LTM8055/LTM8055-1
36VIN, 8.5A Buck-Boost
µModule Regulator
FEATURES
DESCRIPTION
Complete Buck-Boost Switch Mode Power Supply
n V
OUT Equal, Greater, Less Than VIN
n Wide Input Voltage Range: 5V to 36V
n 12V/3A Output from 6V
IN
n 12V/6A Output from 12V
IN
n 12V/8.5A Output from 24V
IN
n Up to 97.5% Efficient
n Adjustable Input and Output Average Current Limits
n Input and Output Current Monitors
n Parallelable for Increased Output Current
n Wide Output Voltage Range: 1.2V to 36V
n Selectable Switching Frequency: 100kHz to 800kHz
n Synchronization from 200kHz to 700kHz
n External Compensation (LTM8055-1)
n 15mm × 15mm × 4.92mm BGA Package
The LTM®8055/LTM8055-1 is a 36VIN, buck-boost
µModule® (micromodule) regulator. Included in the package are the switching controller, power switches, inductor
and support components. A resistor to set the switching
frequency, a resistor divider to set the output voltage,
and input and output capacitors are all that are needed
to complete the design. Other features such as input and
output average current regulation may be implemented
with just a few components. The LTM8055/LTM8055-1
operates over an input voltage range of 5V to 36V, and
can regulate output voltages between 1.2V and 36V. The
SYNC input and CLKOUT output allow easy synchronization.
n
APPLICATIONS
Buck-Boost Selection Table
High Power Battery-Operated Devices
Industrial Control
Solar Powered Voltage Regulator
Solar Powered Battery Charging
All registered trademarks and trademarks are the property of their respective owners.
LTM8054
LTM8055/LTM8055-1
LTM8056
VIN (Operation)
36
36
58
VIN Abs Max
40
40
60
VOUT Abs Max
40
40
60
IOUT (Peak)
24VIN, 12VOUT
5.4
8.5
5.5
Package
TYPICAL APPLICATION
VIN
4.7µF
50V
×2
36.5k
RUN
CTL
SS
SYNC
COMP
RT LL MODE
10
VOUT
VOUT
12V
IOUT
GND
96
8
68µF
100k
CLKOUT
IINMON
IOUTMON
FB
98
EFFICIENCY
22µF
25V
OUTPUT
CURRENT
6
94
92
90
4
88
2
11k
8055 TA01a
fSW = 600kHz
EFFICIENCY (%)
SVIN
IIN
LTM8055/
LTM8055-1
15 × 15mm × 4.92mm BGA
Pin and Function Compatible
Maximum Output Current and Efficiency vs VIN
12VOUT from 5VIN to 36VIN Buck-Boost Regulator
VIN
5V TO 36V
15 × 11.25mm ×
3.42mm BGA
OUTPUT CURRENT (A)
n
n
n
n
The LTM8055/LTM8055-1 is housed in a compact overmolded ball grid array (BGA) package suitable for automated assembly by standard surface mount equipment.
The LTM8055/LTM8055-1 is RoHS compliant.
0
86
0
10
20
VIN (V)
30
40
84
8055 TA01b
Rev C
Document Feedback
For more information www.analog.com
1
LTM8055/LTM8055-1
ABSOLUTE MAXIMUM RATINGS
PIN CONFIGURATION
(Note 1)
VIN, SVIN, VOUT, RUN, IIN, IOUT Voltage......................40V
FB, SYNC, CTL, MODE Voltage....................................6V
IINMON, IOUTMON Voltage..............................................6V
LL Voltage..................................................................15V
Maximum Junction Temperature (Notes 2, 3)........ 125°C
Storage Temperature.............................. –55°C to 125°C
Peak Solder Reflow Body Temperature.................. 245°C
TOP VIEW
SVIN
BANK 3
VIN
11
10
BANK 1
GND
IIN
9
8
7
6
5
BANK 2
VOUT
4
RUN
3
IINMON
2
IOUTMON
1
GND
A
B
C
D
IOUT
E
F G H J
K
L
LL
RT FB SS
CLKOUT
MODE SYNC
CTL
COMP
BGA PACKAGE
121-LEAD (15mm × 15mm × 4.92mm)
TJMAX = 125°C, θJA = 20.5°C/W, θJCbottom = 11.0°C/W, θJCtop = 21.2°C/W, θJB = 10.5°C/W,
WEIGHT = 2.8g, θ VALUES DETERMINED PER JEDEC JESD51-9, 51-12
ORDER INFORMATION
PART NUMBER
TERMINAL FINISH
LTM8055EY#PBF
SAC305 (RoHS)
LTM8055IY#PBF
SAC305 (RoHS)
LTM8055IY
SnPb(63/37)
PART MARKING*
DEVICE
FINISH CODE
PACKAGE
TYPE
MSL
RATING
LTM8055Y
e1
BGA
3
–40°C to 125°C
LTM8055Y
e1
BGA
3
–40°C to 125°C
LTM8055Y
e0
BGA
3
–40°C to 125°C
TEMPERATURE RANGE
(SEE NOTE 2)
LTM8055MPY#PBF
SAC305 (RoHS)
LTM8055Y
e1
BGA
3
–55°C to 125°C
LTM8055MPY
SnPb(63/37)
LTM8055Y
e0
BGA
3
–55°C to 125°C
LTM8055EY-1#PBF
SAC305 (RoHS)
LTM8055Y-1
e1
BGA
3
–40°C to 125°C
LTM8055IY-1#PBF
SAC305 (RoHS)
LTM8055Y-1
e1
BGA
3
–40°C to 125°C
• Device temperature grade is indicated by a label on the shipping
container.
• Pad or ball finish code is per IPC/JEDEC J-STD-609.
This product is not recommended for second side reflow.
This product is moisture sensitive. For more information, go to
Recommended BGA PCB Assembly and Manufacturing Procedures.
• BGA Package and Tray Drawings
Rev C
2
For more information www.analog.com
LTM8055/LTM8055-1
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. RUN = 1.5V unless otherwise noted. (Note 2)
PARAMETER
Minimum Input Voltage
Output DC Voltage
Output DC Current
Quiescent Current Into VIN (Tied to SVIN)
Output Voltage Line Regulation
Output Voltage Load Regulation
Output RMS Voltage Ripple
Switching Frequency
CONDITIONS
VIN = SVIN
FB = VOUT Through 100k
RFB = 100k/3.40k
VIN = 6V, VOUT = 12V
VIN = 24V, VOUT = 12V
RUN = 0.3V (Disabled)
No Load, MODE = 0.3V (DCM)
No Load, MODE = 1.5V (FCM)
5V < VIN < 36V, IOUT = 1A
VIN = 12V, 0.1A < IOUT < 6A
VIN = 12V, IOUT = 3A
RT = 453k
RT = 24.9k
MIN
Voltage at FB Pin
l
RUN Falling Threshold
RUN Hysteresis
RUN Low Threshold
RUN Pin Current
IIN Bias Current
Input Current Sense Threshold (IIN-VIN)
IOUT Bias Current
Output Current Sense Threshold (VOUT-IOUT)
LTM8055/LTM8055-1 Stops Switching
LTM8055/LTM8055-1 Starts Switching
LTM8055/LTM8055-1 Disabled
RUN = 1V
RUN = 1.6V
l
1.188
1.176
1.15
1.2
36
3
8.5
0.1
8
45
0.5
0.5
25
100
800
1.2
MAX
5.0
1
30
100
1.212
1.220
1.25
25
2
3
0.3
5
100
90
l
44
56
20
VCTL = Open
l
IINMON Voltage
IOUTMON Voltage
CTL Input Bias Current
SS Pin Current
CLKOUT Output High
CLKOUT Output Low
SYNC Input Low Threshold
SYNC Input High Threshold
SYNC Bias Current
MODE Input Low Threshold
MODE Input High Threshold
TYP
l
LTM8055/LTM8055-1 in Input Current Limit
LTM8055/LTM8055-1 in Output Current Limit
VCTL = 0V
VSS = 0V
10k to GND
10k to 5V
54.5
53
0.96
1.14
61.5
63
1.04
1.26
22
35
4
0.7
0.3
1.5
SYNC = 1V
11
0.3
1.5
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTM8055E/LTM8055E-1 is guaranteed to meet performance
specifications from 0°C to 125°C internal. Specifications over the full
–40°C to 125°C internal operating temperature range are assured by
design, characterization and correlation with statistical process controls.
