LTC1164-6CSW

LTC1164-6 Low Power 8th Order Pin Selectable Elliptic or Linear Phase Lowpass Filter FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTIO 8th Order Pin Selectable Elliptic or Bessel Filter 4mA Supply Current with ± 5V Supplies 64dB Attenuation at 1.44 fCUTOFF (Elliptic Response) fCUTOFF Up to 30kHz (50:1 fCLK to fCUTOFF Ratio) 110µVRMS Wideband Noise with ± 5V Supplies Operates at Single 5V Supply with 1VRMS Input Range Operates Up to ± 8V Supplies TTL/CMOS Compatible Clock Input No External Components Available in 14-Pin Dip and 16-Pin SO Wide Packages The LTC®1164-6 is a monolithic 8th order elliptic lowpass filter featuring clock-tunable cutoff frequency and low power supply current. Low power operation is achieved without compromising noise or distortion performance. At ± 5V supplies the LTC1164-6 uses only 4mA supply current while keeping wideband noise below 110µVRMS. With a single 5V supply, the LTC1164-6 can provide up to 10kHz cutoff frequency and 80dB signal-to-noise ratio while consuming only 2.5mA. The LTC1164-6 provides an elliptic lowpass rolloff with stopband attenuation of 64dB at 1.44 fCUTOFF and an fCLKto-fCUTOFF ratio of 100:1 (Pin 10 to V –). For a ratio of 100:1, fCUTOFF can be clock-tuned up to 10kHz. For a fCLK-tofCUTOFF ratio of 50:1 (Pin 10 to V +), the LTC1164-6 provides an elliptic lowpass filter with fCUTOFF frequencies up to 20kHz. When Pin 10 is connected to ground, the LTC1164-6 approximates an 8th order linear phase response with 65dB attenuation at 4.5 f – 3dB and fCLK / f – 3dB ratio of 160:1. The LTC1164-6 is pin compatible with the LTC1064-1. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. APPLICATIO S ■ ■ ■ Antialiasing Filters Battery-Operated Instruments Telecommunication Filters TYPICAL APPLICATIO 10kHz Anti-Aliasing Elliptic Filter NC VIN 1 2 3 8V 4 5 6 7 LTC1164-6 14 13 12 11 10 9 8 1164-6 TA01 0 NC –8V GAIN (dB) –10 –20 –30 –40 –50 –60 –70 –80 1 10 FREQUENCY (kHz) 100 1164-6 TA02 CLK = 1MHz –8V VOUT WIDEBAND NOISE = 115µVRMS NOTE: THE CONNECTION FROM PIN 7 TO PIN 14 SHOULD BE MADE UNDER THE PACKAGE. THE POWER SUPPLIES SHOULD BE BYPASSED BY A 0.1µF CAPACITOR AS CLOSE TO THE PACKAGE AS POSSIBLE. U Frequency Response 11646fa U U 1 LTC1164-6 ABSOLUTE AXI U RATI GS (Note 1) Operating Temperature Range LTC1164-6C ...................................... – 40°C to 85°C LTC1164-6M (OBSOLETE) .............. – 55°C to 125°C Storage Temperature Range ................ – 65°C to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C Total Supply Voltage (V + to V –) ............................. 16V Input Voltage (Note 2) ......... (V ++ 0.3V) to (V – – 0.3V) Output Short-Circuit Duration ......................... Indefinite Power Dissipation ............................................. 400mW Burn-In Voltage ...................................................... 16V PACKAGE/ORDER I FOR ATIO TOP VIEW NC VIN GND V+ GND LP6 CONNECT 1 1 2 3 4 5 6 7 14 CONNECT 2 13 NC 12 V – 11 CLK 10 ELL/BESS 9 8 VOUT NC ORDER PART NUMBER LTC1164-6CN NC 1 VIN 2 GND 3 V+ 4 GND 5 NC 6 LP6 7 CONNECT 1 8 N PACKAGE 14-LEAD PDIP TJMAX = 110°C, θJA = 65°C/W J PACKAGE 14-LEAD CERDIP TJMAX = 150°C, θJA = 65°C/W OBSOLETE PACKAGE Consider the N14 Package as an Alternate Source LTC1164-6CJ LTC1164-6MJ Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. The ● denotes specifications that apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VS = ± 7.5V, RL = 10k, TA = 25°C, fCLK = 400kHz, TTL or CMOS level (maximum clock rise or fall time ≤ 1µs) and all gain measurements are referenced to passband gain, unless otherwise specified. (fCLK / fCUTOFF) = 4kHz at 100:1 and 8kHz at 50:1. PARAMETER Passband Gain 0.1Hz to 0.25 fCUTOFF (Note 4) Passband Ripple with VS = Single 5V Gain at 0.50 fCUTOFF (Note 3) Gain at 0.90 fCUTOFF (Note 3) Gain at 0.95 fCUTOFF (Note 3) Gain at fCUTOFF (Note 3) Gain at 1.44 fCUTOFF (Note 3) Gain at 2.0 fCUTOFF (Note 3) Gain with fCLK = 20kHz Gain with VS = ± 2.375V Input Frequency Range (Tables 3, 4) CONDITIONS fIN = 1kHz, (fCLK / fC) = 100:1 1Hz to 0.8 fC (Table 2) fIN = 2kHz, (fCLK / fC) = 100:1 fIN = 3.6kHz, (fCLK / fC) = 100:1 fIN = 3.8kHz, (fCLK / fC) = 100:1 fIN = 4kHz, (fCLK / fC) = 100:1 fIN = 8kHz, (fCLK / fC) = 50:1 fIN = 5.76kHz, (fCLK / fC) = 100:1 fIN = 8kHz, (fCLK / fC) = 100:1 fIN = 200Hz, (fCLK / fC) = 100:1 fIN = 400kHz, fIN = 2kHz, (fCLK / fC) = 100:1 fIN = 400kHz, fIN = 4kHz, (fCLK / fC) = 100:1 (fCLK / fC) = 100:1 (fCLK / fC) = 50:1 ● ● ● ● ● ● ● ● ELECTRICAL CHARACTERISTICS 2 U U W WW U W TOP VIEW 16 CONNECT 2 15 NC 14 V– ORDER PART NUMBER LTC1164-6CSW 13 NC 12 CLK 11 ELL/BESS 10 NC 9 SW PACKAGE 16-LEAD PLASTIC SO VOUT TJMAX = 110°C, θJA = 85°C/W MIN – 0.50 – 0.45 – 0.75 –1.40 – 3.70 – 3.10 –75 – 75 – 3.70 – 0.50 – 3.50 TYP – 0.15 0.1 to – 0.3 – 0.10 – 0.30 – 0.70 – 2.70 – 2.10 – 64 – 64 – 2.70 – 0.10 – 2.50 0 – 25°C ● ● ● ● ELECTRICAL CHARACTERISTICS MIN TYP 1.5 1.0 1.0 500 200 115 ± 5% 100 ± 5% 75 ±1.50 ± 4.10 ± 5.90 ± 100 ±100 2.5 4.5 7.0 MAX UNITS MHz MHz MHz µVRMS µVRMS µVRMS µVRMS kΩ V V V mV µV/°C mA mA mA mA mA mA V Clock Feedthrough Wideband Noise Input Impedance Output DC Voltage Swing 45 ±1.25 ± 3.70 ± 5.40 110 Output DC Offset Output DC Offset Tempco Power Supply Current ±160 4.0 4.5 7.0 8.0 11.0 12.5 ±8 ● VS = ± 7.5V, TA > 25°C ● Power Supply Range Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. ± 2.375 Note 2: Connecting any pin to voltages greater than V + or less than V – may cause latch-up. It is recommended that no sources operating from external supplies be applied prior to power-up of the LTC1164-6. Note 3: All gains are measured relative to passband gain. Note 4: The cutoff frequency of the filter is abbreviated as fCUTOFF or fC. TYPICAL PERFOR A CE CHARACTERISTICS Stopband Gain vs Frequency (Elliptic Response) 10 0 –10 –20 VS = ± 5V fCLK = 500kHz fC = 5kHz (fCLK /fC) = 100:1 (PIN 10 AT V – ) TA = 25°C 10 0 –10 –20 VS = ± 5V fCLK = 250kHz (fCLK /fC) = 50:1 (PIN 10 AT V +) TA = 25°C WITH EXTERNAL SINGLE POLE LOWPASS RC FILTER (f – 3dB = 10kHz) GAIN (dB) GAIN (dB) –30 –40 –50 –60 –70 –80 –90 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (kHz) 1164-6 G01 UW Stopband Gain vs Frequency (Elliptic Response) –30 –40 –50 –60 –70 –80 –90 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (kHz) 1164-6 G02 11646fa 3 LTC1164-6 TYPICAL PERFOR A CE CHARACTERISTICS Stopband Gain vs Frequency (Linear Phase Response) 10 0 –10 –20 GAIN (dB) GAIN (dB) –30 –40 –50 –60 –70 –80 –90 2 6 10 14 18 22 26 30 34 38 42 FREQUENCY (kHz) 1164-6 G03 Passband Gain vs Frequency 0.8 0.4 0 –0.4 GAIN (dB) –0.8 –1.2 –1.6 –2.0 –2.4 –2.8 0.4 GAIN (dB) VS = ± 5V fCLK = 500kHz fC = 5kHz (fCLK /fC) = 100:1 (PIN 10 AT V – ) TA = 25°C (10 REPRESENTATIVE UNITS) 1.0 2.2 2.8 1.6 FREQUENCY (kHz) 3.4 4.0 –2 –3 –4 –5 –6 –7 1 VS = ±5V fCLK = 800kHz fC = 5kHz (fCLK /fC) = 160:1 (PIN 10 AT GND) TA = 25°C GAIN GAIN (dB) Passband vs Frequency and fCLK 2.0 1.5 1.0 0.5 VS = ± 5V (fCLK /fC) = 100:1 (PIN 10 AT V – ) TA = 25°C A. fCLK = 400kHz fCUTOFF = 4kHz B. fCLK = 600kHz fCUTOFF = 6kHz C. fCLK = 800kHz fCUTOFF = 8kHz D. fCLK = 1MHz fCUTOFF = 10kHz GAIN (dB) GAIN (dB) 0 – 0.5 –1.0 –1.5 –2.0 –2.5 – 3.0 1 A B C D 5 INPUT FREQUENCY (kHz) 4 UW 1164-6 G05 1164-6 G06 Passband Gain and Phase vs Frequency A. RESPONSE WITHOUT EXTERNAL RC FILTER B. RESPONSE WITH AN EXTERNAL SINGLE POLE LOWPASS RC FILTER (f – 3dB AT 10kHz) 2.0 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 VS = ± 5V fCLK = 500kHz fC = 5kHz (fCLK /fC) = 100:1 (PIN 10 AT V – ) TA = 25°C 1 2 4 3 FREQUENCY (kHz) 5 1164-6 G04 0 –45 –90 –135 VS = ± 5V fCLK = 800kHz fC = 5kHz (fCLK /fC) = 160:1 (PIN 10 AT GND) TA = 25°C PHASE (DEG) –180 –225 –270 –315 –360 –405 –450 A B –2.5 –3.0 Passband Gain and Phase vs Frequency (Linear Phase Response) 3 2 1 0 –1 PHASE 0 –30 –60 –90 PHASE (DEG) Maximum Passband over Temperature 0.4 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 –1.2 –1.4 –1.6 1 VS = ± 5V fCLK = 1MHz fC = 10kHz (fCLK /fC) = 100:1 (PIN 10 AT V – ) 5 FREQUENCY (kHz) 10 1164-6 G07 A B C A. TA = 125°C B. TA = 85°C D. TA = – 40°C –120 –150 –180 –210 –240 –270 –300 2 4 3 FREQUENCY (kHz) 5 1164-6 G11 Passband Gain and Phase vs Frequency and fCLK 3 2 1 0 –1 –2 –3 –4 –5 –6 –7 –8 –9 10 0 –45 A B PHASE A B VS = ± 5V fCLK = 250kHz fC = 5kHz (fCLK /fC) = 50:1 (PIN 10 AT V – ) TA = 25°C 1 2 3 4 FREQUENCY (kHz) 5 1164-6 G08 –90 –135 –180 –225 –270 –315 –360 –405 –450 –495 –540 A. RESPONSE WITHOUT EXTERNAL SINGLE POLE RC FILTER B. RESPONSE WITH AN EXTERNAL SINGLE POLE LOWPASS RC FILTER (f – 3dB AT 10kHz) PHASE (DEG) 11646fa LTC1164-6 TYPICAL PERFOR A CE CHARACTERISTICS Passband vs Frequency and fCLK 2.0 1.5 1.0 0.5 GAIN (dB) GAIN (dB) 0 –0.5 –1.0 –1.5 –2.0 –2.5 –3.0 1 VS = ± 8V (fCLK /f C) = 50:1 (PIN 10 AT V +) TA = 25°C 10 FREQUENCY (kHz) 30 1164-6 G09 Group Delay vs Frequency (Linear Phase Response) 250 fCLK = 800kHz (fCLK /fC) = 160:1 fC = 5kHz GROUP DELAY (µs) 200 GROUP DELAY (µs) 150 B 400 300 200 100 VS = ±5V fC = 5kHz TA = 25°C 1 4 2 3 FREQUENCY (kHz) 5 1164-6 G12 THD + NOISE (dB) 100 50 0 1 2 3 45678 FREQUENCY (kHz) 9 10 11 1164-6 G22 THD + Noise vs Frequency (Elliptic Response) –40 –45 –50 THD + NOISE (dB) – 40 THD + NOISE (dB) THD + NOISE (dB) –55 –60 –65 –70 –75 –80 –85 –90 1 VS = ± 5V, VIN = 1VRMS, fCLK = 500kHz, fC = 10kHz, (fCLK /fC) = 50:1, TA = 25°C, WITH EXTERNAL RC LOWPASS FILTER (f – 3dB = 20kHz) (5 REPRESENTATIVE UNITS) 5 FREQUENCY (kHz) UW A Maximum Passband over Temperature A. fCLK = 250kHz fCUTOFF = 5kHz B. fCLK = 500kHz fCUTOFF = 10kHz C. fCLK = 1MHz fCUTOFF = 20kHz 2.0 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 –2.5 –3.0 2 4 6 8 10 12 14 16 18 20 22 FREQUENCY (kHz) 1164-6 G10 TA = 70°C TA = – 40°C VS = SINGLE 5V (fCLK /fC) = 50:1 GND = 2V WITH EXTERNAL RC LOWPASS FILTER (f – 3dB = 40kHz) B C Group Delay vs Frequency (Elliptic Response) 700 600 500 A. fCLK = 250kHz, (fCLK /fC) = 50:1 WITH EXTERNAL RC LOWPASS FILTER (f C = 10kHz) B. fCLK = 500kHz (fCLK /fC) = 100:1 – 40 –45 THD + Noise vs Frequency (Elliptic Response) VS = ± 5V, VIN = 1VRMS (20k RESISTOR PIN 14 TO V – ) fCLK = 500kHz, fC = 5kHz (fCLK /fC) = 100:1, TA = 25°C (5 REPRESENTATIVE UNITS) A – 50 –55 –60 –65 –70 –75 –80 –85 –90 1 0 3 2 FREQUENCY (kHz) 4 5 1164-6 G13 THD + Noise vs Frequency (Elliptic Response) – 40 THD + Noise vs Frequency (Linear Phase