LTC2223CUK

LTC2222/LTC2223 12-Bit,105Msps/ 80Msps ADCs FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTIO ■ Sample Rate: 105Msps/80Msps 68dB SNR up to 140MHz Input 80dB SFDR up to 170MHz Input 775MHz Full Power Bandwidth S/H Single 3.3V Supply Low Power Dissipation: 475mW/366mW Selectable Input Ranges: ±0.5V or ±1V No Missing Codes Optional Clock Duty Cycle Stabilizer Shutdown and Nap Modes Data Ready Output Clock Pin Compatible Family 135Msps: LTC2224 (12-Bit), LTC2234 (10-Bit) 105Msps: LTC2222 (12-Bit), LTC2232 (10-Bit) 80Msps: LTC2223 (12-Bit), LTC2233 (10-Bit) 48-Pin QFN Package The LTC®2222 and LTC2223 are 105Msps/80Msps, sampling 12-bit A/D converters designed for digitizing high frequency, wide dynamic range signals. The LTC2222/ LTC2223 are perfect for demanding communications applications with AC performance that includes 68dB SNR and 80dB spurious free dynamic range for signals up to 170MHz. Ultralow jitter of 0.15psRMS allows undersampling of IF frequencies with excellent noise performance. DC specs include ± 0.3LSB INL (typ), ± 0.2LSB DNL (typ) and no missing codes over temperature. The transition noise is a low 0.5LSBRMS. A separate output power supply allows the outputs to drive 0.5V to 3.6V logic. The ENC+ and ENC – inputs may be driven differentially or single ended with a sine wave, PECL, LVDS, TTL, or CMOS inputs. An optional clock duty cycle stabilizer allows high performance at full speed for a wide range of clock duty cycles. , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. APPLICATIO S ■ ■ ■ ■ Wireless and Wired Broadband Communication Cable Head-End Systems Power Amplifier Linearization Communications Test Equipment TYPICAL APPLICATIO REFH REFL VDD 3.3V 100 FLEXIBLE REFERENCE 0VDD 0.5V TO 3.6V + ANALOG INPUT INPUT S/H – 12-BIT PIPELINED ADC CORE CORRECTION LOGIC OUTPUT DRIVERS D11 • • • D0 0GND SFDR (dBFS) CLOCK/DUTY CYCLE CONTROL 22201 TA01 ENCODE INPUT 22223fa U SFDR vs Input Frequency 95 90 85 80 2nd or 3rd 75 70 65 60 0 100 200 300 400 500 600 INPUT FREQUENCY (MHz) 22223 TA01b 4th OR HIGHER U U 1 LTC2222/LTC2223 ABSOLUTE AXI U RATI GS PACKAGE/ORDER I FOR ATIO TOP VIEW OVDD = VDD (Notes 1, 2) UK PACKAGE 48-LEAD (7mm × 7mm) PLASTIC QFN EXPOSED PAD IS GND (PIN 49), MUST BE SOLDERED TO PCB ORDER PART NUMBER LTC2222CUK LTC2223CUK LTC2222IUK LTC2223IUK Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for parts specified with wider operating temperature ranges. CO VERTER CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4) PARAMETER Resolution (No Missing Codes) Integral Linearity Error (Note 5) Differential Linearity Error Integral Linearity Error (Note 5) Differential Linearity Error Offset Error (Note 6) Gain Error Offset Drift Full-Scale Drift Transition Noise Internal Reference External Reference SENSE = 1V External Reference Differential Analog Input Differential Analog Input Single-Ended Analog Input Single-Ended Analog Input ● ● CONDITIONS ● ● ● MIN 12 –1.3 –1 LTC2222 TYP ±0.3 ±0.2 ±1 ±0.2 GND 13 VDD 14 GND 15 ENC + 16 ENC – 17 SHDN 18 OE 19 CLOCKOUT 20 DO 21 OGND 22 OVDD 23 D1 24 Supply Voltage (VDD) ................................................. 4V Digital Output Ground Voltage (OGND) ....... –0.3V to 1V Analog Input Voltage (Note 3) ..... –0.3V to (VDD + 0.3V) Digital Input Voltage .................... –0.3V to (VDD + 0.3V) Digital Output Voltage ............... –0.3V to (OVDD + 0.3V) Power Dissipation ............................................ 1500mW Operating Temperature Range LTC2222C, LTC2223C ............................. 0°C to 70°C LTC2222I, LTC2223I ...........................–40°C to 85°C Storage Temperature Range ..................–65°C to 125°C AIN+ 1 AIN– 2 REFHA 3 REFHA 4 REFLB 5 REFLB 6 REFHB 7 REFHB 8 REFLA 9 REFLA 10 VDD 11 VDD 12 48 GND 47 VDD 46 VDD 45 GND 44 VCM 43 SENSE 42 MODE 41 OF 40 D11 39 D10 38 OGND 37 OVDD 49 36 D9 35 D8 34 D7 33 OVDD 32 OGND 31 D6 30 D5 29 D4 28 OVDD 27 OGND 26 D3 25 D2 TJMAX = 125°C, θJA = 29°C/W UK PART MARKING* LTC2222UK LTC2223UK LTC2222UK LTC2223UK MAX 1.3 1 MIN 12 –1.1 –0.8 LTC2223 TYP ±0.3 ±0.2 ±1 ±0.2 MAX 1.1 0.8 UNITS Bits LSB LSB LSB LSB –30 –2.5 ±3 ±0.5 ±10 ±30 ±15 0.5 30 2.5 –30 –2.5 ±3 ±0.5 ± 10 ± 30 ± 15 0.5 30 2.5 µV/C ppm/C ppm/C LSBRMS 22223fa 2 U mV %FS W U U WW W U LTC2222/LTC2223 A ALOG I PUT SYMBOL VIN VIN, CM IIN ISENSE IMODE tAP tJITTER CMRR The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4) PARAMETER Analog Input Range (AIN+ – AIN–) Analog Input Common Mode (AIN+ Analog Input Leakage Current SENSE Input Leakage MODE Pin Pull-Down Current to GND Full Power Bandwidth Sample and Hold Acquisition Delay Time Sample and Hold Acquisition Delay Time Jitter Analog Input Common Mode Rejection Ratio Figure 8 Test Circuit + AIN–)/2 CONDITIONS 3.1V < VDD < 3.5V Differential Input Single Ended Input (Note 7) 0 < AIN+, AIN– < VDD 0V < SENSE < 1V ● ● ● ● ● DY A IC ACCURACY SYMBOL SNR PARAMETER Signal-to-Noise Ratio The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. AIN = –1dBFS. (Note 4) CONDITIONS 30MHz Input (1V Range) 30MHz Input (2V Range) 70MHz Input (1V Range) 70MHz Input (2V Range) 140MHz Input (1V Range) 140MHz Input (2V Range) 250MHz Input (1V