LT3092

FeaTures n n n n n n n n LT3060 Series 45V VIN , Micropower, Low Noise, 100mA Low Dropout, Linear Regulator DescripTion The LT®3060 series are micropower, low dropout voltage (LDO) linear regulators that operate over a 1.6V to 45V input supply range. The devices supply 100mA of output current with a typical dropout voltage of 300mV. A single external capacitor provides programmable low noise reference performance and output soft-start functionality. The LT3060’s quiescent current is merely 40μA and provides fast transient response with a minimum 2.2μF output capacitor. In shutdown, quiescent current is less than 1μA and the reference soft-start capacitor is reset. The LT3060 regulators optimize stability and transient response with low ESR, ceramic output capacitors. The regulators do not require the addition of ESR as is common with other regulators. Internal protection circuitry includes reverse-battery protection, reverse-output protection, reverse-current protection, current limit with foldback and thermal shutdown. The LT3060 series are available in fixed output voltages of 1.2V, 1.5V, 1.8V, 2.5V, 3.3V and 5V, and as an adjustable voltage regulator with an output voltage range from the 600mV reference to 44.5V. The LT3060 regulators are offered in the thermally enhanced 8-lead TSOT-23 and 8-lead (2mm × 2mm × 0.75mm) DFN packages. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. n n n n n n Input Voltage Range: 1.6V to 45V Output Current: 100mA Quiescent Current: 40µA Dropout Voltage: 300mV Low Noise: 30µVRMS (10Hz to 100kHz) Adjustable Output: VREF = 600mV Fixed Output Voltages: 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5V Output Tolerance: ±2% Over Line, Load and Temperature Single Capacitor Soft-Starts Reference and Lowers Output Noise Shutdown Current: < 1µA Reverse Battery Protection Current Limit Foldback Protection Thermal Limit Protection 8-Lead 2mm × 2mm × 0.75mm DFN and 8-Lead ThinSOT ™ Packages Battery-Powered Systems Automotive Power Supplies Industrial Power Supplies Avionic Power Supplies Portable Instruments applicaTions n n n n n Typical applicaTion 2.5V Low Noise Regulator DROPOUT VOLTAGE (mV) IN VIN 3V TO 45V 1µF OUT LT3060-2.5 SHDN ADJ CFF 10nF VOUT 2.5V AT 100mA 30µVRMS NOISE 10µF 350 300 250 200 150 100 50 3060 TA01 Dropout Voltage TJ = 25°C GND REF/BYP 10nF 0 0 10 20 30 40 50 60 70 80 90 100 OUTPUT CURRENT (mA) 3060 TA02 3060fa 1 LT3060 Series absoluTe MaxiMuM raTings (Note 1) IN Pin Voltage ........................................................ ±50V OUT Pin Voltage ..................................................... ± 50V Input-to-Output Differential Voltage (Note 2) ......... ±50V ADJ Pin Voltage ..................................................... ±50V SHDN Pin Voltage .................................................. ± 50V REF/BYP Pin Voltage....................................... – 0.3V, 1V Output Short-Circuit Duration .......................... Indefinite Operating Junction Temperature (Notes 3, 5, 13) E-, I-Grades .......................................– 40°C to 125°C MP-Grade .......................................... –55°C to 125°C H-Grade ............................................. – 40°C to 150°C Storage Temperature Range ..................– 65°C to 150°C Lead Temperature (TS8 Soldering, 10 sec) ........... 300°C pin conFiguraTion TOP VIEW REF/BYP 1 ADJ 2 OUT 3 OUT 4 9 GND 8 GND 7 SHDN 6 IN 5 IN TOP VIEW SHDN 1 GND 2 GND 3 GND 4 8 REF/BYP 7 ADJ 6 OUT 5 IN DC PACKAGE 8-LEAD (2mm × 2mm) PLASTIC DFN TJMAX = 125°C, θJA = 48°C/W TO 60°C/W*, θJC = 20°C/W EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB * SEE APPLICATIONS INFORMATION SECTION TS8 PACKAGE 8-LEAD PLASTIC TSOT-23 TJMAX = 150°C, θJA = 57°C/W TO 67°C/W*, θJC = 25°C/W orDer inForMaTion LEAD FREE FINISH LT3060EDC#PBF LT3060IDC#PBF LT3060EDC-1.2#PBF LT3060IDC-1.2#PBF LT3060EDC-1.5#PBF LT3060IDC-1.5#PBF LT3060EDC-1.8#PBF LT3060IDC-1.8#PBF LT3060EDC-2.5#PBF LT3060IDC-2.5#PBF LT3060EDC-3.3#PBF LT3060IDC-3.3#PBF LT3060EDC-5#PBF LT3060IDC-5#PBF LT3060ETS8#PBF LT3060ITS8#PBF TAPE AND REEL LT3060EDC#TRPBF LT3060IDC#TRPBF LT3060EDC-1.2#TRPBF LT3060IDC-1.2#TRPBF LT3060EDC-1.5#TRPBF LT3060IDC-1.5#TRPBF LT3060EDC-1.8#TRPBF LT3060IDC-1.8#TRPBF LT3060EDC-2.5#TRPBF LT3060IDC-2.5#TRPBF LT3060EDC-3.3#TRPBF LT3060IDC-3.3#TRPBF LT3060EDC-5#TRPBF LT3060IDC-5#TRPBF LT3060ETS8#TRPBF LT3060ITS8#TRPBF PART MARKING* LDTD LDTD LFVT LFVT LFVV LFVV LFVW LFVW LFVX LFVX LFVY LFVY LFVZ LFVZ LTDTF LTDTF PACKAGE DESCRIPTION 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT TEMPERATURE RANGE –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C 3060fa 2 LT3060 Series orDer inForMaTion LEAD FREE FINISH LT3060MPTS8#PBF LT3060HTS8#PBF LT3060ETS8-1.2#PBF LT3060ITS8-1.2#PBF LT3060MPTS8-1.2#PBF LT3060HTS8-1.2#PBF LT3060ETS8-1.5#PBF LT3060ITS8-1.5#PBF LT3060MPTS8-1.5#PBF LT3060HTS8-1.5#PBF LT3060ETS8-1.8#PBF LT3060ITS8-1.8#PBF LT3060MPTS8-1.8#PBF LT3060HTS8-1.8#PBF LT3060ETS8-2.5#PBF LT3060ITS8-2.5#PBF LT3060MPTS8-2.5#PBF LT3060HTS8-2.5#PBF LT3060ETS8-3.3#PBF LT3060ITS8-3.3#PBF LT3060MPTS8-3.3#PBF LT3060HTS8-3.3#PBF LT3060ETS8-5#PBF LT3060ITS8-5#PBF LT3060MPTS8-5#PBF LT3060HTS8-5#PBF LEAD BASED FINISH LT3060EDC LT3060IDC LT3060EDC-1.2 LT3060IDC-1.2 LT3060EDC-1.5 LT3060IDC-1.5 LT3060EDC-1.8 LT3060IDC-1.8 LT3060EDC-2.5 LT3060IDC-2.5 LT3060EDC-3.3 LT3060IDC-3.3 TAPE AND REEL LT3060MPTS8#TRPBF LT3060HTS8#TRPBF LT3060ETS8-1.2#TRPBF LT3060ITS8-1.2#TRPBF LT3060MPTS8-1.2#TRPBF LT3060HTS8-1.2#TRPBF LT3060ETS8-1.5#TRPBF LT3060ITS8-1.5#TRPBF LT3060MPTS8-1.5#TRPBF LT3060HTS8-1.5#TRPBF LT3060ETS8-1.8#TRPBF LT3060ITS8-1.8#TRPBF LT3060MPTS8-1.8#TRPBF LT3060HTS8-1.8#TRPBF LT3060ETS8-2.5#TRPBF LT3060ITS8-2.5#TRPBF LT3060MPTS8-2.5#TRPBF LT3060HTS8-2.5#TRPBF LT3060ETS8-3.3#TRPBF LT3060ITS8-3.3#TRPBF LT3060MPTS8-3.3#TRPBF LT3060HTS8-3.3#TRPBF LT3060ETS8-5#TRPBF LT3060ITS8-5#TRPBF LT3060MPTS8-5#TRPBF LT3060HTS8-5#TRPBF TAPE AND REEL LT3060EDC#TR LT3060IDC#TR LT3060EDC-1.2#TR LT3060IDC-1.2#TR LT3060EDC-1.5#TR LT3060IDC-1.5#TR LT3060EDC-1.8#TR LT3060IDC-1.8#TR LT3060EDC-2.5#TR LT3060IDC-2.5#TR LT3060EDC-3.3#TR LT3060IDC-3.3#TR PART MARKING* LTDTF LTDTF LTFWB LTFWB LTFWB LTFWB LTFWC LTFWC LTFWC LTFWC LTFWD LTFWD LTFWD LTFWD LTFWF LTFWF LTFWF LTFWF LTFWG LTFWG LTFWG LTFWG LTFWH LTFWH LTFWH LTFWH PART MARKING* LDTD LDTD LFVT LFVT LFVV LFVV LFVW LFVW LFVX LFVX LFVY LFVY PACKAGE DESCRIPTION 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT PACKAGE DESCRIPTION 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN TEMPERATURE RANGE –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C TEMPERATURE RANGE –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C 3060fa 3 LT3060 Series orDer inForMaTion LEAD FREE FINISH LT3060EDC-5 LT3060IDC-5 LT3060ETS8 LT3060ITS8 LT3060MPTS8 LT3060HTS8 LT3060ETS8-1.2 LT3060ITS8-1.2 LT3060MPTS8-1.2 LT3060HTS8-1.2 LT3060ETS8-1.5 LT3060ITS8-1.5 LT3060MPTS8-1.5 LT3060HTS8-1.5 LT3060ETS8-1.8 LT3060ITS8-1.8 LT3060MPTS8-1.8 LT3060HTS8-1.8 LT3060ETS8-2.5 LT3060ITS8-2.5 LT3060MPTS8-2.5 LT3060HTS8-2.5 LT3060ETS8-3.3 LT3060ITS8-3.3 LT3060MPTS8-3.3 LT3060HTS8-3.3 LT3060ETS8-5 LT3060ITS8-5 LT3060MPTS8-5 LT3060HTS8-5 TAPE AND REEL LT3060EDC-5#TR LT3060IDC-5#TR LT3060ETS8#TR LT3060ITS8#TR LT3060MPTS8#TR LT3060HTS8#TR LT3060ETS8-1.2#TR LT3060ITS8-1.2#TR LT3060MPTS8-1.2#TR LT3060HTS8-1.2#TR LT3060ETS8-1.5#TR LT3060ITS8-1.5#TR LT3060MPTS8-1.5#TR LT3060HTS8-1.5#TR LT3060ETS8-1.8#TR LT3060ITS8-1.8#TR LT3060MPTS8-1.8#TR LT3060HTS8-1.8#TR LT3060ETS8-2.5#TR LT3060ITS8-2.5#TR LT3060MPTS8-2.5#TR LT3060HTS8-2.5#TR LT3060ETS8-3.3#TR LT3060ITS8-3.3#TR LT3060MPTS8-3.3#TR LT3060HTS8-3.3#TR LT3060ETS8-5#TR LT3060ITS8-5#TR LT3060MPTS8-5#TR LT3060HTS8-5#TR PART MARKING* LFVZ LFVZ LTDTF LTDTF LTDTF LTDTF LTFWB LTFWB LTFWB LTFWB LTFWC LTFWC LTFWC LTFWC LTFWD LTFWD LTFWD LTFWD LTFWF LTFWF LTFWF LTFWF LTFWG LTFWG LTFWG LTFWG LTFWH LTFWH LTFWH LTFWH PACKAGE DESCRIPTION 8-Lead (2mm × 2mm) Plastic DFN 8-Lead (2mm × 2mm) Plastic DFN 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT 8-Lead Plastic ThinSOT TEMPERATURE RANGE –40°C to 125°C –40°C to 125°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C –40°C to 125°C –40°C to 125°C –55°C to 125°C –40°C to 150°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3060fa 4 LT3060 Series elecTrical characTerisTics PARAMETER Minimum Input Voltage (Notes 4, 12) Regulated Output Voltage (Note 5) CONDITIONS ILOAD = 100mA LT3060-1.2: VIN = 2.1V, ILOAD = 1mA 2.1V < VIN < 45V, 1mA < ILOAD < 100mA 2.1V < VIN < 45V, 1mA < ILOAD < 100mA LT3060-1.5: VIN = 2.1V, ILOAD = 1mA 2.1V < VIN < 45V, 1mA < ILOAD < 100mA 2.1V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3) MIN l TYP 1.6 1.2 1.2 1.2 1.5 1.5 1.5 1.8 1.8 1.8 2.5 2.5 2.5 3.3 3.3 3.3 5 5 5 600 600 600 0.9 1 1.1 1.2 1.3 1.5 0.6 2.4 2.5 2.6 2.8 3.1 3.7 0.2 MAX 2.1 1.212 1.224 1.224 1.515 1.530 1.530 1.818 1.836 1.836 2.525 2.550 2.550 3.333 3.366 3.366 5.050 5.100 5.100 606 612 612 3.5 7 4.2 8 4.5 12 5.4 15 7 19 8.5 25 3.5 4 10 18 12 22 14 27 19 37 24 49 35 75 4 9 UNITS V V V V V V V V V V V V V V V V V V V mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV mV 3060fa l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l 1.188 1.176 1.170 1.485 1.470 1.463 1.782 1.764 1.755 2.475 2.450 2.438 3.267 3.234 3.218 4.950 4.900 4.875 594 588 585 LT3060-1.8: VIN = 2.35V, ILOAD = 1mA 2.35V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-, MP-Grades) 2.35V < VIN < 45V, 1mA < ILOAD < 100mA (H-Grade) LT3060-2.5: VIN = 3.05V, ILOAD = 1mA 3.05V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-, MP-Grades) 3.05V < VIN < 45V, 1mA < ILOAD < 100mA (H-Grade) LT3060-3.3: VIN = 3.85V, ILOAD = 1mA 3.85V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-, MP-Grades) 3.85V < VIN < 45V, 1mA < ILOAD < 100mA (H-Grade) LT3060-5: VIN = 5.55V, ILOAD = 1mA 5.55V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-, MP-Grades) 5.55V < VIN < 45V, 1mA < ILOAD < 100mA (H-Grade) VIN = 2.1V, ILOAD = 1mA 2.1V < VIN < 45V, 1mA < ILOAD < 100mA 2.1V < VIN < 45V, 1mA < ILOAD < 100mA ΔVIN = 2.1V to 45V, ILOAD = 1mA ΔVIN = 2.1V to 45V, ILOAD = 1mA ΔVIN = 2.1V to 45V, ILOAD = 1mA ΔVIN = 2.1V to 45V, ILOAD = 1mA ΔVIN = 2.35V to 45V, ILOAD = 1mA ΔVIN = 2.35V to 45V, ILOAD = 1mA ΔVIN = 3.05V to 45V, ILOAD = 1mA ΔVIN = 3.05V to 45V, ILOAD = 1mA ΔVIN = 3.85V to 45V, ILOAD = 1mA ΔVIN = 3.85V to 45V, ILOAD = 1mA ΔVIN = 5.55V to 45V, ILOAD = 1mA ΔVIN = 5.55V to 45V, ILOAD = 1mA ΔVIN = 2.1V to 45V, ILOAD = 1mA ΔVIN = 2.1V to 45V, ILOAD = 1mA VIN = 2.1V, ILOAD = 1mA to 100mA VIN = 2.1V, ILOAD = 1mA to 100mA VIN = 2.1V, ILOAD = 1mA to 100mA VIN = 2.1V, ILOAD = 1mA to 100mA VIN = 2.35V, ILOAD = 1mA to 100mA VIN = 2.35V, ILOAD = 1mA to 100mA VIN = 3.05V, ILOAD = 1mA to 100mA VIN = 3.05V, ILOAD = 1mA to 100mA VIN = 3.85V, ILOAD = 1mA to 100mA VIN = 3.85V, ILOAD = 1mA to 100mA VIN = 5.55V, ILOAD = 1mA to 100mA VIN = 5.55V, ILOAD = 1mA to 100mA VIN = 2.1V, ILOAD = 1mA to 100mA VIN = 2.1V, ILOAD = 1mA to 100mA (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) (E-, I-, MP-Grades) (H-Grade) ADJ Pin Voltage (Notes 4, 5) Line Regulation LT3060: LT3060-1.2: LT3060-1.5: LT3060-1.8: LT3060-2.5: LT3060-3.3: LT3060-5: LT3060: (Note 4) LT3060-1.2: LT3060-1.5: LT3060-1.8: LT3060-2.5: LT3060-3.3: LT3060-5: LT3060: (Note 4) Load Regulation (Note 15) 5 LT3060 Series The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3) CONDITIONS ILOAD = 1mA ILOAD = 1mA ILOAD = 10mA ILOAD = 10mA ILOAD = 50mA (Note 14) ILOAD = 50mA (Note 14) ILOAD = 100mA (Note 14) ILOAD = 100mA (Note 14) ILOAD = 0µA GND Pin Current VIN = VOUT(NOMINAL) + 0.55V ILOAD = 1mA ILOAD = 10mA (Notes 6, 8) ILOAD = 50mA ILOAD = 100mA Quiescent Current in VIN = 45V, VSHDN = 0V Shutdown ADJ Pin Bias Current VIN = 2.1V (Notes 4, 9) Output Voltage Noise COUT = 10µF, ILOAD = 100mA, CBYP = 0.01µF VOUT = 600mV, BW = 10Hz to 100kHz Shutdown Threshold VOUT = Off to On VOUT = On to Off SHDN Pin Current VSHDN = 0V VSHDN = 45V (Note 10) Ripple Rejection LT3060-1.2: VIN = 2.7V (Avg) VRIPPLE = 0.5VP-P, LT3060-1.5: VIN = 3V (Avg) fRIPPLE = 120Hz, LT3060-1.8: VIN = 3.3V (Avg) ILOAD = 100mA LT3060-2.5: VIN = 4V (Avg) LT3060-3.3: VIN = 4.8V (Avg) LT3060-5: LT3060: Current Limit Input Reverse Leakage Current Reverse Output Current (Note 11) VIN = 6.5V (Avg) VIN = 2.1V (Avg) (Note 4) l l elecTrical characTerisTics PARAMETER Dropout Voltage VIN = VOUT(NOMINAL) (Notes 6, 7) MIN l TYP 75 150 l 240 l 300 l l l l l l 40 60 160 0.8 2 0.3 15 30 MAX 110 180 200 300 280 410 350 510 80 100 350 1.8 4 1 60 UNITS mV mV mV mV mV mV mV mV µA µA µA mA mA µA nA µVRMS l l l l l 0.3 0.8 0.7 0.9 79 77 75 73 70 67 85 200 1.5 1 3 64 62 60 58 55 52 70 110 V V µA µA dB dB dB dB dB dB dB mA mA µA µA µA µA µA µA µA µA VIN = 7V, VOUT = 0 VIN = VOUT(NOMINAL) + 1V (Notes 6, 12), ΔVOUT = – 5% VIN = – 45V, VOUT = 0 LT3060-1.2: VOUT = 1.2V, VIN = 0V LT3060-1.5: VOUT = 1.5V, VIN = 0V LT3060-1.8: VOUT = 1.8V, VIN = 0V LT3060-2.5: VOUT = 2.5V, VIN = 0V LT3060-3.3: VOUT = 3.3V, VIN = 0V LT3060-5: LT3060: VOUT = 5V, VIN = 0V VOUT = 1.2V, VIN = 0V (Note 4) 300 5 5 5 5 5 5 0.2 10 10 10 10 10 10 10 3060fa 6 LT3060 Series elecTrical characTerisTics Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Absolute maximum input-to-output differential voltage is not achievable with all combinations of rated IN pin and OUT pin voltages. With the IN pin at 50V, the OUT pin may not be pulled below 0V. The total measured voltage from IN to OUT must not exceed ±50V. Note 3: The LT3060 regulators are tested and specified under pulse load conditions such that TJ ≅ TA . The LT3060E regulators are 100% tested at TA = 25°C. Performance at –40°C to 125°C is assured by design, characterization and correlation with statistical process controls. The LT3060I regulators are guaranteed over the full –40°C to 125°C operating junction temperature range. The LT3060MP regulators are 100% tested over the –55°C to 125°C operating junction temperature range. The LT3060H regulators are 100% tested at the 150°C operating junction temperature. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125°C. Note 4: The LT3060 adjustable version is tested and specified for these conditions with the ADJ connected to the OUT pin. Note 5: Maximum junction temperature limits operating conditions. The regulated output voltage specification does not apply for all possible combinations of input voltage and output current. Limit the output current range if operating at the maximum input-to-output voltage differential. Limit the input-to-output voltage differential if operating at maximum output current. Current limit foldback will limit the maximum output current as a function of input-to-output voltage. See Current Limit vs VIN – VOUT in the Typical Performance Characteristics section. Note 6: To satisfy minimum input voltage requirements, the LT3060 adjustable version is tested and specified for these conditions with an external resistor divider (bottom 115k, top 365k) for an output voltage of 2.5V. The external resistor divider adds 5µA of DC load on the output. This external current is not factored into GND pin current. Note 7: Dropout voltage is the minimum input-to-output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage equals: (VIN – VDROPOUT). For the LT3060, LT3060-1.2, LT3060-1.5 and LT3060-1.8, dropout is limited by the minimum input specification under some output voltages and load conditions. See the Minimum Input Voltage curve in the Typical Performance Characteristics section. Note 8: GND pin current is tested with VIN = VOUT(NOMINAL) + 0.55V and a current source load. GND pin current will increase in dropout. See GND pin current curves in the Typical Performance Characteristics section. Note 9: ADJ pin bias current flows out of the ADJ pin. Note 10: SHDN pin current flows into the SHDN pin. Note 11: Reverse output current is tested with the IN pin grounded and the OUT pin forced to the rated output voltage. This current flows into the OUT pin and out of the GND pin. Note 12: To satisfy requirements for minimum input voltage, current limit is tested at VIN = VOUT(NOMINAL) + 1V or VIN = 2.1V, whichever is greater. Note 13: This IC includes overtemperature protection that protects the device during momentary overload conditions. Junction temperature will exceed 125°C (LT3060E, LT3060I, LT3060MP) or 150°C (LT3060H) when overtemperature circuitry is active. Continuous operation above the specified maximum junction temperature may impair device reliability. Note 14: The dropout voltage specification is guaranteed for the DFN package. The dropout voltage specification for high output currents cannot be guaranteed for the TS8 package due to production test limitations. Note 15: The load regulation specification is guaranteed for the fixed voltage options in the DFN package. The load regulation specification cannot be guaranteed for the fixed voltage options in the TS8 package due to production test limitations. The TS8 packages are tested similarly to the LT3060 adjustable version with the ADJ connected to the OUT pin. 3060fa 7 LT3060 Series Typical perForMance characTerisTics Typical Dropout Voltage 550 GUARANTEED DROPOUT VOLTAGE (mV) 500 450 DROPOUT VOLTAGE (mV) 400 350 300 250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 90 100 OUTPUT CURRENT (mA) 3060 G01 TA = 25°C, unless otherwise noted. Guaranteed Dropout Voltage 550 500 450 400 350 300 250 200 150 100 50 0 0 10 20 30 40 50 60 70 80 90 100 OUTPUT CURRENT (mA) 3060 G02 Dropout Voltage 550 500 450 IL = 100mA IL = 50mA = TEST POINTS TJ ≤ 150°C DROPOUT VOLTAGE (mV) 400 350 300 250 200 150 100 50 TJ = 125°C TJ ≤ 25°C TJ = 25°C IL = 10mA IL = 1mA 0 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G03 Quiescent Current 80 VIN = 6V, VSHDN = VIN 70 RL = ∞ (120k FOR LT3060) IL = 0 (5µA FOR LT3060) QUIESCENT CURRENT (µA) OUTPUT VOLTAGE (V) 60 50 40 30 20 10 VSHDN = 0V LT3060-1.2/-1.5/-1.8/-2.5/-3.3/-5 1.216 1.208 1.204 1.200 1.196 1.192 1.188 1.184 1.180 LT3060-1.2 Output Voltage 1.224 I = 1mA 1.220 L 1.212 1.520 OUTPUT VOLTAGE (V) 1.515 1.510 1.505 1.500 1.495 1.490 1.485 1.480 1.475 LT3060-1.5 Output Voltage 1.530 I = 1mA 1.525 L LT3060 0 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G04 1.176 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G05 1.470 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G06 LT3060-1.8 Output Voltage 1.836 I = 1mA 1.830 L 1.824 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.818 1.812 1.806 1.800 1.794 1.788 1.782 1.776 1.770 1.764 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G07 LT3060-2.5 Output Voltage 2.55 2.54 2.53 2.52 2.51 2.50 2.49 2.48 2.47 2.46 2.45 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G08 LT3060-3.3 Output Voltage 3.366 I = 1mA 3.355 L 3.344 OUTPUT VOLTAGE (V) 3.333 3.322 3.311 3.300 3.289 3.278 3.267 3.256 3.245 3.234 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G09 IL = 1mA 3060fa 8 LT3060 Series Typical perForMance characTerisTics LT3060-5 Output Voltage 5.10 5.08 5.06 OUTPUT VOLTAGE (V) ADJ PIN VOLTAGE (V) 5.04 5.02 5.00 4.98 4.96 4.94 4.92 4.90 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G10 TA = 25°C, unless otherwise noted. LT3060 ADJ Pin Voltage 0.612 IL = 1mA 0.610 V = 2.1V IN 0.608 QUIESCENT CURRENT (µA) 0.606 0.604 0.602 0.600 0.598 0.596 0.594 0.592 0.590 0.588 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G11 200 LT3060-1.2 Quiescent Current TJ = 25°C 175 RL = 240k VOUT = 1.2V 150 125 100 75 50 25 0 VSHDN = 0V 0 1 2 34567 INPUT VOLTAGE (V) 8 9 10 3060 G12 IL = 1mA VSHDN = VIN LT3060-1.5 Quiescent Current 200 TJ = 25°C 175 RL = 300k VOUT = 1.5V QUIESCENT CURRENT (µA) QUIESCENT CURRENT (µA) 150 125 100 75 50 25 0 VSHDN = 0V 0 1 2 34567 INPUT VOLTAGE (V) 8 9 10 VSHDN = VIN 200 LT3060-1.8 Quiescent Current TJ = 25°C 175 RL = 360k VOUT = 1.8V 150 125 100 75 50 25 0 0 1 2 VSHDN = VIN QUIESCENT CURRENT (µA) 200 LT3060-2.5 Quiescent Current TJ = 25°C 175 RL = 500k VOUT = 2.5V 150 125 100 75 50 25 VSHDN = VIN VSHDN = 0V 34567 INPUT VOLTAGE (V) 8 9 10 3060 G14 0 VSHDN = 0V 0 1 2 34567 INPUT VOLTAGE (V) 8 9 10 3060 G15 3060 G13 LT3060-3.3 Quiescent Current 200 TJ = 25°C 175 RL = 660k VOUT = 3.3V QUIESCENT CURRENT (µA) QUIESCENT CURRENT (µA) 150 125 100 75 50 25 0 0 1 2 VSHDN = VIN 200 LT3060-5 Quiescent Current TJ = 25°C 175 RL = 1M VOUT = 5V 150 125 100 75 50 25 VSHDN = VIN 80 70 QUIESCENT CURRENT (µA) 60 50 40 30 20 10 VSHDN = 0V 0 1 2 34567 INPUT VOLTAGE (V) 8 9 10 3060 G17 LT3060 Quiescent Current TJ = 25°C RL = 120k VOUT = 0.6V VSHDN = VIN VSHDN = 0V 34567 INPUT VOLTAGE (V) 8 9 10 3060 G16 0 0 VSHDN = 0 0 5 10 15 20 25 30 35 INPUT VOLTAGE (V) 40 45 3060 G18 3060fa 9 LT3060 Series Typical perForMance characTerisTics LT3060-1.2 GND Pin Current 2.50 2.25 2.00 GND PIN CURRENT (mA) 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 0 1 2 RL = 1.2k IL = 1mA* RL = 24 IL = 50mA* RL = 120 IL = 10mA* 8 9 10 3060 G19 TA = 25°C, unless otherwise noted. LT3060-1.5 GND Pin Current 2.50 2.25 2.00 GND PIN CURRENT (mA) 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 0 1 2 RL = 1.5k IL = 1mA* RL = 30 IL = 50mA* RL = 150 IL = 10mA* 8 9 10 3060 G20 LT3060-1.8 GND Pin Current 2.50 2.25 2.00 GND PIN CURRENT (mA) 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 0 1 2 RL = 1.8k IL = 1mA* RL = 36 IL = 50mA* RL = 180 IL = 10mA* 8 9 10 3060 G21 TJ = 25°C *FOR VOUT = 1.2V VSHDN = VIN RL = 12 IL = 100mA* TJ = 25°C *FOR VOUT = 1.5V VSHDN = VIN RL = 15 IL = 100mA* TJ = 25°C *FOR VOUT = 1.8V VSHDN = VIN RL = 18 IL = 100mA* 34567 INPUT VOLTAGE (V) 34567 INPUT VOLTAGE (V) 34567 INPUT VOLTAGE (V) LT3060-2.5 GND Pin Current 2.50 2.25 2.00 GND PIN CURRENT (mA) 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 0 1 2 RL = 2.5k IL = 1mA* RL = 50 IL = 50mA* RL = 250 IL = 10mA* 8 9 10 3060 G22 LT3060-3.3 GND Pin Current 2.50 2.25 2.00 GND PIN CURRENT (mA) 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 0 1 2 RL = 3.3k IL = 1mA* RL = 66 IL = 50mA* RL = 330 IL = 10mA* 8 9 10 3060 G23 LT3060-5 GND Pin Current 2.50 2.25 2.00 GND PIN CURRENT (mA) 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 0 2 RL = 5k IL = 1mA* RL = 100 IL = 50mA* RL = 500 IL = 10mA* 8 9 10 3060 G24 TJ = 25°C *FOR VOUT = 2.5V VSHDN = VIN RL = 25 IL = 100mA* TJ = 25°C *FOR VOUT = 3.3V VSHDN = VIN RL = 33 IL = 100mA* TJ = 25°C *FOR VOUT = 5V VSHDN = VIN RL = 50 IL = 100mA* 34567 INPUT VOLTAGE (V) 34567 INPUT VOLTAGE (V) 34567 INPUT VOLTAGE (V) LT3060 GND Pin Current 2.50 2.25 2.00 GND PIN CURRENT (mA) 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 0 1 2 RL = 600 IL = 1mA* RL = 12 IL = 50mA* RL = 60 IL = 10mA* 8 9 10 RL = 6 IL = 100mA* TJ = 25°C *FOR VOUT = 0.6V VSHDN = VIN GND PIN CURRENT (mA) 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 GND Pin Current vs ILOAD VIN = VOUT(NOMINAL) + 1V 34567 INPUT VOLTAGE (V) 0 3060 G25 10 20 30 40 50 60 70 80 90 100 OUTPUT CURRENT (mA) 3060 G26 3060fa 10 LT3060 Series Typical perForMance characTerisTics SHDN Pin Threshold 1.5 1.4 1.3 1.2 1.1 1.0 0.9 OFF TO ON 0.8 0.7 0.6 ON TO OFF 0.5 0.4 0.3 0.2 0.1 0 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 2.0 1.8 SHDN PIN INPUT CURRENT (µA) SHDN PIN INPUT CURRENT (µA) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 30 35 SHDN PIN VOLTAGE (V) 40 45 TA = 25°C, unless otherwise noted. SHDN Pin Input Current 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 SHDN Pin Input Current VSHDN = 45V SHDN PIN THRESHOLD (V) 3060 G27 3060 G28 0 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G29 ADJ Pin Bias Current 50 40 ADJ PIN BIAS CURRENT (nA) 30 20 10 0 –10 –20 –30 –40 –50 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) CURRENT LIMIT (mA) 250 225 200 175 150 125 100 75 50 25 0 Current Limit vs VIN –VOUT TJ = 125°C TJ = 25°C TJ = – 50°C CURRENT LIMIT (mA) ∆VOUT = – 5% Current Limit vs Temperature 250 225 200 1-PHASE 175 2-PHASE 3-PHASE 150 4-PHASE 125 6-PHASE 100 75 50 25 VIN = 7V VOUT = 0V 0 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G32 0 5 3060 G30 10 15 20 25 30 35 40 INPUT/OUTPUT DIFFERENTIAL (V) 45 3060 G31 LT3060 Reverse Output Current 2.0 REVERSE OUTPUT CURRENT (mA) REVERSE OUTPUT CURRENT (µA) TJ = 25°C 1.8 VIN = 0V CURRENT FLOWS 1.6 INTO OUT PIN 1.4 VOUT = VADJ 1.2 1.0 0.8 0.6 0.4 0.2 0 0 5 10 OUT 15 20 25 30 35 OUTPUT VOLTAGE (V) 40 45 ADJ 350 300 250 200 150 100 50 0 LT3060-1.2/-1.5/-1.8/-2.5/-3.3/-5 Reverse Output Current REVERSE OUTPUT CURRENT (µA) TJ = 25°C VIN = 0V LT3060-1.2 LT3060-1.5 LT3060-1.8 LT3060-2.5 LT3060-3.3 50 45 40 35 30 25 20 Reverse Output Current VIN = 0V, VOUT = VADJ = 1.2V (LT3060) VOUT = 1.2V (LT3060-1.2) VOUT = 1.5V (LT3060-1.5) VOUT = 1.8V (LT3060-1.8) VOUT = 2.5V (LT3060-2.5) VOUT = 3.3V (LT3060-3.3) VOUT = 5V (LT3060-5) ADJ (LT3060) LT3060-5 0 5 10 15 20 25 30 35 OUTPUT VOLTAGE (V) 40 45 3060 G33 3060 G34 VOUT = 5V VOUT = 3.3V VOUT = 2.5V 10 OUT (LT3060-1.2/-1.5/ VOUT -1.8/2.5/-3.3/-5)= 1.8V 5 VOUT = 1.5V .2V VOUT = 1OUT (LT3060) 0 V 0 0.6V –75 –50 –25 OUT = 25 50 75 100 125 150 175 TEMPERATURE (°C) 15 3060 G35 3060fa 11 LT3060 Series Typical perForMance characTerisTics Input Ripple Rejection 100 90 80 RIPPLE REJECTION (dB) RIPPLE REJECTION (dB) 70 60 50 40 30 I = 100mA 20 L CREF/BYP = CFF = 0 10 VIN = VOUT(NOMINAL) + 1.5V + COUT = 2.2µF 50mVRMS RIPPLE 0 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) 3060 G36 TA = 25°C, unless otherwise noted. LT3060-5 Input Ripple Rejection 100 90 80 CREF/BYP = CFF = 10nF CREF/BYP = 10nF CFF = 0 , RIPPLE REJECTION (dB) 100 90 80 70 60 50 40 30 Ripple Rejection vs Temperature CREF/BYP = 10nF CREF/BYP = 0 VOUT = 0.6V VOUT = 5V 70 60 50 40 30 IL = 100mA VOUT = 5V CREF/BYP = CFF = 0 10 COUT = 10µF VIN = 6V + 50mVRMS RIPPLE 0 10 100 1k 10k 100k 1M FREQUENCY (Hz) 20 COUT = 10µF 10M 3060 G37 20 I = 100mA L 10 VOUT = 0.6V VIN = 2.6V + 0.5VP-P RIPPLE AT f = 120Hz 0 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G38 Minimum Input Voltage 2.2 2.0 MINIMUM INPUT VOLTAGE (V) 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G39 VSHDN = VIN IL = 50mA IL = 100mA LOAD REGULATION (mV) 0 –5 –10 –15 –20 LT3060-5 LT3060-3.3 LT3060-2.5 LT3060-1.8 LT3060-1.5 LT3060-1.2 LT3060 OUTPUT NOISE SPECTRAL DENSITY (µV/√Hz) 5 Load Regulation 10 Output Noise Spectral Density CREF/BYP = 0, CFF = 0 1 0.1 –25 –75 –50 –25 0 25 50 75 100 125 150 175 TEMPERATURE (°C) 3060 G40 VIN = VOUT(NOMINAL) + 0.55V (LT3060-1.8/-2.5/-3.3/-5) VIN = 2.1V (LT3060/-1.2/-1.5) ∆IL = 1mA TO 100mA 0.01 VOUT = 5V VOUT = 3.3V VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.6V 10 100 COUT = 10µF IL = 100mA 100k 3060 G41 1k 10k FREQUENCY (Hz) OUTPUT NOISE SPECTRAL DENSITY (µV/√Hz) VOUT = 5V CREF/BYP = 100pF OUTPUT NOISE SPECTRAL DENSITY (µV/√Hz) 10 Output Noise Spectral Density vs CREF/BYP, CFF = 0 10 Output Noise Spectral Density vs CFF, CREF/BYP = 10nF 1 VOUT = 0.6V 1 CFF = 10nF CFF = 0 0.1 CREF/BYP = 10nF COUT = 10µF IL = 100mA 10 100 CREF/BYP = 1nF 0.1 VOUT = 5V COUT = 10µF IL = 100mA 10 100 CFF = 1nF CFF = 100pF 100k 3060 G43 0.01 1k 10k FREQUENCY (Hz) 100k 3060 G42 0.01 1k 10k FREQUENCY (Hz) 3060fa 12 LT3060 Series Typical perForMance characTerisTics 110 OUTPUT NOISE VOLTAGE (µVRMS) TA = 25°C, unless otherwise noted. RMS Output Noise vs Feedforward Capacitor (CFF) VOUT = 5V VOUT = 3.3V VOUT = 2.5V f = 10Hz TO 100kHz CREF/BYP = 10nF COUT = 10µF IFB-DIVIDER = 5µA IL = 100mA RMS Output Noise vs Load Current vs CREF/BYP, CFF = 0 CREF/BYP = 0 OUTPUT NOISE VOLTAGE (µVRMS) CREF/BYP = 10pF OUTPUT NOISE VOLTAGE (µVRMS) VOUT = 0.6V 100 COUT = 10µF 90 80 70 60 50 40 30 20 10 0 0.01 CREF/BYP = 1nF CREF/BYP = 10nF CREF/BYP = 100pF CREF/BYP = 100nF 0.1 1 10 LOAD CURRENT (mA) 100 3060 G44 170 160 f = 10Hz TO 100kHz VOUT = 5V 150 COUT = 10µF 140 VOUT = 2.5V 130 VOUT = 3.3V 120 VOUT = 1.8V 110 100 VOUT = 1.5V 90 80 70 60 50 40 VOUT = 1.2V 30 20 VOUT = 0.6V 10 0 1 10 100 0.01 0.1 LOAD CURRENT (mA) 3060 G45 RMS Output Noise vs Load Current CREF/BYP = 10nF, CFF = 0 120 110 100 90 80 70 60 50 40 30 VOUT = 0.6V 20 V VOUT = 1.2V OUT = 1.8V 10 VOUT = 1.5V 0 1n 10n 10p 100p FEEDFORWARD CAPACITOR, CFF (F) 3060 G46 LT3060-5 10Hz to 100kHz Output Noise, CREF/BYP = 10nF, CFF = 0 LT3060-5 10Hz to 100kHz Output Noise, CREF/BYP = 10nF, CFF = 10nF VOUT 100µV/DIV VOUT 100µV/DIV COUT = 10µF IL = 100mA VOUT = 5V 1ms/DIV 3060 G47 COUT = 10µF IL = 100mA VOUT = 5V 1ms/DIV 3060 G48 LT3060-5 Transient Response, CFF = 0 VOUT 50mV/DIV VOUT = 5V VOUT 20mV/DIV LT3060-5 Transient Response, CFF = 10nF VOUT = 5V ∆IOUT = 10mA TO 100mA IOUT 50mA/DIV VIN = 6V 100µs/DIV COUT = CIN = 10µF IFB-DIVIDER = 5µA 3060 G49 ∆IOUT = 10mA TO 100mA IOUT 50mA/DIV VIN = 6V 20µs/DIV COUT = CIN = 10µF IFB-DIVIDER = 5µA 3060 G50 3060fa 13 LT3060 Series Typical perForMance characTerisTics LT3060-5 Transient Response Load Dump VOUT VOUT = 5V 10mV/DIV VIN = 12V TO 45V VOUT 2V/DIV RL = 50 REF/BYP 500mV/DIV VIN 10V/DIV 2ms/DIV 3060 G51 TA = 25°C, unless otherwise noted. SHDN Transient Response CREF/BYP = 10nF VOUT 2V/DIV RL = 50 REF/BYP 500mV/DIV SHDN 1V/DIV 3060 G53 SHDN Transient Response CREF/BYP = 0 SHDN 1V/DIV 3060 G52 COUT = CIN = 2.2µF CREF/BYP = CFF = 10nF IFB-DIVIDER = 5µA COUT = CIN = 2.2µF CFF = 0 4ms/DIV COUT = CIN = 2.2µF CFF = 0 4ms/DIV Start-Up Time vs REF/BYP Capacitor 100 CFF = 0 100 Start-Up Time vs CFF CREF/BYP = 0 IFB-DIVIDER = 5µA LT3060-5 START-UP TIME (ms) START-UP TIME (ms) 10 10 LT3060-3.3 1 1 LT3060-2.5 LT3060-1.8 0.1 0.1 LT3060-1.2 LT3060-1.5 0.01 10p 100p 10n 1n REF/BYP CAPACITOR (F) 100n 3060 G54 0.01 10p 100p 1n 10n FEEDFORWARD CAPACITOR, CFF (F) 100n 3060 G55 3060fa 14 LT3060 Series pin FuncTions (DC8/TS8) REF/BYP (Pin 1/Pin 8): Reference/Bypass. Connecting a single capacitor from this pin to GND bypasses the LT3060’s reference noise and soft-starts the reference. A 10nF bypass capacitor typically reduces output voltage noise to 30µVRMS in a 10Hz to 100kHz bandwidth. Softstart time is directly proportional to the REF/BYP capacitor value. If the LT3060 is placed in shutdown, REF/BYP is actively pulled low by an internal device to reset soft-start. If low noise or soft-start performance is not required, this pin must be left floating (unconnected). Do not drive this pin with any active circuitry. ADJ (Pin 2/Pin 7): Adjust. This pin is the error amplifier’s inverting terminal. It’s typical bias current of 15nA flows out of the pin (see curve of ADJ Pin Bias Current vs Temperature in the Typical Performance Characteristics section). The ADJ pin voltage is 600mV referenced to GND. Connecting a capacitor from ADJ to OUT reduces output noise and improves transient response for output voltages greater than 600mV. See the Applications Information section for calculating the value of the feedforward capacitor. For fixed voltage versions of the LT3060, if low noise and fast transient response is not required, this pin must be left floating (unconnected). OUT (Pins 3, 4/Pin 6): Output. These pin(s) supply power to the load. Stability requirements demand a minimum 2.2µF ceramic output capacitor to prevent oscillations. Large load transient applications require larger output capacitors to limit peak voltage transients. See the Applications Information section for details on transient response and reverse output characteristics. Permissible output voltage range is 600mV to 44.5V. IN (Pins 5, 6/Pin 5): Input. These pin(s) supply power to the device. The LT3060 requires a local IN bypass capacitor if it is located more than six inches from the main input filter capacitor. In general, battery output impedance rises with frequency, so adding a bypass capacitor in batterypowered circuits is advisable. An input bypass capacitor in the range of 1µF to 10µF suffices. The LT3060 withstands reverse voltages on the IN pin with respect to its GND and OUT pins. In a reversed input situation, such as a battery plugged in backwards, the LT3060 behaves as if a large resistor is in series with its input. Limited reverse current flows into the LT3060 and no reverse voltage appears at the load. The device protects itself and the load. SHDN (Pin 7/Pin 1): Shutdown. Pulling the SHDN pin low puts the LT3060 into a low power state and turns the output off. Drive the SHDN pin with either logic or an open collector/drain with a pull-up resistor. The resistor supplies the pull-up current to the open collector/drain logic, normally several microamperes, and the SHDN pin current, typically less than 3µA. If unused, connect the SHDN pin to IN. The LT3060 does not function if the SHDN pin is not connected. The SHDN pin cannot be driven below GND unless tied to the IN pin. If the SHDN pin is driven below GND while IN is powered, the output may turn on. SHDN pin logic cannot be referenced to a negative supply voltage. GND (Pin 8, Exposed Pad Pin 9/Pins 2, 3, 4): Ground. For the adjustable LT3060, connect the bottom of the external resistor divider that sets the output voltage directly to GND for optimum regulation. For the DFN package, tie exposed pad Pin 9 directly to Pin 8 and the PCB ground. This exposed pad provides enhanced thermal performance with its connection to the PCB ground. See the Applications Information section for thermal considerations and calculating junction temperature. 3060fa 15 LT3060 Series applicaTions inForMaTion The LT3060 series are micropower, low noise, low dropout voltage, 100mA linear regulators with shutdown. The devices supply up to 100mA at a typical dropout voltage of 300mV and operate over a 1.6V to 45V input range. A single external capacitor provides programmable low noise reference performance and output soft-start functionality. For example, connecting a 10nF capacitor from the REF/BYP pin to GND lowers output noise to 30µVRMS over a 10Hz to 100kHz bandwidth. This capacitor also soft-starts the reference and prevents output voltage overshoot at turn-on. The LT3060’s quiescent current is merely 40μA for the adjustable version and 45µA for the fixed voltage versions, while providing fast transient response with a minimum low ESR 2.2μF ceramic output capacitor. In shutdown, quiescent current is less than 1μA and the reference softstart capacitor is reset. The LT3060 regulators optimize stability and transient response with low ESR, ceramic output capacitors. The regulators do not require the addition of ESR as is common with other regulators. The LT3060 adjustable version typically provides 0.1% line regulation and 0.03% load regulation. For fixed voltage versions, load regulation is slightly increased due to 20mΩ of typical resistance in series with the output. Curves of load regulation appear in the Typical Performance Characteristics section. Internal protection circuitry includes reverse-battery protection, reverse-output protection, reverse-current protection, current limit with foldback and thermal shutdown. This “bullet-proof” protection set makes it ideal for use in battery-powered systems. In battery backup applications where the output is held up by a backup battery and the input is pulled to ground, the LT3060 acts like it has a diode in series with its output and prevents reverse current flow. Additionally, in dual supply applications where the regulator load is returned to a negative supply, the output can be pulled below ground by as much as 45V and the device still starts normally and operates. Adjustable Operation The LT3060 adjustable version has an output voltage range of 0.6V to 44.5V. The output voltage is set by the ratio of two external resistors, as shown in Figure 1. The device servos the output to maintain the ADJ pin voltage at 0.6V referenced to ground. The current in R1 is then equal to 0.6V/R1, and the current in R2 is the current in R1 minus the ADJ pin bias current. The ADJ pin bias current, 15nA at 25°C, flows from the ADJ pin through R1 to GND. Calculate the output voltage using the formula in Figure 1. The value of R1 should be no greater than 124k to provide a minimum 5µA load current so that errors in the output voltage, caused by the ADJ pin bias current, are minimized. Note that in shutdown, the output is turned off and the divider current is zero. Curves of ADJ Pin Voltage vs Temperature and ADJ Pin Bias Current vs Temperature appear in the Typical Performance Characteristics section. The adjustable device is tested and specified with the ADJ pin tied to the OUT pin, yielding VOUT = 0.6V. Specifications for output voltages greater than 0.6V are proportional to the ratio of the desired output voltage to 0.6V: VOUT /0.6V. For example, load regulation for an output current change of 1mA to 100mA is 0.2mV (typical) at VOUT = 0.6V. At VOUT = 12V, load regulation is: 12V • (0.2mV) = 4mV 0.6 V IN VIN OUT LT3060 SHDN ADJ R1 R2 VOUT = 0.6 V 1+ VADJ = 0.6 V IADJ = 15nA at 25º C 3060 F01 VOUT R2 – IADJ • R2 R1 GND REF/BYP ( ) OUTPUT RANGE = 0.6 V to 44.5V Figure 1. Adjustable Operation 3060fa 16 LT3060 Series applicaTions inForMaTion Table 1 shows 1% resistor divider values for some common output voltages with a resistor divider current of about 5µA. Table 1. Output Voltage Resistor Divider Values VOUT (V) 1.2 1.5 1.8 2.5 3 3.3 5 R1 (k Ω) 118 121 124 115 124 124 115 R2 (k Ω) 118 182 249 365 499 562 845 To lower the output voltage noise for higher output voltages, include a feedforward capacitor (CFF) from VOUT to the ADJ pin. A good quality, low leakage capacitor is recommended. This capacitor bypasses the error amplifier of the regulator, providing a low frequency noise pole. With the use of 10nF for both CFF and CREF/BYP, output voltage noise decreases to 30µVRMS when the output voltage is set to 5V by a 5µA feedback resistor divider. If the current in the feedback resistor divider is doubled, CFF must also be doubled to achieve equivalent noise performance. Higher values of output voltage noise are often measured if care is not exercised with regard to circuit layout and testing. Crosstalk from nearby traces induces unwanted noise onto the LT3060’s output. Power supply ripple rejection must also be considered. The LT3060 regulators do not have unlimited power supply rejection and will pass a small portion of the input noise through to the output. Using a feedforward capacitor (CFF) from VOUT to the ADJ pin has the added benefit of improving transient response for output voltages greater than 0.6V. With no feedforward capacitor, the settling time will increase as the output voltage is raised above 0.6V. Use the equation in Figure 2 to determine the minimum value of CFF to achieve a transient response that is similar to 0.6V output voltage performance regardless of the chosen output voltage (see Figure 3 and Transient Response in the Typical Performance Characteristics section). Bypass Capacitance, Output Voltage Noise and Transient Response The LT3060 regulators provide low output voltage noise over the 10Hz to 100kHz bandwidth while operating at full load with the addition of a reference bypass capacitor (CREF/BYP) from the REF/BYP pin to GND. A good quality, low leakage capacitor is recommended. This capacitor bypasses the internal reference of the regulator, providing a low frequency noise pole. With the use of 10nF for CREF/BYP, the output voltage noise decreases to as low as 30µVRMS when the output voltage is set for 0.6V. For higher output voltages (generated by using a feedback resistor divider), the output voltage noise gains up accordingly when using CREF/BYP by itself. FEEDFORWARD CAPACITOR, CFF IN VIN OUT LT3060 R2 CFF VOUT COUT 0 VOUT = 5V COUT = 10µF IFB-DIVIDER = 5µA VOUT 50mV/DIV SHDN ADJ R1 4.7nF • IFB−DIVIDER 5µA V IFB−DIVIDER = OUT R1+ R 2 CFF ≥ 100pF 1nF 10nF GND REF/BYP CREF/BYP 3060 F02 ( ) LOAD CURRENT 100mA/DIV 100µs/DIV 3060 F03 Figure 2. Feedforward Capacitor for Fast Transient Response Figure 3. Transient Response vs Feedforward Capacitor 3060fa 17 LT3060 Series applicaTions inForMaTion During start-up, the internal reference soft-starts if a reference bypass capacitor is present. Regulator startup time is directly proportional to the size of the bypass capacitor, slowing to 6ms with a 10nF bypass capacitor (See Start-up Time vs REF/BYP Capacitor in the Typical Performance Characteristics section). The reference bypass capacitor is actively pulled low during shutdown to reset the internal reference. Start-up time is also affected by the use of a feedforward capacitor. Start-up time is directly proportional to the size of the feedforward capacitor and output voltage, and is inversely proportional to the feedback resistor divider current, slowing to 15ms with a 4.7nF feedforward capacitor and a 10µF output capacitor for an output voltage set to 5V by a 5µA feedback resistor divider. Output Capacitance The LT3060 regulators are stable with a wide range of output capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. Use a minimum output capacitor of 2.2µF with an ESR of 3Ω or less to prevent oscillations. If a feedforward capacitor is used with output voltages set for greater than 24V, use a minimum output capacitor of 4.7µF. The LT3060 is a micropower device and output load transient response is a function of output capacitance. Larger values of output capacitance decrease the peak deviations and provide improved transient response for larger load current 20 0 CHANGE IN VALUE (%) –20 –40 –60 –80 –100 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10µF CHANGE IN VALUE (%) X5R changes. Bypass capacitors, used to decouple individual components powered by the LT3060, increase the effective output capacitor value. For applications with large load current transients, a low ESR ceramic capacitor in parallel with a bulk tantalum capacitor often provides an optimally damped response. Give extra consideration to the use of ceramic capacitors. Manufacturers make ceramic capacitors with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics are specified with EIA temperature characteristic codes of Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics provide high C-V products in a small package at low cost , but exhibit strong voltage and temperature coefficients, as shown in Figures 4 and 5. When used with a 5V regulator, a 16V 10µF Y5V capacitor can exhibit an effective value as low as 1µF to 2µF for the DC bias voltage applied, and over the operating temperature range. The X5R and X7R dielectrics yield much more stable characteristics and are more suitable for use as the output capacitor. The X7R type works over a wider temperature range and has better temperature stability, while the X5R is less expensive and is available in higher values. Care still must be exercised when using X5R and X7R capacitors; the X5R and X7R codes only specify operating temperature range and maximum capacitance change over temperature. Capacitance change due to DC bias with X5R and X7R capacitors is better than Y5V and Z5U 40 20 0 –20 –40 –60 –80 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10µF 50 25 75 0 TEMPERATURE (°C) 100 125 3060 F05 X5R Y5V Y5V 0 2 4 8 6 10 12 DC BIAS VOLTAGE (V) 14 16 3060 F04 –100 –50 –25 Figure 4. Ceramic Capacitor DC Bias Characteristics Figure 5. Ceramic Capacitor Temperature Characteristics 3060fa 18 LT3060 Series applicaTions inForMaTion capacitors, but can still be significant enough to drop capacitor values below appropriate levels. Capacitor DC bias characteristics tend to improve as component case size increases, but expected capacitance at operating voltage should be verified. Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress, similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor, the stress is induced by vibrations in the system or thermal transients. The resulting voltages produced cause appreciable amounts of noise. A ceramic capacitor produced the trace in Figure 6 in response to light tapping from a pencil. Similar vibration induced behavior can masquerade as increased output voltage noise. VOUT = 0.6V COUT = 10µF CREF/BYP = 10nF ILOAD = 100mA VOUT 500µV/DIV allowing the regulator to supply large output currents. With a high input voltage, a problem can occur wherein the removal of an output short will not allow the output to recover. Other regulators, such as the LT1083/LT1084/LT1085 family and LT1764A also exhibit this phenomenon, so it is not unique to the LT3060. The problem occurs with a heavy output load when the input voltage is high and the output voltage is low. Common situations are: (1) immediately after the removal of a short-circuit or (2) if the shutdown pin is pulled high after the input voltage is already turned on. The load line intersects the output current curve at two points creating two stable output operating points for the regulator. With this double intersection, the input power supply needs to be cycled down to zero and brought up again for the output to recover. Thermal Considerations The power handling capability of the device will be limited by the maximum rated junction temperature (125°C for LT3060E, LT3060I, LT3060MP or 150°C for LT3060H). Two components comprise the power dissipated by the device: 1. Output current multiplied by the input/output voltage differential: IOUT • (VIN –VOUT), and 4ms/DIV 3060 F06 2. GND pin current multiplied by the input voltage: IGND • VIN GND pin current is determined using the GND Pin Current curves in the Typical Performance Characteristics section. Power dissipation equals the sum of the two components listed above. The LT3060 regulators have internal thermal limiting that protects the device during overload conditions. For continuous normal conditions, the maximum junction temperature of 125°C (E-grade, I-grade, MP-grade) or 150°C (H-grade) must not be exceeded. Carefully consider all sources of thermal resistance from junction-to-ambient including other heat sources mounted in proximity to the LT3060. The underside of the LT3060 DFN package has exposed metal (1mm2) from the lead frame to the die attachment. The package allows heat to directly transfer from the die junction to the printed circuit board metal to control maximum operating junction temperature. The dual-in-line pin 3060fa Figure 6. Noise Resulting from Tapping on a Ceramic Capacitor Overload Recovery Like many IC power regulators, the LT3060 has safe operating area protection. The safe operating area protection decreases current limit as input-to-output voltage increases, and keeps the power transistor inside a safe operating region for all values of input-to-output voltage. The LT3060 provides some output current at all values of input-to-output voltage up to the specified 45V operational maximum. When power is first applied, the input voltage rises and the output follows the input; allowing the regulator to start-up into very heavy loads. During start-up, as the input voltage is rising, the input-to-output voltage differential is small, 19 LT3060 Series applicaTions inForMaTion arrangement allows metal to extend beyond the ends of the package on the topside (component side) of a PCB. Connect this metal to GND on the PCB. The multiple IN and OUT pins of the LT3060 also assist in spreading heat to the PCB. For surface mount devices, heat sinking is accomplished by using the heat spreading capabilities of the PC board and its copper traces. Copper board stiffeners and plated through-holes also can spread the heat generated by power devices. Tables 2 and 3 list thermal resistance for several different board sizes and copper areas. All measurements were taken in still air on a 4 layer FR-4 board with 1oz solid internal planes and 2oz top/bottom external trace planes with a total board thickness of 1.6mm. The four layers were electrically isolated with no thermal vias present. PCB layers, copper weight, board layout and thermal vias will affect the resultant thermal resistance. For more information on thermal resistance and high thermal conductivity test boards, refer to JEDEC standard JESD51, notably JESD51-12 and JESD51-7. Achieving low thermal resistance necessitates attention to detail and careful PCB layout. Table 2. DC Package, 8-Lead DFN COPPER AREA TOPSIDE* BACKSIDE (mm2) (mm2) 2500 1000 225 100 50 2500 2500 2500 2500 2500 BOARD AREA (mm2) 2500 2500 2500 2500 2500 THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 48°C/W 49°C/W 50°C/W 54°C/W 60°C/W Calculating Junction Temperature Example: Given an output voltage of 2.5V, an input voltage range of 12V ±5%, an output current range of 0mA to 50mA and a maximum ambient temperature of 85°C, what will the maximum junction temperature be? The power dissipated by the device equals: IOUT(MAX) • (VIN(MAX)–VOUT) + IGND • VIN(MAX) where, IOUT(MAX) = 50mA VIN(MAX) = 12.6V IGND at (IOUT = 50mA, VIN = 12.6V) = 0.6mA So, P = 50mA • (12.6V – 2.5V) + 0.6mA • 12.6V = 0.513W Using a DFN package, the thermal resistance ranges from 48°C/W to 60°C/W depending on the copper area with no thermal vias. So the junction temperature rise above ambient approximately equals: 0.513W • 54°C/W = 27.8°C The maximum junction temperature equals the maximum ambient temperature plus the maximum junction temperature rise above ambient or: TJMAX = 85°C + 27.8°C = 112.8°C Protection Features The LT3060 regulators incorporate several protection features that make it ideal for use in battery-powered circuits. In addition to the normal protection features associated with monolithic regulators, such as current limiting and thermal limiting, the device also protects against reverse-input voltages, reverse-output voltages and reverse output-to-input voltages. Current limit protection and thermal overload protection protect the device against current overload conditions at the output of the device. The typical thermal shutdown temperature is 165°C. For normal operation, do not exceed a junction temperature of 125°C (LT3060E, LT3060I, LT3060MP) or 150°C (LT3060H). 3060fa *Device is mounted on topside Table 3. TS8 Package, 8 Lead TSOT-23 COPPER AREA TOPSIDE* BACKSIDE (mm2) (mm2) 2500 1000 225 100 50 2500 2500 2500 2500 2500 BOARD AREA (mm2) 2500 2500 2500 2500 2500 THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 57°C/W 58°C/W 59°C/W 63°C/W 67°C/W *Device is mounted on topside 20 LT3060 Series applicaTions inForMaTion The LT3060 IN pin withstands reverse voltages up to 50V. The device limits current flow to less than 300µA (typically less than 50µA) and no negative voltage appears at OUT. The device protects both itself and the load against batteries that are plugged in backwards. The SHDN pin cannot be driven below GND unless tied to the IN pin. If the SHDN pin is driven below GND while IN is powered, the output may turn on. SHDN pin logic cannot be referenced to a negative supply voltage. The LT3060 incurs no damage if its output is pulled below ground. If the input is left open-circuit or grounded, the output can be pulled below ground by 50V. No current flows through the pass transistor from the output. However, current flows in (but is limited by) the resistor divider that sets the output voltage. Current flows from the bottom resistor in the divider and from the ADJ pin’s internal clamp through the top resistor in the divider to the external circuitry pulling OUT below ground. If the input is powered by a voltage source, the output sources current equal to its current limit capability and the LT3060 protects itself by thermal limiting. In this case, grounding the SHDN pin turns off the device and stops the output from sourcing current. 