3.3 V
LVCMOS25
2.5 V
LVCMOS18
1.8 V
3.1.10. On-Chip Oscillator
The iCE40 UltraPlus devices feature two different frequency Oscillator. One is tailored for low-power operation that
runs at low frequency (LFOSC). Both Oscillators are controlled with internally generated current.
The LFOSC runs at nominal frequency of 10 kHz. The high frequency oscillator (HFOSC) runs at a nominal frequency of
48 MHz, divisible to 24 MHz, 12 MHz, or 6 MHz by user option. The LFOSC can be used to perform all always-on
functions, with the lowest power possible. The HFOSC can be enabled when the always-on functions detect a condition
that would need to wake up the system to perform higher frequency functions.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
26
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
3.1.11. User I2C IP
The iCE40 UltraPlus devices have two I2C IP cores. Either of the two cores can be configured either as an I2C master or
as an I2C slave. The pins for the I2C interface are not pre-assigned. User can use any General Purpose I/O pins.
In each of the two cores, there are options to delay the either the input or the output, or both, by 50 ns nominal, using
dedicated on-chip delay elements. This provides an easier interface with any external I2C components.
When the IP core is configured as master, it will be able to control other devices on the I2C bus through the preassigned pin interface. When the core is configured as the slave, the device will be able to provide I/O expansion to an
I2C Master. The I2C cores support the following functionality:
Master and Slave operation
7-bit and 10-bit addressing
Multi-master arbitration support
Clock stretching
Up to 400 kHz data transfer speed
General Call support
Optionally delaying input or output data, or both
Optional filter on SCL input
For further information on the User I2C, refer to iCE40 SPI/I2C Hardened IP Usage Guide (FPGA-TN-02011).
3.1.12. User SPI IP
The iCE40 UltraPlus devices have two SPI IP cores. The pins for the SPI interface are not pre-assigned. User can use any
General Purpose I/O pins. Both SPI IP cores can be configured as a SPI master or as a slave. When the SPI IP core is
configured as a master, it controls the other SPI enabled devices connected to the SPI Bus. When SPI IP core is
configured as a slave, the device will be able to interface to an external SPI master.
The SPI IP core supports the following functions:
Configurable Master and Slave modes
Full-Duplex data transfer
Mode fault error flag with CPU interrupt capability
Double-buffered data register
Serial clock with programmable polarity and phase
LSB First or MSB First Data Transfer
For further information on the User SPI, refer to iCE40 SPI/I2C Hardened IP Usage Guide (FPGA-TN-02011).
3.1.13. RGB High Current Drive I/O Pins
The iCE40 UltraPlus family devices offer multiple high current LED drive outputs in each device in the family to allow
the iCE40 UltraPlus product to drive LED signals directly on mobile applications.
There are three outputs on each device that can sink up to 24 mA current. These outputs are open-drain outputs, and
provides sinking current to an LED connecting to the positive supply. These three outputs are designed to drive the RBG
LEDs, such as the service LED found in a lot of mobile devices. This RGB drive current is user programmable from 4 mA
to 24 mA, in increments of 4 mA. This output functions as General Purpose I/O with open-drain when the high current
drive is not needed.
3.1.14. RGB PWM IP
To provide an easier usage of the RGB high current drivers to drive RGB LED, a Pulse-Width Modulator IP can be used in
the user design. This PWM IP provides the flexibility for user to dynamically change the modulation width of each of
the RGB LED driver, which changes the color. Also, the user can dynamically change the settings on the ON-time
duration, OFF-time duration, and ability to turn the LED lights on and off gradually with user set breath-on and breathoff time.
For additional information on the PWM IP, refer to iCE40 LED Driver Usage Guide (FPGA-TN-02021).
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
27
iCE40 UltraPlus Family Data Sheet
Data Sheet
3.1.15. Non-Volatile Configuration Memory
All iCE40 UltraPlus devices provide a Non-Volatile Configuration Memory (NVCM) block which can be used to configure
the device.
For more information on the NVCM, refer to iCE40 Programming and Configuration (FPGA-TN-02001).
3.2. iCE40 UltraPlus Programming and Configuration
This section describes the programming and configuration of the iCE40 UltraPlus family.
3.2.1. Device Programming
The NVCM memory can be programmed through the SPI port. The SPI port is located in Bank 1, using SPI_VCCIO1 power
supply.
3.2.2. Device Configuration
There are various ways to configure the Configuration RAM (CRAM), using SPI port, including:
From a SPI Flash (Master SPI mode)
System microprocessor to drive a Serial Slave SPI port (SSPI mode)
For more details on configuring the iCE40 UltraPlus, refer to iCE40 Programming and Configuration (FPGA-TN-02001).
3.2.3. Power Saving Options
The iCE40 UltraPlus devices feature iCEGate and PLL low power mode to allow users to meet the static and dynamic
power requirements of their applications. Table 3.11 describes the function of these features.
Table 3.11. iCE40 UltraPlus Power Saving Features Description
Device Subsystem
Feature Description
PLL
When LATCHINPUTVALUE is enabled, puts the PLL into low-power mode; PLL output held static at last
input clock value.
To save power, the optional iCEGate latch can selectively freeze the state of individual, non-registered
inputs within an I/O bank. Registered inputs are effectively frozen by their associated clock or clockenable control.
iCEGate
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
28
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
4. DC and Switching Characteristics
4.1. Absolute Maximum Ratings
Table 4.1. Absolute Maximum Ratings
Parameter
Min
Max
Unit
Supply Voltage VCC
–0.5
1.42
V
Output Supply Voltage VCCIO
–0.5
3.60
V
NVCM Supply Voltage VPP_2V5
–0.5
3.60
V
PLL Supply Voltage VCCPLL
–0.5
1.42
V
I/O Tri-state Voltage Applied
–0.5
3.60
V
Dedicated Input Voltage Applied
–0.5
3.60
V
Storage Temperature (Ambient)
–65
150
°C
Junction Temperature (TJ)
–65
125
°C
Notes:
Stress above those listed under the Absolute Maximum Ratings may cause permanent damage to the device. Functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is
not implied.