Range) 250MHz Input (2V Range) SFDR Spurious Free Dynamic Range 30MHz Input (1V Range) 30MHz Input (2V Range) 70MHz Input (1V Range) 70MHz Input (2V Range) 140MHz Input (1V Range) 140MHz Input (2V Range) 250MHz Input (1V Range) 250MHz Input (2V Range) SFDR Spurious Free Dynamic Range 4th Harmonic or Higher 30MHz Input (1V Range) 30MHz Input (2V Range) 70MHz Input (1V Range) 70MHz Input (2V Range) 140MHz Input (1V Range) 140MHz Input (2V Range) 250MHz Input (1V Range) 250MHz Input (2V Range) S/(N+D) Signal-to-Noise Plus Distortion Ratio 30MHz Input (1V Range) 30MHz Input (2V Range) 70MHz Input (1V Range) 70MHz Input (2V Range) IMD Intermodulation Distortion fIN1 = 138MHz, fIN2 = 140MHz ● ● ● U WU U MIN 1 0.5 –1 –1 TYP ±0.5 to ±1 1.6 1.6 MAX 1.9 2.1 1 1 UNITS V V V µA µA µA MHz ns psRMS dB 10 775 0 0.15 80 MIN 67 LTC2222 TYP MAX 63.5 68.4 63.4 68.3 63.2 67.9 62.7 67.0 MIN 67.5 LTC2223 TYP MAX 63.6 68.5 63.5 68.4 63.5 68.0 63.0 67.3 UNITS dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dBc 72 84 84 84 84 81 81 77 77 90 90 90 90 90 90 90 90 73 84 84 84 84 84 81 80 75 90 90 90 90 90 90 90 90 66.5 63.5 68.4 63.5 68.2 81 67 63.6 68.5 63.6 68.3 81 22223fa 3 LTC2222/LTC2223 I TER AL REFERE CE CHARACTERISTICS PARAMETER VCM Output Voltage VCM Output Tempco VCM Line Regulation VCM Output Resistance 3.1V < VDD < 3.5V –1mA < IOUT < 1mA CONDITIONS IOUT = 0 DIGITAL I PUTS A D DIGITAL OUTPUTS SYMBOL VID VICM RIN CIN VIH VIL IIN CIN LOGIC OUTPUTS OVDD = 3.3V COZ ISOURCE ISINK VOH VOL OVDD = 2.5V VOH VOL OVDD = 1.8V VOH VOL High Level Output Voltage Low Level Output Voltage IO = –200µA IO = 1.6mA High Level Output Voltage Low Level Output Voltage IO = –200µA IO = 1.6mA Hi-Z Output Capacitance Output Source Current Output Sink Current High Level Output Voltage Low Level Output Voltage OE = High (Note 7) VOUT = 0V VOUT = 3.3V IO = –10µA IO = –200µA IO = 10µA IO = 1.6mA PARAMETER Differential Input Voltage Common Mode Input Voltage Input Resistance Input Capacitance High Level Input Voltage Low Level Input Voltage Input Current Input Capacitance (Note 7) VDD = 3.3V VDD = 3.3V VIN = 0V to VDD (Note 7) CONDITIONS ENCODE INPUTS (ENC +, ENC –) The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4) MIN ● LOGIC INPUTS (OE, SHDN) ● ● ● 4 U U U U U (Note 4) MIN 1.575 TYP 1.600 ±25 3 4 MAX 1.625 UNITS V ppm/°C mV/V Ω TYP MAX UNITS V 0.2 1.1 1.6 1.6 6 3 2 0.8 –10 3 10 2.5 Internally Set Externally Set (Note 7) ● V V kΩ pF V V µA pF 3 50 50 ● ● pF mA mA V V 0.4 V V V V V V 3.1 3.295 3.29 0.005 0.09 2.49 0.09 1.79 0.09 22223fa LTC2222/LTC2223 The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 8) SYMBOL VDD OVDD IVDD PDISS PSHDN PNAP PARAMETER Analog Supply Voltage Output Supply Voltage Analog Supply Current Power Dissipation Shutdown Power Nap Mode Power SHDN = H, OE = H, No CLK SHDN = H, OE = L, No CLK CONDITIONS (Note 7) (Note 7) ● ● ● ● POWER REQUIRE E TS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4) SYMBOL fS tL tH tAP tD tC tOE Pipeline Latency Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to ground with GND and OGND wired together (unless otherwise noted). Note 3: When these pin voltages are taken below GND or above VDD, they will be clamped by internal diodes. This product can handle input currents of greater than 100mA below GND or above VDD without latchup. Note 4: VDD = 3.3V, fSAMPLE = 105MHz (LTC2222) or 80MHz (LTC2223), differential ENC+/ENC– = 2VP-P sine wave, input range = 2VP-P with differential drive, unless otherwise noted. PARAMETER Sampling Frequency ENC Low Time ENC High Time Sample-and-Hold Aperture Delay ENC to DATA Delay ENC to CLOCKOUT Delay DATA to CLOCKOUT Skew Output Enable Delay (Note 7) (Note 7) (tC - tD) (Note 7) (Note 7) ● ● ● ● TI I G CHARACTERISTICS UW MIN 3.1 0.5 LTC2222 TYP MAX 3.3 3.3 144 475 2 35 3.5 3.6 162 535 MIN 3.1 0.5 LTC2223 TYP MAX 3.3 3.3 111 366 2 35 3.5 3.6 123 406 UNITS V V mA mW mW mW UW CONDITIONS ● MIN 1 4.5 3 4.5 3 1.3 1.3 –0.6 ● ● ● ● LTC2222 TYP MAX 105 4.76 4.76 4.76 4.76 0 2.1 2.1 0 5 5 4 4 0.6 10 500 500 500 500 MIN 1 5.9 3 5.9 3 1.3 1.3 –0.6 LTC2223 TYP MAX 80 6.25 6.25 6.25 6.25 0 2.1 2.1 0 5 5 4 4 0.6 10 500 500 500 500 UNITS MHz ns ns ns ns ns ns ns ns ns Cycles Duty Cycle Stabilizer Off Duty Cycle Stabilizer On Duty Cycle Stabilizer Off Duty Cycle Stabilizer On Note 5: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 6: Offset error is the offset voltage measured from –0.5 LSB when the output code flickers between 0000 0000 0000 and 1111 1111 1111 in 2’s complement output mode. Note 7: Guaranteed by design, not subject to test. Note 8: VDD = 3.3V, fSAMPLE = 105MHz (LTC2222) or 80MHz (LTC2223), differential ENC+/ENC– = 2VP-P sine wave, input range = 1VP-P with differential drive. 