LTC1349C

LTC1349 5V Low Power RS232 3-Driver/5-Receiver Transceiver with 2 Receivers Active in SHUTDOWN FEATURES s s s s s s s s DESCRIPTIO s s s Low Supply Current: 300µA Two Receivers Kept Alive in SHUTDOWN ESD Protection Over ±10kV Operates from a Single 5V Supply Uses Small Capacitors: 0.1µF Operates to 120k Baud Three-State Outputs Are High Impedance When Off Output Overvoltage Does Not Force Current Back into Supplies RS232 I/O Lines Can Be Forced to ± 25V Without Damage Pin Compatible with LT1137A and LT1237 Flowthrough Architecture The LTC1349 is a 3-driver/5-receiver RS232 transceiver with very low supply current. In the no load condition, the supply current is only 300µA. The charge pump only requires four 0.1µF capacitors. In SHUTDOWN mode, two receivers are kept alive and the supply current is 35µA. All RS232 outputs assume a high impedance state in SHUTDOWN and with the power off. The LTC1349 is fully compliant with all data rate and overvoltage RS232 specifications. The transceiver can operate up to 120k baud with a 2500pF, 3kΩ load. Both driver outputs and receiver inputs can be forced to ± 25V without damage, and can survive multiple ± 10kV ESD strikes. APPLICATI s s S Notebook Computers Palmtop Computers TYPICAL APPLICATI V+ C1 0.1µF C2 0.1µF DRIVER 1 OUT RX1 IN DRIVER 2 OUT RX2 IN RX3 IN RX4 IN DRIVER 3 OUT RX5 IN ON/OFF NC VCC 3-Drivers/5-Receivers with SHUTDOWN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LTC1349 28 27 26 25 24 23 22 21 20 19 18 17 16 15 C3 0.1µF DRIVER 1 IN RX1 OUT DRIVER 2 IN RX2 OUT RX3 OUT RX4 OUT DRIVER 3 IN RX5 OUT GND NC NC LTC1349 • TA01 Quiescent and SHUTDOWN Supply Current vs Temperature C4 0.1µF 1200 1000 QUIESCENT CURRENT (µA) 800 600 400 200 0 –40 QUIESCENT CURRENT SHUTDOWN CURRENT 60 50 SHUTDOWN CURRENT (µA) 40 30 20 10 V– 0 0 80 100 20 60 40 TEMPERATURE (°C) TEST CONDITION: VCC = 5V, ALL DRIVER INPUTS TIED TO VCC. –20 LTC1349 • TA02 U UO UO 1 LTC1349 ABSOLUTE AXI U RATI GS PACKAGE/ORDER I FOR ATIO TOP VIEW V+ 1 VCC 2 C1+ C1– 3 4 28 V – 27 C2 + 26 C2 – 25 DR1 IN 24 RX1 OUT 23 DR2 IN 22 RX2 OUT 21 RX3 OUT 20 RX4 OUT 19 DR3 IN 18 RX5 OUT 17 GND 16 NC 15 NC Supply Voltage (VCC) ................................................ 6V Input Voltage Driver ....................................... – 0.3V to V CC + 0.3V Receiver ............................................... – 25V to 25V On/Off Pin .................................. – 0.3V to VCC + 0.3V Output Voltage Driver .................................................... – 25V to 25V Receiver .................................... – 0.3V to VCC + 0.3V Short Circuit Duration V + ................................................................... 30 sec V – ................................................................... 