APXH003A0X-SRZ_0910

Data Sheet October 8, 2009 Pico TLynxTM 3A: Non-Isolated DC-DC Power Modules 2.4 – 5.5Vdc input; 0.6Vdc to 3.63Vdc output; 3A Output Current Features Compliant to RoHS EU Directive 2002/95/EC (Z versions) Compatible in a Pb-free or SnPb reflow environment (Z versions) Wide Input voltage range (2.4Vdc-5.5Vdc) Output voltage programmable from 0.6Vdc to 3.63 Vdc via external resistor Tunable LoopTM to optimize dynamic output voltage response RoHS Compliant Applications EZ-SEQUENCE TM Flexible output voltage sequencing EZSEQUENCE – APTH versions Remote sense Fixed switching frequency Output overcurrent protection (non-latching) Overtemperature protection Remote On/Off Ability to sink and source current Cost efficient open frame design Small size: 12.2 mm x 12.2 mm x 6.25 mm Distributed power architectures Intermediate bus voltage applications Telecommunications equipment Servers and storage applications Networking equipment Industrial equipment Vin+ VIN VOUT SENSE RTUNE Vout+ (0.48 in x 0.48 in x 0.25 in) Wide operating temperature range (-40°C to 85°C) UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03 Certified, and VDE‡ 0805:2001-12 (EN60950-1) Licensed MODULE Cin SEQ CTUNE Q1 Co ON/OFF GND TRIM RTrim ISO** 9001 and ISO 14001 certified manufacturing facilities Description The Pico TLynxTM 3A power modules are non-isolated dc-dc converters that can deliver up to 3A of output current. These modules operate over a wide range of input voltage (VIN = 2.4Vdc-5.5Vdc) and provide a precisely regulated output voltage from 0.6Vdc to 3.63Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current and overtemperature protection, and output voltage sequencing (APTH versions). A new feature, the Tunable LoopTM , allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. * UL is a registered trademark of Underwriters Laboratories, Inc. † ‡ CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards Document No: DS06-131 ver. 1.11 PDF name: APTH003A0X_ds.pdf Data Sheet October 8, 2009 Pico TLynxTM 3A: Non-isolated DC-DC Power Modules 2.4 – 5.5Vdc input; 0.6Vdc to 3.63Vdc output; 3A output current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Input Voltage Continuous Sequencing Voltage Operating Ambient Temperature (see Thermal Considerations section) Storage Temperature All Tstg -55 125 °C APTH All VSEQ TA -0.3 -40 ViN, Max 85 Vdc °C Device All Symbol VIN Min -0.3 Max 6 Unit Vdc Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Operating Input Voltage Maximum Input Current (VIN=2.4V to 5.5V, IO=IO, max ) Input No Load Current (VIN = 5.0Vdc, IO = 0, module enabled) Input Stand-by Current (VIN = 5.0Vdc, module disabled) Inrush Transient Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN =0 to 5.5V, IO= IOmax ; See Test Configurations) Input Ripple Rejection (120Hz) All All All It 25 40 2 Device All All VO,set = 0.6 Vdc VO,set = 3.3Vdc All Symbol VIN IIN,max IIN,No load IIN,No load IIN,stand-by Min 2.4 Typ ⎯ Max 5.5 3.5 Unit Vdc Adc mA mA mA 26 75 2.1 1 As mAp-p dB 2 CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 5A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. LINEAGE POWER 2 Data Sheet October 8, 2009 Pico TLynxTM 3A: Non-isolated DC-DC Power Modules 2.4 – 5.5Vdc input; 0.6Vdc to 3.63Vdc output; 3A output current Electrical Specifications (continued) Parameter Output Voltage Set-point (with 0.5% tolerance for external resistor used to set output voltage) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation (for VO ≥ 2.5Vdc) Line (VIN=VIN, min to VIN, max) Load (IO=IO, min to IO, max) Output Regulation (for VO < 2.5Vdc) Line (VIN=VIN, min to VIN, max) Load (IO=IO, min to IO, max) Temperature (Tref=TA, min to TA, max) Remote Sense Range Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Co = 0.1μF // 10 μF ceramic capacitors) Peak-to-Peak (5Hz to 20MHz bandwidth) RMS External Capacitance ESR ≥ 1 mΩ With the Tunable Loop ESR ≥ 0.15 mΩ ESR ≥ 10 mΩ Output Current Output Current Limit Inception (Hiccup Mode ) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) Efficiency VIN= 3.3Vdc, TA=25°C IO=IO, max , VO= VO,set VIN= 5Vdc Switching Frequency Dynamic Load Response (dIo/dt=10A/μs; VIN = 5V; Vout = 1.5V, TA=25°C) Load Change from Io= 0% to 50% of Io,max; Co = 0 Peak Deviation Settling Time (Vo