LTC2402

LTC2401/LTC2402 1-/2-Channel 24-Bit µPower No Latency ∆ΣTMADCs in MSOP-10 FEATURES s s s s s s DESCRIPTIO s s s s s s s s s 24-Bit ADCs in Tiny MSOP-10 Packages 4ppm INL, No Missing Codes 4ppm Full-Scale Error 0.5ppm Offset 0.6ppm Noise Single Conversion Settling Time for Multiplexed Applications 1- or 2-Channel Inputs Automatic Channel Selection (Ping-Pong) (LTC2402) Zero Scale and Full Scale Set for Reference and Ground Sensing Internal Oscillator—No External Components Required 110dB Min, 50Hz/60Hz Notch Filter Reference Input Voltage: 0.1V to VCC Live Zero—Extended Input Range Accommodates 12.5% Overrange and Underrange Single Supply 2.7V to 5.5V Operation Low Supply Current (200µA) and Auto Shutdown The LTC®2401/LTC2402 are 1- and 2-channel 2.7V to 5.5V micropower 24-bit analog-to-digital converters with an integrated oscillator, 4ppm INL and 0.6ppm RMS noise. These ultrasmall devices use delta-sigma technology and a new digital filter architecture that settles in a single cycle. This eliminates the latency found in conventional ∆Σ converters and simplifies multiplexed applications. Through a single pin, the LTC2401/LTC2402 can be configured for better than 110dB rejection at 50Hz or 60Hz ± 2%, or can be driven by an external oscillator for a user defined rejection frequency in the range 1Hz to 120Hz. The internal oscillator requires no external frequency setting components. These converters accept an external reference voltage from 0.1V to VCC. With an extended input conversion range of –12.5% VREF to 112.5% VREF (VREF = FSSET – ZSSET), the LTC2401/LTC2402 smoothly resolve the offset and overrange problems of preceding sensors or signal conditioning circuits. The LTC2401/LTC2402 communicate through a 2- or 3-wire digital interface that is compatible with SPI and MICROWIRETM protocols. , LTC and LT are registered trademarks of Linear Technology Corporation. No Latency ∆Σ is a trademark of Linear Technology Corporation. MICROWIRE is a trademark of National Semiconductor Corporation. APPLICATIO S s s s s s s s Weight Scales Direct Temperature Measurement Gas Analyzers Strain Gauge Transducers Instrumentation Data Acquisition Industrial Process Control TYPICAL APPLICATIO 2.7V TO 5.5V 1µF 1 VCC LTC2402 REFERENCE VOLTAGE ZSSET + 0.1V TO VCC ANALOG INPUT RANGE ZSSET – 0.12VREF TO FSSET + 0.12VREF (VREF = FSSET – ZSSET) 0V TO FSSET – 100mV 2 3 4 5 FSSET CH1 CH0 ZSSET SCK SDO CS GND FO Pseudo Differential Bridge Digitizer 2.7V TO 5.5V VCC 10 = INTERNAL OSC/50Hz REJECTION = EXTERNAL CLOCK SOURCE = INTERNAL OSC/60Hz REJECTION 9 8 7 6 3-WIRE SPI INTERFACE 24012 TA01 U 1 2 4 3 5 VCC LTC2402 FSSET 9 SCK CH0 CH1 ZSSET GND 6 SDO CS FO 8 7 10 INTERNAL OSCILLATOR 60Hz REJECTION 3-WIRE SPI INTERFACE 24012TA02 U U 1 LTC2401/LTC2402 ABSOLUTE MAXIMUM RATINGS Supply Voltage (VCC) to GND .......................– 0.3V to 7V Analog Input Voltage to GND ....... – 0.3V to (VCC + 0.3V) Reference Input Voltage to GND .. – 0.3V to (VCC + 0.3V) Digital Input Voltage to GND ........ – 0.3V to (VCC + 0.3V) Digital Output Voltage to GND ..... – 0.3V to (VCC + 0.3V) PACKAGE/ORDER INFORMATION ORDER PART NUMBER TOP VIEW VCC FSSET VIN NC ZSSET 1 2 3 4 5 10 9 8 7 6 FO SCK SDO CS GND TOP VIEW LTC2401CMS LTC2401IMS MS10 PART MARKING LTMB LTMC MS10 PACKAGE 10-LEAD PLASTIC MSOP TJMAX = 125°C, θJA = 130°C/W Consult factory for Military grade parts. CONVERTER CHARACTERISTICS The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VREF = FSSET – ZSSET. (Notes 3, 4) CONDITIONS q PARAMETER Resolution No Missing Codes Resolution Integral Nonlinearity Offset Error Offset Error Drift Full-Scale Error Full-Scale Error Drift Total Unadjusted Error Output Noise Normal Mode Rejection 60Hz ± 2% Normal Mode Rejection 50Hz ± 2% Power Supply Rejection, DC Power Supply Rejection, 60Hz ± 2% Power Supply Rejection, 50Hz ± 2% 0.1V ≤ FSSET ≤ VCC, ZSSET = 0V (Note 5) FSSET = 2.5V, ZSSET = 0V (Note 6) FSSET = 5V, ZSSET = 0V (Note 6) 2.5V ≤ FSSET ≤ VCC, ZSSET = 0V 2.5V ≤ FSSET ≤ VCC, ZSSET = 0V 2.5V ≤ FSSET ≤ VCC, ZSSET = 0V 2.5V ≤ FSSET ≤ VCC, ZSSET = 0V FSSET = 2.5V, ZSSET = 0V FSSET = 5V, ZSSET = 0V VIN = 0V (Note 13) (Note 7) (Note 8) FSSET = 2.5V, ZSSET = 0V, VIN = 0V FSSET = 2.5V, ZSSET = 0V, VIN = 0V, (Notes 7, 15) FSSET = 2.5V, ZSSET = 0V, VIN = 0V, (Notes 8, 15) 2 U U W WW U W (Notes 1, 2) Operating Temperature Range LTC2401/LTC2402C ................................ 0°C to 70°C LTC2401/LTC2402I ............................ – 40°C to 85°C Storage Temperature Range ................. – 65°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300°C ORDER PART NUMBER VCC FSSET CH1 CH0 ZSSET 1 2 3 4 5 10 9 8 7 6 FO SCK SDO CS GND LTC2402CMS LTC2402IMS MS10 PART MARKING LTMD LTME MS10 PACKAGE 10-LEAD PLASTIC MSOP TJMAX = 125°C, θJA = 130°C/W U MIN 24 24 q q q q TYP MAX UNITS Bits Bits 2 4 0.5 0.01 4 0.04 5 10 3 10 15 2 10 ppm of VREF ppm of VREF ppm of VREF ppm of VREF/°C ppm of VREF ppm of VREF/°C ppm of VREF ppm of VREF µVRMS dB dB dB dB dB q q q 110 110 130 130 100 110 110 LTC2401/LTC2402 A ALOG I PUT A D REFERE CE SYMBOL VIN FSSET ZSSET CS(IN) CS(REF) IIN(LEAK) IREF(LEAK) PARAMETER Input Voltage Range Full-Scale Set Range Zero-Scale Set Range Input Sampling Capacitance Reference Sampling Capacitance Input Leakage Current