LT1815CS6

LT1815 LT1816/LT1817 Single/Dual/Quad 220MHz, 1500V/µs Operational Amplifiers with Programmable Supply Current FEATURES s s s s s s s s s s s s s s s DESCRIPTIO 220MHz Gain-Bandwidth Product 1500V/µs Slew Rate 6.5mA Supply Current per Amplifier Space Saving MSOP and SSOP Packages Ultra Small SOT-23 and Leadless DFN Packages Programmable Current Option 6nV/√Hz Input Noise Voltage Unity-Gain Stable 1.5mV Maximum Input Offset Voltage 8µA Maximum Input Bias Current 800nA Maximum Input Offset Current 50mA Minimum Output Current, VOUT = ± 3V ± 3.5V Minimum Input CMR, VS = ± 5V Specified at ±5V, Single 5V Supplies Operating Temperature Range: – 40°C to 85°C The LT®1815/LT1816/LT1817 are low power, high speed, very high slew rate operational amplifiers with excellent DC performance. The LT1815/LT1816/LT1817 feature higher bandwidth and slew rate, much lower input offset voltage and lower noise and distortion than other devices with comparable supply current. A programmable current option (LT1815 and LT1816A) allows power savings and flexibility by operating at reduced supply current and speed. The circuit topology is a voltage feedback amplifier with the slewing characteristics of a current feedback amplifier. The output drives a 100Ω load to ± 3.8V with ± 5V supplies. On a single 5V supply, the output swings from 1V to 4V with a 100Ω load connected to 2.5V. Harmonic distortion is –70dB for a 5MHz, 2VP-P output driving a 100Ω load in a gain of –1. The LT1815/LT1816/LT1817 are manufactured on Linear Technology’s advanced low voltage complementary bipolar process and are available in a variety of SOT-23, SO, MSOP, SSOP and leadless DFN packages. , LTC and LT are registered trademarks of Linear Technology Corporation. APPLICATIO S s s s s s s s Wideband Amplifiers Buffers Active Filters Video and RF Amplification Communication Receivers Cable Drivers Data Acquisition Systems TYPICAL APPLICATIO Distortion vs Frequency –30 AV = 2 VS = ± 5V VO = 2VP-P RL = 100Ω Programmable Current Amplifier Switches from Low Power Mode to Full Speed Mode DISTORTION (dB) 500Ω 500Ω VIN 5V –40 –50 –60 –70 –80 –90 3RD HARMONIC – LT1815 VOUT 100Ω ISET 2ND HARMONIC 3RD HARMONIC FULL SPEED MODE + HS/LP 40k –100 100k –5V 181567 TA01 U LOW POWER MODE 2ND HARMONIC 1M FREQUENCY (Hz) 10M 181567 TA02 U U 181567fa 1 LT1815 LT1816/LT1817 ABSOLUTE AXI U V –) RATI GS Total Supply Voltage (V + to .......................... 12.6V Differential Input Voltage (Transient Only, Note 2) ..................................... ± 6V Input Voltage .......................................................... ± VS Output Short-Circuit Duration (Note 3) ............ Indefinite Operating Temperature Range ................ – 40°C to 85°C PACKAGE/ORDER I FOR ATIO TOP VIEW OUT 1 V– 2 +IN 3 + – 4 –IN 5V + TOP VIEW OUT 1 V– 2 +IN 3 + – 6 V+ 5 ISET 4 –IN S5 PACKAGE 5-LEAD PLASTIC SOT-23 S6 PACKAGE 6-LEAD PLASTIC SOT-23 TJMAX = 150°C, θJA = 250°C/W (NOTE 9) TJMAX = 150°C, θJA = 230°C/W (NOTE 9) ORDER PART NUMBER LT1815CS5 LT1815IS5 OUT A –IN A +IN A V– 1 2 3 4 S5 PART MARKING LTUP LTVC 8 7 6 5 V+ OUT B –IN B +IN B ORDER PART S6 PART ORDER PART S8 PART ORDER PART NUMBER NUMBER MARKING NUMBER MARKING LT1816CDD LT1815CS6 LTUL 1815 LT1815CS8 LT1816IDD LT1815IS6 1815I LTVD LT1815IS8 TOP VIEW OUT A –IN A +IN A V– V– 1 2 3 4 5 A B 10 9 8 7 6 V+ OUT B –IN B +IN B ISET OUT A 1 –IN A 2 A +IN A 3 V– B 4 TOP VIEW TOP VIEW A B MS8 PACKAGE 8-LEAD PLASTIC MSOP TJMAX = 150°C, θJA = 250°C/W (NOTE 9) MS10 PACKAGE 10-LEAD PLASTIC MSOP TJMAX = 150°C, θJA = 250°C/W (NOTE 9) ORDER PART NUMBER LT1816CMS8 LT1816IMS8 TOP VIEW OUT A –IN A +IN A V+ +IN B –IN B OUT B NC 1 2 3 4 5 6 7 8 + B – – A + MS8 PART MARKING LTWA LTNQ 16 OUT D – 15 –IN D D + 14 +IN D 13 V – + 12 +IN C C – 11 –IN C 10 OUT C 9 NC ORDER PART NUMBER LT1816ACMS LT1816AIMS ORDER PART NUMBER LT1817CGN LT1817IGN GN PART MARKING 1817 1817I GN PACKAGE 16-LEAD PLASTIC SSOP TJMAX = 150°C, θJA = 135°C/W Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grades are identified by a label on the shipping container. 2 U U W WW U W (Note 1) Specified Temperature Range (Note 8) ... – 40°C to 85°C Maximum Junction Temperature ......................... 150°C (DD Package) ................................................... 125°C Storage Temperature Range ................. – 65°C to 150°C (DD Package) ................................... – 65°C to 125°C Lead Temperature (Soldering, 10 sec).................. 