The LTM8055I/LTM8055I-1 is guaranteed to meet specifications over
the full –40°C to 125°C internal operating temperature range. The
LTM8055MP/LTM8055MP-1 is guaranteed to meet specifications over
UNITS
V
V
V
A
A
µA
mA
mA
%
%
mV
kHz
kHz
V
V
V
mV
V
µA
nA
µA
mV
µA
mV
mV
V
V
µA
µA
V
V
V
V
µA
V
V
the full –55°C to 125°C internal operating temperature range. Note that
the maximum internal temperature is determined by specific operating
conditions in conjunction with board layout, the rated package thermal
resistance and other environmental factors.
Note 3: The LTM8055/LTM8055-1 contains overtemperature protection
that is intended to protect the device during momentary overload
conditions. The internal temperature exceeds the maximum operating
junction temperature when the overtemperature protection is active.
Continuous operation above the specified maximum operating junction
temperature may impair device reliability.
Rev C
For more information www.analog.com
3
LTM8055/LTM8055-1
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency vs Output Current
(3.3VOUT)
100
40
0
2
4
6
8
OUTPUT CURRENT (A)
60
40
5VIN
12VIN
24VIN
36VIN
20
20
10
0
2
4
6
8
OUTPUT CURRENT (A)
100
40
Efficiency vs Output Current
(18VOUT)
3
6
OUTPUT CURRENT (A)
100
EFFICIENCY (%)
60
20
9
0
2
4
6
OUTPUT CURRENT (A)
60
5VIN
12VIN
24VIN
36VIN
50
40
0
1
2
3
4
OUTPUT CURRENT (A)
0
1
2
3
4
5
OUTPUT CURRENT (A)
5
10
7
5VIN
12VIN
24VIN
36VIN
8
4
3
2
0
6
Input Current vs Output Current
(5VOUT)
6
4
2
1
5
5VIN
12VIN
24VIN
36VIN
8055 G06
INPUT CURRENT (A)
INPUT CURRENT (A)
EFFICIENCY (%)
70
20
8
5VIN
12VIN
24VIN
36VIN
6
80
60
Input Current vs Output Current
(3.3VOUT)
7
90
10
Efficiency vs Output Current
(24VOUT)
8055 G05
Efficiency vs Output Current
(36VOUT)
4
6
8
OUTPUT CURRENT (A)
40
5VIN
12VIN
24VIN
36VIN
8055 G04
100
2
80
40
5VIN
12VIN
24VIN
36VIN
0
0
8055 G03
80
EFFICIENCY (%)
EFFICIENCY (%)
80
20
20
10
5VIN
12VIN
24VIN
36VIN
8055 G02
100
60
60
40
5VIN
12VIN
24VIN
36VIN
8055 G01
Efficiency vs Output Current
(12VOUT)
Efficiency vs Output Current
(8VOUT)
80
EFFICIENCY (%)
EFFICIENCY (%)
EFFICIENCY (%)
100
80
60
0
Efficiency vs Output Current
(5VOUT)
100
80
TA = 25°C, unless otherwise noted.
0
2
4
6
8
OUTPUT CURRENT (A)
8055 G07
10
8055 G08
0
0
2
4
6
8
OUTPUT CURRENT (A)
10
8055 G09
Rev C
4
For more information www.analog.com
LTM8055/LTM8055-1
TYPICAL PERFORMANCE CHARACTERISTICS
10
6
4
6
4
2
4
6
8
OUTPUT CURRENT (A)
0
10
0
3
6
OUTPUT CURRENT (A)
Input Current vs Output Current
(24VOUT)
4
6
5
4
3
5VIN
12VIN
24VIN
36VIN
1
2
4
OUTPUT CURRENT (A)
0
6
0
1
2
3
4
OUTPUT CURRENT (A)
8055 G13
10
100
8
80
6
4
12VOUT
18VOUT
24VOUT
36VOUT
2
0
0
10
20
VIN (V)
30
40
8055 G16
8
6
4
5
3.3VOUT
5VOUT
8VOUT
0
10
20
VIN (V)
8055 G14
TEMPERATURE RISE (°C)
OUTPUT CURRENT (A)
Maximum Output Current vs VIN
Maximum Output Current vs VIN
10
2
0
8
8055 G12
7
2
0
2
4
6
OUTPUT CURRENT (A)
8
INPUT CURRENT (A)
INPUT CURRENT (A)
6
0
Input Current vs Output Current
(36VOUT)
9
5VIN
12VIN
24VIN
36VIN
8
5VIN
12VIN
24VIN
36VIN
8055 G11
8055 G10
10
4
0
9
OUTPUT CURRENT (A)
0
6
2
Temperature Rise vs Output
Current (3.3VOUT)
100
5VIN
12VIN
24VIN
36VIN
60
40
20
0
0
2
30
40
8055 G15
Temperature Rise vs Output
Current (5VOUT)
TEMPERATURE RISE (°C)
0
8
2
2
Input Current vs Output Current
(18VOUT)
10
5VIN
12VIN
24VIN
36VIN
8
INPUT CURRENT (A)
INPUT CURRENT (A)
10
5VIN
12VIN
24VIN
36VIN
8
Input Current vs Output Current
(12VOUT)
INPUT CURRENT (A)
Input Current vs Output Current
(8VOUT)
TA = 25°C, unless otherwise noted.
4
6
8
OUTPUT CURRENT (A)
10
8055 G17
5VIN
12VIN
24VIN
36VIN
80
60
40
20
0
0
2
4
6
8
OUTPUT CURRENT (A)
10
8055 G18
Rev C
For more information www.analog.com
5
LTM8055/LTM8055-1
TYPICAL PERFORMANCE CHARACTERISTICS
Temperature Rise vs Output
Current (8VOUT)
TA = 25°C, unless otherwise noted.
Temperature Rise vs Output
Current (12VOUT)
Temperature Rise vs Output
Current (18VOUT)
80
80
80
60
40
5VIN
12VIN
24VIN
36VIN
20
0
0
2
4
6
8
OUTPUT CURRENT (A)
60
40
5VIN
12VIN
24VIN
36VIN
20
0
10
0
2
4
6
OUTPUT CURRENT (A)
8055 G19
40
0
8
40
5VIN
12VIN
24VIN
36VIN
20
0
2
4
OUTPUT CURRENT (A)
TEMPERATURE RISE (°C)
60
0
2
4
6
OUTPUT CURRENT (A)
6
Output Voltage Ripple, Unmodified
DC2017A Demo Board 12VOUT
24VIN
6A LOAD
(BUCK)
100mV/DIV
80
MEASURED WITH HP461N
150MHz AMPLIFIER
12VIN
6A LOAD
(BUCK-BOOST)
100mV/DIV
60
40
6VIN
3A LOAD
(BOOST)
100mV/DIV
5VIN
12VIN
24VIN
36VIN
20
0
8
8055 G21
100
80
5VIN
12VIN
24VIN
36VIN
20
Temperature Rise vs Output
Current (36VOUT)
100
TEMPERATURE RISE (°C)
60
8055 G20
Temperature Rise vs Output
Current (24VOUT)
0
TEMPERATURE RISE (°C)
100
TEMPERATURE RISE (°C)
100
TEMPERATURE RISE (°C)
100
0
8055 G22
1
2
3
4
OUTPUT CURRENT (A)
0.5µs/DIV
5
8055 G24
8055 G23
Maximum Output Current vs
CTL Voltage, Unmodified
DC2017A, 12VIN
Start-Up Behavior, DC2017A,
24VIN, 3A Resistive Load
8
NO CSS
OUTPUT CURRENT (A)
2V/DIV
7
CSS = 0.022µF
CSS = 0.22µF
6
5
4
3
2
1
500µs/DIV
8055 G25
0
0
0.2
0.4 0.6 0.8
1
CTL VOLTAGE (V)
1.2
1.4
8055 G26
Rev C
6
For more information www.analog.com
LTM8055/LTM8055-1
PIN FUNCTIONS
GND (Bank 1, Pin L1): Tie these GND pins to a local
ground plane below the LTM8055/LTM8055-1 and the
circuit components. In most applications, the bulk of the
heat flow out of the LTM8055/LTM8055-1 is through these
pads, so the printed circuit design has a large impact on
the thermal performance of the part. See the PCB Layout
and Thermal Considerations sections for more details.
Return the RFB1/RFB2 feedback divider to this net.
MODE (Pin G2): Switching Mode Input. The LTM8055/
LTM8055-1 operates in forced continuous mode when
MODE is open, and can operate in discontinuous switching mode when MODE is low. In discontinuous switching
mode, the LTM8055/LTM8055-1 will block reverse inductor current. This pin is normally left open or tied to LL.
This pin may be tied to GND for the purpose of blocking
reverse current if no output current sense resistor is used.
VOUT (Bank 2): Power Output Pins. Apply output filter
capacitors between these pins and GND pins.