Reference Leakage Current CS = VCC The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VREF = FSSET – ZSSET. (Note 3) CONDITIONS (Note 14) q q q VREF = 2.5V, CS = VCC DIGITAL I PUTS A D DIGITAL OUTPUTS SYMBOL VIH VIL VIH VIL IIN IIN CIN CIN VOH VOL VOH VOL IOZ PARAMETER High Level Input Voltage CS, FO Low Level Input Voltage CS, FO High Level Input Voltage SCK Low Level Input Voltage SCK Digital Input Current CS, FO Digital Input Current SCK Digital Input Capacitance CS, FO Digital Input Capacitance SCK High Level Output Voltage SDO Low Level Output Voltage SDO High Level Output Voltage SCK Low Level Output Voltage SCK High-Z Output Leakage SDO (Note 9) IO = – 800µA IO = 1.6mA IO = – 800µA (Note 10) IO = 1.6mA (Note 10) CONDITIONS 2.7V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 3.3V 4.5V ≤ VCC ≤ 5.5V 2.7V ≤ VCC ≤ 5.5V The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3) MIN q q q q q q 2.7V ≤ VCC ≤ 5.5V (Note 9) 2.7V ≤ VCC ≤ 3.3V (Note 9) 4.5V ≤ VCC ≤ 5.5V (Note 9) 2.7V ≤ VCC ≤ 5.5V (Note 9) 0V ≤ VIN ≤ VCC 0V ≤ VIN ≤ VCC (Note 9) POWER REQUIRE E TS SYMBOL VCC ICC PARAMETER Supply Voltage Supply Current Conversion Mode Sleep Mode The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3) CONDITIONS q CS = 0V (Note 12) CS = VCC (Note 12) U UW U U U U U MIN ZSSET – 0.12VREF 0.1 + ZSSET 0 TYP MAX FSSET + 0.12VREF VCC FSSET – 0.1 UNITS V V V pF pF 10 15 q q –10 – 12 1 1 10 12 nA nA TYP MAX UNITS V V 2.5 2.0 0.8 0.6 2.5 2.0 0.8 0.6 –10 –10 10 10 10 10 V V V V V V µA µA pF pF V q q q q q VCC – 0.5 0.4 VCC – 0.5 0.4 –10 10 V V V µA MIN 2.7 TYP MAX 5.5 UNITS V µA µA q q 200 20 300 30 3 LTC2401/LTC2402 TI I G CHARACTERISTICS SYMBOL fEOSC tHEO tLEO tCONV PARAMETER External Oscillator Frequency Range External Oscillator High Period External Oscillator Low Period Conversion Time F O = 0V FO = VCC External Oscillator (Note 11) Internal Oscillator (Note 10) External Oscillator (Notes 10, 11) (Note 10) (Note 9) (Note 9) (Note 9) Internal Oscillator (Notes 10, 12) External Oscillator (Notes 10, 11) (Note 9) q q q q q q q q The q denotes specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3) CONDITIONS q q q q q q fISCK DISCK fESCK tLESCK tHESCK tDOUT_ISCK tDOUT_ESCK t1 t2 t3 t4 tKQMAX tKQMIN t5 t6 Note 1: Absolute Maximum Ratings are those values beyond which the life of the device may be impaired. Note 2: All voltage values are with respect to GND. Note 3: VCC = 2.7 to 5.5V unless otherwise specified. Input source resistance = 0Ω. Note 4: Internal Conversion Clock source with the FO pin tied to GND or to VCC or to external conversion clock source with fEOSC = 153600Hz unless otherwise specified. Note 5: Guaranteed by design, not subject to test. Note 6: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band. Note 7: FO = 0V (internal oscillator) or fEOSC = 153600Hz ± 2% (external oscillator). Note 8: FO = VCC (internal oscillator) or fEOSC = 128000Hz ± 2% (external oscillator). 4 UW MIN 2.56 0.5 0.5 TYP MAX 307.2 390 390 UNITS kHz µs µs ms ms ms kHz kHz 130.86 133.53 136.20 157.03 160.23 163.44 20510/fEOSC (in kHz) 19.2 fEOSC/8 45 250 250 1.64 1.67 1.70 256/fEOSC (in kHz) 32/fESCK (in kHz) 0 0 0 50 200 15 50 50 150 150 150 55 2000 Internal SCK Frequency Internal SCK Duty Cycle External SCK Frequency Range External SCK Low Period External SCK High Period Internal SCK 32-Bit Data Output Time External SCK 32-Bit Data Output Time CS ↓ to SDO Low Z CS ↑ to SDO High Z CS ↓ to SCK ↓ CS ↓ to SCK ↑ SCK ↓ to SDO Valid SDO Hold After SCK ↓ SCK Set-Up Before CS ↓ SCK Hold After CS ↓ % kHz ns ns ms ms ms ns ns ns ns ns ns ns ns (Note 10) (Note 9) (Note 5) q q q q q q Note 9: The converter is in external SCK mode of operation such that the SCK pin is used as digital input. The frequency of the clock signal driving SCK during the data output is fESCK and is expressed in kHz. Note 10: The converter is in internal SCK mode of operation such that the SCK pin is used as digital output. In this mode of operation, the SCK pin has a total equivalent load capacitance CLOAD = 20pF. Note 11: The external oscillator is connected to the FO pin. The external oscillator frequency, fEOSC, is expressed in kHz. Note 12: The converter uses the internal oscillator. FO = 0V or FO = VCC. Note 13: The output noise includes the contribution of the internal calibration operations. Note 14: VREF = FSSET – ZSSET. The minimum input voltage is limited to – 0.3V and the maximum to VCC + 0.3V. Note 15: VCC (DC) = 4.1V, VCC (AC) = 2.8VP-P. LTC2401/LTC2402 TYPICAL PERFOR A CE CHARACTERISTICS Total Unadjusted Error (3V Supply) 10 VCC = 3V VREF = 2.5V 10 5 ERROR (ppm) ERROR (ppm) ERROR (ppm) TA = –55°C, –45°C, 25°C, 90°C 0 –5 125°C –10 0 0.5 1.5 2.0 1.0 INPUT VOLTAGE (V) Positive Extended Input Range Total Unadjusted Error (3V Supply) 10 VCC = 3V VREF = 2.5V 5 ERROR (ppm) TA = – 55°C, –45°C, 25°C, 90°C, 125°C 0 ERROR (ppm) 0 TA = –55°C, –45°C, 25°C, 90°C, 125°C ERROR (ppm) –5 –10 2.5 2.55 2.6 2.65 2.7 INPUT VOLTAGE (V) 2.75 2.8 Negative Extended Input Range Total Unadjusted Error (5V Supply) 10 TA = 90°C 5 TA = 25°C TA = 125°C 5 10 OFFSET ERROR (ppm) ERROR (ppm) ERROR (ppm) 0 TA = – 45°C TA = –55°C VCC = 5V VREF = 5V –5 –10 –0.3 –0.25 –0.2 –0.15 –0.1 INPUT VOLTAGE (V) UW 24012 G01 24012 G04 INL (3V Supply) VCC = 3V VREF = 2.5V 10 Negative Extended Input Range Total Unadjusted Error (3V Supply) TA = 25°C TA = 90°C 5 TA = 125°C 0 TA = – 45°C 5 0 125°C –5 TA = –55°C, –45°C, 25°C, 90°C –5 TA = –55°C VCC = 3V VREF = 2.5V 2.5 –10 0 0.5 1.5 2.0 1.0 INPUT VOLTAGE (V) 2.5 3.0 24012 G02 –10 –0.3 –0.25 –0.2 –0.15 –0.1 INPUT VOLTAGE (V) –0.05 0 24012 G03 Total Unadjusted Error (5V Supply) 10 VCC = 5V VREF = 5V 10 INL (5V Supply) VCC = 5V VREF = 5V TA = – 55°C, –45°C, 25°C, 90°C, 125°C 5 5 0 –5 –5 –10 –10 0 1 3 2 INPUT VOLTAGE (V) 4 5 24012 G05 0 0.5 1 1.5 2 2.5 3 3.5 INPUT VOLTAGE (V) 4 4.5 5 24012 G06 Positive Extended Input Range Total Unadjusted Error (5V Supply) VCC = 5V VREF = 5V 50 Offset Error vs Reference Voltage VCC = 5V TA = 25°C 40 30 0 TA = – 55°C TA = – 45°C TA = 90°C TA = 125°C TA = 25°C 5.25 5.3 20 –5 10 –10 –0.05 0 5.0 5.05 5.1 5.15 5.2 INPUT VOLTAGE (V) 0 0 1 3 4 2 REFERENCE VOLTAGE (V) 5 24012 G09 24012 G07 24012 G08 5 LTC2401/LTC2402 TYPICAL PERFOR A CE CHARACTERISTICS RMS Noise vs Reference Voltage 20 18 RMS NOISE (ppm OF VREF) 16 14 12 10 8 6 4 2 0 OFFSET ERROR (ppm) RMS NOISE (ppm) 0 1 3 4 2 REFERENCE VOLTAGE (V) Noise Histogram 350 VCC = 5V VREF = 5V 300 V = 0V IN RMS NOISE (ppm) NUMBER OF READINGS 250 200 150 100 50 0 –2 OFFSET ERROR (ppm) –1 0 1 OUTPUT CODE (ppm) 24012 G13 Full-Scale Error vs Temperature 5.0 VCC = 5V VREF = 5V VIN = 5V 60 50 FULL-SCALE ERROR (ppm) FULL-SCALE ERROR (ppm) 2.5 FULL-SCALE ERROR (ppm) 0 –2.5 –5.0 –55 –30 70 –5 20 45 TEMPERATURE (°C) 6 UW VCC = 5V TA = 25°C 24012 G10 Offset Error vs VCC 5.0 VREF = 2.5V TA = 25°C 5.0 RMS Noise vs VCC VREF = 2.5V TA = 25°C 2.5 0 2.5 –2.5 –5.0 5 2.7 3.2 3.7 4.2 VCC 4.7 5.2 24012 G11 0 2.7 3.2 3.7 4.2 VCC 4.7 5.2 24012 G12 RMS Noise vs Code Out 1.00 VCC = 5V VREF = 5V VIN = – 0.3V TO 5.3V TA = 25°C 5.0 Offset Error vs Temperature VCC = 5V VREF = 5V VIN = 0V 0.75 2.5 0.50 0 0.25 –2.5 2 3 0 –0.3 2.5 CODE OUT (HEX) 5.3 24012 G14 –5.0 –55 –30 70 –5 20 45 TEMPERATURE (°C) 95 120 24012 G15 Full-Scale Error vs Reference Voltage VCC = 5V VIN = VREF 6 5 4 3 2 1 0 Full-Scale Error vs VCC VREF = 2.5V VIN = 2.5V TA = 25°C 40 30 20 10 0 95 120 0 1 2 3 4 REFERENCE VOLTAGE (V) 5 24012 G17 2.7 3.2 3.7 4.2 VCC 4.7 5.2 24012 G18 24012 G16 LTC2401/LTC2402 TYPICAL PERFOR A CE CHARACTERISTICS Conversion Current vs Temperature 230 220 VCC = 5.5V SUPPLY CURRENT (µA) SUPPLY CURRENT (µA) 210 200 VCC = 4.1V 190 180 170 160 150 – 55 –30 –5 70 45 20 TEMPERATURE (°C) 95 120 VCC = 2.7V VCC = 5V REJECTION (dB) Rejection vs Frequency at VCC –40 VCC = 4.1V VIN = 0V TA = 25°C FO = 0 REJECTION (dB) –60 REJECTION (dB) REJECTION (dB) –80 –100 –120 0 50 150 200 100 FREQUENCY AT VCC (Hz) Rejection vs Frequency at VIN –60 –70 –80 0 –20 REJECTION (dB) REJECTION (dB) –90 –100 –110 –120 –130 REJECTION (dB) –140 –120 15100 –12 –8 –4 0 4 8 12 INPUT FREQUENCY DEVIATION FROM NOTCH FREQUENCY (%) 24012 G25 UW Sleep Current vs Temperature 30 –60 Rejection vs Frequency at VCC VCC = 4.1V VIN = 0V TA = 25°C FO = 0 20 VCC = 2.7V –75 –90 10 –105 0 –55 –30 –120 –5 20 45 70 TEMPERATURE (°C) 95 120 1 100 10k FREQUENCY AT VCC (Hz) 1M 24012 G21 24012 G19 24012 G20 Rejection vs Frequency at VCC –60 0 Rejection vs Frequency at VIN –20 –40 –60 –80 VCC = 5V VREF = 5V VIN = 2.5V FO = 0 –75 VCC = 4.1V VIN = 0V TA = 25°C FO = 0 –90 –105 –100 250 24012 G22 –120 15200 15250 15300 15350 15400 15450 15500 FREQUENCY AT VCC (Hz) 24012 G23 –120 1 50 100 150 200 FREQUENCY AT VIN (Hz) 250 24012 G24 Rejection vs Frequency at VIN VCC = 5V VREF = 5V VIN = 2.5V FO = 0 0 –20 –40 –60 –80 –100 –120 Rejection vs Frequency at VIN –40 –60 –80 –100 SAMPLE RATE = 15.36kHz ± 2% 15200 15300 15400 FREQUENCY AT VIN (Hz) 15500 24012 G26 –140 0 fS/2 INPUT FREQUENCY 24012 G27 fS 7 LTC2401/LTC2402 TYPICAL PERFOR A CE CHARACTERISTICS INL vs Output Rate 24 VCC = 5V VREF = 5V FO = EXTERNAL 20 RESOLUTION (BITS) INL (BITS) 16 TA = 90°C 12 TA = 25°C 8 0 20 PIN FUNCTIONS VCC (Pin 1): Positive Supply Voltage. Bypass to GND (Pin 6) with a 10µF tantalum capacitor in parallel with 0.1µF ceramic capacitor as close to the part as possible. FSSET (Pin 2): Full-Scale Set Input. This pin defines the full-scale input value. When VIN = FSSET, the ADC outputs full scale (FFFFFH). The total reference voltage is FSSET – ZSSET. CH0, CH1 (Pins 4, 3): Analog Input Channels. The input voltage range is – 0.125 • VREF to 1.125 • VREF. For VREF > 2.5V, the input voltage range may be limited by the absolute maximum rating of – 0.3V to VCC + 0.3V. Conversions are performed alternately between CH0 and CH1 for the LTC2402. Pin 4 is a No Connect (NC) on the LTC2401. ZSSET (Pin 5): Zero-Scale Set Input. This pin defines the zero-scale input value. When VIN = ZSSET, the ADC outputs zero scale (00000H). GND (Pin 6): Ground. Shared pin for analog ground, digital ground, reference ground and signal ground. Should be connected directly to a ground plane through a minimum length trace or it should be the single-point-ground in a single-point grounding system. CS (Pin 7): Active LOW Digital Input. A LOW on this pin enables the SDO digital output and wakes up the ADC. Following each conversion, the ADC automatically enters the Sleep mode and remains in this low power state as long as CS is HIGH. A LOW on CS wakes up the ADC. A LOW-to-HIGH