300°C TOP VIEW TOP VIEW NC 1 –IN 2 +IN 3 V– 4 – + 8 7 6 5 NC V+ OUT NC OUT A –IN A +IN A V– 1 2 3 4 A B 8 7 6 5 V+ OUT B –IN B +IN B S8 PACKAGE 8-LEAD PLASTIC SO TJMAX = 150°C, θJA = 150°C/W (NOTE 9) DD PACKAGE 8-LEAD (3mm × 3mm) PLASTIC DFN TJMAX = 125°C, θJA = 160°C/W (NOTE 9) UNDERSIDE METAL INTERNALLY CONNECTED TO V – DD PART MARKING* LAAR 8 V+ 7 OUT B 6 –IN B 5 +IN B S8 PACKAGE 8-LEAD PLASTIC SO TJMAX = 150°C, θJA = 150°C/W (NOTE 9) MS10 PART MARKING LTYA LTXX OUT A –IN A +IN A V+ +IN B –IN B OUT B 1 2 3 4 5 6 7 + B – – A + ORDER PART NUMBER LT1816CS8 LT1816IS8 TOP VIEW 14 OUT D – 13 –IN D D + 12 +IN D 11 V – + 10 +IN C C – 9 –IN C 8 OUT C S8 PART MARKING 1816 1816I ORDER PART NUMBER LT1817CS LT1817IS S PACKAGE 14-LEAD PLASTIC SO TJMAX = 150°C, θJA = 100°C/W 181567fa LT1815 LT1816/LT1817 The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C (Note 8). VS = ± 5V, VCM = 0V unless otherwise noted. For the programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V – through 75Ω or less, unless otherwise noted. SYMBOL PARAMETER VOS Input Offset Voltage CONDITIONS (Note 4) TA = 0°C to 70°C TA = – 40°C to 85°C LT1815S6/LT1816A, 40kΩ Between ISET and V – TA = 0°C to 70°C TA = – 40°C to 85°C TA = 0°C to 70°C (Note 7) TA = – 40°C to 85°C (Note 7) TA = 0°C to 70°C TA = – 40°C to 85°C TA = 0°C to 70°C TA = – 40°C to 85°C f = 10kHz f = 10kHz VCM = ± 3.5V Differential Guaranteed by CMRR TA = – 40°C to 85°C VCM = ± 3.5V TA = 0°C to 70°C TA = – 40°C to 85°C Guaranteed by PSRR TA = – 40°C to 85°C VS = ± 2V to ± 5.5V TA = 0°C to 70°C TA = – 40°C to 85°C VOUT = ± 3V, RL = 100Ω, LT1816/LT1817 TA = 0°C to 70°C TA = – 40°C to 85°C VOUT = ± 3V, RL = 500Ω TA = 0°C to 70°C TA = – 40°C to 85°C VOUT = ± 3V, RL = 100Ω TA = 0°C to 70°C TA = – 40°C to 85°C VOUT Maximum Output Swing RL = 500Ω, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C RL = 100Ω, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C 1.5 q q ELECTRICAL CHARACTERISTICS MIN TYP 0.2 MAX 1.5 2.0 3.0 7 9 10 15 30 800 1000 1200 ±8 ± 10 ±12 UNITS mV mV mV mV mV mV µV/°C µV/°C nA nA nA µA µA µA nV/√Hz pA/√Hz MΩ kΩ pF V V dB dB dB Input Offset Voltage (Low Power Mode) (Note 10) ∆VOS ∆T IOS Input Offset Voltage Drift Input Offset Current 2 q q q q q q 10 10 60 IB Input Bias Current –2 q q en in RIN CIN VCM CMRR Input Noise Voltage Density Input Noise Current Density Input Resistance Input Capacitance Input Voltage Range Common Mode Rejection Ratio 6 1.3 5 750 2 q q q q q q q q q q q q q q q q ± 3.5 ± 3.5 75 73 72 ± 4.2 85 Minimum Supply Voltage PSRR Power Supply Rejection Ratio ±1.25 78 76 75 82 81 80 1.5 1.0 0.8 0.7 0.5 0.4 ± 3.8 ±3.7 ± 3.6 ± 3.50 ±3.25 ± 3.15 97 ±2 ±2 V V dB dB dB dB dB dB V/mV V/mV V/mV V/mV V/mV V/mV V V V V V V Channel Separation 100 AVOL Large-Signal Voltage Gain 3 2.5 ± 4.1 ± 3.8 181567fa 3 LT1815 LT1816/LT1817 The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C (Note 8). VS = ± 5V, VCM = 0V unless otherwise noted. For the programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V – through 75Ω or less, unless otherwise noted. SYMBOL PARAMETER IOUT Maximum Output Current CONDITIONS VOUT = ± 3V, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C LT1815S6/LT1816A; 40kΩ Between ISET and V – ; VOUT = ± 3V, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C VOUT = 0V, 1V Overdrive (Note 3) TA = 0°C to 70°C TA = – 40°C to 85°C AV = – 1 (Note 5) TA = 0°C to 70°C TA = – 40°C to 85°C 6VP-P (Note 6) f = 200kHz, RL = 500Ω, LT1815 TA = 0°C to 70°C TA = – 40°C to 85°C f = 200kHz, RL = 500Ω, LT1816/LT1817 TA = 0°C to 70°C TA = – 40°C to 85°C Gain-Bandwidth Product (Low Power Mode) (Note 10) LT1815S6/LT1816A; 40kΩ Between ISET and V – ; f = 200kHz, RL = 500Ω TA = 0°C to 70°C TA = – 40°C to 85°C AV = 1, RL = 500Ω AV = 1, 10% to 90%, 0.1V, RL = 100Ω AV = 1, 50% to 50%, 0.1V, RL = 100Ω AV = 1, 0.1V; RL = 100Ω AV = – 1, 0.1%, 5V AV = 2, f = 5MHz, VOUT = 2VP-P, RL = 500Ω AV = 2, VOUT = 2VP-P, RL = 150Ω AV = 2, VOUT = 2VP-P, RL = 150Ω AV = 1, f = 1MHz LT1815 TA = 0°C to 70°C TA = – 40°C to 85°C LT1816/LT1817, per Amplifier TA = 0°C to 70°C TA = – 40°C to 85°C Supply Current (Low Power Mode) (Note 10) LT1815S6/LT1816A, 40kΩ Between ISET and V –, per Amplifier TA = 0°C to 70°C TA = – 40°C to 85°C LT1815S6/LT1816A TA = 0°C to 70°C TA = – 40°C to 85°C q q q q q q q q ELECTRICAL CHARACTERISTICS MIN ± 50 ± 45 ± 40 ± 50 ± 40 ± 30 ±100 ± 90 ± 70 900 750 600 150 140 130 140 130 120 35 30 25 TYP ± 80 MAX UNITS mA mA mA mA mA mA mA mA mA V/µs V/µs V/µs MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz ns ns % ns dB % Deg Ω Maximum Output Current (Low Power Mode) (Note 10) ± 75 ±200 q q q q q q ISC Output