22223fa 5 LTC2222/LTC2223 TYPICAL PERFOR A CE CHARACTERISTICS LTC2222: INL, 2V Range 1.0 0.8 0.6 0.4 ERROR (LSB) ERROR (LSB) 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 0 1024 3072 2048 OUTPUT CODE 4096 2222 G01 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 0 1024 3072 2048 OUTPUT CODE 4096 2222 G02 SNR (dBFS) LTC2222: SNR vs Input Frequency, –1dB, 1V Range 70 69 68 67 SFDR (dBFS) SNR (dBFS) 66 65 64 63 62 61 60 0 100 200 300 400 500 600 2222 G04 INPUT FREQUENCY (MHz) 80 75 70 65 60 55 0 100 200 300 400 500 600 2222 G05 INPUT FREQUENCY (MHz) SFDR (dBFS) LTC2222: SFDR (HD4+) vs Input Frequency, –1dB, 2V Range 100 95 90 SFDR (dBFS) SFDR (dBFS) 85 80 75 70 65 60 55 0 100 200 300 400 500 600 INPUT FREQUENCY (MHz) 2222 G07 85 80 75 70 65 60 55 0 100 200 300 400 500 600 INPUT FREQUENCY (MHz) 2222 G08 SFDR AND SNR (dBFS) 6 UW LTC2222: DNL, 2V Range 1.0 0.8 0.6 0.4 70 69 68 67 66 65 64 63 62 61 60 LTC2222: SNR vs Input Frequency, –1dB, 2V Range 0 100 300 400 500 600 200 2222 G03 INPUT FREQUENCY (MHz) LTC2222: SFDR (HD2 and HD3) vs Input Frequency, –1dB, 2V Range 100 95 90 85 100 95 90 85 80 75 70 65 60 55 LTC2222: SFDR (HD2 and HD3) vs Input Frequency, –1dB, 1V Range 0 100 200 300 400 500 600 2222 G06 INPUT FREQUENCY (MHz) LTC2222: SFDR (HD4+) vs Input Frequency, –1dB, 1V Range 100 95 90 100 95 90 85 80 75 70 65 60 LTC2222: SFDR and SNR vs Sample Rate, 2V Range, fIN = 30MHz, –1dB SFDR SNR 0 20 40 60 80 100 120 2222 G09 SAMPLE RATE (Msps) 22223fa LTC2222/LTC2223 TYPICAL PERFOR A CE CHARACTERISTICS LTC2222: SFDR and SNR vs Sample Rate, 1V Range, fIN = 30MHz, –1dB 100 95 90 SFDR 120 130 SFDR AND SNR (dBFS) 85 IVDD (mA) 80 75 70 65 60 55 50 SNR 110 2V RANGE 1V RANGE IOVDD (mA) 0 20 40 60 80 SAMPLE RATE (Msps) LTC2222: SFDR vs Input Level, f IN = 70MHz, 2V Range 100 90 80 dBFS SFDR (dBc AND dBFS) AMPLITUDE (dB) 60 50 40 30 20 10 0 –60 dBc – 50 – 60 – 70 – 80 – 90 AMPLITUDE (dB) 70 –50 –40 –30 –20 INPUT LEVELS (dBFS) LTC2222: 8192 Point FFT, f IN = 30MHz, –1dB, 2V Range 0 – 10 – 20 – 30 0 – 10 – 20 – 30 AMPLITUDE (dB) AMPLITUDE (dB) – 50 – 60 – 70 – 80 – 90 – 50 – 60 – 70 – 80 – 90 AMPLITUDE (dB) – 40 – 100 – 110 – 120 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 UW 100 2223 G10 LTC2222: IVDD vs Sample Rate, 5MHz Sine Wave Input, –1dB 8 LTC2222: IOVDD vs Sample Rate, 5MHz Sine Wave Input, –1dB,OVDD = 1.8V 6 4 100 90 2 80 0 20 60 80 40 SAMPLE RATE (Msps) 100 2223 G11 0 0 20 60 80 40 SAMPLE RATE (Msps) 100 2223 G12 LTC2222: 8192 Point FFT, f IN = 5MHz, –1dB, 2V Range 0 – 10 – 20 – 30 – 40 0 – 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 – 100 – 110 – 120 LTC2222: 8192 Point FFT, f IN = 5MHz, –1dB, 1V Range – 100 – 110 – 120 –10 0 2223 G13 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 2223 G14 2223 G15 LTC2222: 8192 Point FFT, f IN = 30MHz, –1dB, 1V Range 0 – 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 – 100 – 110 – 120 LTC2222: 8192 Point FFT, f IN = 70MHz, –1dB, 2V Range – 40 – 100 – 110 – 120 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 2223 G16 2223 G17 2223 G18 22223fa 7 LTC2222/LTC2223 TYPICAL PERFOR A CE CHARACTERISTICS LTC2222: 8192 Point FFT, f IN = 70MHz, –1dB, 1V Range 0 –10 –20 –30 AMPLITUDE (dB) AMPLITUDE (dB) AMPLITUDE (dB) –40 –50 –60 –70 –80 –90 –100 –110 –120 0 5 10 15 20 25 30 FREQUENCY (MHz) LTC2222: 8192 Point FFT, f IN = 250MHz, –1dB, 2V Range 0 –10 –20 –30 AMPLITUDE (dB) AMPLITUDE (dB) AMPLITUDE (dB) –40 –50 –60 –70 –80 –90 –100 –110 –120 0 5 10 15 20 25 30 FREQUENCY (MHz) LTC2222: 8192 Point 2-Tone FFT, f IN = 68MHz and 70MHz, –7dB Each, 2V Range 0 –10 –20 –30 AMPLITUDE (dB) AMPLITUDE (dB) –40 –50 –60 –70 –80 –90 –60 –70 –80 –90 COUNT –100 –110 –120 0 5 10 15 20 25 30 FREQUENCY (MHz) 8 UW 35 2223 G19 LTC2222: 8192 Point FFT, f IN = 140MHz, –1dB, 2V Range 0 –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 40 –120 0 5 10 15 20 25 30 FREQUENCY (MHz) LTC2222: 8192 Point FFT, f IN = 140MHz, –1dB, 1V Range 0 –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 35 40 0 5 10 2223 G20 15 20 25 30 FREQUENCY (MHz) 35 40 2223 G21 LTC2222: 8192 Point FFT, f IN = 250MHz, –1dB, 1V Range 0 –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 LTC2222: 8192 Point FFT, f IN = 500MHz, –6dB, 1V Range 0 –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 –110 –120 35 40 0 5 10 2223 G22 15 20 25 30 FREQUENCY (MHz) 35 40 0 5 10 2223 G23 15 20 25 30 FREQUENCY (MHz) 35 40 2223 G24 LTC2222: 8192 Point 2-Tone FFT, f IN = 138MHz and 140MHz, –7dB Each, 1V Range 0 –10 –20 –30 –40 –50 60000 80000 100000 LTC2222: Shorted Input Noise Histogram 96679 40000 –100 –110 35 40 –120 0 5 10 15 20 25 30 FREQUENCY (MHz) 20000 16182 18080 35 40 0 42 2044 2045 2046 CODE 2047 89 2048 2223 G27 2223 G25 2223 G26 22223fa LTC2222/LTC2223 TYPICAL PERFOR A CE CHARACTERISTICS LTC2223: INL, 2V Range 1.0 0.8 0.6 0.4 ERROR (LSB) ERROR (LSB) 0.2 0 – 0.2 – 0.4 – 0.6 – 0.8 – 1.0 0 1024 3072 2048 OUTPUT CODE 4096 2223 G01 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 0 1024 3072 2048 OUTPUT CODE 4096 2223 G02 SNR (dBFS) LTC2223: SNR vs Input Frequency, –1dB, 1V Range 70 69 68 67 SFDR (dBFS) SNR (dBFS) 66 65 64 63 70 62 61 60 0 100 200 300 400 500 600 2223 G04 INPUT FREQUENCY (MHz) 65 60 90 100 95 80 75 SFDR (dBFS) LTC2223: SFDR (HD4+) vs Input Frequency, –1dB, 2V Range 100 95 90 SFDR (dBFS) SFDR (dBFS) 85 80 75 70 65 60 0 100 200 300 400 500 600 INPUT FREQUENCY (MHz) 2223 G07 100 95 SFDR AND SNR (dBFS) UW LTC2223: DNL, 2V Range 1.0 0.8 0.6 0.4 70 69 68 67 66 65 64 63 62 61 60 LTC2223: SNR vs Input Frequency, –1dB, 2V Range 0 100 300 400 500 600 200 2223 G03 INPUT FREQUENCY (MHz) LTC2223: SFDR (HD2 and HD3) vs Input Frequency, –1dB, 2V Range 100 95 90 85 80 75 70 65 0 100 200 300 400 500 600 2223 G05 INPUT FREQUENCY (MHz) 60 LTC2223: SFDR (HD2 and HD3) vs Input Frequency, –1dB, 1V Range 85 0 100 200 300 400 500 600 2223 G06 INPUT FREQUENCY (MHz) LTC2223: SFDR (HD4+) vs Input Frequency, –1dB, 1V Range 100 95 90 90 85 80 75 70 65 60 0 100 200 300 400 500 600 INPUT FREQUENCY (MHz) 2223 G08 85 80 75 70 65 60 55 50 LTC2223: SFDR and SNR vs Sample Rate, 2V Range, fIN = 30MHz, –1dB SFDR SNR 0 20 40 60 80 100 2223 G09 SAMPLE RATE (Msps) 22223fa 9 LTC2222/LTC2223 TYPICAL PERFOR A CE CHARACTERISTICS LTC2223: SFDR and SNR vs Sample Rate, 1V Range, fIN = 30MHz, –1dB 100 95 90 SFDR 120 130 SFDR AND SNR (dBFS) 85 IVDD (mA) 80 75 70 65 60 55 50 SNR 110 2V RANGE 100 1V RANGE IOVDD (mA) 100 2223 G11 0 20 40 60 80 SAMPLE RATE (Msps) LTC2223: SFDR vs Input Level, f IN = 70MHz, 2V Range 100 90 80 dBFS 0 – 10 – 20 – 30 SFDR (dBc AND dBFS) AMPLITUDE (dB) 60 50 40 30 20 10 0 –60 –50 dBc – 50 – 60 – 70 – 80 – 90 AMPLITUDE (dB) 70 –40 –30 –20 INPUT LEVELS (dBFS) LTC2223: 8192 Point FFT, f IN = 30MHz, –1dB, 2V Range 0 – 10 – 20 – 30 0 – 10 – 20 – 30 AMPLITUDE (dB) AMPLITUDE (dB) – 50 – 60 – 70 – 80 – 90 – 50 – 60 – 70 – 80 – 90 AMPLITUDE (dB) – 40 – 100 – 110 – 120 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 10 UW 100 2223 G10 LTC2223: IVDD vs Sample Rate, 5MHz Sine Wave Input, –1dB 8 LTC2223: IOVDD vs Sample Rate, 5MHz Sine Wave Input, –1dB,OVDD = 1.8V 6 4 90 2 80 0 20 60 80 40 SAMPLE RATE (Msps) 0 0 20 60 80 40 SAMPLE RATE (Msps) 100 2223 G12 LTC2223: 8192 Point FFT, f IN = 5MHz, –1dB, 2V Range 0 – 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 – 100 – 110 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 – 120 LTC2223: 8192 Point FFT, f IN = 5MHz, –1dB, 1V Range – 40 – 100 – 110 – 120 –10 0 2223 G13 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 2223 G14 2223 G15 LTC2223: 8192 Point FFT, f IN = 30MHz, –1dB, 1V Range 0 – 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 – 100 – 110 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 – 120 LTC2223: 8192 Point FFT, f IN = 70MHz, –1dB, 2V Range – 40 – 100 – 110 – 120 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 2223 G16 2223 G17 2223 G18 22223fa LTC2222/LTC2223 TYPICAL PERFOR A CE CHARACTERISTICS LTC2223: 8192 Point FFT, f IN = 70MHz, –1dB, 1V Range 0 – 10 – 20 – 30 0 – 10 – 20 – 30 AMPLITUDE (dB) AMPLITUDE (dB) – 50 – 60 – 70 – 80 – 90 – 50 – 60 – 70 – 80 – 90 AMPLITUDE (dB) – 40 – 100 – 110 – 120 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 LTC2223: 8192 Point FFT, f IN = 250MHz, –1dB, 2V Range 0 – 10 – 20 – 30 0 – 10 – 20 – 30 AMPLITUDE (dB) AMPLITUDE (dB) – 50 – 60 – 70 – 80 – 90 – 50 – 60 – 70 – 80 – 90 AMPLITUDE (dB) – 40 – 100 – 110 – 120 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 LTC2223: 8192 Point 2-Tone FFT, f IN = 68MHz and 70MHz, –7dB Each, 2V Range 0 – 10 – 20 – 30 0 – 10 – 20 – 30 AMPLITUDE (dB) AMPLITUDE (dB) – 40 – 50 – 60 – 70 – 80 – 90 – 60 – 70 – 80 – 90 COUNT – 100 – 110 – 120 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 UW 2223 G19 2223 G22 2223 G25 LTC2223: 8192 Point FFT, f IN = 140MHz, –1dB, 2V Range 0 – 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 – 100 – 110 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 – 120 LTC2223: 8192 Point FFT, f IN = 140MHz, –1dB, 1V Range – 40 – 100 – 110 – 120 0 5 10 2223 G20 15 20 25 30 FREQUENCY (MHz) 35 40 2223 G21 LTC2223: 8192 Point FFT, f IN = 250MHz, –1dB, 1V Range 0 – 10 – 20 – 30 – 40 – 50 – 60 – 70 – 80 – 90 – 100 – 110 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 – 120 LTC2223: 8192 Point FFT, f IN = 500MHz, –6dB, 1V Range – 40 – 100 – 110 – 120 0 5 10 2223 G23 15 20 25 30 FREQUENCY (MHz) 35 40 2223 G24 LTC2223: 8192 Point 2-Tone FFT, f IN = 138MHz and 140MHz, –7dB Each, 1V Range 100000 LTC2223: Shorted Input Noise Histogram 96679 80000 – 40 – 50 60000 40000 16182 18080 – 100 – 110 – 120 0 5 10 15 20 25 30 FREQUENCY (MHz) 35 40 20000 42 2044 0 89 2045 2046 CODE 2047 2048 2223 G27 2223 G26 22223fa 11 LTC2222/LTC2223 PI FU CTIO S AIN+ (Pin 1): Positive Differential Analog Input. AIN– (Pin 2): Negative Differential Analog Input. REFHA (Pins 3, 4): ADC High Reference. Bypass to Pins 5, 6 with 0.1µF ceramic chip capacitor, to Pins 9, 10 with a 2.2µF ceramic capacitor and to ground with a 1µF ceramic capacitor. REFLB (Pins 5, 6): ADC Low Reference. Bypass to Pins 3, 4 with 0.1µF ceramic chip capacitor. Do not connect to Pins 9, 10. REFHB (Pins 7, 8): ADC High Reference. Bypass to Pins 9, 10 with 0.1µF ceramic chip capacitor. Do not connect to Pins 3, 4. REFLA (Pins 9, 10): ADC Low Reference. Bypass to Pins 7, 8 with 0.1µF ceramic chip capacitor, to Pins 3, 4 with a 2.2µF ceramic capacitor and to ground with a 1µF ceramic capacitor. VDD (Pins 11, 12, 14, 46, 47): 3.3V Supply. Bypass to GND with 0.1µF ceramic chip capacitors. Adjacent pins can share a bypass capacitor. GND (Pins 13, 15, 45, 48): ADC Power Ground. ENC + (Pin 16): Encode Input. The input is sampled on the positive edge. ENC – (Pin 17): Encode Complement Input. The input is sampled on the negative edge. Bypass to ground with 