transition on this pin disables the SDO digital output. A LOW-to-HIGH transition on CS during the Data Output transfer aborts the data transfer and starts a new conversion. SDO (Pin 8): Three-State Digital Output. During the data output period, this pin is used for serial data output. When the chip select CS is HIGH (CS = VCC), the SDO pin is in a high impedance state. During the Conversion and Sleep periods, this pin can be used as a conversion status output. The conversion status can be observed by pulling CS LOW. 8 UW Resolution vs Output Rate 24 20 TA = 90°C TA = 25°C 16 TA = – 55°C TA = – 55°C 12 VCC = 5V VREF = 5V FO = EXTERNAL 80 100 24012 G28 60 40 OUTPUT RATE (Hz) 8 0 20 60 40 OUTPUT RATE (Hz) 80 100 24012 G29 U U U LTC2401/LTC2402 PIN FUNCTIONS SCK (Pin 9): Bidirectional Digital Clock Pin. In the Internal Serial Clock Operation mode, SCK is used as digital output for the internal serial interface clock during the data output period. In the External Serial Clock Operation mode, SCK is used as digital input for the external serial interface. An internal pull-up current source is automatically activated in Internal Serial Clock Operation mode. The Serial Clock mode is determined by the level applied to SCK at power up and the falling edge of CS. FO (Pin 10): Frequency Control Pin. Digital input that controls the ADC’s notch frequencies and conversion time. When the FO pin is connected to VCC (FO = VCC), the converter uses its internal oscillator and the digital filter’s first null is located at 50Hz. When the FO pin is connected to GND (FO = 0V), the converter uses its internal oscillator and the digital filter’s first null is located at 60Hz. When FO is driven by an external clock signal with a frequency fEOSC, the converter uses this signal as its clock and the digital filter first null is located at a frequency fEOSC/2560. FUNCTIONAL BLOCK DIAGRA VCC GND VIN ∫ ∫ ∫ ∑ ADC SERIAL INTERFACE DECIMATING FIR VREF DAC TEST CIRCUITS VCC 3.4k SDO 3.4k CLOAD = 20pF Hi-Z TO VOH VOL TO VOH VOH TO Hi-Z 24012 TC01 W U U U U U INTERNAL OSCILLATOR AUTOCALIBRATION AND CONTROL FO (INT/EXT) SDO SCK CS 24012 FD SDO CLOAD = 20pF Hi-Z TO VOL VOH TO VOL VOL TO Hi-Z 24012 TC02 9 LTC2401/LTC2402 APPLICATIO S I FOR ATIO Converter Operation Cycle The LTC2401/LTC2402 are low power, delta-sigma analog-to-digital converters with an easy to use 3-wire serial interface. Their operation is simple and made up of three states. The converter operating cycle begins with the conversion, followed by a low power sleep state and concluded with the data output (see Figure 1). The 3-wire interface consists of serial data output (SDO), a serial clock (SCK) and a chip select (CS). Initially, the LTC2401/LTC2402 perform a conversion. Once the conversion is complete, the device enters the sleep state. While in this sleep state, power consumption is reduced by an order of magnitude. The part remains in the sleep state as long as CS is logic HIGH. The conversion result is held indefinitely in a static shift register while the converter is in the sleep state. Once CS is pulled low, the device begins outputting the conversion result. There is no latency in the conversion result. The data output corresponds to the conversion just performed. This result is shifted out on the serial data out pin (SDO) under the control of the serial clock (SCK). Data is updated on the falling edge of SCK allowing the user to reliably latch data on the rising edge of SCK, see Figure 3. The data output state is concluded once 32 bits are read out of the ADC or when CS is brought HIGH. The device automatically initiates a new conversion cycle and the cycle repeats. CONVERT SLEEP 1 CS AND SCK 0 DATA OUTPUT 24012 F01 Figure 1. LTC2401/LTC2402 State Transition Diagram 10 U Through timing control of the CS and SCK pins, the LTC2401/LTC2402 offer several flexible modes of operation (internal or external SCK and free-running conversion modes). These various modes do not require programming configuration registers; moreover, they do not disturb the cyclic operation described above. These modes of operation are described in detail in the Serial Interface Timing Modes section. Conversion Clock A major advantage delta-sigma converters offer over conventional type converters is an on-chip digital filter (commonly known as Sinc or Comb filter). For high resolution, low frequency applications, this filter is typically designed to reject line frequencies of 50Hz or 60Hz plus their harmonics. In order to reject these frequencies in excess of 110dB, a highly accurate conversion clock is required. The LTC2401/LTC2402 incorporate an on-chip highly accurate oscillator. This eliminates the need for external frequency setting components such as crystals or oscillators. Clocked by the on-chip oscillator, the LTC2401/ LTC2402 reject line frequencies (50Hz or 60Hz ± 2%) a minimum of 110dB. Ease of Use The LTC2401/LTC2402 data output has no latency, filter settling or redundant data associated with the conversion cycle. There is a one-to-one correspondence between the conversion and the output data. Therefore, multiplexing an analog input voltage is easy. The LTC2401/LTC2402 perform offset and full-scale calibrations every conversion cycle. This calibration is