Compliance with the Thermal Management document is required.
All voltages referenced to GND.
4.2. Recommended Operating Conditions
Table 4.2. Recommended Operating Conditions
Symbol
Parameter
VCC1
Core Supply Voltage
VPP_2V5
VPP_2V5 NVCM
Programming and
Operating Supply Voltage
Min
Max
Unit
1.14
1.26
V
Slave SPI Configuration
1.714
3.46
V
Master SPI Configuration
2.30
3.46
V
Configuration from NVCM
NVCM Programming
VCCIO_0, SPI_VCCIO1, VCCIO_2
2.30
2.30
1.71
1.14
0
–40
10.00
3.46
3.00
3.46
1.26
85
100
30.00
V
V
V
V
°C
°C
°C
VCCIO1, 2, 3
I/O Driver Supply Voltage
VCCPLL
PLL Supply Voltage
tJCOM
Junction Temperature Commercial Operation
tJIND
Junction Temperature, Industrial Operation
tPROG
Junction Temperature NVCM Programming
Notes:
1. Like power supplies must be tied together if they are at the same supply voltage and they meet the power up sequence
requirement. See the Power-up Supply Sequence section. VCC and VCCPLL are recommended to be tied together to the same
supply with an RC-based noise filter between them. Refer to iCE40 Hardware Checklist (FPGA-TN-02006).
2. See recommended voltages by I/O standard in subsequent table.
3. VCCIO pins of unused I/O banks should be connected to the VCC power supply on boards.
4. VPP_2V5 can, optionally, be connected to a 1.8 V (+/–5%) power supply in Slave SPI Configuration modes subject to the condition
that none of the HFOSC/LFOSC and RGB LED driver features are used. Otherwise, VPP_2V5 must be connected to a power supply
with a minimum 2.30 V level.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
29
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.3. Power Supply Ramp Rates
Table 4.3. Power Supply Ramp Rates
Symbol
Parameter
Min
Max
Unit
tRAMP
Power supply ramp rates for all power supplies
0.6
10
V/ms
Notes:
Assumes monotonic ramp rates.
Power up sequence must be followed. See the Power-up Supply Sequence section below.
4.4. Power-On Reset
All iCE40 UltraPlus devices have on-chip Power-On-Reset (POR) circuitry to ensure proper initialization of the device.
Only three supply rails are monitored by the POR circuitry as follows: (1) VCC, (2) SPI_VCCIO1 and (3) VPP_2V5. All other
supply pins have no effect on the power-on reset feature of the device. Note that all supply voltage pins must be
connected to power supplies for normal operation (including device configuration).
4.5. Power-up Supply Sequence
It is recommended to bring up the power supplies in the following order. Note that there is no specified timing delay
between the power supplies, however, there is a requirement for each supply to reach a level of 0.5 V, or higher,
before any subsequent power supplies in the sequence are applied.
1.
VCC and VCCPLL should be the first two supplies to be applied. Note that these two supplies can be tied together
subject to the recommendation to include a RC-based noise filter on the VCCPLL. Refer to iCE40 Hardware Checklist
(FPGA-TN-02006).
2.
SPI_VCCIO1 should be the next supply, and can be applied any time after the previous supplies (VCC and VCCPLL) have
reached as level of 0.5 V or higher.
3.
VPP_2V5 should be the next supply, and can be applied any time after previous supplies (VCC, VCCPLL and SPI_VCCIO1)
have reached a level of 0.5 V or higher.
4.
Other Supplies (VCCIO0 and VCCIO2) do not affect device power-up functionality, and they can be applied any time
after the initial power supplies (VCC and VCCPLL) have reached a level of 0.5 V or greater. There is no power down
sequence required. However, when partial power supplies are powered down, it is required the above sequence to
be followed when these supplies are re-powered up again.
4.6. External Reset
When all power supplies have reached their minimum operating voltage defined in Table 4.2, it is required to either
keep CRESET_B LOW, or toggle CRESET_B from HIGH to LOW, for a duration of tCRESET_B, and release it to go HIGH, to
start configuration download from either the internal NVCM or the external Flash memory. Figure 4.1 shows Power-Up
sequence when SPI_VCCIO1 and VPP_2V5 are not connected together, and the CRESET_B signal triggers configuration
download. Figure 4.2 shows when SPI_VCCIO1 and VPP_2V5 connected together. All power supplies should be powered
up during configuration. Before and during configuration, the I/Os are held in tri-state. I/Os are released to user
functionality once the device has finished configuration.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
30
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Figure 4.1. Power Up Sequence with SPE_VCCIO1 and VPP_2V5 Not Connected Together
Figure 4.2. Power Up Sequence with All Supplies Connected Together to 1.8 V
4.7. Power-On-Reset Voltage Levels
Table 4.4. Power-On-Reset Voltage Levels
Symbol
Parameter
VPORUP
Power-On-Reset ramp up trip point (circuit
monitoring VCC, SPI_VCCIO1, and VPP_2V5)
VPORDN
Power-On-Reset ramp down trip point (circuit
monitoring VCC, SPI_VCCIO1, and VPP_2V5)
Min
Max
Unit
VCC
0.62
0.92
V
SPI_VCCIO1
0.87
1.50
V
VPP_2V5
0.90
1.53
V
VCC
—
0.79
V
SPI_VCCIO1
—
1.50
V
VPP_2V5
—
1.53
V
Note: These POR trip points are only provided for guidance. Device operation is only characterized for power supply voltages
specified under recommended operating conditions.
4.8. ESD Performance
Please contact Lattice Semiconductor for additional information.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
31
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.9. DC Electrical Characteristics
Over recommended operating conditions.
