LH9033-TR3

LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT TAPE AND REEL Pb Lead-Free Parts LH9033/TR3 DATA SHEET DOC. NO REV. DATE : : : QW0905-LH9033/TR3 A 18 - Jul. - 2005 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. : LH9033/TR3 Page 1/7 Package Dimensions Cathode 0.4± 0.1 2.5 0.5± 0.1 2.0 ψ1.9 1.4 0.76MAX 2.8 0.31TYP 0.61TYP 1.07TYP 7.62MAX 0.13TYP Note : 1.All dimension are in millimeter tolerance is ± 0.2mm unless otherwise noted. 2.Specifications are subject to change without notice. Carrier Type Dimensions 4.0 2.52 0.35 9.3 12.0±0.3 7.84 5.5 Polarity 1.75 2.0 4.0 ψ1.5 3.37 Note : The tolerances unless mentioned is ±0.2mm,Angle ± 0.5. Unit=mm. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. : LH9033/TR3 Page 2/7 Reel Dimensions 16.0±1.0 ψ178±2.0 14.2±1.0 74.0±1.5 Part No. LH9033/TR3 Description 12.0mm tape,7"reel Quantity/Reel 1500 devices LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. : LH9033/TR3 Page 3/7 Absolute Maximum Ratings at Ta=25 ℃ Ratings Parameter Symbol H Forward Current Peak Forward Current Duty 1/10@10KHz Power Dissipation Reverse Current @5V Operating Temperature Storage Temperature Soldering Temperature IF IFP PD Ir Topr Tstg Tsol 15 60 40 10 -40 ~ +85 -40 ~ +100 Max 260 ℃ for 5 sec Max (2mm from body) mA mA mW UNIT μA ℃ ℃ Typical Electrical & Optical Characteristics (Ta=25 ℃) PART NO MATERIAL COLOR Peak wave length λPnm Luminous Viewing Spectral Forward voltage intensity angle halfwidth @20 mA(V) @10mA(mcd) 2θ 1/2 △λ nm (deg) Emitted LH9033/TR3 Lens Water Clear 697 90 Min. Max. Min. 1.7 2.6 4.5 Typ. 7.0 20 GaP Red Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. : LH9033/TR3 Page 4/7 Typical Electro-Optical Characteristics Curve H CHIP Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current 3.0 1000 Forward Current(mA) 100 Relative Intensity Normalize @20mA 1.0 2.0 3.0 4.0 5.0 2.5 2.0 1.5 1.0 0.5 0.0 1.0 10 100 1000 10 1.0 0.1 Forward Voltage(V) Fig.3 Forward Voltage vs. Temperature Forward Current(mA) Fig.4 Relative Intensity vs. Temperature Forward Voltage@20mA Normalize @25 ℃ Relative Intensity@20mA Normalize @25 ℃ 0 20 40 60 80 100 1.2 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 100 1.1 1.0 0.9 0.8 -40 -20 Ambient Temperature( ℃) Ambient Temperature( ℃) Fig.5 Relative Intensity vs. Wavelength Fig.6 Directive Radiation Relative Intensity@20mA 1.0 0° -30° 30° 0.5 -60° 60 ° 0.0 600 700 800 900 1000 100% 75% 50% 25% 0 25% 50% 75% 100% Wavelength (nm) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. : LH9033/TR3 Recommended Soldering Conditions 1. Hand Solder Basic spec is ≦ 280℃ 3 sec one time only. Page 5/7 2. Wave Solder Soldering heat Max. 260 ℃ 245±5℃ within 5 sec Preheat 120 ~ 150℃ 120 ~ 180 sec 3-1. LEAD Reflow Solder Temp. (℃ ) 240 Rising +5 ℃/sec Cooling -5 ℃/sec 150 120 Preheat 60 ~ 120 sec 5sec Time 3-2 PB-Free Reflow Solder 1~5° C/sec 260° C MaX. 10sec.Max Preheat 180~200° C 1~5° C/sec Above 220° C 60 sec.Max. 120 sec.Max. Reflow Soldering should not be done more than two times. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. : LH9033/TR3 Precautions For Use: Storage time: 1.The operation of Temperatures and RH are : 5 ℃~35℃,RH60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 ℃ ~ 35℃,RH60%, they should be treated at 60 ℃± 5 ℃fo r 15hrs. Page 6/7 Drive Method: LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED. Cleaning: Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED. ESD(Electrostatic Discharge): Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. : LH9033/TR3 Reliability Test: Page 7/7 Classification Test Item Test Condition 1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) Reference Standard MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1 Operating Life Test High Temperature Storage Test Endurance Test Low Temperature Storage Test 1.Ta=105 ℃±5 ℃ 2.t=1000 hrs (-24hrs, +72hrs) MIL-STD-883D:1008 JIS C 7021: B-10 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) JIS C 7021: B-12 High Temperature High Humidity Storage Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95 % 3.t=1000hrs ±2hrs MIL-STD-202F:103B JIS C 7021: B-11 Thermal Shock Test 1.Ta=105 ℃±5 ℃&-40 ℃±5℃ (10min) (10min) 2.total 10 cycles MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011 MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4 Solderability Test 1.T.Sol=235 ℃±5℃ 2.Immersion time 2 ±0.5sec 3.Coverage ≧95% of the dipped surface Environmental Test Temperature Cycling 1.105 ℃ ~ 25 ℃ ~ -55 ℃ ~ 25 ℃ 30mins 5mins 30mins 5mins 2.10 Cyeles IR Reflow 1.T=260° C Max. 10sec.Max. 2. 6 Min MIL-STD-750D:2031.2 J-STD-020