RT (Pin H1): Timing Resistor. The RT pin is used to program
the switching frequency of the LTM8055/LTM8055-1 by
connecting a resistor from this pin to ground. The range
of oscillation is 100kHz to 800kHz. The Applications
Information section of the data sheet includes a table
to determine the resistance value based on the desired
switching frequency. Minimize capacitance at this pin.
VIN (Bank 3): Input Power. The VIN pin supplies current to
the LTM8055/LTM8055-1’s internal power switches and
to one terminal of the optional input current sense resistor. This pin must be locally bypassed with an external,
low ESR capacitor; see Table 1 for recommended values.
IOUT (Pin D1): Output Current Sense. Tie this pin to the
output current sense resistor. The output average current
sense threshold is 58mV, so the LTM8055/LTM8055-1
will regulate the output current to 58mV/RSENSE, where
RSENSE is the value of the output current sense resistor
in ohms. The load is powered through the sense resistor
connected at this pin. Tie this pin to VOUT if no output
current sense resistor is used. Keep this pin within ±0.5V
of VOUT under all conditions.
LL (Pin F1): Light Load Indicator. This open drain pin
indicates that the output current, as sensed through the
resistor connected between VOUT and IOUT, is approximately
equivalent to 6mV or less. Its state is meaningful only if a
current sense resistor is applied between VOUT and IOUT.
This is useful to change the switching behavior of the
LTM8055/LTM8055-1 in light load conditions.
SVIN (Pins F10, F11): Controller Power Input. Apply a
separate voltage above 5V if the LTM8055/LTM8055-1
is required to operate when the main power input (VIN)
is below 5V. Bypass these pins with a high quality, low
ESR capacitor. If a separate supply is not used, connect
these pins to VIN.
CLKOUT (Pin G1): Clock Output. Use this pin as a clock
source when synchronizing other devices to the switching
frequency of the LTM8055/LTM8055-1. When this function
is not used, leave this pin open.
SYNC (Pin H2): External Synchronization Input. The SYNC
pin has an internal pull-down resistor. See the Synchronization section in Applications Information for details. Tie
this pin to GND when not used.
FB (Pin J1): Output Voltage Feedback. The LTM8055/
LTM8055-1 regulates the FB pin to 1.2V. Connect the FB
pin to a resistive divider between the output and GND to
set the output voltage. See Table 1 for recommended FB
divider resistor values.
COMP (Pin J2): Compensation Pin. The LTM8055 is
equipped with internal compensation that works well with
most applications, so this pin is usually left open. Some
applications, however, may benefit from a compensation
network other than the one integrated into the LTM8055.
In such cases, use the LTM8055-1, which has no internal
compensation network and apply an appropriate external
compensation network for optimal and proper operation.
SS (Pin K1): Soft-Start. Connect a capacitor from this pin
to GND to increase the soft-start time. Soft-start reduces
the input power source’s surge current by gradually increasing the controller’s current limit. Larger values of the
soft-start capacitor result in longer soft-start times. If no
soft-start is required, leave this pin open.
CTL (Pin K2): Current Sense Adjustment. Apply a voltage
below 1.2V to reduce the current limit threshold of IOUT.
Drive CTL to less than 50mV to stop switching. The CTL
pin has an internal pull-up resistor to 2V. If not used,
leave open.
Rev C
For more information www.analog.com
7
LTM8055/LTM8055-1
PIN FUNCTIONS
IOUTMON (Pin L2): Output Current Monitor. This pin produces a voltage that is proportional to the voltage between
VOUT and IOUT. IOUTMON will equal 1.2V when VOUT – IOUT
= 58mV. This feature is generally useful only if a current
sense resistor is applied between VOUT and IOUT. This is
a high impedance output. Use a buffer to drive a load.
(typical), but below 6V, the RUN pin input bias current is
less than 1μA. Below 1.2V and above 0.3V, the RUN pin
sinks 3μA so the user can define the hysteresis with the
external resistor selection. This will also reset the soft-start
function. If RUN is 0.3V or less, the LTM8055/LTM8055-1
is disabled and the SVIN quiescent current is below 1μA.
IINMON (Pin L3): Input Current Monitor. This pin produces
a voltage that is proportional to the voltage between IIN
and VIN. IINMON will equal 1V when IIN – VIN = 50mV. This
feature is generally useful only if a current sense resistor
is applied between VIN and IIN.
IIN (Pin L9): Input Current Sense. Tie this pin to the input
current sense resistor. The input average current sense
threshold is 50mV, so the LTM8055/LTM8055-1 will
regulate the input current to 50mV/RSENSE, where RSENSE
is the value of the input current sense resistor in ohms.
Tie to VIN when not used. Keep this pin within ±0.5V of
VIN under all conditions.
RUN (Pin L4): LTM8055/LTM8055-1 Enable. Raise the RUN
pin voltage above 1.2V for normal operation. Above 1.2V
BLOCK DIAGRAM
VIN
VOUT
SVIN
IOUT
4.7µH
IIN
0.47µF
50V
0.2µF
RUN
GND
2V
SS
100k
FB
100k
CLKOUT
BUCK-BOOST CONTROLLER
0.1µF
IINMON
IOUTMON
CTL
MODE
COMP
LL
RT
SYNC
8055 BD
Rev C
8
For more information www.analog.com
LTM8055/LTM8055-1
OPERATION
The LTM8055/LTM8055-1 is a standalone nonisolated
buck-boost switching DC/DC power supply. The buck-boost
topology allows the LTM8055/LTM8055-1 to regulate its
output voltage for input voltages both above and below
the magnitude of the output. The maximum output current
depends upon the input voltage. Higher input voltages
yield higher maximum output current.
This converter provides a precisely regulated output voltage programmable via an external resistor divider from
1.2V to 36V. The input voltage range is 5V to 36V, but
the LTM8055/LTM8055-1 may be operated at lower input
voltages if SVIN is powered by a voltage source above 5V.
A simplified block diagram is given on the previous page.
The LTM8055/LTM8055-1 contains a current mode controller, power switching elements, power inductor and
a modest amount of input and output capacitance. The
LTM8055/LTM8055-1 is a fixed frequency PWM regulator.
The switching frequency is set by connecting the appropriate resistor value from the RT pin to GND.
The output voltage of the LTM8055/LTM8055-1 is set by
connecting the FB pin to a resistor divider between VOUT
and GND.
In addition to regulating its output voltage, the LTM8055/
LTM8055-1 is equipped with average current control loops
for both the input and output. Add a current sense resistor
between IIN and VIN to limit the input current below some
maximum value. The IINMON pin reflects the current flowing
though the sense resistor between IIN and VIN.
A current sense resistor between VOUT and IOUT allows
the LTM8055/LTM8055-1 to accurately regulate its output
current to a maximum value set by the value of the sense
resistor. When the resistor is present, the IOUTMON pin
reflects the output current flowing through VOUT.
In general, the LTM8055/LTM8055-1 should be used with an
output sense resistor to limit the maximum output current,
as buck-boost regulators are capable of delivering large
currents when the output voltage is lower than the input,
if demanded.
Furthermore, while the LTM8055/LTM8055-1 does not
require an output sense resistor to operate, it uses information from the sense resistor to optimize its performance.
If an out-put sense resistor is not used, the efficiency
or output ripple may degrade, especially if the current
through the integrated inductor is discontinuous. In some
cases, an output sense resistor is required to adequately
protect the LTM8055/LTM8055-1 against output overload
or short-circuit.
A voltage less than 1.2V applied to the CTL pin reduces
the maximum output current. Drive CTL to about 50mV
to stop switching. The current flowing through the sense
resistor is reflected by the output voltage of the IOUTMON pin.
Driving the SYNC pin will synchronize the LTM8055/
LTM8055-1 to an external clock source. The CLKOUT
pin sources a signal that is the same frequency but approximately 180° out of phase with the internal oscillator.
If more output current is required than a single LTM8055/
LTM8055-1 can provide, multiple devices may be operated in parallel. Refer to the Parallel Operation section of
Applications Information for more details.
An internal regulator provides power to the control circuitry
and the gate driver to the power MOSFETs. This internal
regulator draws power from the SVIN pin. The RUN pin
is used to place the LTM8055/LTM8055-1 in shutdown,
disconnecting the output and reducing the input current
to less than 1μA.
The LTM8055/LTM8055-1 is equipped with a thermal
shutdown that inhibits power switching at high junction
temperatures. The activation threshold of this function is
above 125°C to avoid interfering with normal operation,
so prolonged or repetitive operation under a condition in
which the thermal shutdown activates may damage or
impair the reliability of the device.
The LTM8055 features an integrated compensation network
that works well under most conditions. Some applications,
however, benefit from a different compensation network.
