LT1738
Slew Rate Controlled
Ultralow Noise DC/DC Controller
U
DESCRIPTIO
FEATURES
■
■
■
■
■
■
■
■
■
The LT ®1738 is a switching regulator controller designed
to lower conducted and radiated electromagnetic interference (EMI). Ultralow noise and EMI are achieved by
controlling the voltage and current slew rates of an external N-channel MOSFET switch. Current and voltage slew
rates can be independently set to optimize harmonic
content of the switching waveforms vs efficiency. The
LT1738 can reduce high frequency harmonic power by as
much as 40dB with only minor losses in efficiency.
The LT1738 utilizes a current mode architecture optimized for single switch topologies such as boost, flyback
and Cuk. The IC includes gate drive and all necessary
oscillator, control and protection circuitry. Unique error
amp circuitry can regulate both positive and negative
voltages. The internal oscillator may be synchronized to
an external clock for more accurate placement of switching harmonics.
Greatly Reduced Conducted and Radiated EMI
Low Switching Harmonic Content
Independent Control of Output Switch Voltage and
Current Slew Rates
Greatly Reduced Need for External Filters
Single N-Channel MOSFET Driver
20kHz to 250kHz Oscillator Frequency
Easily Synchronized to External Clock
Regulates Positive and Negative Voltages
Easier Layout Than with Conventional Switchers
U
APPLICATIO S
■
■
■
■
■
■
Power Supplies for Noise Sensitive Communication
Equipment
EMI Compliant Offline Power Supplies
Precision Instrumentation Systems
Isolated Supplies for Industrial Automation
Medical Instruments
Data Acquisition Systems
Protection features include gate drive lockout for low VIN,
soft-start, output current limit, short-circuit current limiting, gate drive overvoltage clamp and input supply
undervoltage lockout.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Ultralow Noise 5V to 12V Converter
22µH
5V
VIN
MBRD620
P3
+
100µF
17
VIN
14
5
6
1.3nF
7
16.9k
25k
25k
3.3k
3.3k
22nF
0.22µF
8
16
15
12
B
4 × 150µF
OSCON
CAP
10µH
150µF
OSCON
A
+
12V
1A
OPTIONAL
3
GCL
SHDN
+
12V Output Noise
(Bandwidth = 100MHz)
5pF
POINT A
ON SCHEMATIC
500µV/DIV
2
V5
400µVP-P
SYNC
CT
GATE
1
Si9426
POINT B
ON SCHEMATIC
50mV/DIV
LT1738
RT
RVSL
CS
4
25mΩ
RCSL
PGND
VC
SS
1.5k
13
GND
11
FB
NFB
10
20
21.5k
9
5µs/DIV
1738 TA01a
2.5k
1738 TA01
10nF
1738fa
1
LT1738
W
U
PACKAGE/ORDER I FOR ATIO
U
W W
W
ABSOLUTE
U
AXI U RATI GS
(Note 1)
Supply Voltage (VIN) ................................................ 20V
Gate Drive Current ..................................... Internal Limit
V5 Current ................................................. Internal Limit
SHDN Pin Voltage .................................................... 20V
Feedback Pin Voltage (Trans. 10ms) ...................... ±10V
Feedback Pin Current ............................................ 10mA
Negative Feedback Pin Voltage (Trans. 10ms) ........ ±10V
CS Pin .......................................................................... 5V
GCL Pin ..................................................................... 16V
SS Pin .......................................................................... 3V
Operating Junction Temperature Range
(Note 3) ............................................ – 40°C to 125°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
TOP VIEW
GATE
1
20 PGND
CAP
2
19 NC
GCL
3
18 NC
CS
4
17 VIN
LT1738EG
LT1738IG
V5
5
16 RVSL
SYNC
6
15 RCSL
CT
7
14 SHDN
RT
8
13 SS
FB
9
12 VC
NFB 10
ORDER PART
NUMBER
11 GND
G PACKAGE
20-LEAD PLASTIC SSOP
TJMAX = 150°C, θJA = 110°C/ W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 12V, VC = 0.9V, VFB = VREF, RVSL, RCSL = 16.9k, RT = 16.9k and
other pins open unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
1.235
1.250
1.265
V
250
1000
nA
Error Amplifiers
VREF
Reference Voltage
Measured at Feedback Pin
●
IFB
Feedback Input Current
VFB = VREF
●
FBREG
Reference Voltage Line Regulation
2.7V ≤ VIN ≤ 20V
●
VNFR
Negative Feedback Reference Voltage
Measured at Negative Feedback Pin
with Feedback Pin Open
●
INFR
Negative Feedback Input Current
VNFB = VNFR
NFBREG
Negative Feedback Reference Voltage Line Regulation
2.7V ≤ VIN ≤ 20V
gm
Error Amplifier Transconductance
∆IC = ±50µA
0.012
0.03
%/V
–2.56
– 2.50
–2.45
V
–37
– 25
µA
0.009
0.03
%/V
1500
●
1100
700
2200
2500
µmho
µmho
●
IESK
Error Amp Sink Current
VFB = VREF + 150mV, VC = 0.9V
●
120
200
350
µA
IESRC
Error Amp Source Current
VFB = VREF – 150mV, VC = 0.9V
●
120
200
350
µA
VCLH
Error Amp Clamp Voltage
High Clamp, VFB = 1V
VCLL
Error Amp Clamp Voltage
Low Clamp, VFB = 1.5V
AV
Error Amplifier Voltage Gain
FBOV
FB Overvoltage Shutdown
ISS
Soft-Start Charge Current
1.27
V
0.12
V
250
V/V
Outputs Drivers Disabled
1.47
V
VSS = 1V
9.0
180
12
µA
1738fa
2
LT1738
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 12V, VC = 0.9V, VFB = VREF, RVSL, RCSL = 16.9k, RT = 16.9k and
other pins open unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
Oscillator Frequency = 250kHz
290
TYP
MAX
UNITS
Oscillator and Sync
fMAX
Max Switch Frequency
fSYNC
Synchronization Frequency Range
VSYNC
SYNC Pin Input Threshold
RSYNC
SYNC Pin Input Resistance
250
●
0.7
kHz
kHz
1.4
2
40
kΩ
90
93.5
%
10
7.6
10.4
7.9
10.7
8.1
V
V
0.2
0.35
V
Gate Drive
DCMAX
Maximum Switch Duty Cycle
RVSL = RCSL = 3.9k,
Osc Frequency = 25kHz
VGON
Gate On Voltage
VIN = 12, GCL = 12
VIN = 12, GCL = 8
VGOFF
Gate Off Voltage
VIN = 12V
IGSO
Max Gate Source Current
VIN = 12V
0.3
A
IGSK
Max Gate Sink Current
VIN = 12V
0.3
A
VINUVLO
Gate Drive Undervoltage Lockout (Note 5)
VGCL = 6.5V
●
7.3
7.5
V
Current Sense
tIBL
Switch Current Limit Blanking Time
VSENSE
Sense Voltage Shutdown Voltage
VSENSEF
Sense Voltage Fault Threshold
100
VC Pulled Low
●
86
ns
103
120
mV
220
300
mV
Slew Control for the Following Slew Tests See Test Circuit in Figure 1b
VSLEWR
Output Voltage Slew Rising Edge
RVSL = RCSL = 17k
26
V/µs
VSLEWF
Output Voltage Slew Falling Edge
RVSL = RCSL = 17k
19
V/µs
VISLEWR
Output Current Slew Rising Edge (CS pin V)
RVSL = RCSL = 17k
2.1
V/µs
VISLEWF
Output Current Slew Falling Edge (CS pin V)
RVSL = RCSL = 17k
2.1
V/µs
Supply and Protection
VINMIN
Minimum Input Voltage (Note 4)
VGCL = VIN
IVIN
Supply Current (Note 3)
RVSL = RCSL = 17k
RVSL = RCSL = 17k
VSHDN
Shutdown Turn-On Threshold
●
∆VSHDN
Shutdown Turn-On Voltage Hysteresis
●
VIN = 12
VIN = 20
●
2.55
3.6
V
●
12
35
40
55
mA
mA
1.31
1.39
1.48
V
50
110
180
mV
ISHDN
Shutdown Input Current Hysteresis
10
24
35
µA
V5
5V Reference Voltage
6.5V ≤ VIN ≤ 20V, IV5 = 5mA
6.5V ≤ VIN ≤ 20V, IV5 = – 5mA
4.85
4.80
5
5
5.20
5.15
V
V
IV5SC
5V Reference Short-Circuit Current
VIN = 6.5V Source
VIN = 6.5V Sink
10
–10
●
Note 1: Absolute Maximum Ratings are those values beyond which the
life of a device may be impaired.
Note 2: Supply current specification includes loads on each gate as in
Figure 1a. Actual supply currents vary with operating frequency, operating
voltages, V5 load, slew rates and type of external FET.
Note 3: The LT1738E is guaranteed to meet performance specifications
from 0°C to 70°C. Specifications from –40°C to 125°C are assured by
mA
mA
design, characterization and correlation with statistical process
controls.The LT1738I is guaranteed and tested to meet performance
specifications from – 40°C to 125°C.
Note 4: Output gate drive is enabled at this voltage. The GCL voltage will
also determine driver activity.
Note 5: Gate drive is ensured to be on when VIN is greater than max value.
1738fa
3
LT1738
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Negative Feedback Voltage and
Input Current vs Temperature
2.480
3.2
1.258
700
2.485
3.0
1.256
650
2.490
2.8
1.254
600
1.252
550
2.495
2.6
1.250
500
2.500
2.4
1.248
450
2.505
2.2
1.246
400
2.510
2.0
1.244
350
1.242
300
2.515
1.8
1.240
–50 –25
0
NEGATIVE FEEDBACK VOLTAGE (V)
750
2.520
–50 –25
250
25 50 75 100 125 150
TEMPERATURE (°C)
0
1.6
25 50 75 100 125 150
TEMPERATURE (°C)
1738 G01
Feedback Overvoltage Shutdown
vs Temperature
Error Amp Transconductance vs
Temperature
Error Amp Output Current vs
Feedback Pin Voltage from Nominal
500
1900
400
1800
300
1700
200
1.55
1.50
1.45
1.40
1.35
1.30
1.25
1.20
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
CURRENT (µA)
2000
1.65
TRANSCONDUCTANCE (µmho)
FEEDBACK VOLTAGE (V)
1738 G02
1.70
1.60
1600
1500
1400
–300
1100
–400
1738 G03
SHDN Pin On and Off Thresholds
vs Temperature
1.50
240
CLAMP
220
1.0
0.8
0.6
0.4
THRESHOLD
FAULT
1.45
SHDN PIN VOLTAGE (V)
CS PIN VOLTAGE (mV)
VC PIN VOLTAGE (V)
1738 G05
CS Pin Trip Voltage and CS Fault
Voltage vs Temperature
1.4
200
180
160
140
120
ON
1.40
1.35
1.30
TRIP
0.2
0
–50 –25
–500
–400 –300 –200 –100 0 100 200 300 400
FEEDBACK PIN VOLTAGE FROM NOMINAL (mV)
1738 G04
VC Pin Threshold and Clamp
Voltage vs Temperature
1.2
125°C
–100
–200
25 50 75 100 125 150
TEMPERATURE (°C)
25°C
0
1200
0
–40°C
100
1300
1000
–50 –25
NFB INPUT CURRENT (µA)
1.260
FB INPUT CURRENT (nA)
FEEDBACK VOLTAGE (V)
Feedback Voltage and Input
Current vs Temperature
OFF
100
0
25 50 75 100 125 150
TEMPERATURE (°C)
1738 G06
80
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
1738 G07
1.25
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
1738 G08
1738fa
4
LT1738
U W
TYPICAL PERFOR A CE CHARACTERISTICS
SHDN Pin Hysteresis Current vs
Temperature
27
21
19
17
0
25 50 75 100 125 150
TEMPERATURE (°C)
VIN = 20 RVSL, RCSL = 17k
14
13
VIN = 12 RVSL, RCSL = 17k
0.2
GATE DRIVE A/B PIN VOLTAGE (V)
PERCENT OF MAX CS VOLTAGE
80
70
60
40
60
DUTY CYCLE (%)
80
100
10.6
GCL = 12V
10.5
6.5
0.50
6.4
0.45
6.2
10.3
6.1
VIN = 12V
NO LOAD
10.2
6.0
10.1
5.9
10.0
5.8
GCL = 6V
9.90
5.7
9.80
5.6
9.70
–50 –25
9.3
0.25
0.20
0.15
0.10
0.05
5.5
0
25 50 75 100 125 150
TEMPERATURE (°C)
0
–50 –25
V5 Voltage vs Load Current
5.08
5.06
8.7
8.5
8.3
8.1
7.9
6.4
7.7
0
25 50 75 100 125 150
TEMPERATURE (°C)
1738 G15
25 50 75 100 125 150
TEMPERATURE (°C)
SS VOLTAGE = 0.9V
8.9
6.5
6.3
–50 –25
0
1738 G14
V5 PIN VOLTAGE (V)
6.6
VIN = 12V
NO LOAD
0.30
9.1
SS PIN CURRENT (µA)
7.1
120
0.35
9.5
GCL = 6V
6.7
100
0.40
Soft-Start Current vs Temperature
7.3
6.8
40
60
80
CS PIN VOLTAGE (mV)
1738 G13
Gate Drive Undervoltage Lockout
Voltage vs Temperature
6.9
20
1738 G11
6.3
10.4
1738 G12
7.0
0
Gate Drive Low Voltage vs
Temperature
10.7
90
7.2
0
Gate Drive High Voltage vs
Temperature
VC PIN = 0.9V
TA = 25°C
20
0.6
1738 G10
110
0
0.8
11 USING LOAD OF FIGURE 1A
fOSC = 120kHz
10
–50 –25 0
25 50 75 100 125 150
TEMPERATURE (°C)
Slope Compensation
50
1.0
0.4
1738 G09
100
1.2
12
GATE DRIVE A/B PIN VOLTAGE (V)
15
–50 –25
15
VC PIN VOLTAGE (V)
16
23
TA = 25°C
1.4
VIN = 12 RVSL, RCSL = 4.85k
17
VIN CURRENT (mA)
SHDN PIN CURRENT (µA)
1.6
18
25
VIN PIN VOLTAGE (V)
CS Pin to VC Pin Transfer
Function
VIN Current vs Temperature
7.5
–50 –25
T = 125°C
5.04
5.02
T = 25°C
5.00
T = –40°C
4.98
0
25 50 75 100 125 150
TEMPERATURE (°C)
1738 G16
4.96
–15
–10
–5
0
5
LOAD CURRENT (mA)
10
15
1738 G17
1738fa
5
LT1738
U
U
U
PI FU CTIO S
Part Supply
V5 (Pin 5): This pin provides a 5V output that can sink or
source 10mA for use by external components. V5 source
current comes from VIN . Sink current goes to GND. VIN
must be greater than 6.5V in order for this voltage to be in
regulation. If this pin is used, a small capacitor ( VGCL + 0.8V. If this pin
is tied to VIN, then undervoltage lockout is disabled.
There is an internal 19V zener tied from this pin to ground
to provide a fail-safe for maximum gate voltage.
Slew Control
CAP (Pin 2): This pin is the feedback node for the external
voltage slewing capacitor. Normally a small 1pf to 5pf
capacitor is connected from this pin to the drain of the
MOSFET.
The voltage slew rate is inversely proportional to this
capacitance and proportional to the current that the part
will sink and source on this pin. That current is inversely
proportional to RVSL.
RCSL (Pin 15): A resistor to ground sets the current slew
rate for the external drive MOSFET during switching. The
minimum resistor value is 3.3k and the maximum value is
68k. The time to slew between on and off states of the
MOSFET current will determine how the di/dt related
harmonics are reduced. This time is proportional to RCSL
and RS (the current sense resistor) and maximum current.
Longer times produce a greater reduction of higher frequency harmonics.
RVSL (Pin 16): A resistor to ground sets the voltage slew
rate for the drain of the external drive MOSFET. The
minimum resistor value is 3.3k and the maximum value is
68k. The time to slew between on and off states on the
MOSFET drain voltage will determine how dv/dt related
harmonics are reduced. This time is proportional to RVSL,
CV and the input voltage. Longer times produce more
rolloff of harmonics. CV is the equivalent capacitance from
CAP to the drain of the MOSFET.
Switch Mode Control
SS (Pin 3): The SS pin allows for ramping of the switch
current threshold at startup. Normally a capacitor is placed
on this pin to ground. An internal 9µA current source will
charge this capacitor up. The voltage on the VC pin cannot
exceed the voltage on SS. Thus peak current will ramp up
as the SS pin ramps up. During a short circuit fault the SS
pin will be discharged to ground thus reinitializing softstart.
When SS is below the VC clamp voltage the VC pin will
closely track the SS pin.
This pin can be left open if not used.
CS (Pin 4): This is the input to the current sense amplifier.
It is used for both current mode control and current
slewing of the external MOSFET. Current sense is accomplished via a sense resistor (RS) connected from the
source of the external MOSFET to ground. CS is connected
to the top of RS. Current sense is referenced to the GND
pin.
The switch maximum operating current will be equal to
0.1V/RS. At CS = 0.1V, the gate driver will be immediately
turned off (no slew control).
If CS = 0.22V in addition to the drivers being turned off, VC
and SS will be discharged to ground (short-circuit protection). This will hasten turn off on subsequent cycles.
FB (Pin 9): The feedback pin is used for positive voltage
sensing. It is the inverting input to the error amplifier. The
noninverting input of this amplifier connects internally to
a 1.25V reference.
If the voltage on this pin exceeds the reference by 220mV,
then the output driver will immediately turn off the external
MOSFET (no slew control). This provides for output overvoltage protection
When this input is below 0.9V then the current sense
blanking will be disabled. This will assist start up.
NFB (Pin 10): The negative feedback pin is used for
sensing a negative output voltage. The pin is connected to
the inverting input of the negative feedback amplifier
through a 100k source resistor. The negative feedback
amplifier provides a gain of –0.5 to the FB pin. The nominal
regulation point would be –2.5V on NFB. This pin should
be left open if not used.
If NFB is being used then overvoltage protection will occur
at 0.44V below the NFB regulation point.
At NFB < –1.8 current sense blanking will be disabled.
1738fa
7
LT1738
U
U
U
PI FU CTIO S
TEST CIRCUITS
VC (Pin 12): The compensation pin is used for frequency
compensation and current limiting. It is the output of the
error amplifier and the input of the current comparator.
Loop frequency compensation can be performed with an
RC network connected from the VC pin to ground. The
voltage on VC is proportional to the switch peak current.
The normal range of voltage on this pin is 0.25V to 1.27V.
However, during slope compensation the upper clamp
voltage is allowed to increase with the compensation.
During a short-circuit fault the VC pin will be discharged to
ground.
0.9A
20mA
5pF
5pF
IN5819
IN5819
CAP
CAP
GATE
GATE
Si4450DY
ZVN3306A
2
CS
+
–
10
0.1
10
+
–
1738 F01b
1738 F01a
Figure 1a. Typical Test Circuitry Figure 1b. Test Circuit for Slew
W
BLOCK DIAGRA
SHDN
VIN
V5
RCSL
RVSL
14
17
5
15
16
TO
DRIVERS
+
REGULATOR
NEGATIVE
FEEDBACK
AMP
–
100k
3 GCL
VREG
50k
NFB 10
2 CAP
–
FB 9
+
1 GATE
ERROR
AMP
SLEW
CONTROL
+
1.25V
VC 12
20 PGND
–
+
COMP
SS 13
4 CS
SENSE
AMP
+
–
S
Q
FF
RT 8
R
OSCILLATOR
SUB
CT 7
6
11
SYNC
GND
1738 BD
1738fa
8
LT1738
U
OPERATIO
In noise sensitive applications switching regulators tend
to be ruled out as a power supply option due to their
propensity for generating unwanted noise. When switching supplies are required due to efficiency or input/output
constraints, great pains must be taken to work around the
noise generated by a typical supply. These steps may
include pre and post regulator filtering, precise synchronization of the power supply oscillator to an external clock,
synchronizing the rest of the circuit to the power supply
oscillator or halting power supply switching during noise
sensitive operations. The LT1738 greatly simplifies the
task of eliminating supply noise by enabling the design of
an inherently low noise switching regulator power supply.
transconductance amplifier that integrates the difference
between the feedback output voltage and an internal
1.25V reference. The output of the error amp adjusts the
switch current trip point to provide the required load
current at the desired regulated output voltage. This
method of controlling current rather than voltage provides faster input transient response, cycle-by-cycle
current limiting for better output switch protection and
greater ease in compensating the feedback loop. The VC
pin is used for loop compensation and current limit
adjustment. During normal operation the VC voltage will
be between 0.25V and 1.27V. An external clamp on VC or
SS may be used for lowering the current limit.
The LT1738 is a fixed frequency, current mode switching
regulator with unique circuitry to control the voltage and
current slew rates of the output switch. Current mode
control provides excellent AC and DC line regulation and
simplifies loop compensation.
The negative voltage feedback amplifier allows for direct
regulation of negative output voltages. The voltage on the
NFB pin gets amplified by a gain of – 0.5 and driven on to
the FB input, i.e., the NFB pin regulates to –2.5V while the
amplifier output internally drives the FB pin to 1.25V as in
normal operation. The negative feedback amplifier input
impedance is 100k (typ) referred to ground.