transparent to the user and has no effect on the cyclic operation described above. The advantage of continuous calibration is extreme stability of offset and full-scale readings with respect to time, supply voltage change and temperature drift. Power-Up Sequence The LTC2401/LTC2402 automatically enter an internal reset state when the power supply voltage VCC drops below approximately 2.2V. This feature guarantees the W UU LTC2401/LTC2402 APPLICATIO S I FOR ATIO integrity of the conversion result and of the serial interface mode selection which is performed at the initial power-up. (See the 2-wire I/O sections in the Serial Interface Timing Modes section.) When the VCC voltage rises above this critical threshold, the converter creates an internal power-on-reset (POR) signal with duration of approximately 0.5ms. The POR signal clears all internal registers. Following the POR signal, the LTC2401/LTC2402 start a normal conversion cycle and follows the normal succession of states described above. The first conversion result following POR is accurate within the specifications of the device. Reference Voltage Range The LTC2401/LTC2402 can accept a reference voltage (VREF = FSSET – ZSSET) from 0V to VCC. The converter output noise is determined by the thermal noise of the front-end circuits, and as such, its value in microvolts is nearly constant with reference voltage. A decrease in reference voltage will not significantly improve the converter’s effective resolution. On the other hand, a reduced reference voltage will improve the overall converter INL performance. The recommended range for the LTC2401/LTC2402 voltage reference is 100mV to VCC. Input Voltage Range The converter is able to accommodate system level offset and gain errors as well as system level overrange situations due to its extended input range, see Figure 2. The LTC2401/LTC2402 convert input signals within the extended input range of – 0.125 • VREF to 1.125 • VREF (VREF = FSSET – ZSSET). For large values of VREF (VREF = FSSET – ZSSET), this range is limited by the absolute maximum voltage range of – 0.3V to (VCC + 0.3V). Beyond this range, the input ESD protection devices begin to turn on and the errors due to the input leakage current increase rapidly. Input signals applied to VIN may extend below ground by – 300mV and above VCC by 300mV. In order to limit any fault current, a resistor of up to 5k may be added in series with the VIN pin without affecting the performance of the device. In the physical layout, it is important to maintain U VCC + 0.3V FSSET + 0.12VREF FSSET ABSOLUTE MAXIMUM INPUT RANGE NORMAL INPUT RANGE EXTENDED INPUT RANGE ZSSET ZSSET – 0.12VREF –0.3V (VREF = FSSET – ZSSET) 24012 F02 W UU Figure 2. LTC2401/LTC2402 Input Range the parasitic capacitance of the connection between this series resistance and the VIN pin as low as possible; therefore, the resistor should be located as close as practical to the VIN pin. The effect of the series resistance on the converter accuracy can be evaluated from the curves presented in the Analog Input/Reference Current section. In addition, a series resistor will introduce a temperature dependent offset error due to the input leakage current. A 1nA input leakage current will develop a 1ppm offset error on a 5k resistor if VREF = 5V. This error has a very strong temperature dependency. Output Data Format The LTC2401/LTC2402 serial output data stream is 32 bits long. The first 4 bits represent status information indicating the sign, selected channel, input range and conversion state. The next 24 bits are the conversion result, MSB first. The remaining 4 bits are sub LSBs beyond the 24-bit level that may be included in averaging or discarded without loss of resolution. Bit 31 (first output bit) is the end of conversion (EOC) indicator. This bit is available at the SDO pin during the conversion and sleep states whenever the CS pin is LOW. This bit is HIGH during the conversion and goes LOW when the conversion is complete. Bit 30 (second output bit) for the LTC2402, this bit is LOW if the last conversion was performed on CH0 and HIGH for CH1. This bit is always low for the LTC2401. 11 LTC2401/LTC2402 APPLICATIO S I FOR ATIO Bit 29 (third output bit) is the conversion result sign indicator (SIG). If VIN is >0, this bit is HIGH. If VIN is VREF or VIN < 0, this bit is HIGH. The function of these bits is summarized in Table 1. Table 1. LTC2401/LTC2402 Status Bits Input Range VIN > VREF 0 < VIN ≤ VREF VIN = 0+/0 – VIN < 0 Bit 31 EOC 0 0 0 0 Bit 30 CH0/CH1 0/1 0/1 0/1 0/1 Bit 29 SIG 1 1 1/0 0 Bit 28 EXR 1 0 0 1 Bit 27 (fifth output bit) is the most significant bit (MSB). Bits 27-4 are the 24-bit conversion result MSB first. Bit 4 is the least significant bit (LSB). Bits 3-0 are sub LSBs below the 24-bit level. Bits 3-0 may be included in averaging or discarded without loss of resolution. Data is shifted out of the SDO pin under control of the serial clock (SCK), see Figure 3. Whenever CS is HIGH, SDO remains high impedance and any SCK clock pulses are ignored by the internal data out shift register. In order to shift the conversion result out of the device, CS must first be driven LOW. EOC is seen at the SDO pin of the device once CS is pulled LOW. EOC changes real time from