0.1µF ceramic for single-ended ENCODE signal. SHDN (Pin 18): Shutdown Mode Selection Pin. Connecting SHDN to GND and OE to GND results in normal operation with the outputs enabled. Connecting SHDN to GND and OE to VDD results in normal operation with the outputs at high impedance. Connecting SHDN to VDD and OE to GND results in nap mode with the outputs at high impedance. Connecting SHDN to VDD and OE to VDD results in sleep mode with the outputs at high impedance. OE (Pin 19): Output Enable Pin. Refer to SHDN pin function. CLOCKOUT (Pin 20): Data Valid Output. Latch data on the falling edge of CLKOUT. D0 – D11 (Pins 21, 24, 25, 26, 29, 30, 31, 34, 35, 36, 39, 40): Digital Outputs. D11 is the MSB. OGND (Pins 22, 27, 32, 38): Output Driver Ground. OVDD (Pins 23, 28, 33, 37): Positive Supply for the Output Drivers. Bypass to ground with 0.1µF ceramic chip capacitors. OF (Pin 41): Over/Under Flow Output. High when an over or under flow has occurred. MODE (Pin 42): Output Format and Clock Duty Cycle Stabilizer Selection Pin. Connecting MODE to 0V selects offset binary output format and turns the clock duty cycle stabilizer off. Connecting MODE to 1/3 VDD selects offset binary output format and turns the clock duty cycle stabilizer on. Connecting MODE to 2/3 VDD selects 2’s complement output format and turns the clock duty cycle stabilizer on. Connecting MODE to VDD selects 2’s complement output format and turns the clock duty cycle stabilizer off. SENSE (Pin 43): Reference Programming Pin. Connecting SENSE to VCM selects the internal reference and a ±0.5V input range. VDD selects the internal reference and a ±1V input range. An external reference greater than 0.5V and less than 1V applied to SENSE selects an input range of ±VSENSE. ±1V is the largest valid input range. VCM (Pin 44): 1.6V Output and Input Common Mode Bias. Bypass to ground with 2.2µF ceramic chip capacitor. GND (Exposed Pad): ADC Power Ground. The exposed pad on the bottom of the package needs to be soldered to ground. 12 U U U 22223fa LTC2222/LTC2223 FUNCTIONAL BLOCK DIAGRA AIN+ INPUT S/H FIRST PIPELINED ADC STAGE SECOND PIPELINED ADC STAGE THIRD PIPELINED ADC STAGE FOURTH PIPELINED ADC STAGE FIFTH PIPELINED ADC STAGE AIN– VCM 2.2µF 1.6V REFERENCE SHIFT REGISTER AND CORRECTION RANGE SELECT REFH SENSE REF BUF DIFF REF AMP REFLB REFHA 2.2µF 0.1µF 1µF Figure 1. Functional Block Diagram TI I G DIAGRA S Timing Diagram tAP ANALOG INPUT N tH tL ENC – ENC + tD D0-D11, OF tC N–5 N–4 N–3 N–2 N–1 N+1 N+2 N+3 N+4 CLOCKOUT OE t OE DATA OF, D0-D11, CLKOUT t OE W REFL INTERNAL CLOCK SIGNALS OVDD OF DIFFERENTIAL INPUT LOW JITTER CLOCK DRIVER CONTROL LOGIC OUTPUT DRIVERS • • • D11 D0 CLKOUT REFLA REFHB ENC+ 0.1µF 1µF ENC– M0DE SHDN OE 22223 F01 W U UW U OGND 22223 TD02 22223fa 13 LTC2222/LTC2223 APPLICATIO S I FOR ATIO DYNAMIC PERFORMANCE Signal-to-Noise Plus Distortion Ratio The signal-to-noise plus distortion ratio [S/(N + D)] is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components at the ADC output. The output is band limited to frequencies above DC to below half the sampling frequency. Signal-to-Noise Ratio The signal-to-noise ratio (SNR) is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components except the first five harmonics and DC. Total Harmonic Distortion Total harmonic distortion is the ratio of the RMS sum of all harmonics of the input signal to the fundamental itself. The out-of-band harmonics alias into the frequency band between DC and half the sampling frequency. THD is expressed as: THD = 20Log (√(V22 + V32 + V42 + . . . Vn2)/V1) where V1 is the RMS amplitude of the fundamental frequency and V2 through Vn are the amplitudes of the second through nth harmonics. The THD calculated in this data sheet uses all the harmonics up to the fifth. Intermodulation Distortion If the ADC input signal consists of more than one spectral component, the ADC transfer function nonlinearity can produce intermodulation distortion (IMD) in addition to THD. IMD is the change in one sinusoidal input caused by the presence of another sinusoidal input at a different frequency. 14 U If two pure sine waves of frequencies fa and fb are applied to the ADC input, nonlinearities in the ADC transfer function can create distortion products at the sum and difference frequencies of mfa ± nfb, where m and n = 0, 1, 2, 3, etc. The 3rd order intermodulation products are 2fa + fb, 2fb + fa, 2fa – fb and 2fb – fa. The intermodulation distortion is defined as the ratio of the RMS value of either input tone to the RMS value of the largest 3rd order intermodulation product. Spurious Free Dynamic Range (SFDR) Spurious free dynamic range is the peak harmonic or spurious noise that is the largest spectral component excluding the input signal and DC. This value is expressed in decibels relative to the RMS value of a full scale input signal. Input Bandwidth The input bandwidth is that input frequency at which the amplitude of the reconstructed fundamental is reduced by 3dB for a full scale input signal. Aperture Delay Time The time from when a rising ENC+ equals the ENC– voltage to the instant that the input signal is held by the sample and hold