Slew control capability provides much greater control
over the power supply components that can create conducted and radiated electromagnetic interference. Compliance with EMI standards will be an easier task and will
require fewer external filtering components.
The LT1738 uses an external N-channel MOSFET as the
power switch. This allows the user to tailor the drive
conditions to a wide range of voltages and currents.
CURRENT MODE CONTROL
Referring to the block diagram. A switching cycle begins
with an oscillator discharge pulse, which resets the RS
flip-flop, turning on the GATE driver and the external
MOSFET. The switch current is sensed across the external
sense resistor and the resulting voltage is amplified and
compared to the output of the error amplifier (VC pin). The
driver is turned off once the output of the current sense
amplifier exceeds the voltage on the VC pin. In this way
pulse by pulse current limit is achieved.
Internal slope compensation is provided to ensure stability under high duty cycle conditions.
Output regulation is obtained using the error amp to set
the switch current trip point. The error amp is a
Soft-Start
Control of the switch current during start up can be
obtained by using the SS pin. An external capacitor from
SS to ground is charged by an internal 9µA current source.
The voltage on VC cannot exceed the voltage on SS. Thus
as the SS pin ramps up the VC voltage will be allowed to
ramp up. This will then provide for a smooth increase in
switch maximum current. SS will be discharged as a result
of the CS voltage exceeding the short circuit threshold of
approximately 0.22V.
Slew Control
Control of output voltage and current slew rates is achieved
via two feedback loops. One loop controls the MOSFET
drain dV/dt and the other loop controls the MOSFET dI/dt.
The voltage slew rate uses an external capacitor between
CAP and the MOSFET drain. This integrating cap closes the
voltage feedback loop. The external resistor RVSL sets the
current for the integrator. The voltage slew rate is thus
inversely proportional to both the value of capacitor and
RVSL.
1738fa
9
LT1738
U
OPERATIO
The current slew feedback loop consists of the voltage
across the external sense resistor, which is internally
amplified and differentiated. The derivative is limited to a
value set by RCSL. The current slew rate is thus inversely
proportional to both the value of sense resistor and RCSL.
The two control loops are combined internally so that a
smooth transition from current slew control to voltage
slew control is obtained. When turning on, the driver
current will slew before voltage. When turning off, voltage
will slew before current. In general it is desirable to have
RVSL and RCSL of similar value.
Internal Regulator
Most of the control circuitry operates from an internal 2.4V
low dropout regulator that is powered from VIN. The
internal low dropout design allows VIN to vary from 2.7V
to 20V with stable operation of the controller. When SHDN
< 1.3V the internal regulator is completely disabled.
5V Regulator
A 5V regulator is provided for powering external circuitry.
This regulator draws current from VIN and requires VIN to
be greater than 6.5V to be in regulation. It can sink or
source 10mA. The output is current limited to prevent
against destruction from accidental short circuits.
Safety and Protection Features
There are several safety and protection features on the
chip. The first is overcurrent limit. Normally the gate driver
will go low when the output of the internal sense amplifier
exceeds the voltage on the VC pin. The VC pin is clamped
such that maximum output current is attained when the CS
pin voltage is 0.1V. At that level the outputs will be
immediately turned off (no slew). The effect of this control
is that the output voltage will foldback with overcurrent.
In addition, if the CS voltage exceeds 0.22V, the VC and SS
pins will be discharged to ground, resetting the soft-start
function. Thus if a short is present this will allow for faster
MOSFET turnoff and less MOSFET stress.
If the voltage on the FB pin exceeds regulation by approximately 0.22V, the outputs will immediately go low. The
implication is that there is an overvoltage fault.
The voltage on GCL determines two features. The first is
the maximum gate drive voltage. This will protect the
MOSFET gate from overvoltage.
With GCL tied to a zener or an external voltage source then
the maximum gate driver voltage is approximately
VGCL␣ – 0.2V. If GCL is tied to VIN, then the maximum gate
voltage is determined by VIN and is approximately
VIN – 1.6V. There is an internal 19V zener on the GCL pin
that prevents the gate driver pin from exceeding approximately 19V.
In addition, the GCL voltage determines undervoltage
lockout of the gate drive. This feature disables the gate
driver if VIN is too low to provide adequate voltage to turn
on the MOSFET. This is helpful during start up to insure the
MOSFET has sufficient gate drive to saturate.