CS BIT 31 SDO Hi-Z EOC BIT 30 CH0/CH1 BIT 29 SIG SCK 1 SLEEP 2 Figure 3. Output Data Timing 12 U HIGH to LOW at the completion of a conversion. This signal may be used as an interrupt for an external microcontroller. Bit 31 (EOC) can be captured on the first rising edge of SCK. Bit 30 is shifted out of the device on the first falling edge of SCK. The final data bit (Bit 0) is shifted out on the falling edge of the 31st SCK and may be latched on the rising edge of the 32nd SCK pulse. On the falling edge of the 32nd SCK pulse, SDO goes HIGH indicating a new conversion cycle has been initiated. This bit serves as EOC (Bit 31) for the next conversion cycle. Table 2 summarizes the output data format. As long as the voltage on the VIN pin is maintained within the – 0.3V to (VCC + 0.3V) absolute maximum operating range, a conversion result is generated for any input value from – 0.125 • VREF to 1.125 • VREF. For input voltages greater than 1.125 • VREF, the conversion result is clamped to the value corresponding to 1.125 • VREF. For input voltages below – 0.125 • VREF, the conversion result is clamped to the value corresponding to – 0.125 • VREF. Frequency Rejection Selection (FO Pin Connection) The LTC2401/LTC2402 internal oscillator provides better than 110dB normal mode rejection at the line frequency and all its harmonics for 50Hz ± 2% or 60Hz ± 2%. For 60Hz rejection, FO (Pin 10) should be connected to GND (Pin 6) while for 50Hz rejection the FO pin should be connected to VCC (Pin 1). The selection of 50Hz or 60Hz rejection can also be made by driving FO to an appropriate logic level. A selection change during the sleep or data output states will not BIT 28 EXT BIT 27 MSB BIT 4 LSB24 BIT 0 3 4 5 27 28 32 CONVERSION 24012 F03 W UU DATA OUTPUT LTC2401/LTC2402 APPLICATIO S I FOR ATIO Table 2. LTC2401/LTC2402 Output Data Format Input Voltage VIN > 9/8 • VREF 9/8 • VREF VREF + 1LSB VREF 3/4VREF + 1LSB 3/4VREF 1/2VREF + 1LSB 1/2VREF 1/4VREF + 1LSB 1/4VREF 0+/0 – –1LSB –1/8 • VREF VIN < –1/8 • VREF Bit 31 EOC 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 30 CH SELECT CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 CH0/CH1 Bit 29 SIG 1 1 1 1 1 1 1 1 1 1 1/0** 0 0 0 Bit 28 EXR 1 1 1 0 0 0 0 0 0 0 0 1 1 1 *The sub LSBs are valid conversion results beyond the 24-bit level that may be included in averaging or discarded without loss of resolution. **The sign bit changes state during the 0 code. disturb the converter operation. If the selection is made during the conversion state, the result of the conversion in progress may be outside specifications but the following conversions will not be affected. When a fundamental rejection frequency different from 50Hz or 60Hz is required or when the converter must be synchronized with an outside source, the LTC2401/ LTC2402 can operate with an external conversion clock. The converter automatically detects the presence of an external clock signal at the FO pin and turns off the internal oscillator. The frequency fEOSC of the external signal must be at least 2560Hz (1Hz notch frequency) to be detected. The external clock signal duty cycle is not significant as long as the minimum and maximum specifications for the high and low periods tHEO and tLEO are observed. While operating with an external conversion clock of a frequency fEOSC, the LTC2401/LTC2402 provide better than 110dB normal mode rejection in a frequency range fEOSC/2560 ± 4% and its harmonics. The normal mode rejection as a function of the input frequency deviation from fEOSC/2560 is shown in Figure 4. REJECTION (dB) U Bit 27 MSB 0 0 0 1 1 1 1 0 0 0 0 1 1 1 Bit 26 0 0 0 1 1 0 0 1 1 0 0 1 1 1 Bit 25 0 0 0 1 0 1 0 1 0 1 0 1 1 1 Bit 24 1 1 0 1 0 1 0 1 0 1 0 1 0 0 Bit 23 1 1 0 1 0 1 0 1 0 1 0 1 0 0 … ... ... ... ... ... ... ... ... ... ... ... ... ... ... Bit 4 LSB 1 1 0 1 0 1 0 1 0 1 0 1 0 0 Bit 3-0 SUB LSBs* X X X X X X X X X X X X X X W UU Whenever an external clock is not present at the FO pin, the converter automatically activates its internal oscillator and enters the Internal Conversion Clock mode. The LTC2401/ LTC2402 operation will not be disturbed if the change of conversion clock source occurs during the sleep state or during the data output state while the converter uses an –60 –70 –80 –90 –100 –110 –120 –130 –140 –12 –8 –4 0 4 8 12 INPUT FREQUENCY DEVIATION FROM NOTCH FREQUENCY (%) 24012 F04 Figure 4. LTC2401/LTC2402 Normal Mode Rejection When Using an External Oscillator of Frequency fEOSC 13 LTC2401/LTC2402 APPLICATIO S I FOR ATIO external serial clock. If the change occurs during the conversion state, the result of the conversion in progress may be outside specifications but the following conversions will not be affected. If the change occurs during the data output state and the converter is in the Internal SCK mode, the serial clock duty cycle may be affected but the serial data stream will remain valid. Table 3 summarizes the duration of each state as a function of FO. SERIAL INTERFACE The LTC2401/LTC2402 transmit the conversion results and receives the start of conversion command through a synchronous 3-wire interface. During the conversion and sleep states, this interface can be used to assess the converter status and during the data output state it is used