Table 4.5. DC Electrical Characteristics
Symbol
Parameter
Condition
Min
Typ
Max
Unit
Input or I/O Leakage
0 V < VIN < VCCIO + 0.2 V
—
—
±10
µA
I/O Capacitance, excluding
LED Drivers2
VCCIO = 3.3 V, 2.5 V, 1.8 V
VCC = Typ, VIO = 0 to VCCIO + 0.2 V
C1
—
6
—
pf
C2
Global Input Buffer
Capacitance2
VCCIO = 3.3 V, 2.5 V, 1.8 V
VCC = Typ, VIO = 0 to VCCIO + 0.2 V
—
6
—
pf
C3
RGB Pin Capacitance2
VCC = Typ, VIO = 0 to 3.5 V
—
15
—
pf
VCC = Typ, VIO = 0 to 3.5 V
—
53
—
pf
VCCIO = 1.8 V, 2.5 V, 3.3 V
—
200
—
mV
VCCIO = 1.8 V, 0 ≤ VIN ≤ 0.65 * VCCIO
−3
—
−31
µA
VCCIO = 2.5 V, 0 ≤ VIN ≤ 0.65 * VCCIO
−8
—
−72
µA
VCCIO = 3.3 V, 0 ≤ VIN ≤ 0.65 * VCCIO
−11
—
−128
µA
1, 3, 4
IIL, IIH
Capacitance2
C4
IRLED Pin
VHYST
Input Hysteresis
Internal PIO Pull-up Current
IPU
Notes:
1. Input or I/O leakage current is measured with the pin configured as an input or as an I/O with the output driver tri-stated. It is
not measured with the output driver active. Internal pull-up resistors are disabled.
2. TJ 25 oC, f = 1.0 MHz.
3. Refer to VIL and VIH in Table 4.13.
4. Input pins are clamped to VCCIO and GND by a diode. When input is higher than VCCIO or lower than GND, the Input Leakage
current will be higher than the IIL and IIH.
4.10. Supply Current
Table 4.6. Supply Current
Typ
VCC =1.2 V
75
Symbol
Parameter
Unit
ICCSTDBY
Core Power Supply Static Current
IPP2V5STDBY
VPP_2V5 Power Supply Static Current
0.55
µA
ISPI_VCCIO1STDBY
SPI_VCCIO1 Power Supply Static Current
0.5
µA
ICCIOSTDBY
VCCIO Power Supply Static Current
0.5
µA
ICCPEAK
Core Power Supply Startup Peak Current
12
mA
IPP_2V5PEAK
VPP_2V5 Power Supply Startup Peak Current
2.5
mA
ISPI_VCCIO1PEAK
SPI_VCCIO1 Power Supply Startup Peak Current
9.0
mA
ICCIOPEAK
VCCIO Power Supply Startup Peak Current
2.0
mA
µA
Notes:
Assumes blank pattern with the following characteristics: all outputs are tri-stated, all inputs are configured as LVCMOS and
held at VCCIO or GND, on-chip PLL is off. For more detail with your specific design, use the Power Calculator tool. Power specified
with master SPI configuration mode. Other modes may be up to 25% higher.
Frequency = 0 MHz.
TJ = 25 °C, power supplies at nominal voltage, on devices processed in nominal process conditions.
Does not include pull-up.
Startup Peak Currents are measured with decoupling capacitances of 0.1 uF, 10 nF, and 1 nF to the power supply. Higher
decoupling capacitance causes higher current.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
32
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.11. User I2C Specifications
Table 4.7. User I2C Specifications
Symbol
Parameter
fSCL
Maximum SCL clock frequency
tHI
tLO
Spec (STD Mode)
Spec (FAST Mode)
Unit
Min
Typ
Max
Min
Typ
Max
—
—
100
—
—
400
kHz
SCL clock HIGH Time
4
—
—
0.6
—
—
µs
SCL clock LOW Time
4.7
—
—
1.3
—
—
µs
tSU,DAT
Setup time (DATA)
250
—
—
100
—
—
ns
tHD,DAT
Hold time (DATA)
0
—
—
0
—
—
ns
tSU,STA
Setup time (START condition)
4.7
—
—
0.6
—
—
µs
tHD,STA
Hold time (START condition)
4
—
—
0.6
—
—
µs
tSU,STO
Setup time (STOP condition)
4
—
—
0.6
—
—
µs
tBUF
Bus free time between STOP and START
4.7
—
—
1.3
—
—
µs
tCO,DAT
SCL LOW to DATAOUT valid
—
—
3.4
—
—
0.9
µs
4.12. I2C 50 ns Delay
Table 4.8. I2C 50 ns Delay
Symbol
Parameter
TDELAY
Delay through 50 ns Delay Block
Spec
Min
Typ
Max
—
50
—
Unit
ns
4.13. I2C 50 ns Filter
Table 4.9. I2C 50 ns Filter
Symbol
Parameter
TFILTER-H
TFILTER-L
Spec
Unit
Min
Typ
Max
HIGH Pulse Filter through 50 ns Filter Block
—
50
—
ns
LOW Pulse Filter through 50 ns Filter Block
—
50
—
ns
Min
Typ
Max
Unit
—
—
45
MHz
4.14. User SPI Specifications
Table 4.10. User SPI Specifications
Symbol
Parameter
fMAX
Maximum SCK clock frequency
Notes:
All setup and hold time parameters on external SPI interface are design-specific and, therefore, generated by the Lattice Design
Software too. These parameters include the following:
tSUmaster master Setup Time (master mode)
tHOLDmaster master Hold time (master mode)
tSUslave
slave Setup Time (slave mode)
tHOLDslave slave Hold time (slave mode)
tSCK2OUT SCK to Out Delay (slave mode)
The SCLK duty cycle needs to be specified in the Lattice Design Software as a timing constraint in order to ensure proper timing
check on SCLK HIGH and LOW (tHI, tLO) time.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
33
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.15. Internal Oscillators (HFOSC, LFOSC)
Table 4.11. Internal Oscillators (HFOSC, LFOSC)
Parameter
Symbol
Spec/Recommended
Parameter Description
Conditions
Min
Typ
Max
Unit
Commercial Temp
HFOSC clock frequency (tJ = 0 °C–85 °C)
–10%
48
10%
MHz
Industrial Temp
HFOSC clock frequency (tJ = –40 °C–100 °C)
–20%
48
20%
MHz
—
LFOSC CLKK clock frequency
–10%
10
10%
kHz
Commercial Temp
HFOSC Duty Cycle (tJ = 0 °C–85 °C)
45
50
55
%
Industrial Temp
HFOSC Duty Cycle (tJ = –40 °C–100 °C)
40
50
60
%
DCHCLKLF
—
LFOSC Duty Cycle (Clock High Period)
45
50
55
%
Tsync_on
—
Oscillator output synchronizer delay
—
—
5
Cycles
Tsync_off
—
Oscillator output disable delay
—
—
5
Cycles
fCLKHF
fCLKLF
DCHCLKHF
Note: Glitchless enabling and disabling OSC clock outputs.
