HAT1500-S

Current Transducer HAT 200..1500-S For the electronic measurement of currents: DC, AC, pulsed, mixed, with a galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). IPN = 200..1500 A VOUT = ± 4 V Electrical data Primary nominal r.m.s. current IPN (A) 200 400 500 600 750 800 1000 1200 1500 Primary current measuring range 4) IP (A) ± ± ± ± ± ± ± ± ± 600 1200 1500 1800 2250 2400 3000 3000 3000 Type HAT HAT HAT HAT HAT HAT HAT HAT HAT 200-S 400-S 500-S 600-S 750-S 800-S 1000-S 1200-S 1500-S Features • Hall effect measuring principle • Galvanic isolation between primary • • • • and secondary circuit Isolation voltage 3000 V Low power consumption Extended measuring range(3 x IPN) Insulated plastic case recognized according to UL 94-V0 VC IC R IS VOUT ROUT RL Supply voltage (± 5 %) 4) Current consumption Isolation resistance @ 500 VDC Output voltage @ ± IPN, RL = 10 kΩ, TA = 25°C Output internal resistance Load resistance ± 15 ± 15 > 1000 ±4 100 > 10 V mA MΩ V Ω kΩ Advantages • Easy mounting • Small size and space saving • Only one design for wide current ratings range Accuracy-Dynamic performance data ε X L VOE VOH VOT TCε G tr f Accuracy @ IPN, TA = 25°C (without offset) Linearity error 1) (0 .. ± IPN) Electrical offset voltage, TA = 25°C Hysteresis offset voltage @ IP = 0; after an excursion of 1 x IPN Thermal drift of VOE Thermal drift of the gain (% of reading) Response time @ 90% of IP Frequency bandwidth 2) (- 3 dB) < ± 1 % of IPN < ± 1 % of IPN < ± 20 mV < ± 10 mV 11 275 kV mm mm 051011/9 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice. Page 2/3 LEM Industrial www.lem.com Dimensions HAT 200..1500-S (in mm. 1 mm = 0.0394 inch) Top view H AT-S SERIES 12 = = 12 = = (unit = mm) H AT 500-S to 1 500-S Positive curren flow current t 70 10 12 5 30.5 30.5 x 40.5 1 15.5 4 Molex 5045-04A 6 78 4 10 30 65 46 Max. 24 29 38 1 Front view H AT 200-S 4 90 1 (+) All holes O 4.5mm Pins arrangement 2 3 (-) Output 4 0V Fixation by base-plate or on bus bar Mechanical characteristics • General tolerance • Transducer fastening 30.5 x 40.5 Safety with M screws 4 • Connection of secondary ± 1 mm By base-plate 1or on 432 bus bar Molex 5045-04A with M4 screws. All slots ∅ 4.5 mm Molex 5045-04A Pins arrangement: 1 (+) 2 (-) 3 Output 4 0V This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements 99/05 in accordance with the following manufacturer's operating instructions. Caution, risk of electrical shock Remarks • IS is positive when IP flows in the direction of the arrow. • Temperature of the primary conductor should not exceed 100°C. When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a built-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. 0 51011/9 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice. Page 3/3 LEM Industrial www.lem.com