to read the conversion result. Serial Clock Input/Output (SCK) The serial clock signal present on SCK (Pin 9) is used to synchronize the data transfer. Each bit of data is shifted out the SDO pin on the falling edge of the serial clock. In the Internal SCK mode of operation, the SCK pin is an output and the LTC2401/LTC2402 create their own serial clock by dividing the internal conversion clock by 8. In the External SCK mode of operation, the SCK pin is used as Table 3. LTC2401/LTC2402 State Duration State CONVERT Operating Mode Internal Oscillator FO = LOW (60Hz Rejection) FO = HIGH (50Hz Rejection) External Oscillator FO = External Oscillator with Frequency fEOSC kHz (fEOSC/2560 Rejection) FO = LOW/HIGH (Internal Oscillator) FO = External Oscillator with Frequency fEOSC kHz SLEEP DATA OUTPUT Internal Serial Clock External Serial Clock with Frequency fSCK kHz 14 U input. The internal or external SCK mode is selected on power-up and then reselected every time a HIGH-to-LOW transition is detected at the CS pin. If SCK is HIGH or floating at power-up or during this transition, the converter enters the internal SCK mode. If SCK is LOW at power-up or during this transition, the converter enters the external SCK mode. Serial Data Output (SDO) The serial data output pin, SDO (Pin 8), drives the serial data during the data output state. In addition, the SDO pin is used as an end of conversion indicator during the conversion and sleep states. When CS (Pin 7) is HIGH, the SDO driver is switched to a high impedance state. This allows sharing the serial interface with other devices. If CS is LOW during the convert or sleep state, SDO will output EOC. If CS is LOW during the conversion phase, the EOC bit appears HIGH on the SDO pin. Once the conversion is complete, EOC goes LOW. The device remains in the sleep state until the first rising edge of SCK occurs while CS = 0. Chip Select Input (CS) The active LOW chip select, CS (Pin 7), is used to test the conversion status and to enable the data output transfer as described in the previous sections. Duration 133ms 160ms 20510/fEOSCs As Long As CS = HIGH Until CS = 0 and SCK As Long As CS = LOW But Not Longer Than 1.67ms (32 SCK cycles) As Long As CS = LOW But Not Longer Than 256/fEOSCms (32 SCK cycles) As Long As CS = LOW But Not Longer Than 32/fSCKms (32 SCK cycles) W UU LTC2401/LTC2402 APPLICATIO S I FOR ATIO In addition, the CS signal can be used to trigger a new conversion cycle before the entire serial data transfer has been completed. The LTC2401/LTC2402 will abort any serial data transfer in progress and start a new conversion cycle anytime a LOW-to-HIGH transition is detected at the CS pin after the converter has entered the data output state (i.e., after the first rising edge of SCK occurs with CS = 0). Finally, CS can be used to control the free-running modes of operation, see Serial Interface Timing Modes section. Grounding CS will force the ADC to continuously convert at the maximum output rate selected by FO. Tying a capacitor to CS will reduce the output rate and power dissipation by a factor proportional to the capacitor’s value, see Figures 12 to 14. SERIAL INTERFACE TIMING MODES The LTC2401/LTC2402’s 3-wire interface is SPI and MICROWIRE compatible. This interface offers several flexible modes of operation. These include internal/external serial clock, 2- or 3-wire I/O, single cycle conversion and autostart. The following sections describe each of these serial interface timing modes in detail. In all these cases, the converter can use the internal oscillator (FO = LOW or FO = HIGH) or an external oscillator connected to the FO pin. Refer to Table 4 for a summary. External Serial Clock, Single Cycle Operation (SPI/MICROWIRE Compatible) This timing mode uses an external serial clock to shift out the conversion result and a CS signal to monitor and control the state of the conversion cycle, see Figure 5. Table 4. LTC2401/LTC2402 Interface Timing Modes SCK Source External External Internal Internal Internal Conversion Cycle Control CS and SCK SCK CS ↓ Continuous CEXT Data Output Control CS and SCK SCK CS ↓ Internal Internal Connection and Waveforms Figures 5, 6 Figure 7 Figures 8, 9 Figure 10 Figure 11 Configuration External SCK, Single Cycle Conversion External SCK, 2-Wire I/O Internal SCK, Single Cycle Conversion Internal SCK, 2-Wire I/O, Continuous Conversion Internal SCK, Autostart Conversion U The serial clock mode is selected on the falling edge of CS. To select the external serial clock mode, the serial clock pin (SCK) must be LOW during each CS falling edge. The serial data output pin (SDO) is Hi-Z as long as CS is HIGH. At any time during the conversion cycle, CS may be pulled LOW in order to monitor the state of the converter. While CS is pulled LOW, EOC is output to the SDO pin. EOC = 1 while a conversion is in progress and EOC = 0 if the device is in the sleep state. Independent of CS, the device automatically enters the low power sleep state once the conversion is complete. When the device is in the sleep state (EOC = 0), its conversion result is held in an internal static shift register. The device remains in the sleep state until the first rising edge of SCK is seen while CS is LOW. Data is shifted out the SDO