4.16. sysI/O Recommended Operating Conditions
Table 4.12. sysI/O Recommended Operating Conditions
VCCIO (V)
Standard
Min
Typ
Max
LVCMOS 3.3
3.14
3.3
3.46
LVCMOS 2.5
2.37
2.5
2.62
LVCMOS 1.8
1.71
1.8
1.89
4.17. sysI/O Single-Ended DC Electrical Characteristics
Table 4.13. sysI/O Single-Ended DC Electrical Characteristics
Input/Output
Standard
LVCMOS 3.3
LVCMOS 2.5
LVCMOS 1.8
VIL
Min (V)
–0.3
–0.3
–0.3
VIH
Max (V)
0.8
0.7
0.35 VCCIO
Min (V)
2.0
1.7
0.65 VCCIO
Max (V)
VCCIO+0.2 V
VCCIO+0.2 V
VCCIO+0.2 V
VOL Max
(V)
VOH Min
0.4
(V)
IOL
(mA)
IOH Max
(mA)
VCCIO − 0.4
8
–8
0.2
VCCIO − 0.2
0.1
–0.1
0.4
VCCIO − 0.4
6
–6
0.2
VCCIO − 0.2
0.1
–0.1
0.4
VCCIO − 0.4
4
–4
0.2
VCCIO − 0.2
0.1
–0.1
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
34
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.18. Differential Comparator Electrical Characteristics
Table 4.14. Differential Comparator Electrical Characteristics
Parameter
Symbol
VREF
Parameter Description
Test Conditions
Min
Max
Unit
Reference Voltage to compare, on VINM
VCCIO = 2.5 V
0.25
VCCIO - 0.25 V
V
VDIFFIN_H
Differential input HIGH (VINP - VINM)
VCCIO = 2.5 V
250
—
mV
VDIFFIN_L
Differential input LOW (VINP - VINM)
VCCIO = 2.5 V
—
–250
mV
IIN
Input Current, VINP and VINM
VCCIO = 2.5 V
–10
10
µA
4.19. Typical Building Block Function Performance
4.19.1. Pin-to-Pin Performance (LVCMOS25)
Table 4.15. Pin-to-Pin Performance (LVCMOS25)
Function
Timing
Unit
16-Bit Decoder
16.5
ns
4:1 Mux
18.0
ns
16:1 Mux
19.5
ns
Basic Functions
Notes:
The above timing numbers are generated using the Lattice Design Software tool. Exact performance may vary with device and
tool version. The tool uses internal parameters that have been characterized but are not tested on every device.
Using a VCC of 1.14 V at Junction Temperature 85 °C.
4.19.2. Register-to-Register Performance
Table 4.16. Register-to-Register Performance
Function
Timing
Unit
16:1 Mux
110
MHz
16-Bit Adder
100
MHz
16-Bit Counter
100
MHz
64-Bit Counter
40
MHz
150
MHz
Basic Functions
Embedded Memory Functions
256 x 16 Pseudo-Dual Port RAM
Notes:
The above timing numbers are generated using the Lattice Design Software tool. Exact performance may vary with device and
tool version. The tool uses internal parameters that have been characterized but are not tested on every device.
Under worst case operating conditions.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
35
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.20. sysDSP Timing
Over recommended operating conditions.
Table 4.17. sysDSP Timing
Parameter
Description
Min
Max
Unit
fMAX8x8SMULT
Max frequency signed MULT8x8 bypassing pipeline register
—
50
MHz
fMAX16x16SMULT
Max frequency signed MULT16x16 bypassing pipeline register
—
50
MHz
Min
Max
Unit
70
—
MHz
4.21. SPRAM Timing
Over recommended operating conditions.
Table 4.18. Single Port RAM Timing
Parameter
Description
fMAXSRAM
Max frequency SPRAM (4/8/16-bit Read and Write)
4.22. Derating Logic Timing
Logic timing provided in the following sections of the data sheet and the Lattice design tools are worst case numbers in
the operating range. Actual delays may be much faster. Lattice design tools can provide logic timing numbers at a
particular temperature and voltage.
4.23. Maximum sysI/O Buffer Performance
Table 4.19. Maximum sysI/O Buffer Performance
I/O Standard
Max Speed
Unit
LVCMOS33
250
MHz
LVCMOS25
250
MHz
LVCMOS18
250
MHz
LVCMOS33
250
MHz
LVCMOS25
250
MHz
LVCMOS18
155
MHz
LVCMOS12
70
MHz
Inputs
Outputs
Note: Measured with a toggling pattern.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
36
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.24. iCE40 UltraPlus Family Timing Adders
Over recommended commercial operating conditions.
Table 4.20. iCE40 UltraPlus Family Timing Adders
Buffer Type
Description
Timing (Typ)
Units
Input Adjusters
LVCMOS33
LVCMOS, VCCIO = 3.3 V
0.18
ns
LVCMOS25
LVCMOS, VCCIO = 2.5 V
0
ns
LVCMOS18
LVCMOS, VCCIO = 1.8 V
0.19
ns
LVCMOS33
LVCMOS, VCCIO = 3.3 V
–0.12
ns
LVCMOS25
LVCMOS, VCCIO = 2.5 V
0
ns
LVCMOS18
LVCMOS, VCCIO = 1.8 V
1.32
ns
LVCMOS12
LVCMOS, VCCIO = 1.2 V
5.38
ns
Output Adjusters
Notes:
Timing adders are relative to LVCMOS25 and characterized but not tested on every device.
LVCMOS timing measured with the load specified in the Switching Test Conditions table.
Commercial timing numbers are shown.
4.25. iCE40 UltraPlus External Switching Characteristics
Over recommended commercial operating conditions.