In such cases, use the LTM8055-1, which has no internal
compensation network. Apply an appropriate external
compensation network for optimal and proper operation.
Rev C
For more information www.analog.com
9
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
For most applications, the design process is straight forward, summarized as follows:
the graphs in the Typical Performance Characteristics
section for guidance.
1. Look at Table 1 and find the row that has the desired
input range and output voltage.
The maximum frequency (and attendant RT value) at which
the LTM8055/LTM8055-1 should be allowed to switch is
given in Table 1 in the fMAX column, while the recommended
frequency (and RT value) for optimal efficiency over the
given input condition is given in the fOPTIMAL column.
There are additional conditions that must be satisfied if
the synchronization function is used. Please refer to the
Synchronization section for details.
2. Apply the recommended CIN, COUT, RFB1/RFB2 and RT
values.
3. Apply the output sense resistor to set the output current
limit. The output current is limited to 58mV/RSENSE,
where RSENSE is the value of the output current sense
resistor in ohms.
4. When using the LTM8055-1, place the external compensation network as close as possible to the COMP pin.
While these component combinations have been tested
for proper operation, it is incumbent upon the user to
verify proper operation over the intended system’s line,
load and environmental conditions. Bear in mind that
the maximum output current is limited by junction temperature, the relationship between the input and output
voltage magnitude and other factors. Please refer to
Note that Table 1 calls out both ceramic and electrolytic
output capacitors. Both of the capacitors called out in
the table must be applied to the output. The electrolytic
capacitors in Table 1 are described by voltage rating,
value and ESR. The voltage rating of the capacitor may
be increased if the application requires a higher voltage
stress derating. The LTM8055/LTM8055-1 can tolerate
variation in the ESR; other capacitors with different ESR
may be used, but the user must verify proper operation
over line, load and environmental conditions. Table 2
Table 1. Recommended Component Values and Configuration (TA = 25°C)
VIN RANGE
5V to 24V
VOUT
CIN
COUT
RFB1/RFB2 fOPTIMAL (kHz) RT(OPTIMAL) fMAX (kHz) RT(MAX)
3.3V 2 × 4.7µF, 50V, X5R, 0805 22µF, 6.3V, X5R, 0805
100k/56.2k
600
36.5k
800
24.9k
100µF, 6V, 75mΩ, Electrolytic
5V to 28V
5V 2 × 4.7µF, 50V, X5R, 0805 22µF, 6.3V, X5R, 0805
100k/31.6k
550
39.2k
800
24.9k
100µF, 6V, 75mΩ, Electrolytic
5V to 31V
8V 2 × 4.7µF, 50V, X5R, 0805 47µF, 10V, X5R, 1206
100k/17.4k
500
45.3k
800
24.9k
100µF, 16V, 100mΩ, Electrolytic
5V to 36V
12V 2 × 4.7µF, 50V, X5R, 1210 22µF, 25V, X5R, 0805
100k/11k
600
36.5k
800
24.9k
68µF, 16V, 200mΩ, Electrolytic
5V to 36V
18V 2 × 4.7µF, 50V, X7R, 1210 2 x 22µF, 25V, X5R, 1210
100k/6.98k
500
45.3k
800
24.9k
47µF, 25V, 900mΩ, Electrolytic
5V to 36V
24V 2 × 4.7µF, 50V, X7R, 1210 22µF, 25V, X5R, 1210
100k/5.23k
650
31.6k
800
24.9k
33µF, 35V 300mΩ, Electrolytic
5.5V to 36V 36V 2 × 4.7µF, 50V, X7R, 1210 10µF, 50V, X5R, 1206
100k/3.40k
650
31.6k
800
24.9k
10µF, 50V 120mΩ, Electrolytic
Notes: An input bulk capacitor is required. The output capacitance uses a combination of a ceramic and electrolytic in parallel. Other combinations of
resistor values for the RFB network are acceptable.
Table 2. Electrolytic Caps Used in LTM8055/LTM8055-1 Testing
DESCRIPTION
100µF, 6V, 75mΩ, Tantalum C Case
100µF, 16V, 100mΩ, Tantalum Y Case
68µF, 16V, 200mΩ, Tantalum C Case
47µF, 25V, 900mΩ, Tantalum D Case
33µF, 35V, 300mΩ, Tantalum D Case
10µF, 50V, 120mΩ, Aluminum 6.3 × 6mm case
MANUFACTURER
AVX
AVX
AVX
AVX
AVX
Suncon
PART NUMBER
TPSC107M006R0075
TPSY107M016R0100
TPSC686M016R0200
TAJD476M025R
TPSD336M035R0300
50HVP10M
Rev C
10
For more information www.analog.com
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
gives the description and part numbers of electrolytic
capacitors used in the LTM8055/LTM8055-1 development
testing and design validation.
Table 3. Switching Frequency vs RT Value
FREQUENCY
RT VALUE (kΩ)
100
453
200
147
300
84.5
Capacitor Selection Considerations
The CIN and COUT capacitor values in Table 1 are the
minimum recommended values for the associated operating conditions. Applying capacitor values below those
indicated in Table 1 is not recommended, and may result
in undesirable operation. Using larger values is generally
acceptable, and can yield improved dynamic response, if
it is necessary. Again, it is incumbent upon the user to
verify proper operation over the intended system’s line,
load and environmental conditions.
Ceramic capacitors are small, robust and have very low
ESR. However, not all ceramic capacitors are suitable.
X5R and X7R types are stable over temperature and applied voltage and give dependable service. Other types,
including Y5V and Z5U have very large temperature and
voltage coefficients of capacitance. In an application circuit they may have only a small fraction of their nominal
capacitance resulting in much higher output voltage ripple
than expected.
A final precaution regarding ceramic capacitors concerns
the maximum input voltage rating of the LTM8055/
LTM8055-1. A ceramic input capacitor combined with
trace or cable inductance forms a high Q (underdamped)
tank circuit. If the LTM8055/LTM8055-1 circuit is plugged
into a live supply, the input voltage can ring to twice its
nominal value, possibly exceeding the device’s rating.
This situation is easily avoided; see the Hot-Plugging
Safely section.
Frequency Selection
The LTM8055/LTM8055-1 uses a constant frequency
PWM architecture that can be programmed to switch from
100kHz to 800kHz by tying a resistor from the RT pin to
ground. Table 3 provides a list of RT resistor values and
their re-sultant frequencies.
400
59
500
45.3
600
36.5
700
29.4
800
24.9
An external resistor from RT to GND is required. Do not
leave this pin open, even when synchronizing to an external clock. When synchronizing the switching of the
LTM8055/LTM8055-1 to an external signal source, the
frequency range is 200kHz to 700kHz.
Operating Frequency Trade-Offs
It is recommended that the user apply the optimal RT
value given in Table 1 for the input and output operating
condition. System level or other considerations, however,
may necessitate another operating frequency. While the
LTM8055/LTM8055-1 is flexible enough to accommodate
a wide range of operating frequencies, a haphazardly
chosen one may result in undesirable operation under
certain operating or fault conditions. A frequency that is
too high can reduce efficiency, generate excessive heat
or even damage the LTM8055/LTM8055-1 if the output
is overloaded or short circuited. A frequency that is too
low can result in a final design that has too much output
ripple, too large of an output capacitor or is unstable.
Parallel Operation
Two or more LTM8055/LTM8055-1s may be combined to
provide increased output current by configuring them as a
master and a slave, as shown in Figure 1. Each LTM8055/
LTM8055-1 is equipped with an IOUTMON and a CTL pin.
The IOUTMON pin’s 0 to 1.2V signal reflects the current
passing through the output sense resistor, while a voltage
less than 1.2V applied to the CTL pin will limit the current
passing through the output sense resistor. By applying
the voltage of the master’s IOUTMON pin to the slave’s CTL
Rev C
For more information www.analog.com
11
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
pin, the two units will source the same current to the load,
assuming each LTM8055/LTM8055-1 output current sense
resistor is the same value.
MASTER
OUTPUT CURRENT
SENSE RESISTOR
TO LOAD
VOUT
IOUT
IOUTMON
UNITY GAIN
BUFFER
CTL
SLAVE
VOUT
Paralleled LTM8055/LTM8055-1s should normally be allowed to switch in discontinuous mode to prevent current
from flowing from the output of one unit into another; that
is, the MODE pin should be tied to LL. In some cases,
operating the master in forced continuous (MODE open)
and the slaves in discontinuous mode (MODE = LL) is
desirable. If so, current from the output can flow into the
master’s input. Please refer to Input Precaution in this
section for a discussion of this behavior.