Short-Circuit Current SR Slew Rate 1500 FPBW GBW Full-Power Bandwidth Gain-Bandwidth Product 80 220 220 55 q q –3dB BW –3dB Bandwidth tr, tf tPD OS tS THD dG dP ROUT IS Rise Time, Fall Time Propagation Delay Overshoot Settling Time Total Harmonic Distortion Differential Gain Differential Phase Output Resistance Supply Current 350 1 1.4 25 15 – 70 0.08 0.04 0.20 6.5 7 9 10 7.8 10.5 11.5 1.5 1.8 2.0 mA mA mA mA mA mA mA mA mA µA µA µA 6.5 q q 1 q q q q ISET ISET Pin Current (Note 10) –150 –175 –200 – 100 181567fa 4 LT1815 LT1816/LT1817 The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C (Note 8). VS = 5V, 0V; VCM = 2.5V, RL to 2.5V unless otherwise noted. For the programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V – through 75Ω or less, unless otherwise noted. SYMBOL PARAMETER VOS Input Offset Voltage CONDITIONS (Note 4) TA = 0°C to 70°C TA = – 40°C to 85°C LT1815S6/LT1816A, 40kΩ Between ISET and V – TA = 0°C to 70°C TA = – 40°C to 85°C TA = 0°C to 70°C (Note 7) TA = – 40°C to 85°C (Note 7) TA = 0°C to 70°C TA = – 40°C to 85°C TA = 0°C to 70°C TA = – 40°C to 85°C f = 10kHz f = 10kHz VCM = 1.5V to 3.5V Differential Guaranteed by CMRR TA = – 40°C to 85°C Guaranteed by CMRR TA = – 40°C to 85°C VCM = 1.5V to 3.5V TA = 0°C to 70°C TA = – 40°C to 85°C VOUT = 1.5V to 3.5V, RL = 100Ω, LT1816/LT1817 TA = 0°C to 70°C TA = – 40°C to 85°C Guaranteed by PSRR TA = – 40°C to 85°C VOUT = 1.5V to 3.5V, RL = 500Ω TA = 0°C to 70°C TA = – 40°C to 85°C VOUT = 1.5V to 3.5V, RL = 100Ω TA = 0°C to 70°C TA = – 40°C to 85°C VOUT Maximum Output Swing (High) RL = 500Ω, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C RL = 100Ω, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C 1.5 q q ELECTRICAL CHARACTERISTICS MIN TYP 0.4 MAX 2.0 2.5 3.5 7 9 10 15 30 800 1000 1200 ±8 ± 10 ±12 UNITS mV mV mV mV mV mV µV/°C µV/°C nA nA nA µA µA µA nV/√Hz pA/√Hz MΩ kΩ pF V V Input Offset Voltage (Low Power Mode) (Note 10) ∆VOS ∆T IOS Input Offset Voltage Drift Input Offset Current 2 q q q q q q 10 10 60 IB Input Bias Current – 2.4 q q en in RIN CIN VCM Input Noise Voltage Density Input Noise Current Density Input Resistance Input Capacitance Input Voltage Range (High) Input Voltage Range (Low) 6 1.3 5 750 2 q q q q q q q q q q q q q q q 3.5 3.5 4.1 0.9 1.5 1.5 V V dB dB dB dB dB dB CMRR Common Mode Rejection Ratio 73 71 70 81 80 79 82 Channel Separation 100 Minimum Supply Voltage AVOL Large-Signal Voltage Gain 2.5 1.0 0.7 0.6 0.7 0.5 0.4 3.9 3.8 3.7 3.7 3.6 3.5 2 4 4 V V V/mV V/mV V/mV V/mV V/mV V/mV V V V V V V 1.5 4.2 4 181567fa 5 LT1815 LT1816/LT1817 The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C (Note 8). VS = 5V, 0V; VCM = 2.5V, RL to 2.5V unless otherwise noted. For the programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V – through 75Ω or less, unless otherwise noted. SYMBOL PARAMETER VOUT Maximum Output Swing (Low) CONDITIONS RL = 500Ω, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C RL = 100Ω, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C IOUT Maximum Output Current VOUT = 1.5V or 3.5V, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C LT1815S6/LT1816A; 40kΩ Between ISET and V – ; VOUT = 1.5V or 3.5V, 30mV Overdrive TA = 0°C to 70°C TA = – 40°C to 85°C VOUT = 2.5V, 1V Overdrive (Note 3) TA = 0°C to 70°C TA = – 40°C to 85°C AV = – 1 (Note 5) TA = 0°C to 70°C TA = – 40°C to 85°C 2VP-P (Note 6) f = 200kHz, RL = 500Ω, LT1815 TA = 0°C to 70°C TA = – 40°C to 85°C f = 200kHz, RL = 500Ω, LT1816/LT1817 TA = 0°C to 70°C TA = – 40°C to 85°C Gain-Bandwidth Product (Low Power Mode) (Note 10) LT1815S6/LT1816A; 40kΩ Between ISET and V – ; f = 200kHz, RL = 500Ω TA = 0°C to 70°C TA = – 40°C to 85°C AV = 1, RL = 500Ω AV = 1, 10% to 90%, 0.1V, RL = 100Ω AV = 1, 50% to 50%, 0.1V, RL = 100Ω AV = 1, 0.1V; RL = 100Ω AV = – 1, 0.1%, 2V AV = 2, f = 5MHz, VOUT = 2VP-P, RL = 500Ω AV = 2, VOUT = 2VP-P, RL = 150Ω AV = 2, VOUT = 2VP-P, RL = 150Ω AV = 1, f = 1MHz LT1815 TA = 0°C to 70°C TA = – 40°C to 85°C LT1816/LT1817, per Amplifier TA = 0°C to 70°C TA = – 40°C to 85°C Supply Current (Low Power Mode) (Note 10) LT1815S6/LT1816A, 40kΩ Between ISET and V –, per Amplifier TA = 0°C to 70°C TA = – 40°C to 85°C q q q q q q q q ELECTRICAL CHARACTERISTICS MIN TYP 0.8 MAX 1.1 1.2 1.3 1.3 1.4 1.5 UNITS V V V V V V mA mA mA mA mA mA mA mA mA V/µs V/µs V/µs MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz ns ns % ns dB % Deg Ω 1 q q q q ± 30 ± 25 ± 20 ± 30 ± 25 ± 20 ± 80 ± 70 ± 50 450 375 300 140 130 120 130 110 100 30 25 20 ± 50 Maximum Output Current (Low Power Mode) (Note 10) ± 50 ±140 