LTC3225EDDB#TRMPBF

LTC3225/LTC3225-1 150mA Supercapacitor Charger FEATURES DESCRIPTION n The LTC®3225/LTC3225-1 are programmable supercapacitor chargers designed to charge two supercapacitors in series to a selectable fixed output voltage (4.8V/5.3V for the LTC3225 and 4V/4.5V for the LTC3225-1) from input supplies as low as 2.8V to 5.5V. Automatic cell balancing prevents overvoltage damage to either supercapacitor. No balancing resistors are required. n n n n n n n n n Low Noise Constant Frequency Charging of Two Series Supercapacitors Automatic Cell Balancing Prevents Capacitor Overvoltage During Charging Programmable Charge Current (Up to 150mA) Selectable 2.4V or 2.65V Regulation per Cell (LTC3225) Selectable 2V or 2.25V Regulation per Cell (LTC3225-1) Automatic Recharge IVIN = 20μA in Standby Mode ICOUT < 1μA When Input Supply is Removed No Inductors Tiny Application Circuit (2mm × 3mm DFN Package, All Components CBOT) Charging Profile with 30% Mismatch in Output Capacitance (CTOP < CBOT) SHDN 5V/DIV SHDN 5V/DIV SHDN 5V/DIV IVIN 300mA/DIV IVIN 300mA/DIV IVIN 300mA/DIV VCOUT 2V/DIV VCOUT 2V/DIV VCOUT 2V/DIV VTOP-VBOT 200mV/DIV VTOP-VBOT 200mV/DIV VTOP-VBOT 500mV/DIV 2 SEC/DIV LTC3225 VSEL = VIN RPROG = 12k CTOP = CBOT = 1.1F CTOP INITIAL VOLTAGE = 1V CBOT INITIAL VOLTAGE = 1.3V 3225 G10 5 SEC/DIV LTC3225 VSEL = VIN RPROG = 12k CTOP = 1.43F CBOT = 1.1F CTOP INITIAL VOLTAGE = 0V CBOT INITIAL VOLTAGE = 0V 3225 G11 5 SEC/DIV LTC3225 VSEL = VIN RPROG = 12k CTOP = 1.1F CBOT = 1.43F CTOP INITIAL VOLTAGE = 0V CBOT INITIAL VOLTAGE = 0V 3225 G12 PIN FUNCTIONS C+ (Pin 1): Flying Capacitor Positive Terminal. A 1μF X5R or X7R ceramic capacitor should be connected from C+ to C–. C– (Pin 2): Flying Capacitor Negative Terminal. CX (Pin 3): Midpoint of Two Series Supercapacitors. This pin voltage is monitored and forced to track COUT (CX = COUT/2) during charging to achieve voltage balancing of the top and bottom supercapacitors. SHDN (Pin 4): Active Low Shutdown Input. A low on SHDN puts the LTC3225/LTC3225-1 in low current shutdown mode. Do not float the SHDN pin. PGOOD (Pin 5): Open-Drain Output Status Indicator. Upon start-up, this open-drain pin remains low until the output voltage, VOUT, is within 6% (typical) of its final value. Once VOUT is valid, PGOOD becomes Hi-Z. If VOUT falls 7.2% (typical) below its correct regulation level, PGOOD is pulled low. PGOOD may be pulled up through an external resistor to an appropriate reference level. This pin is Hi-Z in shutdown mode. VSEL (Pin 6): Output Voltage Selection Input. A logic low at VSEL sets the regulated COUT to 4.8V (LTC3225) or 4V (LTC3225-1); a logic high sets the regulated COUT to 5.3V (LTC3225) or 4.5V (LTC3225-1). Do not float the VSEL pin. PROG (Pin 7): Charge Current Programming Pin. A resistor connected between this pin and GND sets the charge current. (See Applications Information section). GND (Pin 8, Exposed Pad Pin 11): Charge Pump Ground. These pins must be soldered directly to PCB ground. The exposed pad must be soldered to a low impedance PCB ground for rated thermal performance. VIN (Pin 9): Power Supply for the LTC3225/LTC3225-1. VIN should be bypassed to GND with a low ESR ceramic capacitor of more than 2.2μF. COUT (Pin 10): Charge Pump Output Pin. Connect COUT to the top plate of the top supercapacitor. COUT provides charge current to the supercapacitors and regulates the final voltage to 4.8V/5.3V (LTC3225) or 4V/4.5V (LTC3225-1). 3225fb 5 LTC3225/LTC3225-1 SIMPLIFIED BLOCK DIAGRAM CFLY 9 1 2 C+ VIN 4 C– VIN SHDN SOFT-START AND SHUTDOWN CONTROL UVLO THERMAL PROTECTION 3000i POR 1.2V COUT CX CHARGE PUMP RUN CTOP 3 CBOT GND 8 i 7 10 PROG CLK RPROG RUN/STOP R1 OSCILLATOR – C1 R2 + VREF – 2% 1.2V PGOOD VREF + 1.088V (LTC3225) 1.067V (LTC3225-1) 6 POR VREF – 6% VSEL VREF – 7.2% 5 C2 – 3225 F01 Figure 1 OPERATION The LTC3225/LTC3225-1 are dual cell supercapacitor chargers. Their unique topology maintains a constant output voltage with programmable charge current. Their ability to maintain equal voltages on both cells while charging protects the supercapacitors from damage that is possible with other charging methods, without the use of external balancing resistors. The LTC3225/LTC3225-1 include an internal switched capacitor charge pump to boost VIN to a regulated output voltage. A unique architecture maintains relatively constant input current for the lowest possible input noise. The basic charger circuit requires only three external components. Normal Charge Cycle Operation begins when the SHDN pin is pulled above 1.3V. The COUT pin voltage is sensed and compared with a preset voltage threshold using an internal resistor divider and a comparator. The preset voltage threshold is selectable with the VSEL pin. If the voltage at the COUT pin is lower than the preset voltage threshold, the oscillator is enabled. The oscillator operates at a typical frequency of 0.9MHz. When the oscillator is enabled, the charge pump operates charging up COUT. Each time the charge pump starts up from shutdown, the input current drawn by the internal charge pump ramps up at approximately 20mA/μs until it reaches a level which is determined by RPROG. 3225fb 6 LTC3225/LTC3225-1 OPERATION Once the output voltage is charged to the preset voltage threshold, the part shuts down the internal charge pump and enters into a low current state. In this state, the LTC3225/LTC3225-1 consume only about 20μA from the input supply. The current drawn from COUT is approximately 2μA. Automatic Cell Balancing Due to manufacturing tolerances, capacitance and leakage current can vary from supercapacitor to supercapacitor. Without the automatic cell balancing scheme used in the LTC3225/LTC3225-1, the voltages across the supercapacitors could differ from each other and potentially overvoltage a cell. This can affect the performance and lifetime of a supercapacitor. The LTC3225/LTC3225-1 constantly monitor the voltage across both supercapacitors while charging. When the voltage across the supercapacitors is equal, both capacitors are charged with equal currents. If the voltage across one supercapacitor is lower than the other, the lower supercapacitor’s charge current is increased and the higher supercapacitor’s charge current is decreased. The greater the difference between the supercapacitor voltages, the greater the difference in charge current per capacitor. The charge currents can increase or decrease as much as 50% to balance the voltage across the supercapacitors. When the cell voltages are balanced, the supercapacitors are charged at a rate of approximately: 1 ICOUT = •IVIN 2 If the leakage currents or capacitances of the two supercapacitors are mismatched enough that varying the charge current is not sufficient to balance their voltages, the LTC3225/LTC3225-1 stop charging the capacitor with the higher voltage until they are again balanced. This feature protects either capacitor from experiencing an overvoltage condition. Attempting to equalize the voltages using parallel resistors wastes power, discharges the supercapacitors, and takes time to equalize the voltages. A 30% capacitance mismatch leads to a 30% initial voltage difference after charging. It takes hours to equalize the voltages across 1F supercapacitors using 10k resistors. Shutdown Mode Asserting SHDN low causes the LTC3225/LTC3225-1 to enter shutdown mode. With the SHDN pin connected to VIN and the input supply removed or grounded, less than 1μA is consumed from the output, allowing the supercapacitors to remain charged. If the input supply is present at VIN and the SHDN pin is grounded, the LTC3225/LTC3225-1 draw approximately 1μA of supply current. With the voltage at the COUT pin discharged to 0V, this current drops to less than 1μA. Since the SHDN pin is a high impedance CMOS input, it should never be allowed to float. Output Voltage Programming The LTC3225/LTC3225-1 have a VSEL input pin that allows the user to set the output threshold voltage to either 4.8V or 5.3V for the LTC3225 and 4V or 4.5V for the LTC3225-1 by forcing a low or high at the VSEL pin respectively. Output Status Indicator (PGOOD) During shutdown, the PGOOD pin is high impedance. When the charge cycle starts, an internal N-channel MOSFET pulls the PGOOD pin to ground. When the output voltage, VOUT, is within 6% (typical) of its final value, the PGOOD pin becomes high impedance, but charge current continues to flow until VOUT crosses the charge termination voltage. When VOUT drops 7% below the charge termination voltage, the PGOOD pin again pulls low. Current Limit/Thermal Protection The LTC3225/LTC3225-1 have built-in current limit as well as overtemperature protection. If the PROG pin is shorted to ground, a protection circuit automatically shuts off the internal charge pump. At higher temperatures, or if the input voltage is high enough to cause excessive self-heating of the part, the thermal shutdown circuitry shuts down the charge pump once the junction temperature exceeds approximately 150°C. It will enable the charge pump once the junction temperature drops back to approximately 135°C. The LTC3225/LTC3225-1 are able to cycle in and out of thermal shutdown indefinitely without latch-up or damage until the overcurrent condition is removed. 3225fb 7 LTC3225/LTC3225-1 APPLICATIONS INFORMATION Programming Charge Current Charging Time Estimation The charge current is programmed with a single resistor connecting the PROG pin to ground. The program resistor and the input/output charge currents are calculated using the following equations: The estimated charging time with equal initial voltages across the two supercapacitors is given by the equation: IVIN = 3600V RPROG IOUT = IVIN (with matched output capacitors) 2 An RPROG resistor value of 2k or less (i.e., short circuit) causes the LTC3225/LTC3225-1 to enter overcurrent shutdown mode. This mode prevents damage to the part by shutting down the internal charge pump. Power Efficiency The power efficiency (η) of the LTC3225/LTC3225-1 is similar to that of a linear regulator with an effective input voltage of twice the actual input voltage. In an ideal regulating voltage doubler the power efficiency is given by: η2xIDEAL = POUT VOUT •IOUT VOUT = = PIN VIN • 2IOUT 2VIN At moderate to high output power the switching losses and quiescent current of the LTC3225/LTC3225-1 are negligible and the above expression is valid. For example, with VIN = 3.6V, IOUT = 100mA and VOUT regulated to 5.3V, the measured efficiency is 71.2% which is in close agreement with the theoretical 73.6% calculation. Effective Open-Loop Output Resistance (ROL) The effective open-loop output resistance (ROL) of a charge pump is an important parameter that describes the strength of the charge pump. The value of this parameter depends on many factors including the oscillator frequency (fOSC), value of the flying capacitor (CFLY), the non-overlap time, the internal switch resistances (RS) and the ESR of the external capacitors. t CHRG = COUT • ( VCOUT – VINI) IOUT where COUT is the series output capacitance, VCOUT is the voltage threshold set by the VSEL pin, VINI is the initial voltage at the COUT pin and IOUT is the output charge current given by: IOUT = 1800V RPROG When the charging process starts with unequal initial voltages across the supercapacitors, only the capacitor with the lower voltage level is charged; the other capacitor is not charged until the voltages equalize. This extends the charging time slightly. Under the worst-case condition, whereby one capacitor is fully depleted while the other remains fully charged due to significant leakage current mismatch, the charging time is about 1.5 times longer than normal. Thermal Management For higher input voltages and maximum output current, there can be substantial power dissipation in the LTC3225/ LTC3225-1. If the junction temperature increases above approximately 150°C, the thermal shutdown circuitry automatically deactivates the output. To reduce the maximum junction temperature, a good thermal connection to the PC board is recommended. Connecting the GND pin (Pin 8) and the Exposed Pad (Pin 11) of the DFN package to a ground plane under the device on two layers of the PC board can reduce the thermal resistance of the package and PC board considerably. 3225fb 8 LTC3225/LTC3225-1 APPLICATIONS INFORMATION VIN Capacitor Selection The type and value of CIN controls the amount of ripple present at the input pin (VIN). To reduce noise and ripple, it is recommended that low equivalent series resistance (ESR) multilayer ceramic chip capacitors (MLCCs) be used for CIN. Tantalum and aluminum capacitors are not recommended because of their high ESR. The input current to the LTC3225/LTC3225-1 is relatively constant during both the input charging phase and the output charging phase but drops to zero during the clock non-overlap times. Since the non-overlap time is small (~40ns) these missing “notches” result in only a small perturbation on the input power supply line. Note that a higher ESR capacitor, such as a tantalum, results in higher input noise. Therefore, ceramic capacitors are recommended for their exceptional ESR performance. Further input noise reduction can be achieved by powering the LTC3225/LTC3225-1 through a very small series inductor as shown in Figure 2. A 10nH inductor will reject the fast current notches, thereby presenting a nearly constant current load to the input power supply. For economy, the 10nH inductor can be fabricated on the PC board with about 1cm (0.4") of PC board trace. Flying Capacitor Selection Warning: Polarized capacitors such as tantalum or aluminum should never be used for the flying capacitor since its voltage can reverse upon start-up of the LTC3225/ LTC3225-1. Low ESR ceramic capacitors should always be used for the flying capacitor. The flying capacitor controls the strength of the charge pump. In order to achieve the rated output current, it is necessary to use at least 0.6μF of capacitance for the flying capacitor. The effective capacitance of a ceramic capacitor varies with temperature and voltage in a manner primarily determined by its formulation. For example, a capacitor made of X5R