LT1120A

LT1120A Micropower Regulator with Comparator and Shutdown FEATURES s s s s s s s s s DESCRIPTIO 20µA Supply Current 125mA Output Current 2.5V Reference Reference Output Sources 4mA and Sinks 4mA Open Collector Comparator Sinks 10mA Logic Shutdown 0.2V Dropout Voltage Thermal Limiting 8-Lead SO Package The LT®1120A is a combination micropower positive regulator and free collector comparator on a single monolithic chip. With only 20µA supply current, the LT1120A can supply over 125mA of output current. Input voltage range is from 4.5V to 36V and dropout voltage is 0.6V at 125mA. Dropout voltage decreases with lower load currents. Also included on the chip is a class B output 2.5V reference that can either source or sink current. This allows it to be used as a supply splitter or auxiliary output. A shutdown pin allows logic shutdown of the output. The comparator can be used for system or battery monitoring. For example, the comparator can be used to warn of low system voltage. Frequency compensation of the comparator for amplifier applications can be obtained by adding external output capacitance. , LTC and LT are registered trademarks of Linear Technology Corporation. APPLICATIO S s s s s s Battery Systems Battery Backup System Portable Terminals Portable Instruments Memory Keep Alive TYPICAL APPLICATIO 5V Regulator Dropout Voltage and Supply Current 1.00 10 LT1120A 10µF 0.001µF FB 2 1M + 3 SHUTDOWN GND 1 + 1M 25µF DROPOUT VOLTAGE (V) VIN > 5.2V IQ = 20µA 5V IN VOUT 4 5V 0.10 1120A TA01 0.01 0.1 1 10 100 OUTPUT CURRENT (mA) U SUPPLY CURRENT (mA) 1 0.1 1000 1120A TA02 U U 1120afa 1 LT1 120A ABSOLUTE MAXIMUM RATINGS (Note 1) PACKAGE/ORDER INFORMATION TOP VIEW GND 1 FEEDBACK 2 SHUTDOWN 3 VOUT 4 N8 PACKAGE 8-LEAD PDIP 8 7 6 5 –INPUT COMP OUT REF VIN Input Voltage ........................................................... 36V NPN Collector Voltage ............................................. 36V Output Short-Circuit Duration .......................... Indefinite Power Dissipation ............................... Internally Limited Operating Temperature Range LT1120AC ............................................. 0°C to 100°C LT1120AI ......................................... – 40°C to 100°C Storage Temperature Range ................. – 65°C to 150°C ORDER PART NUMBER LT1120ACN8 LT1120ACS8 LT1120AIS8 S8 PART MARKING 1120A 1120AI S8 PACKAGE 8-LEAD PLASTIC SO TJMAX = 110°C, θJA = 130°C/W (N) TJMAX = 110°C, θJA = 190°C/W (S) Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS PARAMETER Reference Reference Voltage Line Regulation Load Regulation Output Source Current Output Sink Current Temperature Stability Regulator Supply Current CONDITIONS TJ = 25°C MIN 2.46 TYP 2.50 0.01 0.3 4 4 1 20 30 11 125 0.2 0.01 0.02 0.40 2.5 1.4 10 15 1 250 3 15 10000 96 18 0.4 5 0.5 0.015 0.05 0.65 2.56 0.4 MAX 2.54 0.015 0.6 UNITS V %/V % mA mA % µA µA mA mA % %/V V V V V V µA nA µA mA mV nA V/V dB mA V V µs µA 1120afa 4.5V ≤ VIN ≤ 36V 4.5V ≤ VIN ≤ 36V –2.0mA ≤ IREF ≤ 2mA, VIN = 12V VIN = 5V VIN = 5V 2 2 Output Current Load Regulation Line Regulation Dropout Voltage Feedback Sense Voltage Shutdown Pin Voltage Shutdown Pin Current Feedback Bias Current Minimum Load Current Short-Circuit Current Comparator Offset Voltage Bias Current Gain Power Supply Rejection Output Sink Current Saturation Voltage Input Voltage Range Response Time Leakage Current VIN = 6V, IOUT ≤ 100mA VIN = 36V, IOUT ≤ 100mA VIN = 12V, IOUT = 125mA (VIN – VOUT) ≥ 1V, VIN ≥ 6V (VIN – VOUT) ≥ 1V, VIN ≥ 6V 6V ≤ VIN ≤ 36V IOUT = 100mA IOUT = 125mA VIN = 12V Normal VOUT ≤ 0.5V Shutdown VIN = 1.4V VIN = 36V VIN = 36V VIN = 36V VIN = 36V ∆VOUT = 29V, RL = 20k 4.5V ≤ VS ≤ 36V VIN = 4.5V IOUT = 1mA 25 40 20 2.44 2.2 40 5 400 7 40 2000 80 10 0 0.6 VIN – 1 2 VIN = 36V, V(Pin 7) = 36V 2 U W U U WW W LT1120A ELECTRICAL CHARACTERISTICS PARAMETER Reference Reference Voltage Line Regulation Load Regulation Output Source Current Output Sink Current Regulator Supply Current CONDITIONS The q denotes the specifications which apply over the full operating temperature range of TJ = 25°C. MIN q q q q q q q q q q q q q q q q q q q q q q TYP 2.50 0.01 0.4 MAX 2.55 0.02 0.8 UNITS V %/V % mA mA µA µA mA mA % %/V V V V nA µA mA mV nA V/V mA µA 4.5V ≤ VIN ≤ 36V 4.5V ≤ VIN ≤ 36V –2.0mA ≤ IREF ≤ 2mA, VIN = 12V VIN = 5V VIN = 5V VIN = 6V, IOUT ≤ 100µA VIN = 36V, IOUT ≤ 100µA VIN = 12V, IOUT = 125mA (VIN – VOUT) ≥ 1V, VIN ≥ 6V (VIN – VOUT) ≥ 1V, VIN ≥ 6V 6V ≤ VIN ≤ 36V IOUT = 100µA IOUT = 125mA VIN = 12V VIN = 36V VIN = 36V VIN = 36V VIN = 36V ∆VOUT = 29V, RL = 20k VIN = 4.5V VIN = 36V, V(Pin 7) = 36V 2.40 2 2 30 40 11 125 1 0.02 0.06 0.85 2.57 50 50 400 10 60 40 50 20 Output Current Load Regulation Line Regulation Dropout Voltage Feedback Sense Voltage Feedback Bias Current Minimum Load Current Short-Circuit Current Comparator Offset Voltage Bias Current Gain Output Sink Current (Note 2) Leakage Current 2.38 2.5 240 15 1000 5 10 8 Note 1: Absolute Maximum Ratings are those values beyond which the life to the device may be impaired. Note 2: For TA ≤ – 40°C output sink current drops to 2.5mA. TYPICAL PERFOR A CE CHARACTERISTICS Regulator Load Regulation 0.3 PRE-LOAD = 100µA 100 TJ = –55°C SUPPLY CURRENT (mA) TJ = 25°C 0.1 0 TJ = 125°C –0.1 –0.2 –0.3 0.1 10 SHORT-CIRCUIT CURRENT (mA) OUTPUT VOLTAGE CHANGE (%) 0.2 1 100 10 OUTPUT CURRENT (mA) UW 1120A G01 Supply Current 350 300 250 200 150 100 50 Regulator Short-Circuit Current 1 0.1 1000 0.01 0.1 10 100 1 1000 REGULATOR OUTPUT CURRENT (mA) 1120A G02 0 –50 –10 30 70 110 TEMPERATURE (°C) 150 1120A G03 1120afa 3 LT1 120A TYPICAL PERFOR A CE CHARACTERISTICS Dropout Voltage REGULATOR INPUT-OUTPUT DIFFERENTIAL (V) 1 ∆VOUT = 100mV MINIMUM LOAD CURRENT (µA) RIPPLE REJECTION (dB) 0.1 0.01 0.1 10 100 1 1000 REGULATOR OUTPUT CURRENT (mA) 1120A G04 Supply Current 10 IOUT = 100mA SUPPLY CURRENT (mA) 1 SUPPLY CURRENT (mA) REFERENCE VOLTAGE CHANGE (mV) 0.1 IOUT = 10mA IOUT = 1mA 0.01 VOUT = 5V 0.01 1 5 20 15 10 25 REGULATOR INPUT-OUTPUT DIFFERENTIAL (V) 1120A G07 OUTPUT VOLTAGE CHANGE (%) Feedback Pin Current 40 35 FEEDBACK PIN CURRENT (nA) 25 20 15 10 5 0 0.1 10 100 1 1000 REGULATOR OUTPUT CURRENT (mA) 1120A G10 OUTPUT VOLTAGE (V) 30 TJ = –55°C OUTPUT CURRENT (mA) TJ = 25°C TJ = 125°C 4 UW Regulator Minimum Load Current 100 70 65 60 55 50 45 40 35 Regulator Ripple Rejection IOUT = 100mA 10 IOUT = 10mA IOUT = 1mA VIN = 10VDC, 1VP-P VOUT = 5V COUT = 10µF 10 100 1k 10k RIPPLE FREQUENCY (Hz) 100k 1120A G06 1 70 80 90 100 110 120 130 140 150 TEMPERATURE (°C) 1120A G05 30 Supply Current at Dropout 10 IOUT = 100mA 1 4 3 2 1 0 –1 –2 –3 Reference Regulation 0.1 IOUT = 10mA IOUT = 1mA 0 0.1 0.5 0.3 0.4 0.2 0.6 REGULATOR INPUT-OUTPUT DIFFERENTIAL (V) 1120A G08 –4 –1.5 –1.0 –0.5 0.5 1.0 0 REFERENCE OUTPUT CURRENT (mA) 1.5 1120A G09 Regulator Thermal Regulation 0.1 VIN = 15V VOUT = 5V 0 Turn-On Characteristic 5.5 VOUT = 5V 5.0 NO LOAD 4.5 4.0 3.5 3.0 2.5 2.0 RL = 50Ω 0 1 2 3 4 5 6 INPUT VOLTAGE (V) 7 8 RL = 500Ω –0.1 50 0 0 20 40 60 80 100 120 140 160 180 TIME (ms) 1120A