2.0 REVERSE OUTPUT CURRENT (mA) The LT3060 incurs no damage if the ADJ pin is pulled above or below ground by less than 50V. For the adjustable version, if the input is left open-circuit or grounded, the ADJ pin performs like a large resistor (typically 30k) in series with a diode when pulled below ground, and like 30k in series with two diodes when pulled above ground. In circuits where a backup battery is required, several different input/output conditions can occur. The output voltage may be held up while the input is either pulled to ground, pulled to some intermediate voltage or left opencircuit. Current flow back into the output follows the curve shown in Figures 7 and 8. If the LT3060’s IN pin is forced below the OUT pin or the OUT pin is pulled above the IN pin, input current typically drops to less than 1µA. This occurs if the LT3060 input is connected to a discharged (low voltage) battery and either a backup battery or a second regulator holds up the output. The state of the SHDN pin has no effect on the reverse current if the output is pulled above the input. REVERSE OUTPUT CURRENT (µA) TJ = 25°C 1.8 VIN = 0V CURRENT FLOWS 1.6 INTO OUT PIN 1.4 VOUT = VADJ 1.2 1.0 0.8 0.6 0.4 0.2 0 0 5 10 OUT 15 20 25 30 35 OUTPUT VOLTAGE (V) 40 45 ADJ 350 300 250 200 150 100 50 0 0 TJ = 25°C VIN = 0V LT3060-1.2 LT3060-1.5 LT3060-1.8 LT3060-2.5 LT3060-3.3 LT3060-5 5 10 15 20 25 30 35 OUTPUT VOLTAGE (V) 40 45 VOUT = 5 VOUT = 3 VOUT = 2 VOUT = 1 VOUT = 1 VOUT = 1 VOUT = 0 3060 F08w 3060 F07 Figure 7. LT3060 Reverse Output Current Figure 8. LT3060-1.2/-1.5/-1.8/-2.5/-3.3/-5 Reverse Output Current 3060fa 21 LT3060 Series Typical applicaTion Paralleling of Regulators for Higher Output Current R1 0.15 VIN > 2.9V + IN OUT LT3060 C1 2.2µF SHDN ADJ R8 1.91k 1% R9 604 1% C2 4.7µF 2.5V 200mA GND REF/BYP C3 1nF R2 0.15 IN OUT LT3060 SHDN SHDN ADJ R6 1.74k 1% R7 604 1% GND REF/BYP C4 1nF R3 200 R4 200 3 + – 7 LT1637 4 6 R5 1k 2 C5 10nF 3060 TA03 3060fa 22 LT3060 Series package DescripTion (Reference LTC DWG # 05-08-1719 Rev A) DC Package 8-Lead Plastic DFN (2mm × 2mm) 0.70 ±0.05 2.55 ±0.05 1.15 ±0.05 0.64 ±0.05 (2 SIDES) PACKAGE OUTLINE 0.25 ± 0.05 0.45 BSC 1.37 ±0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED R = 0.05 TYP 2.00 ±0.10 (4 SIDES) R = 0.115 TYP 5 8 0.40 ± 0.10 PIN 1 NOTCH R = 0.20 OR 0.25 × 45° CHAMFER (DC8) DFN 0409 REVA PIN 1 BAR TOP MARK (SEE NOTE 6) 0.64 ± 0.10 (2 SIDES) 4 0.200 REF 0.75 ±0.05 1.37 ±0.10 (2 SIDES) 0.00 – 0.05 0.23 ± 0.05 0.45 BSC 1 BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3060fa 23 LT3060 Series package DescripTion (Reference LTC DWG # 05-08-1637) 2.90 BSC (NOTE 4) TS8 Package 8-Lead Plastic TSOT-23 0.52 MAX 0.65 REF 1.22 REF 3.85 MAX 2.62 REF 1.4 MIN 2.80 BSC 1.50 – 1.75 (NOTE 4) PIN ONE ID RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.65 BSC 0.80 – 0.90 0.22 – 0.36 8 PLCS (NOTE 3) 0.20 BSC DATUM ‘A’ 1.00 MAX 0.01 – 0.10 0.30 – 0.50 REF NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 0.09 – 0.20 (NOTE 3) 1.95 BSC TS8 TSOT-23 0802 3060fa 24 LT3060 Series revision hisTory REV A DATE 07/10 DESCRIPTION Added fixed voltage options for 1.2V, 1.5V, 1.8V, 2.5V, 3.3V and 5V PAGE NUMBER 1-26 3060fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 25 LT3060 Series Typical applicaTion 12V Low Noise Regulator VIN = 13V OUTPUT VOLTAGE DEVIATION 50mV/DIV IN VIN 13V TO 45V 1µF LT3060 SHDN OUT 2.37M 1% ADJ 124k 1% CFF 10nF VOUT 12V AT 100mA 30µVRMS NOISE 10µF CFF = 0 GND REF/BYP 10nF CFF = 10nF 3060 TA04 LOAD ∆IL = 10mA TO 100mA CURRENT 100mA/DIV 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 TIME (ms) 3060 TA04b relaTeD parTs PART NUMBER LT1761 LT1762 LT1763 LT1764/ LT1764A LT1962 LT1963/ LT1963A LT1964 LT1965 LT3008 LT3009 LT3050 DESCRIPTION 100mA, Low Noise LDO 150mA, Low Noise LDO 500mA, Low Noise LDO 3A, Fast Transient Response, Low Noise LDO 300mA, Low Noise LDO 1.5A Low Noise, Fast Transient Response LDO 200mA, Low Noise, Negative LDO 1.1A, Low Noise, Low Dropout Linear Regulator 20mA, 45V, 3µA IQ Micropower LDO 20mA, 3µA IQ Micropower LDO COMMENTS 300mV Dropout Voltage, Low Noise: 20µVRMS , VIN = 1.8V to 20V, ThinSOT Package 300mV Dropout Voltage, Low Noise: 20µVRMS , VIN = 1.8V to 20V, MS8 Package 300mV Dropout Voltage, Low Noise: 20µVRMS , VIN = 1.8V to 20V, SO8 Package 340mV Dropout Voltage, Low Noise: 40µVRMS , VIN = 2.7V to 20V, TO-220 and DD Packages, LT1764A Version Stable Also with Ceramic Capacitors 270mV Dropout Voltage, Low Noise: 20µVRMS , VIN = 1.8V to 20V, MS8 Package 340mV Dropout Voltage, Low Noise: 40µVRMS , VIN = 2.5V to 20V, LT1963A Version Stable with Ceramic Capacitors; TO-220, DD, SOT-223 and SO8 Packages 340mV Dropout Voltage, Low Noise 30µVRMS , VIN = –1.8V to –20V, ThinSOT Package 290mV Dropout Voltage, Low Noise: 40µVRMS , VIN: 1.8V to 20V, VOUT: 1.2V to 19.5V, Stable with Ceramic Capacitors; TO-220, DD-Pak, MSOP and 3mm × 3mm DFN Packages 300mV Dropout Voltage, Low IQ: 3µA, VIN = 2V to 45V, VOUT = 0.6V to 39.5V; ThinSOT and 2mm × 2mm DFN-6 Packages 280mV Dropout Voltage, Low IQ: 3µA, VIN = 1.6V to 20V, ThinSOT and SC70 Packages 100mA, Low Noise Linear Regulator with 340mV Dropout Voltage, Low Noise: 30µVRMS , VIN: 1.6V to 45V, VOUT: 0.6V to 44.5V, Programmable Precision Current Limit: ±5%, Programmable Minimum IOUT Monitor, Output Current Precision Current Limit and Diagnostic Monitor, Fault Indicator, Reverse Protection; 12-Lead 2mm × 3mm DFN and MSOP Packages. Functions. 1.1A, Parallelable, Low Noise, Low Dropout Linear Regulator 300mV Dropout Voltage (2-Supply Operation), Low Noise: 40µVRMS , VIN : 1.2V to 36V, VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor VOUT Set; Directly Parallelable (No Op Amp Required), Stable with Ceramic Capacitors; TO-220, SOT-223, MSOP and 3mm × 3mm DFN Packages; LT3080-1 Version Has Integrated Internal Ballast Resistor Outputs May Be Paralleled for Higher Output, Current or Heat Spreading, Wide Input Voltage Range: 1.2V to 40V Low Value Input/Output Capacitors Required: 0.22μF Single Resistor Sets , Output Voltage Initial Set Pin Current Accuracy: 1%, Low Output Noise: 40μVRMS (10Hz to 100kHz) Reverse-Battery Protection, Reverse-Current Protection; 8-Lead SOT-23, 3-Lead SOT-223 and 8-Lead 3mm × 3mm DFN Packages 275mV Dropout Voltage (2-Supply Operation), Low Noise: 40µVRMS, VIN: 1.2V to 36V, VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor VOUT Set, Directly Parallelable (No Op Amp Required), Stable with Ceramic Capacitors; MS8E and 2mm × 3mm DFN-6 Packages Programmable 2-Terminal Current Source, Maximum Output Current: 200mA Wide Input Voltage Range: 1.2V to 40V, Resistor Ratio Sets Output Current Initial Set Pin Current Accuracy: 1%, Current Limit and Thermal Shutdown Protection Reverse-Voltage Protection, Reverse-Current Protection; 8-Lead SOT-23, 3-Lead SOT-223 and 8-Lead 3mm × 3mm DFN Packages 3060fa LT REV A 0710 • PRINTED IN USA LT3080/ LT3080-1 LT3082 200mA, Parallelable, Single Resistor, Low Dropout Linear Regulator LT3085 500mA, Parallelable, Low Noise, Low Dropout Linear Regulator 200mA 2-Terminal Programmable Current Source LT3092 26 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com  LINEAR TECHNOLOGY CORPORATION 2010