Response) –45 – 50 –55 –60 –65 –70 –75 –80 –85 VS = ± 5V VIN = 1VRMS fCLK = 800kHz fC = 5kHz (fCLK /fC) = 160:1 TA = 25°C –45 – 50 –55 –60 –65 –70 –75 –80 –85 VS = SINGLE 5V, VIN = 0.7VRMS fCLK = 500kHz, fC = 5kHz, (fCLK /fC) = 100:1, TA = 25°C (5 REPRESENTATIVE UNITS) 10 1164-6 G14 –90 0.5 1 FREQUENCY (kHz) 5 1164-6 G16 –90 1 3 2 FREQUENCY (kHz) 4 5 1164-6 G23 11646fa 5 LTC1164-6 TYPICAL PERFOR A CE CHARACTERISTICS THD + Noise vs RMS Input (Elliptic Response) – 40 –45 – 50 (fCLK /fC) = 100:1 OR 50:1 fIN = 1kHz, TA = 25°C –40 –45 –50 THD + NOISE (dB) THD + NOISE (dB) CURRENT (mA) –55 –60 –65 –70 –75 –80 –85 –90 0.1 1 INPUT (VRMS) 1164-6 G17 VS = ± 5V VS = ± 7.5V Transient Response 2V/DIV 2V/DIV VS = ± 7.5V, VIN = ±3V 100Hz SQUARE WAVE fCLK = 500kHz, (fCLK /f C) = 100:1, fCUTOFF = 5kHz ELLIPTIC RESPONSE PI FU CTIO S (14-Lead Dual-In-Line Package) NC (Pins 1, 8, 13): Pins 1, 8, and 13 are not connected to any internal circuit point on the device and should preferably be tied to analog ground. VIN (Pin 2): The input pin is connected internally through a 50k resistor tied to the inverting input of an op amp. GND (Pins 3, 5): The filter performance depends on the quality of the analog signal ground. For either dual or single supply operation, an analog ground plane surrounding the package is recommended. The analog ground plane should be connected to any digital ground at a single point. For dual supply operation, Pins 3 and 5 should be connected to the analog ground plane. For single supply operation Pins 3 and 5 should be biased at 1/2 supply and they should be bypassed to the analog ground plane with 6 UW 5 THD + Noise vs RMS Input for Single 5V (Elliptic Response) 12 (fCLK /fC) = 100:1 OR 50:1 fIN = 1kHz, TA = 25°C A B 11 10 9 8 7 6 5 4 3 2 A. GND = 2.5V B. GND = 2V 1 INPUT (VRMS) 1164-6 G18 Power Supply Current vs Power Supply Voltage –55°C 25°C 125°C –55 –60 –65 –70 –75 –80 –85 –90 0.1 1 0 2 0 1 2345678 POWER SUPPLY (V + OR V –) 9 10 1164-6 G19 Transient Response 1ms/DIV 1164-6 G20 1ms/DIV 1164-6 G21 VS = ± 7.5V, VIN = ±3V 100Hz SQUARE WAVE fCLK = 800kHz, (fCLK /f C) = 160:1, fCUTOFF = 5kHz LINEAR PHASE RESPONSE U U U at least a 1µF capacitor (Figure 2). For single 5V operation at the highest fCLK of 1MHz, Pins 3 and 5 should be biased at 2V. This minimizes passband gain and phase variations (see Typical Performance Characteristics curves: Maximum Passband for Single 5V, 50:1; and THD + Noise vs RMS Input for Single 5V, 50:1). V+ (Pins 4, 12):The V+ (Pin 4) and the V – (Pin 12) should be bypassed with a 0.1µF capacitor to an adequate analog ground. The filter’s power supplies should be isolated from other digital or high voltage analog supplies. A low noise linear supply is recommended. Using a switching power supply will lower the signal-to-noise ratio of the filter. The supply during power-up should have a slew rate less than 1V/µs. When V+ is applied before V – and V – 11646fa LTC1164-6 PI FU CTIO S could go above ground, a signal diode must be used to clamp V. Figures 1 and 2 show typical connections for dual and single supply operation. V– 1 VIN V+ 2 3 4 5 0.1µF 6 7 LTC1164-6 14 13 12 11 10 9 8 GND + DIGITAL SUPPLY 1k CLOCK SOURCE * OPTIONAL Figure 1. Dual Supply Operation for fCLK/fCUTOFF = 100:1 1 VIN V+ 0.1µF 10k 2 3 4 5 6 7 LTC1164-6 14 13 12 11 10 9 8 GND + DIGITAL SUPPLY 1k CLOCK SOURCE 10k + 1µF VOUT 1164-6 F02 Figure 2. Single Supply Operation for fCLK/fCUTOFF = 100:1 Table 1. Clock Source High and Low Threshold Levels POWER SUPPLY Dual Supply = ± 7.5V Dual Supply = ± 5V Dual Supply = ± 2.5V Single Supply = 12V Single Supply = 5V HIGH LEVEL ≥ 2.18V ≥ 1.45V ≥ 0.73V ≥ 7.80V ≥ 1.45V LOW LEVEL ≤ 0.5V ≤ 0.5V ≤ – 2.0V ≤ 6.5V ≤ 0.5V V– (Pins 7, 14): Pins 7 and 14 should be connected together. In a printed circuit board the connection should be done under the IC package through a short trace surrounded by the analog ground plane. VOUT (Pins 9, 6): Pin 9 is the specified output of the filter; it can typically source or sink 1mA. Driving coaxial cables or resistive loads less than 20k will degrade the total harmonic distortion of the filter. When evaluating the device’s distortion an output buffer is required. A noninverting Figure 3. Buffer for Filter Output 11646fa + 1k – U U U (14-Lead Dual-In-Line Package) buffer, Figure 3,can be used provided that its input common mode range is well within the filter’s output swing. Pin 6 is an intermediate filter output providing an unspecified 6th order lowpass filter. Pin 6 should not be loaded. ELLIPTIC/LINEAR PHASE (Pin 10): The DC level at this pin selects the desired filter response, elliptic or linear phase and determines the ratio of the clock frequency to the cutoff frequency of the filter. Pin 10 connected to V – provides an elliptic lowpass filter with clock-to-fCUTOFF ratio of 100:1. Pin 10 connected to analog ground provides a linear phase lowpass filter with a clock- to-f–3dB ratio of 160:1 and a transient response overshoot of 1%. When Pin 10 is connected to V+ the clock-to-fCUTOFF ratio is 50:1 and the filter response is elliptic. Bypassing Pin 10 to analog ground reduces the output DC offsets. If the DC level at Pin 10 is switched mechanically or electrically at slew rates greater than 1V/µs while the device is operating, a 10k resistor should be connected between Pin 10 and the DC source. CLK (Pin 11): Any TTL or CMOS clock source with a square-wave output and 50% duty cycle (±10%) is an adequate clock source for the device. The power supply for the clock source should not be the filter’s power supply. The analog ground for the filter should be connected to clock’s ground at a single point only. Table 1 shows the clock’s low and high level threshold value for a dual or single supply operation. A pulse generator can be used as a clock source provided the high level ON time is greater than 0.5µs. Sine waves are not recommended for clock input frequencies less than 100kHz, since excessively slow clock rise or fall times generate internal clock jitter (maximum clock rise or fall time ≤ 1µs). The clock signal should be routed from the right side of the IC package to avoid coupling into any input or output analog signal path. A 1k resistor between clock source and Pin 11 will slow down the rise and fall times of the clock to further reduce charge coupling, Figures 1 and 2. * 0.1µF VOUT 1164-6 F01 LT1006, fC < 5kHz LT1200, fC > 5kHz 1164-6 F03 7 LTC1164-6 APPLICATI S I FOR ATIO Passband Response The passband response of the LTC1164-6 is optimized for a fCLK/ fCUTOFF ratio of 100:1. Minimum passband ripple occurs from 1Hz to 80% of fCUTOFF. Athough the passband of the LTC1164-6 is optimized for ratio fCLK / fCUTOFF of 100:1, if a ratio of 50:1 is desired, connect a single pole lowpass RC (f –3dB = 2 fCUTOFF) at the output of the filter. The RC will make the passband gain response as flat as the 100:1 case. If the RC