LSD335-66-XX-RP38-PF

LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SINGLE DIGIT LED DISPLAY (0.32 Inch) Pb Lead-Free Parts LSD335/66-XX/RP38-PF DATA SHEET DOC. NO REV. DATE : : QW0905- LSD335/66-XX/RP38-PF A : 31 - May - 2005 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSD335/66-XX/RP38-PF Page 1/8 Package Dimensions PIN NO.1 LSD335/66-XX/RP38-PF LIGITEK 7.5 (0.30") 6.50 (0.256") 8.0 (0.315") 13.0 (0.51") 10.16 (0.40") 0.5(0.02") ψ1.0 ψ0.45 TYP 3.8±0.5 5.08 (0.20") Note : 1.All dimension are in millimeters and (lnch) tolerance is ±0.25(0.01") unless otherwise noted. 2.Specifications are subject to change without notice. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSD335/66-XX/RP38-PF Page 2/8 Internal Circuit Diagram LSD3356-XX/RP38-PF 1,6 A BCDE F G DP 10 9 8 5 4 2 3 7 LSD3366-XX/RP38-PF 1,6 A BCDE F G DP 10 9 8 5 4 2 3 7 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSD335/66-XX/RP38-PF Page 3/8 Electrical Connection PIN NO. 1 2 3 4 5 6 7 8 9 10 LSD3356-XX/RP38-PF Common Cathode Anode F Anode G Anode E Anode D Common Cathode Anode DP Anode C Anode B Anode A PIN NO. 1 2 3 4 5 6 7 8 9 10 LSD3366-XX/RP38-PF Common Anode Cathode F Cathode G Cathode E Cathode D Common Anode Cathode DP Cathode C Cathode B Cathode A LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSD335/66-XX/RP38-PF Page 4/8 Absolute Maximum Ratings at Ta=25 ℃ Ratings Parameter Symbol HR Forward Current Per Chip Peak Forward Current Per Chip (Duty 1/10,0.1ms Pulse Width) Power Dissipation Per Chip Reverse Current Per Any Chip Operating Temperature Storage Temperature IF IFP 30 100 mA mA UNIT PD Ir Topr Tstg 100 10 -25 ~ +85 -25 ~ +85 mW μA ℃ ℃ Solder Temperature 1-16 Inch Below Seating Plane For 3 Seconds At 260 ℃ Part Selection And Application Information(Ratings at 25℃) Electrical PART NO common λP △λ Vf(v) Iv(mcd) IV-M cathode (nm) (nm) Material Emitted or anode Min. Typ. Max. Min. Typ. CHIP Common Cathode GaAlAs Red Common Anode 660 20 1.5 1.7 2.4 3.05 6.1 2:1 LSD3356-XX/RP38-PF LSD3366-XX/RP38-PF Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSD335/66-XX/RP38-PF Page 5/8 Test Condition For Each Parameter Parameter Forward Voltage Per Chip Luminous Intensity Per Chip Peak Wavelength Spectral Line Half-Width Reverse Current Any Chip Luminous Intensity Matching Ratio Symbol Vf Iv Unit volt mcd nm nm Test Condition If=20mA If=10mA If=20mA If=20mA Vr=5V λP △λ Ir IV-M μA LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSD335/66-XX/RP38-PF Page 6/8 Typical Electro-Optical Characteristics Curve HR CHIP Fig.1 Forward current vs. Forward Voltage 1000 Fig.2 Relative Intensity vs. Forward Current 3.0 Relative Intensity@20mA 1.0 2.0 3.0 4.0 5.0 Forward Current(mA) 2.5 2.0 1.5 1.0 0.5 0 1.0 10 100 1000 100 10 1.0 0.1 Forward Voltage(V) Fig.3 Forward Voltage vs. Temperature Forward Current(mA) Fig.4 Relative Intensity vs. Temperature Forward Voltage@20mA Relative Intensity@20mA 40 60 1.2 1.1 3.0 2.5 2.0 1.5 1.0 0.5 0 -40 1.0 0.9 0.8 -40 -20 -0 20 80 100 -20 -0 20 40 60 80 100 Ambient Temperature( ℃) Ambient Temperature( ℃) Fig.5 Relative Intensity vs. Wavelength Relative Intensity@20mA 1.0 0.5 0 600 650 700 750 Wavelength (nm) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSD335/66-XX/RP38-PF Page 7/8 Wave soldering Profile Temp(°C) 245°C 5sec Max 245° 5°/sec max 3°/sec max Soldering Soldering Iron:30W Max Temperature 300 ° C Max Soldering Time:3 Seconds Max Distance:2mm Min(From solder joint to case) 120° 25° 120 Seconds Max Preheat Dip Soldering Preheat: 120 °C Max Time(sec) Preheat time: 120 seconds Max Ramp-up 3°C/sec(max) Ramp-Down:-5 ° C/sec(max) Solder Bath:245 °C Max Dipping Time:5 seconds Max Distance:2mm Min(From solder joint to case) Wave Soldering Profile (Pb Free) Temp(°C) 265°C 5sec Max 265° Soldering Soldering Iron:30W Max Temperature:350 ° CMax Soldering Time:3seconds Max Distance:2mm Min(From solder joint to case) 140° 3°/sec max 5°/sec max 25° 120 Seconds Max Preheat Dip Soldering Preheat: 140°C Max Preheat time: 120seconds Max Time(sec) Ramp-up 3°C/sec(max) Ramp-Down:-5 ° C/sec(max) Solder Bath:265 ° C Max Dipping Time:5 seconds Max Distance:2mm Min(From solder joint to case) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO. LSD335/66-XX/RP38-PF Page 8/8 Reliability Test: Test Item Test Condition 1.Under Room Temperature 2.If=10mA 3.t=1000 hrs (-24hrs, +72hrs) Description This test is conducted for the purpose of detemining the resisance of a part in electrical and themal stressed. Reference Standard MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 Operating Life Test High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under ondition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. J IS C 7021: B-12 High Temperature High Humidity Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95% 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hous. MIL-STD-202:103B JIS C 7021: B-11 Thermal Shock Test 1.Ta=105 ℃±5 ℃&-40 ℃±5 ℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5℃ 2.Dwell time= 10 ±1sec. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=230 ℃±5℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2