Table 4.21. iCE40 UltraPlus External Switching Characteristics
Parameter
Description
Device
Clocks
Global Clock
fMAX_GBUF
Frequency for Global Buffer Clock network
All Devices
tW_GBUF
Clock Pulse Width for Global Buffer
All Devices
tISKEW_GBUF
Global Buffer Clock Skew Within a Device
All Devices
Pin-LUT-Pin Propagation Delay
Best case propagation delay through one
tPD
All Devices
LUT logic
General I/O Pin Parameters (Using Global Buffer Clock without PLL)*
tSKEW_IO
Data bus skew across a bank of IOs
All Devices
tCO
Clock to Output – PIO Output Register
All Devices
tSU
Clock to Data Setup – PIO Input Register
All Devices
tH
Clock to Data Hold – PIO Input Register
All Devices
General I/O Pin Parameters (Using Global Buffer Clock with PLL)
tCOPLL
Clock to Output – PIO Output Register
All Devices
tSUPLL
Clock to Data Setup – PIO Input Register
All Devices
tHPLL
Clock to Data Hold – PIO Input Register
All Devices
*Note: All the data is from the worst case.
Min
Max
Unit
—
2
—
185
—
530
MHz
ns
ps
—
9.0
ns
—
—
−0.5
5.55
510
10.0
—
—
ps
ns
ns
ns
—
7.3
−1.1
2.4
—
—
ns
ns
ns
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
37
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.26. sysCLOCK PLL Timing
Over recommended operating conditions.
Table 4.22. sysCLOCK PLL Timing
Parameter
Descriptions
Conditions
Input Clock Frequency (REFERENCECLK,
EXTFEEDBACK)
Output Clock Frequency (PLLOUT)
fIN
fOUT
PLL VCO Frequency
fVCO
3
Phase Detector Input Frequency
fPFD
AC Characteristics
tDT
Output Clock Duty Cycle
tPH
Output Phase Accuracy
Output Clock Period Jitter
tOPJIT1, 5, 6
Output Clock Cycle-to-Cycle Jitter
Output Clock Phase Jitter
—
Unit
10
133
MHz
16
275
MHz
—
—
533
10
1066
133
MHz
MHz
—
—
fOUT >= 100 MHz
fOUT < 100 MHz
fOUT >= 100 MHz
fOUT < 100 MHz
fPFD >= 25 MHz
40
—
—
—
—
—
—
—
60
±12
450
0.05
750
0.10
275
0.05
%
deg
ps p-p
UIPP
ps p-p
UIPP
ps p-p
UIPP
1.33
—
—
50
ns
µs
—
—
—
—
50
1000
0.02
500
ns
ps p-p
UIPP
ns
fPFD < 25 MHz
Output Clock Pulse Width
At 90% or 10%
tLOCK2, 3
tUNLOCK
PLL Lock-in Time
PLL Unlock Time
tIPJIT4
Input Clock Period Jitter
—
—
fPFD ≥ 20 MHz
fPFD < 20 MHz
—
LATCHINPUTVALUE LOW to PLL Stable
Max
—
tW
tSTABLE3
Min
3
tSTABLE_PW
LATCHINPUTVALUE Pulse Width
—
100
—
ns
tRST
RESET Pulse Width
—
10
—
ns
tRSTREC
RESET Recovery Time
—
10
—
µs
tDYNAMIC_WD
DYNAMICDELAY Pulse Width
—
100
—
VCO Cycles
Notes:
1. Period jitter sample is taken over 10,000 samples of the primary PLL output with a clean reference clock. Cycle-to-cycle jitter is
taken over 1000 cycles. Phase jitter is taken over 2000 cycles. All values per JESD65B.
2. Output clock is valid after tLOCK for PLL reset and dynamic delay adjustment.
3. At minimum fPFD. As the fPFD increases the time will decrease to approximately 60% the value listed.
4. Maximum limit to prevent PLL unlock from occurring. Does not imply the PLL will operate within the output specifications listed
in this table.
5. The jitter values will increase with loading of the PLD fabric and in the presence of SSO noise.
4.27. SPI Master or NVCM Configuration Time
Table 4.23. SPI Master or NVCM Configuration Time1, 2
Symbol
tCONFIG
Parameter
POR/CRESET_B to Device I/O Active
Conditions
Max
Unit
All devices – Low Frequency (Default)
140
ms
All devices – Medium frequency
50
ms
All devices – High frequency3
Notes:
1. Assumes sysMEM Block is initialized to an all zero pattern if they are used.
2. The NVCM download time is measured with a fast ramp rate starting from the maximum voltage of POR trip point.
3. High frequency is supported only on SPI Master.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
38
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.28. sysCONFIG Port Timing Specifications
Over recommended operating conditions.
Table 4.24. sysCONFIG Port Timing Specifications
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Minimum CRESET_B LOW pulse width
required to restart configuration, from
falling edge to rising edge
—
200
—
—
ns
Number of configuration clock cycles after
CDONE goes HIGH before the PIO pins are
activated
—
49
—
—
Clock
Cycles
Minimum time from a rising edge on
CRESET_B until the first SPI WRITE
operation, first SPI_SCK clock. During this
time, the iCE40 UltraPlus device is clearing
its internal configuration memory
—
1200
—
—
µs
Read1
1
—
—
15
25
—
MHz
MHz
All Configuration Mode
tCRESET_B
tDONE_IO
Slave SPI
tCR_SCK
fMAX
CCLK clock frequency
Write
tCCLKH
CCLK clock pulsewidth HIGH
—
20
—
—
ns
tCCLKL
CCLK clock pulsewidth LOW
—
20
—
—
ns
tSTSU
CCLK setup time
—
12
—
—
ns
tSTH
CCLK hold time
—
12
—
—
ns
tSTCO
CCLK falling edge to valid output
—
13
—
—
ns
MCLK clock frequency
Low Frequency
(Default)
Medium Frequency2
Master SPI3
fMCLK
High
Frequency2
7.0
12.0
17.0
MHz
21.0
33.0
45.0
MHz
33.0
53.0
71.0
MHz
tMCLK
CRESET_B HIGH to first MCLK edge
—
1200
—
—
µs
tSU
CCLK setup time
—
6.16
—
—
ns
tHD
CCLK hold time
—
1
—
—
ns
Notes:
1. Supported with 1.2 V VCC and at 25 °C.
2. Extended range fMAX Write operations support up to 53 MHz with 1.2 V VCC and at 25 °C.
3. tSU and tHD timing must be met for all MCLK frequency choices.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
39
iCE40 UltraPlus Family Data Sheet
Data Sheet
4.29. RGB LED Drive
Table 4.25. RGB LED
Symbol
Parameter
Min
Max
Unit
ILED_ACCURACY
ILED_MATCH
RGB0, RGB1, RGB2 Sink Current Accuracy to selected current @ VLEDOUT >= 0.5 V
RGB0, RGB1, RGB2 Sink Current Matching among the 3 outputs @ VLEDOUT >= 0.5
V
–12
–5
+12
+5
%
%
4.30. Switching Test Conditions
Figure 4.3 shows the output test load that is used for AC testing. The specific values for resistance, capacitance,
voltage, and other test conditions are listed in Table 4.26.
VT
R1
Test Point
DUT
CL
Figure 4.3. Output Test Load, LVCMOS Standards
Table 4.26. Test Fixture Required Components, Non-Terminated Interfaces
Test Condition
R1
CL
LVCMOS settings (L ≥ H, H ≥ L)
∞
0 pF
Timing Reference
VT
LVCMOS 3.3 = 1.5 V
—
LVCMOS 2.5 = VCCIO/2
—
LVCMOS 1.8 = VCCIO/2
—
LVCMOS 3.3 (Z ≥ H)
1.5 V
VOL
LVCMOS 3.3 (Z ≥ L)
1.5 V
VOH
Other LVCMOS (Z ≥ H)
VCCIO/2
VOL
Other LVCMOS (Z ≥ L)
188
0 pF
VCCIO/2
VOH
LVCMOS (H ≥ Z)
VOH – 0.15 V
VOL
LVCMOS (L ≥ Z)
VOL – 0.15 V
VOH
Note: Output test conditions for all other interfaces are determined by the respective standards.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
40
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
5. Pinout Information
5.1. Signal Descriptions
5.1.1. Power Supply Pins
Signal Name
VCC
VCCIO_0, SPI_VCCIO1, VCCIO_2
VPP_2V5
VCCPLL
GND
GND_LED
Function
Power
Power
Power
Power
GROUND
GROUND
I/O
—
—
—
—
—
—
Description
Core Power Supply
Power for I/Os in Bank 0, 1, and 2.
Power for NVCM programming and operations.
Power for PLL.
Ground
Ground for LED drivers. Should connect to GND on board.
5.1.2. Configuration Pins
Signal Name
General I/O
CRESET_B
Shared
Function
—
IOB_xxx
CDONE
Function
I/O
Configuration
I
Configuration
I/O
General I/O
I/O
Description
Configuration Reset, active LOW. No internal pull-up resistor.
Either actively driven externally or connect an 10 kΩ pull-up to
SPI_VCCIO1.
Configuration Done. Includes a weak pull-up resistor to
SPI_VCCIO1.
In user mode, after configuration, this pin can be programmed
as general I/O in user function. In 30-pin WLCSP, this pin
connects to IOB_12a, which also is shared as global signal G4
in user mode.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
41
iCE40 UltraPlus Family Data Sheet
Data Sheet
5.1.3. Configuration SPI Pins
Signal Name
General I/O
IOB_34a
IOB_32a
Shared
Function
SPI_SCK
SPI_SO
Function
I/O
Description
Configuration
I/O
General I/O
I/O
This pin is shared with device configuration. During configuration:
In Master SPI mode, this pin outputs the clock to external SPI
memory.
In Slave SPI mode, this pin inputs the clock from external
processor.
In user mode, after configuration, this pin can be programmed as
general I/O in user function.
This pin is shared with device configuration. During configuration:
In Master SPI mode, this pin outputs the command data to
external SPI memory.
In Slave SPI mode, this pin connects to the MISO pin of the
external processor.
In user mode, after configuration, this pin can be programmed as
general I/O in user function.
This pin is shared with device configuration. During configuration:
In Master SPI mode, this pin receives data from external SPI
memory.
In Slave SPI mode, this pin connects to the MOSI pin of the
external processor.
In user mode, after configuration, this pin can be programmed as
general I/O in user function.
This pin is shared with device configuration. During configuration:
In Master SPI mode, this pin outputs to the external SPI memory.
In Slave SPI mode, this pin inputs CSN from the external
processor.
In user mode, after configuration, this pin can be programmed as
general I/O in user function.
Configuration
General I/O
IOB_33b
IOB_35b
SPI_SI
SPI_SS
Configuration
Output
I/O
Input
General I/O
I/O
Configuration
I/O
General I/O
I/O
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
42
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
5.1.4. Global Pins
Signal Name
General I/O
IOT_46b
IOT_45a
IOB_25b
IOB_12a
IOB_11b
IOB_3b
Shared
Function
G0
G1
G3
G4
G5
G6
Function
I/O
Description
General I/O
I/O
Global
Input
General I/O
I/O
Global
Input
General I/O
I/O
Global
Input
General I/O
I/O
Global
Input
General I/O
I/O
Global
Input
General I/O
I/O
Global
Input
In user mode, after configuration, this pin can be
programmed as general I/O in user function.
Global input used for high fanout, or clock/ reset net. The
G0 pin drives the GBUF0 global buffer.
In user mode, after configuration, this pin can be
programmed as general I/O in user function.
Global input used for high fanout, or clock/ reset net. The
G1 pin drives the GBUF1 global buffer.
In user mode, after configuration, this pin can be
programmed as general I/O in user function.
Global input used for high fanout, or clock/ reset net. The
G3 pin drives the GBUF3 global buffer.
In user mode, after configuration, this pin can be
programmed as general I/O in user function.
Global input used for high fanout, or clock/ reset net. The
G4 pin drives the GBUF4 global buffer.