G11 0 1120A G12 1120afa LT1120A PI FU CTIO S GND (Pin 1): Ground FEEDBACK (Pin 2): This is the feedback point of the regulator. When operating, it is nominally at 2.5V. Optimum source resistance is 200k to 500k. The feedback pin should not be driven below ground or more positive than 5V. SHUTDOWN (Pin 3): A logic 1 shuts off main regulator. Caution: noise or leakage into the shutdown pin can affect output voltage. VOUT (Pin 4): Main output, requires 10µF output capacitor. Can be shorted to VIN or ground without damaging device. VIN (Pin 5): Input Supply. Bypass with 10µF capacitor. Must always be more positive than ground. REF (Pin 6): Reference. 2.5V can source or sink current. May be shorted to ground or up to 5V. Voltages in excess of 5V can damage the device. COMP OUT (Pin 7): Open Collector NPN Output. May be connected to any voltage from ground to 36V more positive than ground (operates above VIN). Short-circuit protected. –INPUT (Pin 8): Inverting Comparator Input. BLOCK DIAGRA APPLICATIO S I FOR ATIO The LT1120A is especially suited for micropower system applications. For example, the comparator section of the LT1120A may be used as a battery checker to provide an indication of low battery. Another type of system application for the LT1120A would be to generate the equivalent of split supplies off of a single power input. The regulator section provides regulated output voltage and the reference, which can both source and sink current is then an artificial system ground providing a split supply for the system. U W W UU U U U REF 6 VIN 5 + COMP OUT 7 100k – REF 2.5V 120k 3 1 8 –INPUT SHUTDOWN GROUND 4 2 VOUT FEEDBACK 1120A BD01 For many applications the comparator can be frequency compensated to operate as an amplifier. Compensation values for various gains are given in the data sheet. The comparator gain is purposely low to make it easier to frequency compensate as an amplifier. The NPN output is capable of sinking 10mA and can drive loads connected to voltages in excess of the positive power supply. This is useful for driving switches or linear regulators off of a higher input voltage. 1120afa 5 LT1 120A APPLICATIONS INFORMATION Reference Internal to the LT1120A is a 2.5V trimmed class B output reference. The reference was designed to be able to source or sink current so it could be used in supply splitting applications as well as a general purpose reference for external circuitry. The design of the reference allows it to source and sink typically 4mA. The available source and sink current decreases as temperature increases. It is sometimes desirable to decrease the AC output impedance by placing an output capacitor on Pin 6. The reference in the LT1120A becomes unstable with large capacitive loads placed directly on it. When using an output capacitor, about 20Ω should be used to isolate the capacitor from the reference pin. This 20Ω resistor can be placed directly in series with the capacitor or alternatively the reference line can have 20Ω placed in series with it and then a capacitor to ground. This is shown in Figure 1. Other than placing large capacitive loads on the reference, no other precautions are necessary and the reference is stable with nominal stray capacitances. REF 6 OUTPUT 20Ω REF 6 20Ω + OR 10µF + OUTPUT 10µF 1120A AI01 Figure 1. Bypassing Reference Overload Protection The main regulator in the LT1120A is current limited at approximately 250mA. The current limit is stable with both input voltage and temperature. 