is omitted, and clock frequencies are below 500kHz the passband gain will peak by 0.4dB at 90% fCUTOFF. Table 2. Typical Passband Ripple with Single 5V Supply (fCLK/fC) = 100:1, GND = 2V, 30kHz, Fixed Single Pole, Lowpass RC Filter at Pin 9 (See Typical Applications) PASSBAND FREQUENCY PASSBAND GAIN (REFERENCED TO 0dB) fCUTOFF = 1kHz fCUTOFF = 10kHz TA = 25°C TA = 0°C TA = 25°C TA = 70°C (dB) (dB) (dB) (dB) 0.00 0.00 0.00 0.00 – 0.02 0.00 0.01 0.01 – 0.05 – 0.01 – 0.01 0.01 – 0.10 – 0.02 – 0.02 0.02 – 0.13 – 0.03 – 0.01 0.03 – 0.15 – 0.01 0.01 0.05 – 0.18 – 0.01 0.01 0.07 – 0.25 – 0.08 – 0.05 0.02 – 0.39 – 0.23 – 0.18 – 0.05 – 2.68 – 2.79 – 2.74 – 2.68 % of fCUTOFF 10 20 30 40 50 60 70 80 90 fCUTOFF The gain peaking can approximate a sin χ/χ correction for some applications. (See Typical Performance Characteristics curve, Passband vs Frequency and fCLK at fCLK /fC = 50:1.) When the LTC1164-6 operates with a single 5V supply and its cutoff frequency is clock-tuned to 10kHz, an output single pole RC filter can also help maintain outstanding passband flatness from 0°C to 70°C. Table 2 shows details. Clock Feedthrough Clock feedthrough is defined as, the RMS value of the clock frequency and its harmonics that are present at the filter’s output (Pin 9). The clock feedthrough is tested with the input (Pin 2) grounded and, it depends on PC board layout and on the value of the power supplies. With proper layout techniques the values of the clock feedthrough are shown in Table 3. 8 U Table 3. Clock Feedthrough VS ± 2.5V ± 5V ± 7.5V 50:1 60µVRMS 100µVRMS 150µVRMS 100:1 60µVRMS 200µVRMS 500µVRMS Note: The clock feedthrough at ± 2.5V supplies is imbedded in the wideband noise of the filter. (The clock signal is a square wave.) W U UO Any parasitic switching transients during the rise and fall edges of the incoming clock are not part of the clock feedthrough specifications. Switching transients have frequency contents much higher than the applied clock; their amplitude strongly depends on scope probing techniques as well as grounding and power supply bypassing. The clock feedthrough, if bothersome, can be greatly reduced by adding a simple R/C lowpass network at the output of the filter (Pin 9). This R/C will completely eliminate any switching transient. Wideband Noise The wideband noise of the filter is the total RMS value of the device’s noise spectral density and it is used to determine the operating signal-to-noise ratio. Most of its frequency contents lie within the filter passband and it cannot be reduced with post filtering. For instance, the LTC1164-6 wideband noise at ± 2.5V supply is 100µVRMS, 90µVRMS of which have frequency contents from DC up to the filter’s cutoff frequency. The total wideband noise (µVRMS) is nearly independent of the value of the clock. The clock feedthrough specifications are not part of the wideband noise. Speed Limitations The LTC1164-6 optimizes AC performance versus power consumption. To avoid op amp slew rate limiting at maximum clock frequencies, the signal amplitude should be kept below a specified level as shown on Table 4. Aliasing Aliasing is an inherent phenomenon of sampled data systems and it occurs when input frequencies close to the sampling frequency are applied. For the LTC1164-6 case, an input signal whose frequency is in the range of fCLK ±4%, will be aliased back into the filter’s passband. If, for instance, an LTC1164-6 operating with a 100kHz