In user mode, after configuration, this pin can be
programmed as general I/O in user function.
Global input used for high fanout, or clock/ reset net. The
G5 pin drives the GBUF5 global buffer.
In user mode, after configuration, this pin can be
programmed as general I/O in user function.
Global input used for high fanout, or clock/ reset net. The
G6 pin drives the GBUF6 global buffer.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
43
iCE40 UltraPlus Family Data Sheet
Data Sheet
5.1.5. General I/O, LED Pins
Signal Name
General I/O
RGB0
RGB1
Shared Function
—
—
Function
I/O
Description
General I/O
OpenDrain I/O
LED
OpenDrain
Output
OpenDrain I/O
In user mode, when RGB function is not used, this pin can
be connected to any user logic and used as open-drain I/O.
This pin is located in Bank 0.
In user mode, when using RGB function, this pin can be
programmed as open drain 24 mA output to drive external
LED.
In user mode, when RGB function is not used, this pin can
be connected to any user logic and used as open-drain I/O.
This pin is located in Bank 0.
In user mode, when using RGB function, this pin can be
programmed as open drain 24 mA output to drive external
LED.
In user mode, when RGB function is not used, this pin can
be connected to any user logic and used as open-drain I/O.
This pin is located in Bank 0.
In user mode, when using RGB function, this pin can be
programmed as open drain 24 mA output to drive external
LED.
In user mode, with user's choice, this pin can be
programmed as I/O in user function in the top (xx = I/O
location). These pins are located in Bank 0.
In user mode, with user's choice, this pin can be
programmed as I/O in user function in the bottom (xx = I/O
location). Pins with xx are located in Bank 1.
General I/O
LED
RGB2
—
General I/O
LED
OpenDrain
Output
OpenDrain I/O
PIOT_xx
—
General I/O
OpenDrain
Output
I/O
PIOB_xx
—
General I/O
I/O
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
44
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
5.2. Pin Information Summary
iCE40UP3K
UWG30
UWG30
General Purpose I/O Per
Bank 0
7
7
Bank
Bank 1
10
10
Bank 2
4
4
Total General Purpose I/Os
21
21
VCC
1
1
VCCIO
Bank 0
1
1
Bank 1
1
1
Bank 2
1
1
VCCPLL
1
1
VPP_2V5
1
1
Dedicated Config Pins
1
1
GND
2
2
Total Balls
30
30
*Note: 48-pin QFN package (SG48) requires the package paddle to be connected to GND.
Pin Type
iCE40UP5K
SG48
17
14
8
39
2
1
1
1
1
1
2
0*
48
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
45
iCE40 UltraPlus Family Data Sheet
Data Sheet
5.3. iCE40UP Part Number Description
i C E40 UP XX - XX XX XI T R
Device Family
iCE40UP FPGA
TR
= Default Tape and Reel
for SG48 (See quantity below)
TR = Tape and Reel (See quantity below)
TR50 = Tape and Reel, 50 units
TR1K = Tape and Reel, 1,000 units
Logic Cells
3K = 2,800 Logic Cells
5K = 5,280 Logic Cells
Grade
I = Industrial
Package
UWG30 = 30-Ball WLCSP (0.40 mm Ball Pitch)
SG48 = 48-Pin QFN (0.50 mm Pin Pitch)
All parts are shipped in tape-and-reel.
5.3.1. Tape and Reel Quantity
Package
UWG30
SG48
TR Quantity
5,000
2,000
5.4. Ordering Part Numbers
5.4.1. Industrial
Part Number
iCE40UP3K-UWG30ITR
iCE40UP3K-UWG30ITR1K
iCE40UP3K-UWG30ITR50
iCE40UP5K-SG48I
iCE40UP5K-SG48ITR50
iCE40UP5K-UWG30ITR
iCE40UP5K-UWG30ITR1K
iCE40UP5K-UWG30ITR50
LUTs
2800
2800
2800
5280
5280
5280
5280
5280
Supply Voltage
1.2 V
1.2 V
1.2 V
1.2 V
1.2 V
1.2 V
1.2 V
1.2 V
Package
Halogen-Free WLCSP
Halogen-Free WLCSP
Halogen-Free WLCSP
Halogen-Free QFN
Halogen-Free QFN
Halogen-Free WLCSP
Halogen-Free WLCSP
Halogen-Free WLCSP
Pins
30
30
30
48
48
30
30
30
Temperature
IND
IND
IND
IND
IND
IND
IND
IND
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
46
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Supplemental Information
For Further Information
A variety of technical documents for the iCE40 UltraPlus family are available on the Lattice web site.
iCE40 Programming and Configuration (FPGA-TN-02001)
iCE40 SPI/I2C Hardened IP Usage Guide (FPGA-TN-02010)
Advanced iCE40 SPI/I2C Hardened IP Usage Guide (FPGA-TN-02011)
Memory Usage Guide for iCE40 Devices (FPGA-TN-02002)
iCE40 sysCLOCK PLL Design and Usage Guide (FPGA-TN-02052)
iCE40 Hardware Checklist (FPGA-TN-02006)
iCE40 LED Driver Usage Guide (FPGA-TN-02021)
DSP Function Usage Guide for iCE40 Devices (FPGA-TN-02007)
iCE40 Oscillator Usage Guide (FPGA-TN-02008)
iCE40 SPRAM Usage Guide (FPGA-TN-02022)
iCE40 UltraPlus Pinout Files
iCE40 UltraPlus Pin Migration Files
Thermal Management
Package Diagrams
Lattice design tools
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
47
iCE40 UltraPlus Family Data Sheet
Data Sheet
Technical Support
For assistance, submit a technical support case at www.latticesemi.com/techsupport.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
48
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Revision History
Revision 1.9, December 2020
Section
DC and Switching Characteristics
—
Change Summary
Updated values in Table 4.17. sysDSP Timing.
Updated footnotes in Table 4.23. SPI Master or NVCM Configuration Time.
Minor style adjustments
Revision 1.8, August 2020
Section
Architecture
Supplemental Information
Change Summary
Removed paragraph regarding SCLK and SDI inputs from sysCLOCK Phase Locked Loops
(PLLs) section.
Updated linked reference.
Modified Figure 3.3. PLL Diagram.
Updated document ID of sysCLOCK PLL Design and Usage Guide in For Further Information
section.
Revision 1.7, February 2020
Section
Disclaimers
Change Summary
Added this section.
Revision 1.6, November 2018
Section
General Description
Product Family
Change Summary
Corrected product dimensions from 2.15 mm × 2.55 mm to 2.11 mm × 2.54 mm.
Revision 1.5, August 2018
Section
All
DC and Switching Characteristics
Pinout Information
Supplemental Information
Change Summary
Removed Copyright page.
Updated sysCONFIG Port Timing Specifications section. Updated tCR_SCK parameter in Table
4.24.
Updated Configuration SPI Pins section.
Updated secondary signal name from SPI_SS_B to SPI_SS.
Updated iCE40 Programming and Configuration document number.
Revision 1.4, August 2017
Section
All
Change Summary
Changed document number from DS1056 to FPGA-DS-02008.
Removed Preliminary from document cover page and header.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
49
iCE40 UltraPlus Family Data Sheet
Data Sheet
Revision 1.3, August 2017
Section
All
Change Summary
Changed document status from Advance to Preliminary.
Updated footer.
Architecture
Corrected link to iCE40 LED Driver Usage Guide (TN1288).
Added link to iCE40 SPRAM Usage Guide (TN1314).
DC and Switching Characteristics
Updated Typ VCC=1.2 V values for IPP_2VSPEAK and ICOOPEAK in Table 4.6. Supply Current.
Added Min value for fMAXSRAM to Table 4.18. Single Port RAM Timing.
Added LVCMOS12 information to Table 4.19. Maximum sysI/O Buffer Performance and
Table 4.20. iCE40 UltraPlus Family Timing Adders.
Updated Table 4.21. iCE40 UltraPlus External Switching Characteristics. Revised Max
values for tISKEW_GBUF, tSKEW_IO, tCO, tCOPLL, and Min values for tSUPLL, tHPLL.
Added Max values to Table 4.23. SPI Master or NVCM Configuration Time.
Pinout Information
Updated TR description in the iCE40UP Part Number Description section.
Updated part number information in the Ordering Part Numbers section.
Supplemental Information
Corrected link to iCE40 LED Driver Usage Guide (TN1288).
Added link to iCE40 SPRAM Usage Guide (TN1314).
Added link to Package Diagrams.
Revision 1.2, June 2016
Section
All
Introduction
Product Family
Change Summary
Updated template.
Added QFN package in features list.
Added packages to Table 2.1. iCE40 UltraPlus Family Selection Guide.
Added information on RGB PWM IP in Overview.
Architecture
Performed minor editorial changes.
Added information on 256 kb SPRAM blocks.
Changed headings in Table 3.2. Global Buffer (GBUF) Connections to Programmable
Logic Blocks.
Corrected VCCPLL format in Figure 3.3. PLL Diagram.
Updated note in Table 3.4. sysMEM Block Configurations.
Added reference to iCE40 SPRAM Usage Guide (TN1314).
Revised sysI/O Buffer Banks information.
Corrected VCCIO format in Figure 3.9. I/O Bank and Programmable I/O Cell.
Revised Typical I/O Behavior During Power-up information.
Revised Supported Standards information.
Revised heading in Table 3.9. Supported Input Standards.
Revised heading and removed LVCMOS12 in Table 3.10Table 3.10. Supported Output
Standards.
Revised HFOSC information in On-Chip Oscillator section.
Removed "An RGB PWM IP is also offered in the family." in RGB High Current Drive I/O
Pins section.
DC and Switching Characteristics
Added the following figures:
Figure 4.1. Power Up Sequence with SPE_VCCIO1 and VPP_2V5 Not Connected
Together.
Figure 4.2. Power Up Sequence with All Supplies Connected Together to 1.8 V.
Updated note in Table 4.5. DC Electrical Characteristics.
Added note in Table 4.6. Supply Current.
Revised User SPI Specifications 1, 2 section.
Removed symbols.
Added notes.
Revised Table 4.11. Internal Oscillators (HFOSC, LFOSC).
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
50
FPGA-DS-02008-1.9
iCE40 UltraPlus Family Data Sheet
Data Sheet
Section
Change Summary
Removed note in Table 4.13. sysI/O Single-Ended DC Electrical Characteristics.
Changed to Lattice Design Software tool in Table 4.15. Pin-to-Pin Performance
(LVCMOS25).
Changed to Lattice Design Software tool and revised note in Table 4.16. Register-toRegister Performance.
Added sysDSP Timing section.
Added SPRAM Timing section.
Removed LVCMOS12 and added timing values in Table 4.19. Maximum I/O Buffer
Performance.
Removed LVCMOS12 and added timing values in Table 4.20. iCE40 UltraPlus Family
Timing Adders.
Revised max values in Table 4.23. SPI Master or NVCM Configuration Time.
Removed TBD conditions in Table 4.24. sysCONFIG Port Timing Specifications. Revised
tHD parameter.
Revised Table 4.25. High Current RGB LED and IR LED Drive.
Pinout Information
General update to Signal Descriptions section.
Updated the iCE40UP Part Number Description section. Added FGW49 package.
Added OPNs.
Added reference to FPGA-TN-02022, iCE40 SPRAM Usage Guide .
Supplemental Information
Revision 1.1, September 2015
Section
Architecture
Pinout Information
Ordering Information
Further Information
Change Summary
Updated Architecture section. Replaced iCE5UP with iCE40UP.
Updated Pin Information section.
Replaced iCE5UP with iCE40UP.
Replaced SWG30 with UWG30.
Updated iCE40UP Part Number Description section.
Replaced iCE5UP with iCE40UP.
Replaced SWG30 with UWG30.
Updated Ordering Part Numbers section. Replaced the table of part
Removed reference to Schematic Symbols.
Revision 1.0, August 2015
Section
All
Change Summary
Initial release.
© 2018-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal.
All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
FPGA-DS-02008-1.9
51
www.latticesemi.com