LFD4K5-6SBKS-XX-S3-PF

LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only FOUR DIGIT LED DISPLAY (0.39 Inch) Pb Lead-Free Parts LFD4K5/6SBKS-XX/S3-PF DATA SHEET DOC. NO REV. DATE : : QW0905- LFD4K5/6SBKS-XX/S3-PF B : 31 - Jul. - 2006 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LFD4K5/6SBKS-XX/S3-PF Page 1/8 Package Dimensions LFD4K5/6SBKS-XX/S3-PF BIN GRADING ORDER DATE 40.18(1.582") CUSTOMER P/N LAPLING 7.0(0.276") DIG.1 10.0 (0.39") DIG.2 L1 L2 DIG.3 L3 DIG.4 12.8 (0.504") 10.5±0.5 1.2 90° ±5° 17.5MIN Ø 0.51TYP 2.54*13=33.02 A FG E D B C DP PIN NO.1 Note : 1.All dimension are in millimeters and (lnch) tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LFD4K5/6SBKS-XX/S3-PF Page 2/8 Internal Circuit Diagram LFD4K5SBKS-XX/S3-PF LFD4K6SBKS-XX/S3-PF 14 13 12 11 10 9 8 14 13 12 11 10 9 8 A DIG.1 B C D 5 E F G A DIG.2 B C D 4 E F G A DIG.3 B C D 2 E F G A DIG.4 B C D 1 E F G L1 L2 A DIG.1 B C D 5 E F G A DIG.2 B C D 4 E F G A DIG.3 B C D 2 E F G A DIG.4 B C D 1 E F G L1 L2 3 3 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LFD4K5/6SBKS-XX/S3-PF Page 3/8 Electrical Connection PIN NO.1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LFD4K5SBKS-XX/S3-PF Common Cathode Dig.4 Common Cathode Dig.3 Cathode L1,L2 PIN NO.1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LFD4K6SBKS-XX/S3-PF Common Anode Dig.4 Common Anode Dig.3 Anode L1,L2 Common Anode Dig.2 Common Anode Dig.1 NO CONNECT NO CONNECT Cathode G Cathode F Cathode E Cathode D Cathode C Cathode B,L2 Cathode A,L1 Common Cathode Dig.2 Common Cathode Dig.1 NO CONNECT NO CONNECT Anode G Anode F Anode E Anode D Anode C Anode B,L2 Anode A,L1 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LFD4K5/6SBKS-XX/S3-PF Page 4/8 Absolute Maximum Ratings at Ta=25 ℃ Ratings Parameter Symbol SBKS Forward Current Per Chip Peak Forward Current Per Chip (Duty 1/10,0.1ms Pulse Width) Power Dissipation Per Chip Reverse Current Per Any Chip Electrostatic Discharge( * ) Operating Temperature Storage Temperature IF 30 mA mA UNIT IFP 100 PD Ir ESD Topr Tstg 120 50 500 -25 ~ +85 -25 ~ +85 mW μA V ℃ ℃ Solder Temperature 1/16 Inch Below Seating Plane For 3 Seconds At 260 ℃ Static Electricity or power surge will the Use of anti-electrosatic * glove is recommended when handingdamageLED.LED.devices, a conductive wrist band or must be properly these All equipment and machinery grounded. Part Selection And Application Information(Ratings at 25℃) Electrical CHIP PART NO Material LFD4K5SBKS-XX/S3-PF common cathode Emitted or anode Common Cathode λD (nm) △λ (nm) Vf(v) Iv(mcd) IV-M Typ. Max. Min. Typ. InGaN/SiC Blue 475 Common Anode 26 3.5 4.2 5.0 8.5 2:1 LFD4K6SBKS-XX/S3-PF Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ± 15% testing tolerance. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LFD4K5/6SBKS-XX/S3-PF Page 5/8 Test Condition For Each Parameter Parameter Forward Voltage Per Chip Luminous Intensity Per Chip Dominant Wavelength Spectral Line Half-Width Reverse Current Any Chip Luminous Intensity Matching Ratio Symbol Vf Iv Unit volt mcd nm nm Test Condition If=20mA If=10mA If=20mA If=20mA Vr=5V λD △λ Ir IV-M μA LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LFD4K5/6SBKS-XX/S3-PF Page 6/8 Typical Electro-Optical Characteristics Curve SBK-S CHIP Fig.1 Forward current vs. Forward Voltage 30 25 20 15 10 5 0 1 2 3 4 5 Fig.2 Relative Intensity vs. Forward Current Forward Current(mA) 1.5 Relative Intensity Normalize @20mA 1.25 1.0 0.75 0.5 0.25 0 0 5 10 15 20 25 30 Forward Voltage(V) Forward Current(mA) Fig.3 Forward Current vs. Temperature Fig.4 Relative Intensity vs. Wavelength Forward Current@20mA 30 20 10 0 0 25 50 75 100 Relative Intensity@20mA 40 1.0 0.5 0 380 430 480 530 580 630 680 Ambient Temperature( ℃) Wavelength (nm) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LFD4K5/6SBKS-XX/S3-PF Page 7/8 Soldering Condition(Pb-Free) 1.Iron: Soldering Iron:30W Max Temperature 350° C Max Soldering Time:3 Seconds Max(One Time) Distance:Solder Temperature 1/16 Inch Below Seating Plane For 3 Seconds At 260° C 2.Wave Soldering Profile Dip Soldering Preheat: 120° C Max Preheat time: 60seconds Max Ramp-up 2° C/sec(max) Ramp-Down:-5° C/sec(max) Solder Bath:260° C Max Dipping Time:3 seconds Max Distance:Solder Temperature 1/16 Inch Below Seating Plane For 3 Seconds At 260° C Temp( ° C) 260° C3sec Max 260 ° 5° /sec max 120 ° 2° /sec max Preheat 60 Seconds Max 25° 0° 0 50 100 150 Time(sec) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LFD4K5/6SBKS-XX/S3-PF Page 8/8 Reliability Test: Test Item Test Condition 1.Under Room Temperature 2.If=10mA 3.t=1000 hrs (-24hrs, +72hrs) Description This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. Reference Standard MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 Operating Life Test High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. J IS C 7021: B-12 High Temperature High Humidity Test 1.Ta=65 ℃±5 ℃ 2.RH=90 %~95% 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hours. MIL-STD-202:103B JIS C 7021: B-11 Thermal Shock Test 1.Ta=105 ℃±5℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5 ℃ 2.Dwell time= 10 ±1sec. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5 ℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2