APR-B10_1

AC Current transducer APR-B10 Split core transducer for the electronic measurement distorted AC waveforms current, with galvanic isolation between the primary (High power) and the secondary circuits (Electronic circuit). Switch selectable ranges and True RMS 0-5V and 0-10V switch selectable voltage output. IPN = 10 .. 400 A Electrical data Primary Nominal Current I PN ( A.t.RMS) 10,25,50 50,75,100 100,150,200 200,300,400 Analogue Output Signal V OUT ( V) 0-5V 0-5V 0-5V 0-5V or or or or 0-10V 0-10V 0-10V 0-10V Type APR APR APR APR 50 B10 100 B10 200 B10 400 B10 Features • VFD and SCR waveforms current measurement • True RMS output • Split core type • 5V & 10V switch selectable voltage output • DIN mounting & Panel mounting • Eliminates insertion loss • Switch selectable ranges RL VC IC Load resistance Supply voltage Current Consumption Limitation of voltage output (0-10V) Limitation of voltage output (0-5V) Overloaded input current ≥ 10 kΩ +24 ±5% V DC < 30 mA 14 V 7 V no limitation Accuracy-Dynamic performance data X ε L VOE VOT TCε G tr f Accuracy @ IPN, TA = 25°C (without offset) Linearity (0 .. ± IPN) Electrical offset voltage, TA = 25°C Thermal drift of VOE Thermal drift of the gain (% of reading) Response time @ 90% of IP Frequency bandwidth (±1%) < ±1 % of IPN < ±0.5 % of IPN < ±0.5 % of IPN ±1 mV/K ±0.1 %/K < 400 ms 30 .. 6000 Hz Advantages • Large aperture for cable up to Ø18mm • High isolation between primary and secondary circuits • Easy to mount General data TA TS m dCp dCl CTI Ambient operating temperature Ambient storage temperature Mass Protection type Creepage distance Clearance distance Comparative tracking index (Group I) UL94 classification -20 .. +60 °C -20 .. +85 °C 90 g IP20 5.5 mm 5.5 mm 600 V V0 Applications • VFD Controlled Loads: VFD output indicates how the motor and attached load are operating. • SCR Controlled Loads: Acurate measurement of phase angle fired or burst fired (time proportioned) SCRs. Current measurement gives faster response than temperature measurement. • Switching Power Supplies and Insulation category Vb Rated Voltage 300 with IEC 61010-1 standards and following conditions : - Single insulation - Over voltage category CAT III - Pollution degree PD2 - None uniform field R.m.s. voltage for AC insulation test, 50Hz, 1mn 5 R.m.s. voltage for partial discharge extinction @ 10pC 1.5 Peak impulse withstand voltage 1.2/50µs 6.1 If insulated cable is used for the primary circuit, the voltage category could be improved with the following table : Cable insulation (primary) Category HAR 05 600V CAT III HAR 07 1000V CAT III The operator must have accrediation to install this material. The users must take care of all protection gurantee against electrical shock. V Vd Ve Vw kV kV kV Electronic Ballasts: True RMS sensing is the most accurate way to measure power supply or ballast input power. 041029/3 Notes : Installation and maintenance should be done with power supply disconnected. LEM Components www.lem.com Dimensions AP(R)-B10 Output Vo ltage Selection Switch 20 Front Vie w 55 (unit : mm, 1mm = 0.0394 inch) Left View 16.40 Rang e Selection Switch 14.80 4.7 0 40(distance between screws) 37 33.50 Axis of ape rture 67 21 25 18 .50 Plug-in connector included : XW4B-03C1-H1 (OMRON) 18.50 Bottom View Mechanical characteristics • General tolerance • Primary aperture • Panel mounting • Distance between holes ±1 mm ∅ 18.5 mm 2 holes ∅ 4.0 mm 40.0 mm For panel mounting, replace M4 screws by new one (not supplied) with appropriate length to panel´s thickness. Connections • Wires up to 2 mm ∅ 0-5, 10V Selectable GND RL OUTPUT AP/APR +24VDC Output Connector 3(-) 2(out)1(+) Output Switch Range Switch Front Ip Is DIN size35.50 69 +24VDC OUT GND LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice.