HAIS400-P

Current Transducer HAIS 50..400-P and HAIS 50..100-TP For the electronic measurement of currents : DC, AC, pulsed, mixed, with a galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). IPN = 50 .. 400 A All Data are given with a R L = 1 0 k Ω Electrical data Primary nominal current rms IPN (A) 50 100 150 200 400 Primary current, measuring range IPM (A) ± ± ± ± ± 150 300 450 600 600 Type RoHS since date code 45231, 46272 45231, 46012 46172 45231 planned Features • Hall effect measuring principle • Galvanic isolation between primary • Isolation test voltage 2500V • Low power consumption • Single power supply +5V • Fixed offset & gain • Bus bar version available for 50A and • Insulated plastic case recognized according to UL94-V0. 100A ratings. and secondary circuit HAIS 50-P, HAIS 50-TP1) HAIS 100-P, HAIS 100-TP1) HAIS 150-P HAIS 200-P HAIS 400-P VOUT VREF RL ROUT CL VC IC Output voltage (Analog) @ IP IP = 0 Reference voltage 2) - Output voltage VREF Output impedance VREF Load impedance Load resistance Output internal resistance Capacitive loading Supply voltage (± 5 %) Current consumption @ VC = 5 V VREF ± (0.625·IP/IPN) V VREF ± 0.025 V 2.5 ± 0.025 V typ. 200 Ω ≥ 200 kΩ ≥2 kΩ < 10 Ω 1.4 8 >8 >8 > 600 kV kV kV kV mm mm Vw dCp dCl CTI If insulated cable is used for the primary circuit, the voltage category could be improved with the following table : Cable insulation (primary) Category HAR 03 450V CAT III HAR 05 550V CAT III HAR 07 650V CAT III Safety This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the following manufacturer's operating instructions. Caution, risk of electrical shock When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a built-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. Page 2/3 0 61018/6 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com Dimensions HAIS 50..400-P and HAIS 50..100-TP (in mm. 1 mm = 0.0394 inch) HAIS 50..400-P Front view 33 15 HAIS 50..100-TP Front view 33 Right view 8 29 16 29 0.5 3.5 3 0.5 3 1.5 2-D1.0 4-0.25x0.45 6 2-D1.0 Bottom view 3-P1.8 3-P1.8 Bottom view 10 1.5 19.9 5 1 1 3.5 4.3 4 14.5 11 11 6.5 4.3 1.5 5 1.5 6.5 11 4 14.5 11 Terminal Pin Identification 1...+5V 2...0V 3...OUTPUT 4...Vref. (IN/OUT) 5...Core Earth (*) 6...NC. Recommended connection circuit Required Connection Circuit 1 2 3 4 47nF 4.7nF 47nF +5V 0V OUTPUT Vref. (IN/OUT) 5 Recommended PCB hole Pin 1-4 : 0.7 ±0.1mm Pin 5-6 : 1.5 ±0.1mm Primary bus bar : 2.3 ±0.1mm Operation Principle +Vc Vout Vref.(IN/OUT) Ip 0V General tolerance : ±0.2mm Unit : mm (*) s hould be connected to 0V of Power Supply for better dv/dt immunity. Arrow indicates positive current direction. 6 25.9 14 6 6 Page 3/3 061018/6 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com