6 U W U U Like most other IC regulators, a minimum load is required on the output of the LT1120A to maintain regulation. For most standard regulators this is normally specified at 5mA. Of course, for a micropower regulator this would be a tremendously large current. The output current must be large enough to absorb all the leakage current of the pass transistor at the maximum operating temperature. It also affects the transient response; low output currents have long recovery times from load transients. At high operating temperatures the minimum load current increases and having too low of a load current may cause the output to go unregulated. Devices are tested for minimum load current at high temperature. The output voltage setting resistors to the feedback terminal can usually be used to provide the minimum load current. Frequency Compensation The LT1120A is frequency compensated by a dominant pole on the output. An output capacitor of 10µF is usually large enough to provide good stability. Increasing the output capacitor above 10µF further improves stability. In order to ensure stability, a feedback capacitor is needed between the output pin and the feedback pin. This is because stray capacitance can form another pole with the large value of feedback resistors used with the LT1120A. Also, a feedback capacitor minimizes noise pickup and improves ripple rejection. With the large dynamic operating range of the output current, 10000:1, frequency response changes widely. Low AC impedance capacitors are needed to insure stability. While solid tantalum are best, aluminum electrolytics can be used but larger capacitor values may be needed. 1120afa LT1120A TYPICAL APPLICATIO S Regulator with Output Voltage Monitor 5 5V LOGIC LOGIC OUTPUT 500k 7 VIN OUTPUT 4 0.001µF OUTPUT 5V 10µF VOUT PIN 7 LOGIC OUTPUT GOES LOW WHEN VOUT DROPS BY 100mV Compensating the Comparator as an Op Amp 50µA VREF 6 + – 7 IN R2 1M C2 R1 C1 LT1120A GND 1 AV –1 –10 –100 R1 33Ω 100Ω 10k C1 0.1µF 0.047µF 0.002µF C2 R2 0.001µF 1M – 100k – 10k BATTERY INPUT 5 VIN LT1120A GND 1 INTERNAL PARASITIC DIODES OF LT1120A VIN VOUT Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U – LT1120A 8 2 + 98k 2k 100k 1120A TA03 + FEEDBACK REF 6 GND 1 LOGIC OUTPUT Current Limited 1 Amp Regulator 2.2k MJE2955 0.5Ω* 2N3906* VOUT 5V AT 1A 220µF† VIN AT AV = 100, SLEW RATE = +0.05V/µs – 6V/µs 5 VIN 0.22µF VOUT 4 FB 2 270Ω 100k + 1M * SETS CURRENT LIMIT BUT INCREASES DROPOUT VOLTAGE BY 0.5V. † MUST HAVE LOW 1120A TA04 ESR. SEVERAL 100µF CAPACITORS CAN BE PARALLELED. 1120A TA06 Battery Backup Regulator VOUT 5V VOUT FB 4 0.001µF 2 50k 1M 1120A TA05 4 + 1M VOUT LT1120A FB VIN 5 10µF MAIN POWER INPUT 2 GND 1 1120afa 7 LT1 120A PACKAGE DESCRIPTIO .300 – .325 (7.620 – 8.255) .008 – .015 (0.203 – 0.381) .065 (1.651) TYP .120 (3.048) .020 MIN (0.508) MIN .018 ± .003 (0.457 ± 0.076) ( +.035 .325 –.015 +0.889 8.255 –0.381 ) INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) NOTE: 1. DIMENSIONS ARE .010 – .020 × 45° (0.254 – 0.508) .008 – .010 (0.203 – 0.254) .053 – .069 (1.346 – 1.752) 0°– 8° TYP .016 – .050 (0.406 – 1.270) NOTE: 1. DIMENSIONS IN INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) .014 – .019 (0.355 – 0.483) TYP RELATED PARTS PART NUMBER LT1761/LT1762 LT1763 DESCRIPTION 100mA/150mA, Low Noise Micropower, LDO 500mA, Low Noise Micropower, LDO COMMENTS VIN: 1.8V to 20V; VOUT(MIN) = 1.22V; Dropout Voltage = 0.30V; IQ = 20µA; ISD < 1µA; VOUT = Adj, 1.5V, 1.8V, 2V, 2.5V, 2.8V, 3V, 3.3V, 5V; ThinSOTTM/MS8 Packages. Low Noise