30 sec Driver Output .............................................. Indefinite Receiver Output .......................................... Indefinite Operating Temperature Range Commercial (LTC1349C) ........................ 0°C to 70°C Industrial (LTC1349I) ........................ – 40°C to 85°C Storage Temperature Range ................ – 65°C to 150°C Lead Temperature (Soldering, 10 sec)................. 300°C ORDER PART NUMBER LTC1349CG LTC1349CN LTC1349CS LTC1349IG LTC1349IN LTC1349IS DR1 OUT 5 RX1 IN 6 DR2 OUT 7 RX2 IN 8 RX3 IN 9 RX4 IN 10 DR3 OUT 11 RX5 IN 12 ON/OFF 13 NC 14 N PACKAGE G PACKAGE 28-LEAD PLASTIC DIP 28-LEAD SSOP S PACKAGE 28-LEAD PLASTIC SOL TJMAX = 125°C, θJA = 96°C/W (G) TJMAX = 125°C, θJA = 56°C/W (N) TJMAX = 125°C, θJA = 85°C/W (S) Consult factory for Military Grade parts. DC ELECTRICAL CHARACTERISTICS PARAMETER Any Driver Output Voltage Swing Logic Input Voltage Level Logic Input Current Output Short-Circuit Current Output Leakage Current Any Receiver Input Voltage Thresholds Hysteresis Input Resistance Output Voltage Output Short-Circuit Current Output Leakage Current Power Supply Generator V + Output Voltage V – Output Voltage Supply Rise Time CONDITIONS 3k to GND VCC = 5V, C1 = C2 = C3 = C4 = 0.1µF, unless otherwise noted. MIN Positive Negative q q q q q q q q q q TYP 7.0 – 6.5 1.4 1.4 MAX UNITS V V V V µA µA mA µA V V V kΩ V V mA µA V V V V ms 5.0 – 5.0 2.0 Input Low Level (VOUT = High) Input High Level (VOUT = Low) VIN = 5V VIN = 0V VOUT = 0V SHUTDOWN, VOUT = ± 20V (Note 3) Input Low Threshold Input High Threshold – 10V ≤ VIN ≤ 10V Output Low, IOUT = – 1.6mA (VCC = 5V) Output High, IOUT = 160µA (VCC = 5V) Sinking Current, VOUT = VCC SHUTDOWN, 0 ≤ VOUT ≤ VCC (Note 3) IOUT = 0mA IOUT = 12mA IOUT = 0mA IOUT = – 12mA SHUTDOWN to Turn-On 0.8 5 –5 ±12 ± 10 0.8 0.1 3 3.5 – 15 1.3 1.7 0.4 5 0.2 4.8 – 40 1 8.0 7.5 – 8.0 – 7.0 0.2 ± 500 q q q 2.4 1.0 7 0.4 10 2 U W U U WW W LTC1349 DC ELECTRICAL CHARACTERISTICS VCC = 5V, C1 = C2 = C3 = C4 = 0.1µF, unless otherwise noted. PARAMETER Power Supply VCC Supply Current CONDITIONS No Load (All Drivers VIN = VCC)(Note 2), 0 ≤ TA ≤ 70°C No Load (All Drivers VIN = 0V)(Note 2), 0 ≤ TA ≤ 70°C No Load (All Drivers VIN = VCC)(Note 2), – 40°C ≤ TA ≤ 85°C No Load (All Drivers VIN = 0V)(Note 2), – 40°C ≤ TA ≤ 85°C SHUTDOWN (Note 3) q q q q q q q MIN TYP 0.3 0.5 0.3 0.5 35 1.4 1.4 MAX 0.8 1.0 1.0 1.5 50 0.8 UNITS mA mA mA mA µA V V Supply Leakage Current (VCC) On/Off Threshold Low On/Off Threshold High 2.0 AC CHARACTERISTICS VCC = 5V, C1 = C2 = C3 = C4 = 0.1µF, unless otherwise noted. PARAMETER Slew Rate Driver Propagation Delay (TTL to RS232) Receiver Propagation Delay (RS232 to TTL) CONDITIONS RL = 3k, CL = 51pF RL = 3k, CL = 2500pF t HLD (Figure 1) t LHD (Figure 1) t HLR (Figure 2) t LHR (Figure 2) q q q q MIN 3 TYP 8 5 2 2 0.3 0.2 MAX 30 3.5 3.5 0.8 0.8 UNITS V/µs V/µs µs µs µs µs The q denotes specifications which apply over the operating temperature