clock 11646fa LTC1164-6 APPLICATI S I FOR ATIO and 1kHz cutoff frequency receives a 98.5kHz, 10mVRMS input signal, a 1.5kHz, 10µVRMS alias signal will appear at its output. When the LTC1164-6 operates with a clock-tocutoff frequency of 50:1, aliasing occurs at twice the clock frequency. Table 5 shows details. Table 4. Maximum VIN vs VS and fCLK POWER SUPPLY ± 7.5V MAXIMUM fCLK 1.5MHz 1MHz ≥ 1MHz 1MHz 1MHz 1MHz 1MHz MAXIMUM VIN 1VRMS (fIN > 35kHz) 3VRMS (fIN > 25kHz) 0.7VRMS (fIN > 250kHz) 2.5VRMS (fIN > 25kHz) 0.5VRMS (fIN > 100kHz) 0.7VRMS (fIN > 25kHz) 0.5VRMS (fIN > 100kHz) ± 5V Single 5V Table 5. Aliasing (fCLK = 100kHz) INPUT FREQUENCY OUTPUT LEVEL (VIN = 1VRMS) (Relative to Input) (kHz) (dB) fCLK/fC = 100:1, fCUTOFF = 1kHz 96 (or 104) 97 (or 103) 98 (or 102) 98.5 (or 101.5) 99 (or 101) 99.5 (or 100.5) fCLK/fC = 50:1, fCUTOFF = 2kHz 192 (or 208) 194 (or 206) 196 (or 204) 198 (or 202) 199 (or 201) 199.5(or 200.5) –75.0 – 68.0 – 65.0 – 60.0 – 3.2 – 0.5 – 76.0 – 68.0 – 63.0 – 3.4 – 1.3 – 0.9 OUTPUT FREQUENCY (Aliased Frequency) (kHz) 4.0 3.0 2.0 1.5 1.0 0.5 8.0 6.0 4.0 2.0 1.0 0.5 TYPICAL APPLICATI S 8th Order Elliptic Lowpass Filter (fCLK / fC) = 50:1 14 13 12 LTC1164-6 11 10 9 8 VOUT fCLK V+ V– 0.1µF R C V– 11646fa 1 VIN V+ 0.1µF 2 3 4 5 6 7 U Table 6. Transient Response of LTC Lowpass Filters DELAY TIME* (SEC) 0.50/fC 0.43/fC 0.43/fC 1.15/fC 1.20/fC 1.20/fC 0.80/fC RISE TIME** (SEC) 0.34/fC 0.34/fC 0.34/fC 0.36/fC 0.39/fC 0.39/fC 0.48/fC SETTLING OVERTIME*** SHOOT (SEC) (%) 0.80/fC 0.85/fC 1.15/fC 2.05/fC 2.20/fC 2.20/fC 2.40/fC 0.5 0 1 5 5 5 11 18 20 20 LOWPASS FILTER LTC1064-3 Bessel LTC1164-5 Linear Phase LTC1164-6 Linear Phase LTC1264-7 Linear Phase LTC1164-7 Linear Phase LTC1064-7 Linear Phase LTC1164-5 Butterworth 0.54/fC 4.30/fC LTC1164-6 Elliptic 0.85/fC 0.54/fC 4.50/fC LTC1064-4 Elliptic 0.90/fC LTC1064-1 Elliptic 0.85/fC 0.54/fC 6.50/fC * To 50% ± 5%, ** 10% to 90% ± 5%, *** To 1% ± 0.5% ts INPUT 90% OUTPUT 50% td 10% tr RISE TIME (tr) = 0.54 ± 5% fCUTOFF 4.3 SETTLING TIME (ts) = ± 5% f (TO 1% of OUTPUT) CUTOFF 0.85 TIME DELAY (td) = GROUP DELAY ≈ fCUTOFF (TO 50% OF OUTPUT) 1164-6 F04 W UO U UO Figure 4 V+ – LT ®1006 NOTES: 1. OPTIONAL OUTPUT BUFFER 1/2πRC = (2)(fCUTOFF) 2. PINS 1, 8, 13 CAN BE GROUNDED OR LEFT FLOATING 1164-6 TA06 + 9 LTC1164-6 TYPICAL APPLICATI 1 VIN V+ 0.1µF 2 3 4 5 6 7 LTC1164-6 8th Order Elliptic Lowpass Filter (fCLK / fC) = 100:1 14 13 12 11 10 9 8 1164-6 TA07 8th Order 20kHz Cutoff, Elliptic Filter Operating with a Single 5V Supply and Driving 1k, 1000pF Load 1 VIN 2 3 5V 0.1µF 10k 4 5 6 7 0.1µF 6.65k LTC1164-6 14 13 12 11 10 9 8 510pF 1164-6 TA09 R1 789Ω VIN C1 0.01µF 1 2 3 4 LTC1164-6 IC1 5V 0.1µF 15k 5 6 1µF + 10k 7 Gain vs Frequency 10 0 –10 THD + NOISE (dB) –20 GAIN (dB) –30 –40 –50 –60 –70 –80 –90 1 10 FREQUENCY (kHz) 30 1164-6 TA04 VS = SINGLE 5V IS = 5mA, 16TH ORDER ELLIPTIC LOWPASS fCLK = 540kHz fCUTOFF = 10kHz 10 UO S 8th Order Linear Phase Lowpass Filter (fCLK / fC) = 160:1 1 VIN V– 2 3 V+ 0.1µF VOUT 4 5 6 7 LTC1164-6 14 13 12 11 10 9 8 1164-6 TA08 V– fCLK 0.1µF fCLK 0.1µF VOUT 5V 5V NOTES: 1. TOTAL SUPPLY CURRENT IS = 4mA (EXCLUDING OUTPUT LOAD CURRENT) 2. FLAT PASSBAND UP TO 18kHz, f –3dB = 20kHz 3. THD + NOISE ≤ – 70dB, 1VP-P ≤ VIN ≤ 3VP-P, fIN = 1kHz 1k 5V fCLK = 1MHz 10k 51.1k 2 – + 7 LT1200 VOUT 1k 1000pF 3 4 Single 5V, 16th Order Lowpass Filter fCUTOFF = 10kHz 14 13 12 11 10 9 8 5V 5V 0.1µF 1 2 3 4 5 6 7 LTC1164-6 IC2 14 13 12 