q q q q q q ISC Output Short-Circuit Current SR Slew Rate 750 FPBW GBW Full-Power Bandwidth Gain-Bandwidth Product 120 200 200 50 q q –3dB BW –3dB Bandwidth tr, tf tPD OS tS THD dG dP ROUT IS Rise Time, Fall Time Propagation Delay Overshoot Settling Time Total Harmonic Distortion Differential Gain Differential Phase Output Resistance Supply Current 300 1.2 1.5 25 15 – 65 0.08 0.13 0.24 6.3 8 10 11 9 12 13 1.5 1.8 2.0 mA mA mA mA mA mA mA mA mA 181567fa 6.3 q q 0.9 q q 6 LT1815 LT1816/LT1817 ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER ISET ISET Pin Current (Note 10) The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C (Note 8). VS = 5V, 0V; VCM = 2.5V, RL to 2.5V unless otherwise noted. For the programmable current option (LT1815S6 or LT1816A), the ISET pin must be connected to V – through 75Ω or less, unless otherwise noted. CONDITIONS LT1815S6/LT1816A TA = 0°C to 70°C TA = – 40°C to 85°C q q MIN –150 –175 –200 TYP – 100 MAX UNITS µA µA µA Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: Differential inputs of ± 6V are appropriate for transient operation only, such as during slewing. Large sustained differential inputs can cause excessive power dissipation and may damage the part. Note 3: A heat sink may be required to keep the junction temperature below absolute maximum when the output is shorted indefinitely. Note 4: Input offset voltage is pulse tested and is exclusive of warm-up drift. Note 5: Slew rate is measured between ± 2V at the output with ± 3V input for ± 5V supplies and 2VP-P at the output with a 3VP-P input for single 5V supplies. Note 6: Full-power bandwidth is calculated from the slew rate: FPBW = SR/2πVP. Note 7: This parameter is not 100% tested. Note 8: The LT1815C/LT1816C/LT1817C are guaranteed to meet specified performance from 0°C to 70°C and are designed, characterized and expected to meet the extended temperature limits, but are not tested at – 40°C and 85°C. The LT1815I/LT1816I/LT1817I are guaranteed to meet the extended temperature limits. Note 9: Thermal resistance (θJA) varies with the amount of PC board metal connected to the package. The specified values are for short traces connected to the leads. If desired, the thermal resistance can be substantially reduced by connecting Pin 2 of the SOT-23, Pin 4 of the SO-8 and MS8, Pin 5 of the MS10 or the underside metal of the DD package to a large metal area. Note 10: A resistor of 40k or less is required between the ISET and V – pins of the LT1815S6 and the LT1816AMS. See the applications section for information on selecting a suitable resistor. TYPICAL PERFOR A CE CHARACTERISTICS Supply Current vs Temperature 12 PER AMPLIFIER 10 V+ – 0.5 INPUT COMMON MODE RANGE (V) INPUT BIAS CURRENT (µA) SUPPLY CURRENT (mA) 8 VS = ± 5V 6 4 2 0 –50 –25 VS = ± 2.5V 50 25 0 75 TEMPERATURE (°C) UW 100 181567 G01 Input Common Mode Range vs Supply Voltage TA = 25°C ∆VOS < 1mV 0 Input Bias Current vs Common Mode Voltage TA = 25°C VS = ± 5V –1.0 –1.5 – 2.0 –1 –2 2.0 1.5 1.0 0.5 V– –3 125 0 1 4 3 2 5 SUPPLY VOLTAGE (± V) 6 7 –4 – 5.0 0 2.5 – 2.5 INPUT COMMON MODE VOLTAGE (V) 5.0 181567 G02 181567 G03 181567fa 7 LT1815 LT1816/LT1817 TYPICAL PERFOR A CE CHARACTERISTICS Input Bias Current vs Temperature 0 INPUT VOLTAGE NOISE (nV/√Hz) –0.4 INPUT BIAS CURRENT (µA) –0.8 –1.2 –1.6 –2.0 –2.4 –2.8 –50 –25 VS = ± 5V VS = ± 2.5V OPEN-LOOP GAIN (dB) 50 25 75 0 TEMPERATURE (°C) Open-Loop Gain vs Temperature 75.0 72.5 OPEN-LOOP GAIN (dB) VS = ± 5V VO = ± 3V OUTPUT VOLTAGE SWING (V) 70.0 67.5 65.0 62.5 60.0 –50 –25 RL = 500Ω –1.5 – 2.0 RL = 100Ω OUTPUT VOLTAGE SWING (V) RL = 100Ω 50 25 75 0 TEMPERATURE (°C) Output Short-Circuit Current vs Temperature 240 OUTPUT SHORT-CIRCUIT CURRENT (mA) VS = ± 5V VIN = ± 1V SOURCE 125 200 160 120 80 40 0 –50 –25 OUTUPT CURRENT (mA) SINK 100 75 SINK, VS = ± 5V SOURCE, VS = ±2.5V OUTPUT IMPEDANCE (Ω) 50 25 75 0 TEMPERATURE (°C) 8 UW 100 181567 G04 Input Noise Spectral Density 100 TA = 25°C VS = ± 5V AV = 101 RS = 10k in 10 en 1 10 INPUT CURRENT NOISE (pA/√Hz) 75.0 72.5 70.0 Open-Loop Gain vs Resistive Load TA = 25°C VS = ± 5V 67.5 VS = ± 2.5V 65.0 62.5 60 100 1 125 10 100 1k 10k FREQUENCY (Hz) 0.1 100k 181567 G05 1k LOAD RESISTANCE (Ω) 10k 181567 G06 Output Voltage Swing vs Supply Voltage TA = 25°C – 0.5 ∆VOS = 30mV –1.0 V+ RL = 500Ω Output Voltage Swing vs Load Current TA = 25°C VS = ± 5V ∆VOS = 30mV SOURCE 5 OUTPUT VOLTAGE SWING (V) 4 –2 SINK 3 2.0 1.5 1.0 0.5 V– RL = 500Ω 0 1 4 3 2 5 SUPPLY VOLTAGE (± V) 6 7 RL = 100Ω –3 2 –4 100 125 –5 –120 –80 0 40 80 –40 OUTPUT CURRENT (mA) 