range (0°C ≤ TA ≤ 70°Cfor commercial grade, – 40°C ≤ TA ≤ 85°C for industrial grade). Note 1: Absolute Maximum Ratings are those values beyond which the life of the device may be impaired. Note 2: Supply current is measured with driver and receiver outputs unloaded. Note 3: Supply current and leakage current measurements in SHUTDOWN are performed with VON/OFF = 0V. TYPICAL PERFOR A CE CHARACTERISTICS Driver Output Voltage 10 8 RL = 3k OUTPUT HIGH VCC = 5V DRIVER OUTPUT VOLTAGE (V) THRESHOLD VOLTAGE (V) 4 2 0 –2 –4 –6 VCC = 5V –8 –40 –20 20 0 60 40 TEMPERATURE (°C) 80 100 OUTPUT LOW VCC = 4.5V SUPPLY CURRENT (mA) 6 VCC = 4.5V LTC1349 • TPC01 UW Receiver Input Thresholds 2.2 2.0 1.8 VTH 1.6 VTL 1.4 1.2 5 45 40 35 30 25 20 15 10 Supply Current vs Data Rate VCC = 5V RL = 3k CL = 2500pF 3 DRIVERS ACTIVE 1.0 –40 –20 0 40 20 60 0 TEMPERATURE (˚C) 80 100 0 25 75 100 125 50 DATA RATE (k BAUD) 150 175 LTC1349 • TPC02 LTC1349 • TPC03 3 LTC1349 TYPICAL PERFOR A CE CHARACTERISTICS VCC Supply Current 20 16 3 DRIVERS LOADED RL = 3k LEAKAGE CURRENT (µA) SUPPLY CURRENT (mA) 14 12 10 8 6 4 2 0 0 10 35 30 25 20 15 10 5 0 VOUT = 20V VOUT = – 20V SHORT-CIRCUIT CURRENT (mA) 1 DRIVER LOADED RL = 3k 30 20 40 50 TEMPERATURE (°C) LTC1349 • TPC04 Receiver Short-Circuit Current 60 SHORT-CIRCUIT CURRENT (mA) 50 40 ISC– 30 ISC+ 20 LTC1349 • TPC08 LTC1349 • TPC09 10 –40 –20 40 20 0 60 TEMPERATURE (°C) PI FU CTIO S VCC: 5V Input Supply Pin. Supply current is typically 35µA in the SHUTDOWN mode. This pin should be decoupled with a 0.1µF ceramic capacitor. GND: Ground Pin. ON/OFF: TTL/CMOS Compatible SHUTDOWN Pin. A logic low puts the device in SHUTDOWN mode, with receivers 4 and 5 kept alive and the supply current equal to 35µA. All driver outputs and other receiver outputs are in high impedance state. This pin can not float. V +: Positive Supply Output (RS232 Drivers). V + ≅ 2VCC – 1V. This pin requires an external capacitor C = 0.1µF for charge storage. The capacitor may be tied to ground or 5V. With multiple devices, the V + and V – pins may be paralleled into common capacitors. For large numbers of devices, increasing the size of the shared common storage capacitors is recommended to reduce ripple. V –: Negative Supply Output (RS232 Drivers). V – ≅ 2VCC – 1.5V. This pin requires an external capacitor C = 0.1µF for charge storage. C1+, C1–, C2+, C2–: Commutating Capacitor Inputs. These pins require two external capacitors C = 0.1µF: one from C1+ to C1–, and another from C2+ to C2–. To maintain charge pump efficiency, the capacitor’s effective series resistance should be less than 20Ω. 4 UW 60 70 80 100 LTC1349 • TPC07 Driver Leakage in SHUTDOWN 45 40 20 18 16 14 12 10 8 6 4 60 70 Driver Short-Circuit Current ISC– ISC+ 0 10 30 20 40 50 TEMPERATURE (°C) 0 –40 –20 20 0 60 40 TEMPERATURE (°C) 80 100 LTC1349 • TPC05 LTC1349 • TPC06 Driver Output Waveforms