11 10 9 8 R2 7.89k 5V VOUT C2 0.001µF VS = SINGLE 5V, IS = 5mA TYP 16TH ORDER LOWPASS FILTER FIXED fCUTOFF, fCLK = 540kHz fCUTOFF = 10kHz (fCLK/fC) = 54:1 1/2πR1C1 = 1/2πR2C2 = 2fCUTOFF fCLK 1k 1164-6 TA03 THD + Noise vs Frequency –40 –45 –50 –55 –60 –65 –70 –75 –80 –85 –90 1 5 FREQUENCY (kHz) 10 1164-6 TA05 VS = SINGLE 5V IS = 5mA, 16TH ORDER ELLIPTIC LOWPASS VIN = 0.5VRMS fCLK = 540kHz fC = 10kHz 11646fa LTC1164-6 PACKAGE DESCRIPTION J Package 14-Lead CERDIP (Narrow .300 Inch, Hermetic) (Reference LTC DWG # 05-08-1110) CORNER LEADS OPTION (4 PLCS) .005 (0.127) MIN .840 (21.336) MAX 16 15 14 13 12 11 10 9 .045 – .065 (1.143 – 1.65) FULL LEAD OPTION .300 BSC (7.62 BSC) .008 – .018 (0.203 – 0.457) 0° – 15° NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS .300 – .325 (7.620 – 8.255) .008 – .015 (0.203 – 0.381) +.035 .325 –.015 +0.889 –0.381 .005 (0.127) .100 MIN (2.54) BSC ( 8.255 INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) NOTE: 1. DIMENSIONS ARE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U ) .023 – .045 (0.584 – 1.143) HALF LEAD OPTION .025 (0.635) RAD TYP 1 2 3 4 5 6 7 8 .220 – .310 (5.588 – 7.874) .200 (5.080) MAX .015 – .060 (0.380 – 1.520) .125 (3.175) MIN .045 – .065 (1.143 – 1.651) .014 – .026 (0.360 – 0.660) .100 (2.54) BSC J16 0801 OBSOLETE PACKAGE N Package 14-Lead PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) .770* (19.558) MAX 14 13 12 11 10 9 8 .255 ± .015* (6.477 ± 0.381) 1 .130 ± .005 (3.302 ± 0.127) .020 (0.508) MIN 2 3 4 5 6 7 .045 – .065 (1.143 – 1.651) .065 (1.651) TYP .120 (3.048) MIN .018 ± .003 (0.457 ± 0.076) N14 1103 11646fa 11 LTC1164-6 TYPICAL APPLICATION 8th Order Low Power, Clock-Tunable Elliptic Filter with Active RC Input Antialiasing Filter and Output Smoothing Filter C2 0.022µF R1 1.15k VIN C1 0.1µF C3 0.001µF R2 76.8k R3 5.62k fC = 1kHz ATTENUATION AT 10kHz = –48dB NOTES: 1. CLOCK-TUNABLE OVER ONE DECADE OF CUTOFF FREQUENCY 2. BOTH INPUT AND OUTPUT RC ACTIVE FILTERS ARE 0.1dB CHEBYSHEV FILTERS WITH 1kHz RIPPLE BANDWIDTH PACKAGE DESCRIPTION SW Package 16-Lead Plastic Small Outline (Wide .300 Inch) (Reference LTC DWG # 05-08-1620) .030 ±.005 TYP N .420 MIN 1 2 3 RECOMMENDED SOLDER PAD LAYOUT .005 (0.127) RAD MIN .291 – .299 (7.391 – 7.595) NOTE 4 .010 – .029 × 45° (0.254 – 0.737) 0° – 8° TYP .009 – .013 (0.229 – 0.330) NOTE 3 .016 – .050 (0.406 – 1.270) NOTE: 1. DIMENSIONS IN INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS 4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm) RELATED PARTS PART NUMBER LTC1069-1 LTC1069-6 DESCRIPTION Low Power, 8th Order Elliptic Lowpass Very Low Power 8th Order Elliptic Lowpass COMMENTS Operates from a Single 3.3V to ± 5V Supply Optimized for 3V/5V Single Supply Operation, Consumes 1mA at 3V 11646fa LT 0207 REV A • PRINTED IN USA 12 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● U U + – 1 2 3 V + 14 13 12 LTC1164-6 11 10 9 8 R1 16.9k R2 97.6k C2 0.001µF fCLK V– V– 0.1µF 1/2 LT1013 4 0.1µF 5 6 7 – 1/2 LT1013 VOUT + C1 0.0047µF 100Hz ≤ fC ≤ 1kHz 10kHz ≤ fCLK ≤ 100kHz fC = 1kHz ATTENUATION AT 10kHz = –30dB 1164-6 TA10 .050 BSC .045 ±.005 .398 – .413 (10.109 – 10.490) NOTE 4 16 15 14 13 12 11 10 9 N .325 ±.005 NOTE 3 .394 – .419 (10.007 – 10.643) N/2 N/2 1 2 3 4 5 6 7 8 .093 – .104 (2.362 – 2.642) .037 – .045 (0.940 – 1.143) .050 (1.270) BSC .004 – .012 (0.102 – 0.305) .014 – .019 (0.356 – 0.482) TYP S16 (WIDE) 0502 www.linear.com © LINEAR TECHNOLOGY CORPORATION 1993