circuit. Aperture Delay Jitter The variation in the aperture delay time from conversion to conversion. This random variation will result in noise when sampling an AC input. The signal to noise ratio due to the jitter alone will be: SNRJITTER = –20log (2π • fIN • tJITTER) 22223fa W UU LTC2222/LTC2223 APPLICATIO S I FOR ATIO CONVERTER OPERATION As shown in Figure 1, the LTC2222/LTC2223 is a CMOS pipelined multistep converter. The converter has five pipelined ADC stages; a sampled analog input will result in a digitized value five cycles later (see the Timing Diagram section). For optimal AC performance the analog inputs should be driven differentially. For cost sensitive applications, the analog inputs can be driven single-ended with slightly worse harmonic distortion. The encode input is differential for improved common mode noise immunity. The LTC2222/LTC2223 has two phases of operation, determined by the state of the differential ENC+/ENC– input pins. For brevity, the text will refer to ENC+ greater than ENC– as ENC high and ENC+ less than ENC– as ENC low. Each pipelined stage shown in Figure 1 contains an ADC, a reconstruction DAC and an interstage residue amplifier. In operation, the ADC quantizes the input to the stage and the quantized value is subtracted from the input by the DAC to produce a residue. The residue is amplified and output by the residue amplifier. Successive stages operate out of phase so that when the odd stages are outputting their residue, the even stages are acquiring that residue and vice versa. When ENC is low, the analog input is sampled differentially directly onto the input sample-and-hold capacitors, inside the “Input S/H” shown in the block diagram. At the instant that ENC transitions from low to high, the sampled input is held. While ENC is high, the held input voltage is buffered by the S/H amplifier which drives the first pipelined ADC stage. The first stage acquires the output of the S/H during this high phase of ENC. When ENC goes back low, the first stage produces its residue which is acquired by the second stage. At the same time, the input S/H goes back to acquiring the analog input. When ENC goes back high, the second stage produces its residue which is acquired by the third stage. An identical process is repeated for the third and fourth stages, resulting in a fourth stage residue that is sent to the fifth stage ADC for final evaluation. U Each ADC stage following the first has additional range to accommodate flash and amplifier offset errors. Results from all of the ADC stages are digitally synchronized such that the results can be properly combined in the correction logic before being sent to the output buffer. SAMPLE/HOLD OPERATION AND INPUT DRIVE Sample/Hold Operation Figure 2 shows an equivalent circuit for the LTC2222/ LTC2223 CMOS differential sample-and-hold. The analog inputs are connected to the sampling capacitors (CSAMPLE) through NMOS transistors. The capacitors shown attached to each input (CPARASITIC) are the summation of all other capacitance associated with each input. LTC2222/LTC2223 VDD 15Ω CPARASITIC 1pF CSAMPLE 1.6pF CPARASITIC 1pF VDD CSAMPLE 1.6pF AIN+ VDD 15Ω AIN– 1.6V 6k ENC+ ENC– 6k 1.6V 22223 F02 W U U Figure 2. Equivalent Input Circuit 22223fa 15 LTC2222/LTC2223 APPLICATIO S I FOR ATIO During the sample phase when ENC is low, the transistors connect the analog inputs to the sampling capacitors and they charge to, and track the differential input voltage. When ENC transitions from low to high, the sampled input voltage is held on the sampling capacitors. During the hold phase when ENC is high, the sampling capacitors are disconnected from the input and the held voltage is passed to the ADC core for processing. As ENC transitions from high to low, the inputs are reconnected to the sampling capacitors to acquire a new sample. Since the sampling capacitors still hold the previous sample, a charging glitch proportional to the change in voltage between samples will be seen at this time. If the change between the last sample and the new sample is small, the charging glitch seen at the input will be small. If the input change is large, such as the change seen with input frequencies near Nyquist, then a larger charging glitch will be seen. Single-Ended Input For cost sensitive applications, the analog inputs can be driven single-ended. With a single-ended input the harmonic distortion and INL will degrade, but the SNR and DNL will remain unchanged. For a single-ended input, AIN+ should be driven with the input signal and AIN– should be connected to 1.6V or VCM. Common Mode Bias For optimal performance the analog inputs should be driven differentially. Each input should swing ±0.5V for the 2V range or ±0.25V for the 1V range, around a common mode voltage of 1.6V. The VCM output pin (Pin 44) may be used to provide the common mode bias level. VCM can be tied directly to the center tap of a transformer to set the DC input level or as a reference level to an op amp differential driver circuit. The VCM pin must be bypassed to ground close to the ADC with a 2.2µF or greater capacitor. Input Drive Impedance As with all high