AXH016A0X3Z

Data Sheet September 9, 2008 Austin SuperLynxTM SIP Non-isolated Power Modules: 3.0Vdc –5.5Vdc Input; 0.75Vdc to 3.63Vdc Output;16A Output Current RoHS Compliant Features Compliant to RoHS EU Directive 2002/95/EC (-Z versions) Compliant to ROHS EU Directive 2002/95/EC with lead solder exemption (non-Z versions) Delivers up to 16A output current High efficiency – 95% at 3.3V full load (VIN = 5.0V) Small size and low profile: 50.8 mm x 12.7 mm x 8.10 mm (2.00 in x 0.5 in x 0.32 in) Low output ripple and noise High Reliability: Calculated MTBF > 6.8M hours at 25 C Full-load Constant switching frequency (300 kHz) Output voltage programmable from 0.75 Vdc to 3.63Vdc via external resistor Line Regulation: 0.3% (typical) Load Regulation: 0.4% (typical) Temperature Regulation: 0.4 % (typical) Remote On/Off Remote Sense Output overcurrent protection (non-latching) Wide operating temperature range (-40°C to 85°C) UL* 60950-1Recognized, CSA† C22.2 No. ‡ 60950-1-03 Certified, and VDE 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities o Applications Distributed power architectures Intermediate bus voltage applications Telecommunications equipment Servers and storage applications Networking equipment Enterprise Networks Latest generation IC’s (DSP, FPGA, ASIC) and Microprocessor powered applications Description Austin SuperLynx SIP (Single In-line package) power modules are non-isolated dc-dc converters that can deliver up to 16A of output current with full load efficiency of 95.0% at 3.3V output. These modules provide a precisely regulated output voltage programmable via external resistor from 0.75Vdc to 3.63Vdc over a wide range of input voltage (VIN = 3.0 – 5.5Vdc). The open-frame construction and small footprint enable designers to develop costand space-efficient solutions. Standard features include remote On/Off, remote sense, programmable output voltage, overcurrent and overtemperature protection. TM * UL is a registered trademark of Underwriters Laboratories, Inc. † ‡ CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards Document No: DS03-085 ver. 1.52 PDF name: austin-superlynx-sip-ds.pdf Data Sheet September 9, 2008 Austin SuperLynxTM SIP Non-isolated Power Modules: 3.0 – 5.5Vdc Input; 0.75Vdc to 3.63Vdc Output; 16A output current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Input Voltage Continuous Operating Ambient Temperature (see Thermal Considerations section) Storage Temperature All Tstg -55 125 °C All TA -40 85 °C Device All Symbol VIN Min -0.3 Max 5.8 Unit Vdc Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Operating Input Voltage Maximum Input Current (VIN=3.0V to 5.5V, IO=IO, max ) Input No Load Current (VIN = 5.0Vdc, IO = 0, module enabled) Input Stand-by Current (VIN = 5.0Vdc, module disabled) Inrush Transient Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test Configurations) Input Ripple Rejection (120Hz) All All All It 100 30 2 Device Vo ≤ VIN - 0.5 All Vo = 0.75 Vdc Vo = 3.3 Vdc All Symbol VIN IIN,max IIN,No load IIN,No load IIN,stand-by Min 3.0 Typ ⎯ Max 5.5 16 Unit Vdc Adc mA mA mA 70 70 1.5 0.1 As mAp-p dB 2 CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a 20A, fast-acting, glass type fuse rated for 32V (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. LINEAGE POWER 2 Data Sheet September 9, 2008 Austin SuperLynxTM SIP Non-isolated Power Modules: 3.0 – 5.5Vdc Input; 0.75Vdc to 3.63Vdc Output; 16A output current Electrical Specifications (continued) Parameter Output Voltage Set-point (VIN=VIN, min, IO=IO, max, TA=25°C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) Load (IO=IO, min to IO, max) Temperature (Tref=TA, min to TA, max) Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Cout = 1μF ceramic//10μFtantalum capacitors) RMS (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) External Capacitance ESR ≥ 1 mΩ ESR ≥ 10 mΩ Output Current Output Current Limit Inception (Hiccup Mode ) (VO= 90% of VO, set) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) Efficiency VIN= VIN, nom, TA=25°C IO=IO, max , VO= VO,set VO,set = 0.75Vdc VO, set = 1.2Vdc VO,set = 1.5Vdc VO,set = 1.8Vdc VO,set = 2.5Vdc VO,set = 3.3Vdc Switching Frequency Dynamic Load Response (dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C) Load Change from Io= 50% to 100% of Io,max; 1μF ceramic// 10 μF tantalum Peak Deviation Settling Time (Vo