120 181567 G09 181567 G07 181567 G08 Output Current vs Temperature 150 Output Impedance vs Frequency 100 SOURCE, VS = ± 5V 10 AV = 100 AV = 10 1 SINK, VS = ± 2.5V 50 25 ∆VOS = 30mV VOUT = ± 3V FOR VS = ± 5V VOUT = ± 1V FOR VS = ± 2.5V 50 25 75 0 TEMPERATURE (˚C) 100 125 0.1 AV = 1 TA = 25°C VS = ± 5V 100k 1M 10M FREQUENCY (Hz) 100M 181567 G12 100 125 0 –50 –25 0.01 10k 181567 G10 181567 G11 181567fa LT1815 LT1816/LT1817 TYPICAL PERFOR A CE CHARACTERISTICS Gain and Phase vs Frequency 80 70 60 50 GAIN ± 5V ± 2.5V 180 160 140 GAIN BANDWIDTH (MHz) GAIN (dB) 30 20 10 180 40 20 0 100M –20 500M PHASE MARGIN VS = ± 5V PHASE MARGIN VS = ± 2.5V 40 GAIN (dB) 40 100 PHASE 80 ± 2.5V ± 5V 60 TA = 25°C –10 AV = –1 RF = RG = 500Ω –20 100k 1M 10M 10k FREQUENCY (Hz) 0 Gain vs Frequency, AV = 2 10 RL = 500Ω 5 RL = 100Ω GAIN (dB) GAIN BANDWIDTH (MHz) 5 GAIN (dB) 0 TA = 25°C –5 A = 2 V VS = ± 5V RF = RG = 500Ω CF = 1pF –10 1M 10M FREQUENCY (Hz) Power Supply Rejection Ratio vs Frequency 100 POWER SUPPLY REJECTION RATIO (dB) 80 +PSRR 60 –PSRR COMMON MODE REJECTION RATIO (dB) 40 20 0 1k 10k 1M 100k FREQUENCY (Hz) 10M 100M UW 181567 G13 Gain Bandwidth and Phase Margin vs Temperature 240 RL = 500Ω 5 Gain vs Frequency, AV = 1 TA = 25°C AV = 1 VS = ± 5V RL = 500Ω GBW VS = ± 5V GBW VS = ± 2.5V PHASE MARGIN (DEG) 220 PHASE (DEG) 120 0 RL = 100Ω 200 –5 38 –50 –25 50 25 0 75 TEMPERATURE (°C) 100 36 125 –10 1M 10M 100M FREQUENCY (Hz) 500M 181567 G16 181567 G15 Gain vs Frequency, AV = – 1 240 RL = 500Ω 0 RL = 100Ω Gain Bandwidth and Phase Margin vs Supply Voltage TA = 25°C 220 200 180 160 PHASE MARGIN RL = 100Ω 40 PHASE MARGIN RL = 500Ω GBW RL = 100Ω 45 GBW RL = 500Ω PHASE MARGIN (DEG) –5 100M 300M –10 1M TA = 25°C AV = –1 VS = ± 5V RF = RG = 500Ω CF = 1pF 10M FREQUENCY (Hz) 100M 300M 35 7 0 1 5 4 3 SUPPLY VOLTAGE (± V) 2 6 181567 G17 181567 G18 181567 G19 Common Mode Rejection Ratio vs Frequency 100 TA = 25°C VS = ± 5V TA = 25°C AV = 1 VS = ± 5V 80 60 40 20 0 1k 10k 1M 100k FREQUENCY (Hz) 10M 100M 181567 G20 181567 G21 181567fa 9 LT1815 LT1816/LT1817 TYPICAL PERFOR A CE CHARACTERISTICS Supply Current vs Programming Resistor 7 6 VS = ± 5V TA = 25°C PER AMPLIFIER 250 GAIN BANDWIDTH (MHz) SUPPLY CURRENT (mA) 4 3 2 1 0 10 100 1k 10k RSET PROGRAMMING RESISTOR (Ω) 40k 150 RL = 100Ω 100 SLEW RATE (V/µs) 5 Slew Rate vs Supply Voltage 1200 TA =25°C AV = – 1 VIN = 2VP-P 1000 RF = RG = RL = 500Ω VS = ± 5V SR VS = ± 5V – DIFFERENTIAL PHASE (DEG) SLEW RATE (V/µs) SLEW RATE (V/µs) 800 SR + SR – 600 400 0 1 4 3 2 5 SUPPLY VOLTAGE (± V) 6 7 Distortion vs Frequency, AV = 2 –30 –40 –50 –60 –70 –80 –90 –100 100k 2ND HARMONIC 3RD HARMONIC AV = 2 VS = ± 5V VO = 2VP-P RL = 100Ω DISTORTION (dB) –30 –40 –50 –60 –70 –80 –90 DISTORTION (dB) DISTORTION (dB) 1M FREQUENCY (Hz) 10 UW 181567 F03 181567 G23 Gain Bandwidth Product vs Programming Resistor VS = ± 5V TA = 25°C RL = 500Ω 1800 Slew Rate vs Input Step TA =25°C AV = – 1 V = ± 5V 1500 RS = R = R = 500Ω F G L 1200 200 SR + SR – 900 50 600 0 10 100 1k 10k RSET PROGRAMING RESISTOR (Ω) 40k 300 0 1 2 4 3 5 6 INPUT STEP (VP-P) 7 8 181567 F02 181567 G24 Slew Rate vs Temperature 2400 2000 1600 1200 800 400 AV = –1 RF = RG = RL = 500Ω (NOTE 5) SR – VS = ± 2.5V SR+ Differential Gain and Phase vs Supply Voltage TA = 25°C DIFFERENTIAL GAIN RL = 150Ω 0.10 0.08 DIFFERENTIAL GAIN (%) 0.06 0.12 0.10 0.08 0.06 0.04 0.02 0 DIFFERENTIAL PHASE RL = 150Ω 0.04 0.02 0 SR + VS = ± 2.5V 0 –50 –25 50 25 75 0 TEMPERATURE (°C) 100 125 4 8 6 10 TOTAL SUPPLY VOLTAGE (V) 12 181567 G26 181567 G25 Distortion vs Frequency, AV = –1 AV = –1 VS = ± 5V VO = 2VP-P RL = 100Ω –30 –40 –50 –60 –70 –80 –90 Distortion vs Frequency, AV = 1 AV = 1 VS = ± 5V VO = 2VP-P RL = 100Ω 2ND HARMONIC 3RD HARMONIC 2ND HARMONIC 3RD HARMONIC 10M 181567 G28 –100 100k 1M FREQUENCY (Hz) 10M 181567 G29 –100 100k 1M FREQUENCY (Hz) 10M 181567 G30 181567fa LT1815 LT1816/LT1817 TYPICAL PERFOR A CE CHARACTERISTICS Small-Signal Transient, AV = – 1 Small-Signal Transient, AV = 1 Large-Signal Transient, AV = – 1, VS = ±5V UW 181567 G31 181567 G32 Large-Signal Transient, AV = 1, VS = ± 5V 181567 G33 181567 G34 181567fa 11 LT1815 LT1816/LT1817 APPLICATIO S I FOR ATIO Layout and Passive Components As with all high speed amplifiers, the LT1815/LT1816/ LT1817 require some attention to board layout. A ground plane is recommended and trace lengths should be minimized, especially on the negative input lead. Low ESL/ESR bypass capacitors should be placed directly at the positive and negative supply (0.01µF ceramics are recommended). For high drive current