performance, high speed ADCs, the dynamic performance of the LTC2222/LTC2223 can be influenced by the input drive circuitry, particularly the second and third harmonics. Source impedance and input reactance can influence SFDR. At the falling edge of ENC, 16 U the sample-and-hold circuit will connect the 1.6pF sampling capacitor to the input pin and start the sampling period. The sampling period ends when ENC rises, holding the sampled input on the sampling capacitor. Ideally the input circuitry should be fast enough to fully charge the sampling capacitor during the sampling period 1/(2FENCODE); however, this is not always possible and the incomplete settling may degrade the SFDR. The sampling glitch has been designed to be as linear as possible to minimize the effects of incomplete settling. For the best performance, it is recommended to have a source impedance of 100Ω or less for each input. The source impedance should be matched for the differential inputs. Poor matching will result in higher even order harmonics, especially the second. Input Drive Circuits Figure 3 shows the LTC2222/LTC2223 being driven by an RF transformer with a center tapped secondary. The secondary center tap is DC biased with VCM, setting the ADC input signal at its optimum DC level. Terminating on the transformer secondary is desirable, as this provides a common mode path for charging glitches caused by the sample and hold. Figure 3 shows a 1:1 turns ratio transformer. Other turns ratios can be used if the source impedance seen by the ADC does not exceed 100Ω for each ADC input. A disadvantage of using a transformer is the loss of low frequency response. Most small RF transformers have poor performance at frequencies below 1MHz. VCM 2.2µF 0.1µF ANALOG INPUT T1 1:1 25Ω 25Ω 25Ω 0.1µF 12pF 25Ω AIN– 22223 F03 W UU AIN+ LTC2222/23 T1 = MA/COM ETC1-1T RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE Figure 3. Single-Ended to Differential Conversion Using a Transformer 22223fa LTC2222/LTC2223 APPLICATIO S I FOR ATIO Figure 4 demonstrates the use of a differential amplifier to convert a single ended input signal into a differential input signal. The advantage of this method is that it provides low frequency input response; however, the limited gain bandwidth of most op amps will limit the SFDR at high input frequencies. Figure 5 shows a single-ended input circuit. The impedance seen by the analog inputs should be matched. This circuit is not recommended if low distortion is required. The 25Ω resistors and 12pF capacitor on the analog inputs serve two purposes: isolating the drive circuitry from the sample-and-hold charging glitches and limiting the wideband noise at the converter input. For input frequencies higher than 100MHz, the capacitor may need to be decreased to prevent excessive signal loss. For input frequencies above 100MHz the input circuits of Figure 6, 7 and 8 are recommended. The balun transformer gives better high frequency response than a flux coupled center tapped transformer. The coupling capacitors allow the analog inputs to be DC biased at 1.6V. In Figure 8 the series inductors are impedance matching elements that maximize the ADC bandwidth. Reference Operation Figure 9 shows the LTC2222/LTC2223 reference circuitry consisting of a 1.6V bandgap reference, a difference amplifier and switching and control circuit. The internal voltage reference can be configured for two pin selectable U input ranges of 2V (±1V differential) or 1V (±0.5V differential). Tying the SENSE pin to VDD selects the 2V range; typing the SENSE pin to VCM selects the 1V range. The 1.6V bandgap reference serves two functions: its output provides a DC bias point for setting the common mode voltage of any external input circuitry; additionally, the reference is used with a difference amplifier to generate the differential reference levels needed by the internal ADC circuitry. An external bypass capacitor is required for the 1.6V reference output, VCM. This provides a high frequency low impedance path to ground for internal and external circuitry. The difference amplifier generates the high and low reference for the ADC. High speed switching circuits are connected to these outputs and they must be externally bypassed. Each output has four pins: two each of REFHA and REFHB for the high reference and two each of REFLA and REFLB for the low reference. The multiple output pins are needed to reduce package inductance. Bypass capacitors must be connected as shown in Figure 9. Other voltage ranges in between the pin selectable ranges can be programmed with two external resistors as shown in Figure 10. An external reference can be used by applying its output directly or through a resistor divider to SENSE. It is not recommended to drive the SENSE pin with a logic device. The SENSE pin should be tied to the appropriate level as close to the converter as possible. If the SENSE pin is driven externally, it should be bypassed to ground as close to the device as possible with a 1µF ceramic capacitor. 