Minimum Input Voltage and RUN
OUTPUT CURRENT
SENSE RESISTOR
IOUT
8055 F01
Figure 1. Two or More LTM8055/LTM8055-1s May Be Connected
in a Master/Slave Configuration for Increased Output Current
The design of a master-slave configuration is straight
forward:
1. Apply the FB resistor network to the master, choosing
the proper values for the desired output voltage. Suggested values for popular output voltages are provided
in Table 1.
2. Apply a FB resistor network to the individual slaves
so that the resulting output is higher than the desired
output voltage.
3. Apply the appropriate output current sense resistors
between VOUT and IOUT. If the same value is used for the
master and slave units, they will share current equally.
The LTM8055/LTM8055-1 needs a minimum of 5V for
proper operation, but system parameters may dictate that
the device operate only above some higher input voltage.
For ex-ample, a LTM8055/LTM8055-1 may be used to
produce 12VOUT, but the input power source may not be
budgeted to provide enough current if the input supply
voltage is below 8V.
The RUN pin has a typical falling voltage threshold of
1.2V and a typical hysteresis of 25mV. In addition, the
pin sinks 3µA below the RUN threshold. Based upon the
above information and the circuit shown in Figure 2, the
VIN rising (turn-on) threshold is:
VIN = ( 3µA • R1) + 1.225V
R2
and the VIN falling turn-off threshold is:
VIN = 1.2
R1+R2
R2
LTM8055/
LTM8055-1
4. Connect the master IOUTMON to the slaves’ CTL pin
through a unity gain buffer. The unity gain buffer is required to isolate the output impedance of the LTM8055/
LTM8055-1 from the integrated pull-up on the CTL pins.
VIN
R1
RUN
R2
8055 F02
5. Tie the outputs together.
Note that this configuration does not require the inputs to
be tied together, making it simple to power a single heavy
load from multiple input sources. Ensure that each input
power source has sufficient voltage and current sourcing
capability to provide the necessary power. Please refer
to the Maximum Output Current vs VIN and Input Current
vs Output Current curves in the Typical Performance
Characteristics section for guidance.
12
R1+R2
Figure 2. This Simple Resistor Network Sets the Minimum
Operating Input Voltage Threshold with Hysteresis
Minimum Input Voltage and SVIN
The minimum input voltage of the LTM8055/LTM8055-1
is 5V, but this is only if VIN and SVIN are tied to the same
voltage source. If SVIN is powered from a power source
at or above 5VDC, VIN can be allowed to fall below 5V and
For more information www.analog.com
Rev C
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
the LTM8055/LTM8055-1 can still operate properly. Some
examples of this are provided in the Typical Applications
section.
Soft-Start
Soft-start reduces the input power sources’ surge currents by gradually increasing the controller’s current. As
indicated in the Block Diagram, the LTM8055/LTM8055-1
has an internal soft-start RC network. Depending upon the
load and operating conditions, the internal network may
be sufficient for the application. To increase the soft-start
time, simply add a capacitor from SS to GND.
Output Current Limit (IOUT)
The LTM8055/LTM8055-1 features an accurate average
output current limit set by an external sense resistor placed
between VOUT and IOUT as shown in Figure 3. VOUT and
IOUT internally connect to a differential amplifier that limits
the current when the voltage VOUT-IOUT reaches 58mV.
The current limit is:
IOUT(LIM) =
58mV
R SENSE
where RSENSE is the value of the sense resistor in ohms.
Most applications should use an output sense resistor as
shown in Figure 3, if practical. The internal buck-boost
power stage is current limited, but is nonetheless capable
of delivering large amounts of current in an overload
condition, especially when the output voltage is much
lower than the input and the power stage is operating as
a buck converter.
LTM8055/
LTM8055-1
VOUT
IOUT
tying the LL and MODE pins together can improve performance—see Switching Mode in this section.
In high step-down voltage regulator applications, the
internal current limit can be quite high to allow proper
operation. This can potentially damage the LTM8055/
LTM8055-1 in overload or short-circuit conditions. Apply an output current sense resistor to set an appropriate
current limit to protect the LTM8055/LTM8055-1 against
these fault conditions.
Output Current Limit Control (CTL)
Use the CTL input to reduce the output current limit from
the value set by the external sense resistor applied between
VOUT and IOUT. The typical control range is between 0V
and 1.2V. The CTL pin does not directly affect the input
current limit. If this function is not used, leave CTL open.
Drive CTL to less than about 50mV to stop switching. The
CTL pin has an internal pull-up resistor to 2V.
Input Current Limit (IIN)
Some applications require that LTM8055/LTM8055-1 draw
no more than some predetermined current from the power
source. Current limited power sources and power sharing
are two examples. The LTM8055/LTM8055-1 features
an accurate input current limit set by an external sense
resistor placed between IIN and VIN as shown in Figure
4. VIN and IIN internally connect to a differential amplifier
that limits the current when the voltage IIN-VIN reaches
50mV. The current limit is:
IIN(LIM) =
50mV
R SENSE
where RSENSE is the value of the sense resistor in ohms.
RSENSE
If input current limiting is not required, simply tie IIN to VIN.
LOAD
8055 F03
Figure 3. Set The LTM8055/LTM8055-1 Output Current Limit with
an External Sense Resistor
When the voltage across the output sense resistor falls
to about 1/10th of full scale, the LL pin pulls low. If there
is no output sense resistor, and IOUT is tied to VOUT, LL
will be active low. Applying an output sense resistor and
POWER
SOURCE
LTM8055/
RSENSE LTM8055-1
VIN
IIN
8055 F04
Figure 4. Set the LTM8055/LTM8055-1 Input Current
Limit with an External Sense Resistor
For more information www.analog.com
Rev C
13
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
Input Current Monitor (IINMON)
The IINMON pin produces a voltage equal to approximately
20 times the voltage of IIN – VIN. Since the LTM8055/
LTM8055-1 input current limit engages when IIN – VIN =
50mV, IINMON will be 1V at maximum input current.
Output Current Monitor (IOUTMON)
The IOUTMON pin produces a voltage proportional to the
voltage of VOUT – IOUT. Since the LTM8055/LTM8055-1
output current limit engages when VOUT – IOUT = 58mV,
IOUTMON will be 1.2V at maximum output current.
Synchronization
The LTM8055/LTM8055-1 switching frequency can be
synchronized to an external clock using the SYNC pin.
Driving SYNC with a 50% duty cycle waveform is a good
choice, otherwise maintain the duty cycle between about
10% and 90%. When synchronizing, a valid resistor value
(that is, a value that results in a free-running frequency of
100kHz to 800kHz) must be connected from RT to GND.
While an RT resistor is required for proper operation, the
value of this resistor is independent of the frequency of
the externally applied SYNC signal. Be aware, however,
that the LTM8055/LTM8055-1 will switch at the frequency
prescribed by the RT value if the SYNC signal terminates,
so choose an appropriate resistor value.
CLKOUT
The CLKOUT signal reflects the internal switching clock
of the LTM8055/LTM8055-1. It is phase shifted by approximately 180° with respect to the leading edge of the
internal clock. If CLKOUT is connected to the SYNC input
of another LTM8055/LTM8055-1, the two devices will
switch about 180° out of phase.
Input Precaution
In applications where the output voltage is deliberately
pulled up above the set regulation voltage or the FB pin is
abruptly driven to a new voltage, the LTM8055/LTM8055-1
may attempt to regulate the voltage by removing energy
from the load for a short period of time after the output
is pulled up. Since the LTM8055/LTM8055-1 is a syn-
chronous switching converter, it delivers this energy to
the input. If there is nothing on the LTM8055/LTM8055-1
input to consume this energy, the input voltage may rise.
If the input voltage rises without intervention, it may rise
above the absolute maximum rating, damaging the part.
Carefully examine the input voltage behavior to see if the
application causes it to rise.
In many cases, the system load on the LTM8055/LTM80551 input bus will be sufficient to absorb the energy delivered
by the μModule regulator. The power required by other
devices will consume more than enough to make up for
what the LTM8055/LTM8055-1 delivers. In cases where
the LTM8055/LTM8055-1 is the largest or only power
converter, this may not be true and some means may need
to be devised to prevent the LTM8055/LTM8055-1’s input
from rising too high. Figure 5a shows a passive crowbar
circuit that will dissipate energy during momentary input
overvoltage conditions. The break-down voltage of the
Zener diode is chosen in conjunction with the resistor R to
set the circuit’s trip point. The trip point is typically set well
above the maximum VIN voltage under normal operating
conditions. This circuit does not have a precision threshold, and is subject to both part-to-part and temperature
variations, so it is most suitable for applications where
the maximum input voltage is much less than the 40VIN
absolute maximum. As stated earlier, this type of circuit
is best suited for momentary overvoltages.