applications, additional 1µF to 10µF tantalums should be added. The parallel combination of the feedback resistor and gain setting resistor on the inverting input combine with the input capacitance to form a pole that can cause peaking or even oscillations. If feedback resistors greater than 1k are used, a parallel capacitor of value: CF > RG • CIN/RF should be used to cancel the input pole and optimize dynamic performance. For applications where the DC noise gain is 1 and a large feedback resistor is used, CF should be greater than or equal to CIN. An example would be an I-to-V converter. Input Considerations The inputs of the LT1815/LT1816/LT1817 amplifiers are connected to the base of an NPN and PNP bipolar transistor in parallel. The base currents are of opposite polarity and provide first-order bias current cancellation. Due to variation in the matching of NPN and PNP beta, the polarity of the input bias current can be positive or negative. The offset current, however, does not depend on beta matching and is tightly controlled. Therefore, the use of balanced source resistance at each input is recommended for applications where DC accuracy must be maximized. For example, with a 100Ω source resistance at each input, the 800nA maximum offset current results in only 80µV of extra offset, while without balance the 8 µA maximum input bias current could result in a 0.8mV offset contribution. The inputs can withstand differential input voltages of up to 6V without damage and without needing clamping or series resistance for protection. This differential input voltage generates a large internal current (up to 80mA), 12 U which results in the high slew rate. In normal transient closed-loop operation, this does not increase power dissipation significantly because of the low duty cycle of the transient inputs. Sustained differential inputs, however, will result in excessive power dissipation and therefore this device should not be used as a comparator . Capacitive Loading The LT1815/LT1816/LT1817 are optimized for high bandwidth and low distortion applications. They can drive a capacitive load of 10pF in a unity-gain configuration and more with higher gain. When driving a larger capacitive load, a resistor of 10Ω to 50Ω should be connected between the output and the capacitive load to avoid ringing or oscillation. The feedback should still be taken from the output so that the resistor will isolate the capacitive load to ensure stability. Slew Rate The slew rate of the LT1815/LT1816/LT1817 is proportional to the differential input voltage. Therefore, highest slew rates are seen in the lowest gain configurations. For example, a 5V output step in a gain of 10 has a 0.5V input step, whereas in unity gain there is a 5V input step. The LT1815/LT1816/ LT1817 are tested for a slew rate in a gain of – 1. Lower slew rates occur in higher gain configurations. Programmable Supply Current (LT1815/LT1816A) In order to operate the LT1815S6 or LT1816A at full speed (and full supply current), connect the ISET pin to the negative supply through a resistance of 75Ω or less. To adjust or program the supply current and speed of the LT1815S6 or LT1816A, connect an external resistor (RSET) between the ISET pin and the negative supply as shown in Figure 1. The amplifiers are fully functional with 0 ≤ RSET ≤ 40k. Figures 2 and 3 show how the gain bandwidth and supply current vary with the value of the programming resistor RSET. In addition, the Electrical Characteristics section of the data sheet specifies maximum supply current and offset voltage, as well as minimum gain bandwidth and output current at the maximum R SET value of 40k. 181567fa W UU LT1815 LT1816/LT1817 APPLICATIO S I FOR ATIO 5V – LT1815S6 V + + ISET RSET V– 181567 F01 –5V Figure 1. Programming Resistor Between ISET and V – 250 VS = ± 5V TA = 25°C RL = 500Ω 200 GAIN BANDWIDTH (MHz) 150 RL = 100Ω 100 50 0 10 100 1k 10k RSET PROGRAMING RESISTOR (Ω) 40k 181567 F02 Figure 2. Gain Bandwidth Product vs RSET Programming Resistor 7 6 SUPPLY CURRENT (mA) VS = ±5V TA = 25°C PER AMPLIFIER 5 4 3 2 1 0 10 100 1k 10k RSET PROGRAMMING RESISTOR (Ω) 40k 181567 F03 Figure 3. Supply Current vs RSET Programming Resistor U Power Dissipation The LT1815/LT1816/LT1817 combine high speed and large output drive in small packages. It is possible to exceed the maximum junction temperature specification (150°C) under certain conditions. Maximum junction temperature (TJ) is calculated from the ambient temperature (TA), power dissipation per amplifier (PD) and