or X7R material retains most of its capacitance from –40°C to 85°C whereas a Z5U or Y5V type capacitor loses considerable capacitance over that range. X5R, Z5U and Y5V capacitors may also have a poor voltage coefficient causing them to lose 60% or more of their capacitance when the rated voltage is applied. Therefore, when comparing different capacitors, it is often more appropriate to compare the amount of achievable capacitance for a given case size rather than comparing the specified capacitance value. For example, over rated voltage and temperature conditions, a 4.7μF 10V Y5V ceramic capacitor in a 0805 case may not provide any more capacitance than a 1μF 10V X5R or X7R capacitor available in the same 0805 case. In fact, over bias and temperature range, the 1μF 10V X5R or X7R provides more capacitance than the 4.7μF 10V Y5V capacitor. The capacitor manufacturer’s data sheet should be consulted to determine what value of capacitor is needed to ensure minimum capacitance values are met over operating temperature and bias voltage. 10nH 9 VIN 0.1μF 2.2μF 8, 11 VIN LTC3225 LTC3225-1 GND 3225 F02 Figure 2. 10nH Inductor Used for Input Noise Reduction 3225fb 9 LTC3225/LTC3225-1 APPLICATIONS INFORMATION Table 1 contains a list of ceramic capacitor manufacturers and how to contact them. Table 1. Capacitor Manufacturers also be generated if the flying capacitors are far from the part (i.e. the loop area is large). To prevent capacitive energy transfer, a Faraday shield may be used. This is a grounded PC trace between the sensitive node and the LTC3225/LTC3225-1 pins. For a high quality AC ground it should be returned to a solid ground plane that extends all the way to the LTC3225/LTC3225-1. AVX www.avx.com Kemet www.kemet.com Murata www.murata.com Taiyo Yuden www.t-yuden.com Vishay www.vishay.com Table 2. Supercapacitor Manufacturers TDK www.component.tdk.com CAP-XX www.cap-xx.com NESS CAP www.nesscap.com Layout Considerations Maxwell www.maxwell.com Due to the high switching frequency and high transient currents produced by the LTC3225/LTC3225-1, careful board layout is necessary for optimum performance. An unbroken ground plane and short connections to all the external capacitors improves performance and ensures proper regulation under all conditions. Bussmann www.cooperbussmann.com AVX www.avx.com Illinois Capacitor www.illcap.com Tecate Group www.tecategroup.com The voltages on the flying capacitor pins C+ and C– have very fast rise and fall times. The high dV/dt values on these pins can cause energy to capacitively couple to adjacent printed circuit board traces. Magnetic fields can The LTC3225/LTC3225-1 can also be used to charge a single supercapacitor by connecting two series-connected matched ceramic capacitors with a minimum capacitance of 100μF in parallel with the supercapacitor as shown in Figure 3. LTC3225 LTC3225-1 10 COUT CX GND Charging a Single Supercapacitor 3 C1 8, 11 C2 VOUT CSUP 3225 F03 C1 = C2 ≥ 100μF Figure 3. Charging a Single Supercapacitor 3225fb 10 LTC3225/LTC3225-1 TYPICAL APPLICATION 5V Supercapacitor Back-Up Supply Q2 Si4421DY LTM4616 VIN1 VOUT1 VIN 5V VIN2 C6 100μF FB1 R3 4.78k C5 22μF Q1 Si4421DY 1.8V GND ITHM1 1.2V VOUT2 C7 100μF FB2 VIN COUT C+ C1 1μF C4 2.2μF CX LTC3225 LTC3225-1 GND C– R2 10k C2 10F LTC4412 VIN SENSE C3 10F GND GATE CTL C8 100μF 3225 TA02 ITHM2 GND R2 470k STAT SHDN VSEL PROG R1 12k 3225fb 11 LTC3225/LTC3225-1 PACKAGE DESCRIPTION DDB Package 10-Lead Plastic DFN (3mm × 2mm) (Reference LTC DWG # 05-08-1722 Rev Ø) 0.64 p0.05 (2 SIDES) 3.00 p0.10 (2 SIDES) R = 0.05 TYP 0.70 p0.05 2.55 p0.05 1.15 p0.05 PACKAGE OUTLINE 0.25 p 0.05 0.50 BSC 2.39 p0.05 (2 SIDES) PIN 1 BAR TOP MARK (SEE NOTE 6) 0.200 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS R = 0.115 TYP 6 0.40 p 0.10 10 2.00 p0.10 (2 SIDES) 0.75 p0.05 0.64 p 0.05 (2 SIDES) 5 0.25 p 0.05 0 – 0.05 PIN 1 R = 0.20 OR 0.25 s 45o CHAMFER 1 (DDB10) DFN 0905 REV Ø 0.50 BSC 2.39 p0.05 (2 SIDES) BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING CONFORMS TO VERSION (WECD-1) IN JEDEC PACKAGE OUTLINE M0-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3225fb 12 LTC3225/LTC3225-1 REVISION HISTORY (Revision history begins at Rev B) REV DATE DESCRIPTION PAGE NUMBER B 6/10 Updated Note 3 in Electrical Characteristics section. 2, 3 Updates to Pins 8 and 11 in Pin Functions. 5 Update to text in Layout Considerations section. 10 Updated Typical Application and Related Parts. 14 3225fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 13 LTC3225/LTC3225-1 TYPICAL APPLICATION 12V Supercapacitor Back-Up Supply LT3740 HIGH EFFICIENCY DOWN CONVERTER D1 CSHD6-40C DPAK VIN 12V VIN+ + GND C1 47μF 25V DCAP VOUT LT3740 GND VOUT 1.8V 10A GND GND * CHARGER 3 C2 1μF 10V VIN COUT LTC3225/ LTC3225-1 C+ CX C– GND 10A D2 CMSH3-20 VBIAS 3.3V C5 10μF GND 1 M4 Si4410DY D3 CMSH3-20 CHARGER 2 D4 CMSH3-20 VIN COUT LTC3225/ LTC3225-1 C+ CX C3 1μF 10V 8 VM VCC LTC2915 7 2 SEL1 SEL2 6 3 TOL/MR RT 5 4 GND RST R7 10k R1 2k C6 0.1μF R6 1k R2 100k 8 PGND OUT LTC4441-1 7 2 SGND DRVCC 6 3 IN VIN 5 4 EN/SHDN FB C– 1 M3 Si4410DY R3 332k R4 84.5k M2 IRF7424 * GND R5 1k M1 IRF7424 CHARGER 1 C7 10μF C4 1μF 10V VIN COUT LTC3225/ LTC3225-1 C+ CX C– GND 3225 TA03 * REQUIRES PIN 8 (GND) AND EXPOSED PAD TO BE CONNECTED TO A THERMAL PAD ISOLATED FROM THE SYSTEM GROUND. RELATED PARTS PART NUMBER LTC1751-3.3/LTC1751-5 LTC3200 LTC3203/LTC3203B/ LTC3203B-1/LTC3203-1 LTC3204/LTC3204B-3.3/ LTC3204-5 LTC3221/LTC3221-3.3/ LTC3221-5 LTC3240-3.3/LTC3240-2.5 LT®3420/LT3420-1 LT3468/LT3468-1/ LT3468-2 LTC3484-0/LTC3484-1/ LTC3484-2 LT3485-0/LT3485-1/ LT3485-2/LT3485-3 LT3750 LT3751 DESCRIPTION Micropower 5V/3.3V Doubler Charge Pumps Constant Frequency Doubler Charge Pump 500mA Low Noise High Efficiency Dual Mode Step-Up Charge Pumps Low Noise Regulating Charge Pumps COMMENTS IQ = 20μA, Up to 100mA Output, MS-8 Package Low Noise, 5V Output or Adjustable Micropower Regulated Charge Pump Up to 60mA Output Step-Up/Step-Down Regulated Charge Pumps 1.4A/1A Photoflash Capacitor Charger with Automatic Top-Off 1.4A/1A/0.7A, Photoflash Capacitor Charger Up to 150mA Output Charges 220μF to 320V in 3.7 Seconds from 5V, VIN: 2.2V to 16V, ISD < 1μA, 10-Lead MS Package VIN: 2.5V to 16V, Charge Time = 4.6 Seconds for the LT3468 (0V to 320V, 100μF, VIN = 3.6V), ISD < 1μA, ThinSOT™ Package VIN: 1.8V to 16V, Charge Time = 4.6 Seconds for the LT3484-0 (0V to 320V, 100μF, VIN = 3.6V), ISD < 1μA, 2mm × 3mm 6-Lead DFN Package VIN: 1.8V to 10V, Charge Time = 3.7 Seconds for the LT3485-0 (0V to 320V, 100μF, VIN = 3.6V), ISD < 1μA, 3mm × 3mm 10-Lead DFN Driver 1.4A/0.7A/1A, Photoflash Capacitor Charger 1.4A/0.7A/1A/2A Photoflash Capacitor Charger with Output Voltage Monitor and Integrated IGBT Capacitor Charger Controller Capacitor Controller with Regulation VIN: 2.7V to 5.5V, 3mm × 3mm 10-Lead DFN Package Up to 150mA (LTC3204-5), Up to 50mA (LTC3204-3.3) Charges Any Size Capacitor, 10-Lead MS Package Charges Any Size Capacitor, 4mm × 5mm QFN-20 Package 3225fb 14 Linear Technology Corporation LT 0610 REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2008