Figure 5a is a crowbar circuit, which attempts to prevent
the input voltage from rising above some level by dumping
energy to GND through a power device. In some cases,
it is possible to simply turn off the LTM8055/LTM8055-1
when the input voltage exceeds some threshold. An example of this circuit is shown in Figure 5b. When the power
source on the output drives VIN above a predetermined
threshold, the comparator pulls down on the RUN pin
and stops switching in the LTM8055/LTM8055-1. When
this happens, the input capacitance needs to absorb the
energy stored within the LTM8055/LTM8055-1’s internal
inductor, resulting in an additional voltage rise. This voltage rise depends upon the input capacitor size and how
much current is flowing from the LTM8055/LTM8055-1
output to input.
Rev C
14
For more information www.analog.com
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
LOAD
CURRENT
VIN
ZENER
DIODE
Q
VOUT
LTM8055/
LTM8055-1
GND
SOURCING
LOAD
R
8055 F05a
Figure 5a. The MOSFET Q Dissipates Momentary Energy to
GND. The Zener Diode and Resistor Are Chosen to Ensure That
the MOSFET Turns On Above the Maximum VIN Voltage Under
Normal Operation
LOAD
CURRENT
VIN
VOUT
LTM8055/
LTM8055-1
GND
RUN
10µF
–
+
SOURCING
LOAD
EXTERNAL
REFERENCE
VOLTAGE
from buck, buck-boost or boost operating modes, especially at lighter loads. In such a case, it can be desirable
to operate in forced continuous mode except when the
internal inductor current is about to reverse. If so, apply
a current sense resistor between VOUT and IOUT and tie
the LL and MODE pins together. The LL pin is low when
the current through the output sense resistor is about
one-tenth the full-scale maximum. When the output current falls to this level, the LL pin will pull the MODE pin
down, putting the LTM8055/LTM8055-1 in discontinuous
mode, preventing reverse current from flowing from the
output to the input. In the case where MODE and LL are
tied together, a small capacitor (~0.1µF) from these pins
to GND may improve the light load transient response by
delaying the transition from the discontinuous to forced
continuous switching modes. MODE may be tied to GND
for the purpose of blocking reverse current if no output
current sense resistor is used.
FB Resistor Divider and Load Regulation
8055 F05b
Figure 5b. This Comparator Circuit Turns Off the LTM8055/
LTM8055-1 if the Input Rises Above a Predetermined
Threshold. When the LTM8055/LTM8055-1 Turns Off, the
Energy Stored in the Internal Inductor Will Raise VIN a Small
Amount Above the Threshold
Switching Mode
The MODE pin allows the user to select either discontinuous
mode or forced continuous mode switching operation. In
forced continuous mode, the LTM8055/LTM8055-1 will not
skip cycles, even when the internal inductor current falls
to zero or even reverses direction. This has the advantage
of operating at the same fixed frequency for all load conditions, which can be useful when designing to EMI or output
noise specifications. Forced continuous mode, however,
uses more current at light loads, and allows current to flow
from the load back into the input if the output is raised
above the regulation point. This reverse current can raise
the input voltage and be hazardous if the input is allowed
to rise uncontrollably. Please refer to Input Precautions
in this section for a discussion of this behavior.
Forced continuous operation may provide improved output
regulation when the LTM8055/LTM8055-1 transitions
The LTM8055/LTM8055-1 regulates its FB pin to 1.2V,
using a resistor divider to sense the output voltage. The
location at which the output voltage is sensed affects
the load regulation. If there is a current sense resistor
between VOUT and IOUT, and the output is sensed at VOUT,
the voltage at the load will drop by the value of the current sense resistor multiplied by the output current. If the
output voltage can be sensed at IOUT, the load regulation
may be improved.
PCB Layout
Most of the headaches associated with PCB layout have
been alleviated or even eliminated by the high level of
integration of the LTM8055/LTM8055-1. The LTM8055/
LTM8055-1 is nevertheless a switching power supply, and
care must be taken to minimize EMI and ensure proper
operation. Even with the high level of integration, you may
fail to achieve specified operation with a haphazard or poor
layout. See Figure 6 for a suggested layout. Ensure that
the grounding and heat sinking are acceptable.
A few rules to keep in mind are:
1. Place the RFB and RT resistors as close as possible to
their respective pins.
Rev C
For more information www.analog.com
15
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
2. Place the CIN capacitor as close as possible to the VIN
and GND connection of the LTM8055/LTM8055-1.
board. Pay attention to the location and density of the
thermal vias in Figure 6. The LTM8055/LTM8055-1 can
benefit from the heat sinking afforded by vias that connect to internal GND planes at these locations, due to
their proximity to internal power handling components.
The optimum number of thermal vias depends upon
the printed circuit board design. For example, a board
might use very small via holes. It should employ more
thermal vias than a board that uses larger holes.
3. Place the COUT capacitor as close as possible to the
VOUT and GND connection of the LTM8055/LTM8055-1.
4. Minimize the trace resistance between the optional
output current sense resistor, ROUT, and VOUT. Minimize
the loop area of the IOUT trace and the trace from VOUT
to ROUT.
5. Minimize the trace resistance between the optional input
current sense resistor, RIN and VIN. Minimize the loop
area of the IIN trace and the trace from VIN to RIN.
6. Place the CIN and COUT capacitors such that their
ground current flow directly adjacent or underneath
the LTM8055/LTM8055-1.
7. Connect all of the GND connections to as large a copper
pour or plane area as possible on the top layer. Avoid
breaking the ground connection between the external
components and the LTM8055/LTM8055-1.
8. Use vias to connect the GND copper area to the board’s
internal ground planes. Liberally distribute these GND
vias to provide both a good ground connection and
thermal path to the internal planes of the printed circuit
Hot-Plugging Safely
The small size, robustness and low impedance of ceramic
capacitors make them an attractive option for the input
bypass capacitor of LTM8055/LTM8055-1. However, these
capacitors can cause problems if the LTM8055/LTM8055-1
is plugged into a live supply (see Linear Technology Application Note 88 for a complete discussion). The low
loss ceramic capacitor combined with stray inductance
in series with the power source forms an underdamped
tank circuit, and the voltage at the VIN pin of the LTM8055/
LTM8055-1 can ring to more than twice the nominal input
voltage, possibly exceeding the LTM8055/LTM8055-1’s
rating and damaging the part. If the input supply is poorly
controlled or the LTM8055/LTM8055-1 is hot-plugged into
CIN
GND
SVIN
VIN
GND/THERMAL VIAS
RIN
INPUT
SENSE
IIN
COUT
INPUT
RUN
VOUT SIGNAL VIA
VOUT
MODE SYNC
IOUT
IOUT
LL
RT
FB
ROUT
OUTPUT
SENSE
GND
VOUT SIGNAL VIA
8055 F06
Figure 6. Layout Showing Suggested External Components,
GND Plane and Thermal Vias
Rev C
16
For more information www.analog.com
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
an energized supply, the input network should be designed
to prevent this overshoot. This can be accomplished by
installing a small resistor in series with VIN, but the most
popular method of controlling input voltage overshoot is
to add an electrolytic bulk capacitor to the VIN net. This
capacitor’s relatively high equivalent series resistance
damps the circuit and eliminates the voltage overshoot.
The extra capacitor improves low frequency ripple filtering and can slightly improve the efficiency of the circuit,
though it is likely to be the largest component in the circuit.
Thermal Considerations
The LTM8055/LTM8055-1 output current may need to be
derated if it is required to operate in a high ambient temperature or deliver a large amount of continuous power.
The amount of current derating is dependent upon the
input voltage, output power and ambient temperature. The
temperature rise curves given in the Typical Performance
Characteristics section can be used as a guide. These curves
were generated by a LTM8055/LTM8055-1 mounted to a
58cm2 4-layer FR4 printed circuit board. Boards of other
sizes and layer count can exhibit different thermal behavior,
so it is incumbent upon the user to verify proper operation
over the intended system’s line, load and environmental
operating conditions.
The thermal resistance numbers listed in the Pin Configuration of the data sheet are based on modeling the µModule
package mounted on a test board specified per JESD 51-9
(Test Boards for Area Array Surface Mount Package Thermal
Measurements). The thermal coefficients provided on this
page are based on JESD 51-12 (Guidelines for Reporting
and Using Electronic Package Thermal Information).
For increased accuracy and fidelity to the actual application,
many designers use FEA to predict thermal performance.
To that end, the Pin Configuration of the data sheet typically gives four thermal coefficients:
θJA – Thermal resistance from junction to ambient.
θJCbottom – Thermal resistance from junction to the bottom
of the product case.
θJB – Thermal resistance from junction to the printed
circuit board.