number of amplifiers (n) as follows: TJ = TA + (n • PD • θJA) Power dissipation is composed of two parts. The first is due to the quiescent supply current and the second is due to on-chip dissipation caused by the load current. The worstcase load induced power occurs when the output voltage is at 1/2 of either supply voltage (or the maximum swing if less than 1/2 the supply voltage). Therefore PDMAX is: PDMAX = (V+ – V –) • (ISMAX) + (V+/2)2/RL or PDMAX = (V+ – V –) • (ISMAX) + (V+ – VOMAX) • (VOMAX/RL) Example: LT1816IS8 at 85°C, VS = ± 5V, RL=100Ω PDMAX = (10V) • (11.5mA) + (2.5V)2/100Ω = 178mW TJMAX = 85°C + (2 • 178mW) • (150°C/W) = 138°C Circuit Operation The LT1815/LT1816/LT1817 circuit topology is a true voltage feedback amplifier that has the slewing behavior of a current feedback amplifier. The operation of the circuit can be understood by referring to the Simplified Schematic. Complementary NPN and PNP emitter followers buffer the inputs and drive an internal resistor. The input voltage appears across the resistor, generating current that is mirrored into the high impedance node. Complementary followers form an output stage that buffers the gain node from the load. The input resistor, input stage transconductance and the capacitor on the high impedance node determine the bandwidth. The slew rate is determined by the current available to charge the gain node capacitance. This current is the differential input voltage divided by R1, so the slew rate is proportional to the input step. Highest slew rates are therefore seen in the lowest gain configurations. 181567fa W UU 13 LT1815 LT1816/LT1817 SI PLIFIED SCHE ATIC V+ BIAS CONTROL R1 –IN C +IN OUT ISET V– 181567 SS LT1815S6/LT1816AMS ONLY TYPICAL APPLICATIO S Two Op Amp Instrumentation Amplifier R5 220Ω R1 10k R2 1k R4 10k VIN  R4    1   R2 R3  R2 + R3 GAIN =   1 +    + + R5    R3    2   R1 R4   TRIM R5 FOR GAIN TRIM R1 FOR COMMON MODE REJECTION BW = 2MHz 14 U W W (one amplifier) – 1/2 LT1816 R3 1k – 1/2 LT1816 VOUT – + + + ( )  = 102    181567 TA03 181567fa LT1815 LT1816/LT1817 TYPICAL APPLICATIO S Photodiode Transimpedance Amplifier 1pF 1pF PHOTODIODE SIEMENS/ INFINEON SFH213 VIN 220pF 1/2 LT1816 470pF + – + – 232Ω U 4.75k 5V – LT1815 + – 5V – 5V 4.75k 0.01µF OUTPUT OFFSET ≤1mV TYPICAL BANDWIDTH = 30MHz 10% TO 90% RISE TIME = 22ns OUTPUT NOISE (20MHz BW) = 300µVP-P 181567 TA04 4MHz, 4th Order Butterworth Filter 232Ω 47pF 274Ω 22pF 665Ω 274Ω 562Ω 1/2 LT1816 VOUT 181567 TA05 181567fa 15 LT1815 LT1816/LT1817 PACKAGE DESCRIPTIO 0.62 MAX 3.85 MAX 2.62 REF RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.20 BSC 0.90 – 1.45 DATUM ‘A’ 0.35 – 0.55 REF 0.09 – 0.20 NOTE: (NOTE 3) 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ) 0.62 MAX 3.85 MAX 2.62 REF RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.20 BSC 0.90 – 1.45 DATUM ‘A’ 0.35 – 0.55 REF 0.09 – 0.20 NOTE: (NOTE 3) 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ) 16 U S5 Package 5-Lead Plastic SOT-23 (Reference LTC DWG # 05-08-1633) (Reference LTC DWG # 05-08-1635) 0.95 REF 2.80 – 3.10 (NOTE 4) 1.22 REF 1.4 MIN 2.60 – 3.00 1.50 – 1.75 (NOTE 4) PIN ONE 0.25 – 0.50 TYP 5 PLCS NOTE 3 0.95 BSC 0.90 – 1.30 0.00 – 0.15 1.90 BSC S5 SOT-23 0502 ATTENTION: ORIGINAL SOT23-5L PACKAGE. MOST SOT23-5L PRODUCTS CONVERTED TO THIN SOT23 PACKAGE, DRAWING # 05-08-1635 AFTER APPROXIMATELY APRIL 2001 SHIP DATE S6 Package 6-Lead Plastic SOT-23 (Reference LTC DWG # 05-08-1634) (Reference LTC DWG # 05-08-1636) 0.95 REF 2.80 – 3.10 (NOTE 4) 1.22 REF 1.4 MIN 2.60 – 3.00 1.50 – 1.75 (NOTE 4) PIN ONE ID 0.95 BSC 0.90 – 1.30 0.25 – 0.50 TYP 6 PLCS NOTE 3 1.90 BSC 0.09 – 0.15 NOTE 3 S6 SOT-23 0502 ATTENTION: ORIGINAL SOT23-6L PACKAGE. MOST SOT23-6L PRODUCTS CONVERTED TO THIN SOT23 PACKAGE, DRAWING # 05-08-1636 AFTER APPROXIMATELY APRIL 2001 SHIP DATE 181567fa LT1815 LT1816/LT1817 PACKAGE DESCRIPTIO 3.5 ± 0.05 1.65 ± 0.05 2.15 ± 0.05 (2 SIDES) PACKAGE OUTLINE 0.28 ± 0.05 0.50 BSC 2.38 ± 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 5.23 (.206) MIN 0.42 ± 0.04 (.0165 ± .0015) TYP RECOMMENDED SOLDER PAD LAYOUT DETAIL “A” 0° – 6° TYP 4.90 ± 0.15 (1.93 ± .006) 3.00 ± 0.102 (.118 ± .004) NOTE 4 GAUGE PLANE 0.53 ± 0.015 (.021 ± .006) DETAIL “A” 0.18 (.077) SEATING PLANE 0.22 – 0.38 (.009 – .015) TYP 0.13 ± 0.076 (.005 ± .003) MSOP (MS8) 0802 NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX U DD Package 8-Lead Plastic DFN (3mm × 3mm) (Reference LTC DWG # 05-08-1698) R = 0.115 TYP 5 0.675 ± 0.05 0.38 ± 0.10 8 3.00 ± 0.10 (4 SIDES) PIN 1 TOP MARK (DD8) DFN 0203 1.65 ± 0.10 (2 SIDES) 0.200 REF 0.75 ± 0.05 4 0.28 ± 0.05 2.38 ± 0.10 (2 SIDES) 1 0.50 BSC 0.00 – 0.05 BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 4. EXPOSED PAD SHALL BE SOLDER PLATED MS8 Package 8-Lead Plastic MSOP (Reference LTC DWG # 05-08-1660) 0.889 ± 0.127 (.035 ± .005) 3.2 – 3.45 (.126 – .136) 0.65 (.0256) BSC 3.00 ± 0.102 (.118 ± .004) (NOTE 3) 8 7 65 0.52 (.206) REF 0.254 (.010) 1 1.10 (.043) MAX 23 4 0.86 (.034) REF 0.65 (.0256) BSC 181567fa 17 LT1815 LT1816/LT1817 PACKAGE DESCRIPTIO 5.23 (.206) MIN 0.50 0.305 ± 0.038 (.0197) (.0120 ± .