If GCL is tied to a voltage source or zener less than 6.8V,
the gate driver will not turn on until VIN exceeds GCL
voltage by 0.8V. For VGCL above 6.5V, the gate drive is
insured to be off for VIN < 7.3V and it will be turned on by
VGCL + 0.8V.
If GCL is tied to VIN, the gate driver is always on
(undervoltage lockout is disabled).
The gate drive has current limits for the drive currents. If
the sink or source current is greater than 300mA then the
current will be limited.
The V5 regulator also has internal current limiting that will
only guarantee ±10mA output current.
There is also an on chip thermal shutdown circuit that will
turn off the output in the event the chip temperature rises
to dangerous levels. Thermal shutdown has hysteresis
that will cause a low frequency ( VREG + 0.22V
(Output Overvoltage)
Immediately Goes Low
Overridden
None
GCL Clamp
Set Max Gate Voltage to Prevent
FET Gate Breakdown
Limits Max Voltage
None
None
Gate Drive
Undervoltage Lockout
Disable Gate Drive When VIN
Is Too Low. Set Via GCL Pin
Immediately Goes Low
Overridden
None
Thermal Shutdown
Turn Off Driver If Chip
Temperature Is Too Hot
Immediately Goes Low
Overridden
None
VIN Undervoltage Lockout
Disable Part When VIN ≅ 2.55V
Immediately Goes Low
Overridden
None
Gate Drive Source and Sink Current Limit
Limit Gate Drive Current
Limit Drive Current
None
None
V5 Source/Sink Current Limit
Limit Current from V5
None
None
None
Shutdown
Disable Part When SHDN VGCL + 0.8V. This could be used to bias a zener.
The GCL pin has an internal 19V zener to ground that will
provide a failsafe for maximum gate voltage.
As an example say we are using a Siliconix Si4480DY
which has RDS(ON) rated at 6V. To get 6V, VGCL needs to
be set to 6.2V and VIN needs to be at least 7.6V.
Gate Driver Considerations
In general, the MOSFET should be positioned as close to
the part as possible to minimize inductance.
When the part is active the gate drive will be pulled low to
less than 0.2V. When the part is off, the gate drive contains
a 40k resistor in series with a diode to ground that will offer
passive holdoff protection. If you are using some logic
level MOSFETs this might not be sufficient. A resistor may
be placed from gate to ground, however the value should
be reasonably high to minimize DC losses and possible AC
issues.
The gate drive source current comes from VIN. The sink
current exits through PGND. In general the decoupling cap
should be placed close to these two pins.
Switching Diodes
In general, switching diodes should be Schottky diodes.
Size and breakdown voltage depend on the specific converter. A lower forward drop will improve converter efficiency. No other special requirements are needed.
PCB LAYOUT CONSIDERATIONS
As with any switcher, careful consideration should be given
to PC board layout. Because this part reduces high frequency EMI, the board layout is less critical. However, high
currents and voltages still produce the need for careful
board layout to eliminate poor and erratic performance.
Basic Considerations
Keep the high current loops physically small in area. The
main loops are shown in Figure 6: the power switch loops
(A) and the rectifier loop (B). These loops can be kept small
by physically keeping the components close to one another. In addition, connection traces should be kept wide
to lower resistance and inductances. Components should
be placed to minimize connecting paths. Careful attention
to ground connections must also be maintained. Be careful that currents from different high current loops do not
get coupled into the ground paths of other loops. Using
singular points of connection for the grounds is the best
way to do this. The two major points of connection are the
bottom of the input decoupling capacitor and the bottom
of the output decoupling capacitor. Typically, the sense
resistor device PGND and device GND will tie to the bottom
of the input capacitor.
VIN
CIN
•
A
•
B
COUT VOUT
GATE
CS
1738 F06
Figure 6
1738fa
18
LT1738
U
U
W
U
APPLICATIO S I FOR ATIO
There are two other loops to pay attention to. The current
slew involves a high bandwidth control that goes through
the MOSFET switch, the sense resistor and into the CS pin
of the part and out the GATE pin to the MOSFET. Trace
inductance and resistance should be kept low on the GATE
drive trace. The CS trace should have low inductance.
MORE HELP
AN70 contains information about low noise switchers and
measurement of noise and should be consulted. AN19 and
AN29 also have general knowledge concerning switching
regulators. Also, our Application Department is always
ready to lend a helping hand.
Finally, care should be taken with the CAP pin. The part will
tolerate stray capacitance to ground on this pin (