While the meaning of each of these coefficients may seem
to be intuitive, JEDEC has defined each to avoid confusion
and inconsistency. These definitions are given in JESD
51-12, and are quoted or paraphrased below:
θJA is the natural convection junction-to-ambient air
thermal resistance measured in a one cubic foot sealed
enclosure. This environment is sometimes referred to as
“still air” although natural convection causes the air to
move. This value is determined with the part mounted to
a JESD 51-9 defined test board, which does not reflect an
actual application or viable operating condition.
θJCbottom is the thermal resistance between the junction
and bottom of the package with all of the component power
dissipation flowing through the bottom of the package. In
the typical µModule converter, the bulk of the heat flows
out the bottom of the package, but there is always heat
flow out into the ambient environment. As a result, this
thermal resistance value may be useful for comparing
packages but the test conditions don’t generally match
the user’s application.
θJCtop is determined with nearly all of the component power
dissipation flowing through the top of the package. As the
electrical connections of the typical µModule converter are
on the bottom of the package, it is rare for an application
to operate such that most of the heat flows from the junction to the top of the part. As in the case of θJCbottom, this
value may be useful for comparing packages but the test
conditions don’t generally match the user’s application.
θJB is the junction-to-board thermal resistance where
almost all of the heat flows through the bottom of the
µModule converter and into the board, and is really the
sum of the θJCbottom and the thermal resistance of the
bottom of the part through the solder joints and through a
portion of the board. The board temperature is measured
a specified distance from the package, using a 2-sided,
2-layer board. This board is described in JESD 51-9.
θJCtop – Thermal resistance from junction to top of the
product case.
Rev C
For more information www.analog.com
17
LTM8055/LTM8055-1
APPLICATIONS INFORMATION
JUNCTION-TO-AMBIENT RESISTANCE (JESD 51-9 DEFINED BOARD)
CASE (TOP)-TO-AMBIENT
RESISTANCE
JUNCTION-TO-CASE (TOP)
RESISTANCE
JUNCTION
JUNCTION-TO-BOARD RESISTANCE
AMBIENT
JUNCTION-TO-CASE
CASE (BOTTOM)-TO-BOARD
(BOTTOM) RESISTANCE
RESISTANCE
BOARD-TO-AMBIENT
RESISTANCE
8055 F07
µMODULE CONVERTER
Figure 7
Given these definitions, it should now be apparent that none
of these thermal coefficients reflects an actual physical
operating condition of a µModule converter. Thus, none
of them can be individually used to accurately predict the
thermal performance of the product. Likewise, it would
be inappropriate to attempt to use any one coefficient to
correlate to the junction temperature versus load graphs
given in the product’s data sheet. The only appropriate way
to use the coefficients is when running a detailed thermal
analysis, such as FEA, which considers all of the thermal
resistances simultaneously.
A graphical representation of these thermal resistances
is given in Figure 7.
The blue resistances are contained within the µModule
converter, and the green are outside.
The die temperature of the LTM8055/LTM8055-1 must be
lower than the maximum rating of 125°C, so care should
be taken in the layout of the circuit to ensure good heat
sinking of the LTM8055/LTM8055-1. The bulk of the heat
flow out of the LTM8055/LTM8055-1 is through the bottom
of the μModule converter and the BGA pads into the printed
circuit board. Consequently a poor printed circuit board
design can cause excessive heating, resulting in impaired
performance or reliability. Please refer to the PCB Layout
section for printed circuit board design suggestions.
Rev C
18
For more information www.analog.com
LTM8055/LTM8055-1
TYPICAL APPLICATIONS
12VOUT Fan Power from 3VIN to 36VIN with Analog
Current Control and 2A Input Current Limiting
Maximum Output Current
vs CTL Voltage
1µF
50V
VIN
IIN
SVIN
LTM8055/
LTM8055-1
0.05Ω
VOUT
VOUT
12V MAX
IOUT
FAN
10µF
50V
RUN
COMP
SS
SYNC
CTL
RT LL MODE
36.5k
100k
GND
CLKOUT
IINMON
IOUTMON
FB
22µF
25V
+
68µF
25V
11.0k
0.8
0.6
0.4
0.2
8055 TA02a
0
fSW = 600kHz
0.2V TO 1.2V
CONTROL RANGE
DAC
12VIN
1.0
OUTPUT CURRENT (A)
VIN
3V TO 36V
0.022Ω
1.2
0
0.2
0.4
0.6
0.8
CTL VOLTAGE (V)
1
1.2
8055 TA02b
FAN CONTROL
24VOUT from 7VIN to 36VIN with 2.1A Accurate Current Limit
Output Voltage vs Output Current
VIN
VIN
7V TO 36V
SVIN
LTM8055/
LTM8055-1
VOUT
0.027Ω
IOUT
VOUT
24V
25
12VIN
IIN
36.5k
RUN
COMP
SS
SYNC
CTL
RT
LL MODE
100k
GND
CLKOUT
IINMON
IOUTMON
FB
22µF
25V
+
33µF
35V
5.23k
8055 TA03a
fSW = 600kHz
OUTPUT VOLTAGE (V)
10µF
50V
20
15
10
5
0
0
0.5
1
1.5
2
OUTPUT CURRENT (A)
2.5
8055 TA03b
Rev C
For more information www.analog.com
19
LTM8055/LTM8055-1
TYPICAL APPLICATIONS
3.3VOUT from 9VIN to 24VIN with 5A Accurate Current Limit and
Output Current Monitor
Output Voltage vs Output Current
4.0
VIN
VIN
9V TO 24V
LTM8055/
LTM8055-1
SVIN
VOUT
0.011Ω
IOUT
VOUT
3.3V
3.5
10µF
50V
36.5k
RUN
CTL
SS
SYNC
COMP
RT
LL
100k
MODE
GND
CLKOUT
IINMON
IOUTMON
FB
22µF
6.3V
OUTPUT
CURRENT
MONITOR
+
56.2k
OUTPUT VOLTAGE (V)
IIN
100µF
6.3V
3.0
2.5
2.0
1.5
1.0
0.5
8055 TA04a
0
fSW = 600kHz
0
1
2
3
4
OUTPUT CURRENT (A)
5
6
8055 TA04b
Two LTM8055/LTM8055-1s Paralleled to Get More Output Current. The Two
µModules Are Synchronized and Switching 180° Out Of Phase
VIN
LTM8055/
LTM8055-1
(MASTER)
SVIN
IIN
36.5k
47pF
0.008Ω
IOUT
VOUT
12V
1.2
1.0
RUN
CTL
SS
SYNC
COMP
RT
CLKOUT
LL MODE
IINMON
IOUTMON
FB
22µF
25V
100k
+
11k
GND
+
68µF
25V
VIOUTMON (V)
10µF
50V
VOUT
0.8
0.6
0.4
–
VIN
7V TO 36V
IOUTMON Voltage vs Output Current
for Each Channel, 12VIN
LT1636
0.2
0
VIN
LTM8055/
LTM8055-1
(SLAVE)
SVIN
IIN
10µF 47pF
50V
RUN
COMP
SS
SYNC
36.5k
RT
LL MODE
GND
VOUT
0.008Ω
IOUT
CTL
CLKOUT
IINMON
IOUTMON
FB
MASTER
SLAVE
0
5
10
15
COMBINED CURRENTS OF BOTH CHANNELS (A)
8055 TA05b
22µF
25V
+
68µF
25V
100k
9.31k
8055 TA05a
fSW = 600kHz
Rev C
20
For more information www.analog.com
LTM8055/LTM8055-1
TYPICAL APPLICATIONS