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT GAUGE PLANE 12345 0.53 ± 0.01 (.021 ± .006) DETAIL “A” 0.18 (.007) SEATING PLANE 0.17 – 0.27 (.007 – .011) TYP 0.13 ± 0.076 (.005 ± .003) MSOP (MS) 0802 NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX .050 BSC 8 N N .245 MIN .160 ±.005 .228 – .244 (5.791 – 6.197) 1 .030 ±.005 TYP 2 3 N/2 RECOMMENDED SOLDER PAD LAYOUT .010 – .020 × 45° (0.254 – 0.508) .008 – .010 (0.203 – 0.254) 0°– 8° TYP NOTE: 1. DIMENSIONS IN INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) 18 U MS10 Package 10-Lead Plastic MSOP (Reference LTC DWG # 05-08-1661) 0.889 ± 0.127 (.035 ± .005) 3.2 – 3.45 (.126 – .136) 3.00 ± 0.102 (.118 ± .004) (NOTE 3) 10 9 8 7 6 0.497 ± 0.076 (.0196 ± .003) REF 0.254 (.010) DETAIL “A” 0° – 6° TYP 4.90 ± 0.15 (1.93 ± .006) 3.00 ± 0.102 (.118 ± .004) NOTE 4 1.10 (.043) MAX 0.86 (.034) REF 0.50 (.0197) BSC S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch) (Reference LTC DWG # 05-08-1610) .189 – .197 (4.801 – 5.004) NOTE 3 7 6 5 .045 ±.005 .150 – .157 (3.810 – 3.988) NOTE 3 N/2 1 2 3 4 .053 – .069 (1.346 – 1.752) .004 – .010 (0.101 – 0.254) .016 – .050 (0.406 – 1.270) .014 – .019 (0.355 – 0.483) TYP .050 (1.270) BSC SO8 0502 181567fa LT1815 LT1816/LT1817 PACKAGE DESCRIPTIO S Package 14-Lead Plastic Small Outline (Narrow .150 Inch) (Reference LTC DWG # 05-08-1610) .045 ±.005 .050 BSC N 14 13 .337 – .344 (8.560 – 8.738) NOTE 3 12 11 10 9 8 .245 MIN 1 .030 ±.005 TYP 2 3 RECOMMENDED SOLDER PAD LAYOUT 1 .010 – .020 × 45° (0.254 – 0.508) 2 3 4 5 6 7 .008 – .010 (0.203 – 0.254) .016 – .050 (0.406 – 1.270) NOTE: 1. DIMENSIONS IN INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) .254 MIN .0165 ± .0015 RECOMMENDED SOLDER PAD LAYOUT 1 .015 ± .004 × 45° (0.38 ± 0.10) .007 – .0098 (0.178 – 0.249) .016 – .050 (0.406 – 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 0° – 8° TYP .053 – .068 (1.351 – 1.727) 23 4 56 7 8 .004 – .0098 (0.102 – 0.249) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U N .160 ±.005 .228 – .244 (5.791 – 6.197) N/2 N/2 .150 – .157 (3.810 – 3.988) NOTE 3 .053 – .069 (1.346 – 1.752) 0° – 8° TYP .004 – .010 (0.101 – 0.254) .014 – .019 (0.355 – 0.483) TYP .050 (1.270) BSC S14 0502 GN Package 16-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .045 ± .005 .189 – .196* (4.801 – 4.978) 16 15 14 13 12 11 10 9 .009 (0.229) REF .150 – .165 .229 – .244 (5.817 – 6.198) .150 – .157** (3.810 – 3.988) .0250 TYP .008 – .012 (0.203 – 0.305) .0250 (0.635) BSC GN16 (SSOP) 0502 181567fa 19 LT1815 LT1816/LT1817 TYPICAL APPLICATIO S Bandpass Filter with Independently Settable Gain, Q and fC R1 0 VIN 1/4 LT1817 1/4 LT1817 GAIN = R1 RG Q = R1 RQ fC = 1 2πRFC R C 1/4 LT1817 Differential DSL Receiver 5V V+ + DRIVER – DRIVER PHONE LINE RELATED PARTS PART NUMBER LT1363/LT1364/LT1365 LT1395/LT1396/LT1397 LT1806/LT1807 LT1809/LT1810 LT1812/LT1813/LT1814 DESCRIPTION Single/Dual/Quad 70MHz, 1V/ns, C-Load Op Amp Single/Dual/Quad 400MHz Current Feedback Amplifier Single/Dual 325MHz, 140V/µs Rail-to-Rail I/O Op Amp Single/Dual 180MHz, 350V/µs Rail-to-Rail I/O Op Amp Single/Dual/Quad 3mA, 100MHz, 750V/µs Op Amp TM C-Load is a trademark of Linear Technology Corporation. 181567fa 20 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 q FAX: (408) 434-0507 q www.linear.com + – – + + – + – RG RQ R C RF 1/4 LT1817 BANDPASS OUT RF OUTPUT MAGNITUDE (6dB/DIV) U 455kHz Filter Frequency Response R = 499Ω R1 = 499Ω RF = 511Ω RQ = 49.9Ω RG = 499Ω C = 680pF fC = 455kHz Q = 10 GAIN = 1 VS = ±5V VIN = 5VP-P DISTORTION: 2nd < –76dB 3rd < –90dB ACROSS FREQ RANGE NOISE: ≈ 60µV OVER 1MHz BANDWIDTH R 100k 1M FREQUENCY (Hz) 10M 181567 TA06b 181567 TA06a + 1/2 LT1816 – DIFFERENTIAL RECEIVE SIGNAL – 1/2 LT1816 + V– –5V 181567 TA07 COMMENTS Wide Supply Range: ± 2.5V to ±15V 4.6mA Supply Current, 800V/µs, 80mA Output Current Low Noise: 3.5nV/√Hz Low Distortion: 90dBc at 5MHz Low Power: 3.6mA Max at ± 5V LT/TP 0303 1K REV A • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2001