22223fa W UU 17 LTC2222/LTC2223 APPLICATIO S I FOR ATIO VCM HIGH SPEED DIFFERENTIAL AMPLIFIER 25Ω ANALOG INPUT 2.2µF AIN+ LTC2222/23 + CM + – 3pF 12pF 25Ω 3pF AIN– 22223 F04 – AMPLIFIER = LTC6600-20, LT1993, ETC. Figure 4. Differential Drive with an Amplifier VCM 2.2µF 0.1µF ANALOG INPUT T1 0.1µF 25Ω 12Ω AIN– T1 = MA/COM ETC1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE 22223 F06 12Ω 25Ω 0.1µF AIN+ LTC2222/23 8pF 0.1µF Figure 6. Recommended Front End Circuit for Input Frequencies Between 100MHz and 250MHz 18 U VCM 1k 1k 25Ω 2.2µF AIN+ 0.1µF ANALOG INPUT LTC2222/23 12pF 25Ω 0.1µF AIN– 22223 F05 W UU Figure 5. Single-Ended Drive VCM 2.2µF 0.1µF ANALOG INPUT T1 25Ω AIN– T1 = MA/COM ETC1-1-13 RESISTORS, CAPACITORS ARE 0402 PACKAGE SIZE 22223 F07 AIN+ 25Ω 0.1µF LTC2222/23 Figure 7. Recommended Front End Circuit for Input Frequencies Between 250MHz and 500MHz 22223fa LTC2222/LTC2223 APPLICATIO S I FOR ATIO VCM 2.2µF 0.1µF ANALOG INPUT T1 0.1µF 25Ω 4.7nH AIN– T1 = MA/COM ETC1-1-13 RESISTORS, CAPACITORS, INDUCTORS ARE 0402 PACKAGE SIZE 25Ω 4.7nH 0.1µF 2pF AIN+ LTC2222/23 Figure 8. Recommended Front End Circuit for Input Frequencies Above 500MHz 1.6V VCM 2.2µF SENSE 1µF LTC2222/ LTC2223 12k 0.8V 12k 22223 F10 Figure 10. 1.6V Range ADC U LTC2222/LTC2223 1.6V VCM 2.2µF 4Ω 1.6V BANDGAP REFERENCE 1V RANGE DETECT AND CONTROL SENSE REFLB 0.1µF REFHA BUFFER INTERNAL ADC HIGH REFERENCE 0.5V 22223 F08 W UU TIE TO VDD FOR 2V RANGE; TIE TO VCM FOR 1V RANGE; RANGE = 2 • VSENSE FOR 0.5V < VSENSE < 1V 1µF 2.2µF 1µF DIFF AMP REFLA 0.1µF REFHB INTERNAL ADC LOW REFERENCE 22223 F09 Figure 9. Equivalent Reference Circuit 22223fa 19 LTC2222/LTC2223 APPLICATIO S I FOR ATIO Input Range The input range can be set based on the application. The 2V input range will provide the best signal-to-noise performance while maintaining excellent SFDR. The 1V input range will have better SFDR performance, but the SNR will degrade by 5dB. See the Typical Performance Characteristics section. Driving the Encode Inputs The noise performance of the LTC2222/LTC2223 can depend on the encode signal quality as much as on the analog input. The ENC+/ENC– inputs are intended to be driven differentially, primarily for noise immunity from common mode noise sources. Each input is biased through a 6k resistor to a 1.6V bias. The bias resistors set the DC operating point for transformer coupled drive circuits and can set the logic threshold for single-ended drive circuits. Any noise present on the encode signal will result in additional aperture jitter that will be RMS summed with the inherent ADC aperture jitter. LTC2222/LTC2223 VDD TO INTERNAL ADC CIRCUITS 1.6V BIAS 6k ENC+ 0.1µF CLOCK INPUT 50Ω 1:4 VDD 1.6V BIAS 6k ENC– VDD Figure 11. Transformer Driven ENC+/ENC– 20 U In applications where jitter is critical (high input frequencies) take the following into consideration: 1. Differential drive should be used. 2. Use as large an amplitude as possible; if transformer coupled use a higher turns ratio to increase the amplitude. 3. If the ADC is clocked with a sinusoidal signal, filter the encode signal to reduce wideband noise. 4. Balance the capacitance and series resistance at both encode inputs so that any coupled noise will appear at both inputs as common mode noise. The encode inputs have a common mode range of 1.1V to 2.5V. Each input may be driven from ground to VDD for single-ended drive. Maximum and Minimum Encode Rates The maximum encode rate for the LTC2222/LTC2223 is 105Msps (LTC2222) and 80Msps (LTC2223). For the ADC to operate properly, the encode signal should have a 50% (±5%) duty cycle. Each half cycle must have at least 4.5ns (LTC2222) or 5.9ns (LTC2223) for the ADC internal circuitry to have enough settling time for proper operation. Achieving a precise 50% duty cycle is easy with differential sinusoidal drive using a transformer or using symmetric differential logic such as PECL or LVDS. An optional clock duty cycle stabilizer circuit can be used if the input clock has a non 50% duty cycle. This circuit uses the rising edge of the ENC+ pin to sample the analog input. The falling edge of ENC+ is ignored and the internal falling edge is generated by a phase-locked loop. The input clock duty cycle can vary from 20% to 80% and the clock duty cycle stabilizer will maintain a constant 50% internal duty cycle. If the clock is turned off for a long period of time, the duty cycle stabilizer circuit will require a hundred clock cycles for the PLL to lock onto the input clock. To use the clock duty cycle stabilizer, the MODE pin should be connected to 1/3VDD or 2/3VDD using external resistors. 22223 F11 W UU 22223fa LTC2222/LTC2223 APPLICATIO S I FOR ATIO The lower limit of the LTC2222/LTC2223 sample rate is determined by droop of the sample-and-hold circuits. The pipelined architecture of this ADC relies on storing analog signals on small valued capacitors. Junction leakage will discharge the capacitors. The specified minimum operating frequency for the LTC2222/LTC2223 is 1Msps. DIGITAL OUTPUTS Table 1 shows the relationship between the analog input voltage, the digital data bits and the overflow bit. Table 1. Output Codes vs Input Voltage AIN+ – AIN– (2V Range) >+1.000000V +0.999512V +0.999024V +0.000488V 0.000000V –0.000488V –0.000976V –0.999512V –1.000000V