Two LTM8055/LTM8055-1s Powered from Different Input Sources to Run a Single Load. Each LTM8055/LTM8055-1 Draws No More
Than 1.8A from Its Respective Power Source, and Are Synchronized 180° Out Of Phase with Each Other
0.025Ω
SUPPLY 1
6V TO 36VIN
VIN
SVIN
LTM8055/
LTM8055-1
IOUT
IIN
10µF
50V
RUN
CTL
SS
SYNC
COMP
RT
CLKOUT
LL MODE
47pF
36.5k
0.025Ω
SUPPLY 2
6V TO 36VIN
VIN
SVIN
VOUT
IINMON
IOUTMON
FB
11k
VOUT
IOUT
IIN
10µF
50V
100k
RUN
CTL
SS
SYNC
COMP
RT
LL MODE
47pF
36.5k
68µF
35V
100k
GND
LTM8055/
LTM8055-1
+
22µF
25V
3A MAX
VOUT
12V
22µF
25V
GND
CLKOUT
IINMON
IOUTMON
FB
11k
8055 TA06a
fSW = 600kHz
Input Current and Output Voltage vs
Output Current 12VIN
14
2.5
12
10
1.5
8
6
1.0
0.5
0
0
VOUT (V)
INPUT CURRENT (A)
2.0
4
VOUT
INPUT CURRENT,
REGULATOR 1 2
INPUT CURRENT,
REGULATOR 2 0
1
2
3
4
OUTPUT CURRENT (A)
8055 TA06b
Rev C
For more information www.analog.com
21
LTM8055/LTM8055-1
PACKAGE DESCRIPTION
Table 4. LTM8055/LTM8055-1 Pin Assignment (Arranged by Pin Number)
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
A1
VOUT
B1
VOUT
C1
VOUT
D1
IOUT
E1
GND
F1
LL
A2
VOUT
B2
VOUT
C2
VOUT
D2
GND
E2
GND
F2
GND
A3
VOUT
B3
VOUT
C3
VOUT
D3
GND
E3
GND
F3
GND
A4
VOUT
B4
VOUT
C4
VOUT
D4
GND
E4
GND
F4
GND
A5
VOUT
B5
VOUT
C5
VOUT
D5
GND
E5
GND
F5
GND
A6
VOUT
B6
VOUT
C6
VOUT
D6
GND
E6
GND
F6
GND
A7
GND
B7
GND
C7
GND
D7
GND
E7
GND
F7
GND
A8
GND
B8
GND
C8
GND
D8
GND
E8
GND
F8
GND
A9
GND
B9
GND
C9
GND
D9
GND
E9
GND
F9
GND
A10
GND
B10
GND
C10
GND
D10
GND
E10
GND
F10
SVIN
A11
GND
B11
GND
C11
GND
D11
GND
E11
GND
F11
SVIN
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
PIN ID
FUNCTION
G1
CLKOUT
H1
RT
J1
FB
K1
SS
L1
GND
G2
MODE
H2
SYNC
J2
COMP
K2
CTL
L2
IOUTMON
G3
GND
H3
GND
J3
GND
K3
GND
L3
IINMON
G4
GND
H4
GND
J4
GND
K4
GND
L4
RUN
G5
GND
H5
GND
J5
GND
K5
GND
L5
GND
G6
GND
H6
GND
J6
GND
K6
GND
L6
GND
G7
GND
H7
GND
J7
GND
K7
GND
L7
GND
G8
GND
H8
GND
J8
GND
K8
GND
L8
GND
G9
GND
H9
GND
J9
GND
K9
GND
L9
IIN
G10
VIN
H10
VIN
J10
VIN
K10
VIN
L10
VIN
G11
VIN
H11
VIN
J11
VIN
K11
VIN
L11
VIN
Rev C
22
For more information www.analog.com
LTM8055/LTM8055-1
PACKAGE PHOTO
Rev C
For more information www.analog.com
23
0.635 ±0.025 Ø 121x
PACKAGE TOP VIEW
2.540
SUGGESTED PCB LAYOUT
TOP VIEW
1.270
4
0.3175
0.000
0.3175
PIN “A1”
CORNER
E
1.270
aaa Z
2.540
D
X
For more information www.analog.com
6.350
5.080
3.810
2.540
1.270
0.000
1.270
2.540
3.810
5.080
6.350
Y
aaa Z
SYMBOL
A
A1
A2
b
b1
D
E
e
F
G
H1
H2
aaa
bbb
ccc
ddd
eee
H1
SUBSTRATE
NOM
4.92
0.60
4.32
0.78
0.635
15.00
15.00
1.27
12.70
12.70
0.32
4.00
A
A2
MAX
5.12
0.70
4.42
0.85
0.660
NOTES
DETAIL B
PACKAGE SIDE VIEW
0.37
4.05
0.15
0.10
0.20
0.30
0.15
TOTAL NUMBER OF BALLS: 121
0.27
3.95
MIN
4.72
0.50
4.22
0.71
0.610
b1
DIMENSIONS
ddd M Z X Y
eee M Z
DETAIL A
Øb (121 PLACES)
DETAIL B
H2
MOLD
CAP
ccc Z
A1
(Reference LTC DWG# 05-08-1891 Rev A)
// bbb Z
24
Z
Z
BGA Package
121-Lead (15.00mm × 15.00mm × 4.92mm)
F
11
10
9
7
6
5
4
PACKAGE BOTTOM VIEW
8
G
3
2
1
DETAIL A
DETAILS OF PIN #1 IDENTIFIER ARE OPTIONAL,
BUT MUST BE LOCATED WITHIN THE ZONE INDICATED.
THE PIN #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE
4
L
K
J
H
G
F
E
D
C
B
A
7
TRAY PIN 1
BEVEL
!
PACKAGE IN TRAY LOADING ORIENTATION
LTMXXXXXX
µModule
7
SEE NOTES
PIN 1
BGA 121 1112 REV A
PACKAGE ROW AND COLUMN LABELING MAY VARY
AMONG µModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY
6. SOLDER BALL COMPOSITION CAN BE 96.5% Sn/3.0% Ag/0.5% Cu
OR Sn Pb EUTECTIC
5. PRIMARY DATUM -Z- IS SEATING PLANE
BALL DESIGNATION PER JESD MS-028 AND JEP95
3
2. ALL DIMENSIONS ARE IN MILLIMETERS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994
e
COMPONENT
PIN “A1”
b
3
SEE NOTES
LTM8055/LTM8055-1
PACKAGE DESCRIPTION
Rev C
6.350
5.080
3.810
3.810
5.080
6.350
LTM8055/LTM8055-1
REVISION HISTORY
REV
DATE
DESCRIPTION
A
01/16
Added Buck-Bost Selection Table
PAGE NUMBER
1
B
05/17
Added text to IOUTMON (pin L2)
8
C
08/18
Added LTM8055-1
1, 2, 7, 9, 10,
23
Rev C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications
subject to change without notice. No license For
is granted
implication or
otherwise under any patent or patent rights of Analog Devices.
morebyinformation
www.analog.com
25
LTM8055/LTM8055-1
TYPICAL APPLICATION
Input Current vs Input Voltage,
IOUT = 3A
14.4V, 3A Lead-Acid Battery Charger Input Current Limited to 2.1A
2.5
1µF
50V
0.022Ω
VIN SVIN
IIN
0.02Ω
VOUT
LTM8055/
LTM8055-1
IOUT
+
100k
10µF
50V
36.5k
RUN
CTL
SS
SYNC
COMP
RT
47µF
25V
1.5
1.0
0.5
CLKOUT
IINMON
IOUTMON
FB
LL MODE GND
VOUT
14.4V
INPUT CURRENT (A)
VIN
3V TO 36V
2.0
22µF
25V
0
9.09k
8055 TA07a
0
10
20
30
INPUT VOLTAGE (V)
40
8055 TA07b
fSW = 600kHz
DESIGN RESOURCES
SUBJECT
DESCRIPTION
µModule Design and Manufacturing Resources
Design:
•
Selector Guides
•
Demo Boards and Gerber Files
•
Free Simulation Tools
µModule Regulator Products Search
1. Sort table of products by parameters and download the result as a spread sheet.
Manufacturing:
•
Quick Start Guide/Demo Manual
•
PCB Design, Assembly and Manufacturing Guidelines
•
Package and Board Level Reliability
2. Search using the Quick Power Search parametric table.
Digital Power System Management
Analog Devices’ family of digital power supply management ICs are highly integrated solutions that
offer essential functions, including power supply monitoring, supervision, margining and sequencing,
and feature EEPROM for storing user configurations and fault logging.
RELATED PARTS
PART NUMBER DESCRIPTION
COMMENTS
LTM4605
Higher Power Buck-Boost (Up to 60W)
External Inductor, Synchronous Switching Buck-Boost; Up to 36VIN, 0.8V ≤ VOUT ≤ 16V
LTM4607
Higher Power Buck-Boost (Up to 60W)
External Inductor, Synchronous Switching Buck-Boost; Up to 36VIN, 0.8V ≤ VOUT ≤ 24V
LTM4609
Higher Power Buck-Boost (Up to 60W)
External Inductor, Synchronous Switching Buck-Boost; Up to 36VIN, 0.8V ≤ VOUT ≤ 34V
LTM8045
Smaller, Lower Power
SEPIC and Inverting; 700mA, 6.25mm × 11.25mm × 4.92mm BGA
LTM8046
Isolated, Lower Power
Flyback Topology, 550mA (5VOUT, 24VIN), UL60950, 2kVAC
Rev C
26
D17085-0-8/18(C)
www.analog.com
For more information www.analog.com
ANALOG DEVICES, INC. 2015-2018
工商网监
湘ICP备2023018690号