DRIVER OUTPUT RL = 3k CL = 2500pF DRIVER OUTPUT RL = 3k INPUT Receiver Output Waveforms RECEIVER OUTPUT CL = 2500pF INPUT U U U LTC1349 PI FU CTIO S DRIVER IN: RS232 Driver Input Pins. Inputs are TTL/ CMOS compatible. Inputs should not be allowed to float. Tie unused inputs to VCC. DRIVER OUT: Driver Outputs at RS232 Voltage Levels. Outputs are in a high impedance state when in SHUTDOWN mode or VCC = 0V. The driver outputs are protected against ESD to ± 10kV for human body model discharges. RX IN: Receiver Inputs. These pins can be forced to ± 25V without damage. The receiver inputs are protected against ESD to ±10kV for human body model discharges. Each receiver provides 0.4V of hysteresis for noise immunity. RX OUT: Receiver Outputs with TTL/CMOS Voltage Levels. Receiver 1, 2 and 3 outputs are in a high impedance state when in SHUTDOWN mode to allow data line sharing. Receivers 4 and 5 are kept alive in SHUTDOWN. SWITCHI G TI E WAVEFOR S DRIVER INPUT DRIVER OUTPUT t LHD VCC 1.4V 1.4V 0V V+ 0V t HLD LTC1349 • F01 Figure 1. Driver Propagation Delay Timing TEST CIRCUITS Driver Timing Test Load DRIVER OUTPUT DRIVER 51pF 3k RX INPUT RX 51pF DRIVER INPUT LTC1349 • TA03 W W U U U U RX INPUT RX OUTPUT t LHR 1.7V VCC 1.3V 0V 2.4V 0.8V t HLR VCC 0V LTC1349 • F02 0V V– Figure 2. Receiver Propagation Delay Timing Receiver Timing Test Load RX OUTPUT LTC1349 • TA04 5 LTC1349 TEST CIRCUITS ESD Test Circuit V+ C1 0.1µF C2 0.1µF DRIVER 1 OUT RX1 IN RS232 LINE PINS PROTECTED TO ±10kV DRIVER 2 OUT RX2 IN RX3 IN RX4 IN DRIVER 3 OUT RX5 IN ON/OFF NC VCC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LTC1349 28 27 26 25 24 23 22 21 20 19 18 17 16 15 C3 0.1µF DRIVER 1 IN RX1 OUT DRIVER 2 IN RX2 OUT RX3 OUT RX4 OUT DRIVER 3 IN RX5 OUT GND NC NC LTC1349 • TC V– C4 0.1µF 6 LTC1349 PACKAGE DESCRIPTIO 0.205 – 0.212* (5.20 – 5.38) 0° – 8° 0.005 – 0.009 (0.13 – 0.22) 0.022 – 0.037 (0.55 – 0.95) 0.0256 (0.65) BSC 0.010 – 0.015 (0.25 – 0.38) *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm). 0.045 (1.14) 0.002 – 0.008 (0.05 – 0.21) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 0.600 – 0.625 (15.240 – 15.875) 0.130 ± 0.005 (3.302 ± 0.127) 0.015 (0.381) MIN 0.045 – 0.065 (1.143 – 1.651) 0.009 – 0.015 (0.229 – 0.381) ( +0.025 0.625 –0.015 +0.635 –0.381 15.87 ) 0.125 (3.175) MIN 0.035 – 0.080 (0.889 – 2.032) 0.100 ± 0.010 (2.540 ± 0.254) 0.005 (0.127) RAD MIN 0.291 – 0.299 (7.391 – 7.595) (NOTE 2) 0.093 – 0.104 0.010 – 0.029 × 45° (2.362 – 2.642) (0.254 – 0.737) 0° – 8° TYP 0.050 (1.270) TYP 0.009 – 0.013 (0.229 – 0.330) NOTE 1 0.016 – 0.050 (0.406 – 1.270) NOTE: 1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS. 2. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm). Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U Dimensions in inches (millimeters) unless otherwise noted. G Package 28-Lead SSOP 0.397 – 0.407* (10.07 – 10.33) 0.068 – 0.078 (1.73 – 1.99) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 0.301 – 0.311 (7.65 – 7.90) 0.045 (1.14) N Package 28-Lead Plastic DIP 0.070 (1.778) TYP 28 27 26 25 24 23 1.455 (36.957) MAX 22 21 20 19 18 17 16 15 0.505 – 0.560 (12.827 – 14.224) 0.018 ± 0.003 (0.457 ± 0.076) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 S Package 28-Lead SOL 0.697 – 0.712 (17.70 – 18.08) (NOTE 2) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 0.037 – 0.045 (0.940 – 1.143) 0.014 – 0.019 (0.356 – 0.482) 0.004 – 0.012 (0.102 – 0.305) NOTE 1 0.394 – 0.419 (10.007 – 10.643) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 7 LTC1349 U.S. Area Sales Offices NORTHEAST REGION Linear Technology Corporation One Oxford Valley 2300 E. Lincoln Hwy.,Suite 306 Langhorne, PA 19047 Phone: (215) 757-8578 FAX: (215) 757-5631 Linear Technology Corporation 266 Lowell St., Suite B-8 Wilmington, MA 01887 Phone: (508) 658-3881 FAX: (508) 658-2701 SOUTHEAST REGION Linear Technology Corporation 17060 Dallas Parkway Suite 208 Dallas, TX 75248 Phone: (214) 733-3071 FAX: (214) 380-5138 CENTRAL REGION Linear Technology Corporation Chesapeake Square 229 Mitchell Court, Suite A-25 Addison, IL 60101 Phone: (708) 620-6910 FAX: (708) 620-6977 SOUTHWEST REGION Linear Technology Corporation 22141 Ventura Blvd. Suite 206 Woodland Hills, CA 91364 Phone: (818) 703-0835 FAX: (818) 703-0517 NORTHWEST REGION Linear Technology Corporation 782 Sycamore Dr. Milpitas, CA 95035 Phone: (408) 428-2050 FAX: (408) 432-6331 International Sales Offices FRANCE Linear Technology S.A.R.L. Immeuble "Le Quartz" 58 Chemin de la Justice 92290 Chatenay Malabry France Phone: 33-1-41079555 FAX: 33-1-46314613 GERMANY Linear Techonolgy GMBH Untere Hauptstr. 9 D-85386 Eching Germany Phone: 49-89-3197410 FAX: 49-89-3194821 JAPAN Linear Technology KK 5F YZ Bldg. 4-4-12 Iidabashi, Chiyoda-Ku Tokyo, 102 Japan Phone: 81-3-3237-7891 FAX: 81-3-3237-8010 KOREA Linear Technology Korea Branch Namsong Building, #505 Itaewon-Dong 260-199 Yongsan-Ku, Seoul Korea Phone: 82-2-792-1617 FAX: 82-2-792-1619 SINGAPORE Linear Technology Pte. Ltd. 101 Boon Keng Road #02-15 Kallang Ind. Estates Singapore 1233 Phone: 65-293-5322 FAX: 65-292-0398 TAIWAN Linear Technology Corporation Rm. 801, No. 46, Sec. 2 Chung Shan N. Rd. Taipei, Taiwan, R.O.C. Phone: 886-2-521-7575 FAX: 886-2-562-2285 UNITED KINGDOM Linear Technology (UK) Ltd. The Coliseum, Riverside Way Camberley, Surrey GU15 3YL United Kingdom Phone: 44-276-677676 FAX: 44-276-64851 World Headquarters Linear Technology Corporation 1630 McCarthy Blvd. Milpitas, CA 95035-7487 Phone: (408) 432-1900 FAX: (408) 434-0507 08/16/93 8 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7487 (408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977 LT/GP 1093 10K REV 0 • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 1993