pin on each falling edge of SCK. This enables external circuitry to latch the output on the rising edge of SCK. EOC can be latched on the first rising edge of SCK and the last bit of the conversion result can be latched on the 32nd rising edge of SCK. On the 32nd falling edge of SCK, the device begins a new conversion. SDO goes HIGH (EOC = 1) indicating a conversion is in progress. At the conclusion of the data cycle, CS may remain LOW and EOC monitored as an end-of-conversion interrupt. Alternatively, CS may be driven HIGH setting SDO to Hi-Z. As described above, CS may be pulled LOW at any time in order to monitor the conversion status. Typically, CS remains LOW during the data output state. However, the data output state may be aborted by pulling CS HIGH anytime between the first rising edge and the 32nd falling edge of SCK, see Figure 6. On the rising edge W UU 15 LTC2401/LTC2402 APPLICATIO S I FOR ATIO REFERENCE VOLTAGE ZSSET + 0.1V TO VCC ANALOG INPUT RANGE ZSSET – 0.12VREF TO FSSET + 0.12VREF (VREF = FSSET – ZSSET) 0V TO FSSET – 100mV CS TEST EOC SDO Hi-Z Hi-Z TEST EOC TEST EOC BIT 31 EOC BIT 30 CH0/CH1 SCK (EXTERNAL) CONVERSION SLEEP DATA OUTPUT CONVERSION 24012 F05 Figure 5. External Serial Clock, Single Cycle Operation REFERENCE VOLTAGE ZSSET + 0.1V TO VCC ANALOG INPUT RANGE ZSSET – 0.12VREF TO FSSET + 0.12VREF (VREF = FSSET – ZSSET) 0V TO FSSET – 100mV CS TEST EOC TEST EOC TEST EOC BIT 0 SDO EOC Hi-Z Hi-Z Hi-Z SCK (EXTERNAL) SLEEP CONVERSION DATA OUTPUT SLEEP DATA OUTPUT CONVERSION 24012 F06 Figure 6. External Serial Clock, Reduced Data Output Length 16 U 2.7V TO 5.5V 1µF 1 VCC LTC2402 2 3 4 5 FSSET CH1 CH0 ZSSET SCK SDO CS GND 9 8 7 6 3-WIRE SERIAL I/O FO 10 VCC W UU = INTERNAL OSC/50Hz REJECTION = EXTERNAL CLOCK SOURCE = INTERNAL OSC/60Hz REJECTION BIT 29 BIT 28 EXR BIT 27 MSB BIT 26 BIT 4 LSB BIT 0 SUB LSB Hi-Z 2.7V TO 5.5V 1µF 1 VCC LTC2402 2 3 4 5 FSSET CH1 CH0 ZSSET SCK SDO CS GND 9 8 7 6 3-WIRE SERIAL I/O FO 10 VCC = INTERNAL OSC/50Hz REJECTION = EXTERNAL CLOCK SOURCE = INTERNAL OSC/60Hz REJECTION BIT 31 EOC BIT 30 CH0/CH1 BIT 29 SIG BIT 28 EXR BIT 27 MSB BIT 9 BIT 8 Hi-Z LTC2401/LTC2402 APPLICATIO S I FOR ATIO of CS, the device aborts the data output state and immediately initiates a new conversion. This is useful for systems not requiring all 32 bits of output data, aborting an invalid conversion cycle or synchronizing the start of a conversion. External Serial Clock, 2-Wire I/O This timing mode utilizes a 2-wire serial I/O interface. The conversion result is shifted out of the device by an externally generated serial clock (SCK) signal, see Figure 7. CS may be permanently tied to ground (Pin 6), simplifying the user interface or isolation barrier. The external serial clock mode is selected at the end of the power-on reset (POR) cycle. The POR cycle is concluded approximately 0.5ms after VCC exceeds 2.2V. The level applied to SCK at this time determines if SCK is internal or external. SCK must be driven LOW prior to the end of POR in order to enter the external serial clock timing mode. Since CS is tied LOW, the end-of-conversion (EOC) can be continuously monitored at the SDO pin during the convert and sleep states. EOC may be used as an interrupt to an external controller indicating the conversion result is ready. EOC = 1 while the conversion is in 2.7V TO 5.5V 1µF 1 REFERENCE VOLTAGE ZSSET + 0.1V TO VCC ANALOG INPUT RANGE ZSSET – 0.12VREF TO FSSET + 0.12VREF (VREF = FSSET – ZSSET) 0V TO FSSET – 100mV CS BIT 31 SDO EOC BIT 30 CH0/CH1 SCK (EXTERNAL) CONVERSION SLEEP DATA OUTPUT CONVERSION 24012 F07 Figure 7. External Serial Clock, CS = 0 Operation U progress and EOC = 0 once the conversion enters the low power sleep state. On the falling edge of EOC, the conversion result is loaded into an internal static shift register. The device remains in the sleep state until the first rising edge of SCK. Data is shifted out the SDO pin on each falling edge of SCK enabling external circuitry to latch data on the rising edge of SCK. EOC can be latched on the first rising edge of SCK. On the 32nd falling edge of SCK, SDO goes HIGH (EOC = 1) indicating a new conversion has begun. Internal Serial Clock, Single Cycle Operation This timing mode uses an internal serial clock to shift out the conversion result and a CS signal to monitor and control the state of the conversion cycle, see Figure 8. In order to select the internal serial clock timing mode, the serial clock pin (SCK) must be floating (Hi-Z) or pulled HIGH prior to the falling edge of CS. The device will not enter the internal serial clock mode if SCK is driven LOW on the falling edge of CS. An internal weak pull-up resistor is active on the SCK pin during the falling edge of CS; therefore, the internal serial clock timing mode is automatically selected if SCK is not externally driven. VCC W UU VCC LTC2402 FO 10 = INTERNAL OSC/50Hz REJECTION = EXTERNAL CLOCK SOURCE = INTERNAL OSC/60Hz REJECTION 2 3 4 5 FSSET CH1 CH0 ZSSET SCK SDO CS GND 9 8 7 6 2-WIRE SERIAL I/O BIT 29 SIG BIT 28 EXR BIT 27 MSB BIT 26 BIT 4 LSB24 BIT 0 17 LTC2401/LTC2402 APPLICATIO S I FOR ATIO REFERENCE VOLTAGE ZSSET + 0.1V TO VCC ANALOG INPUT RANGE ZSSET – 0.12VREF TO FSSET + 0.12VREF (VREF = FSSET – ZSSET) 0V TO FSSET – 100mV tEOCtest CS TEST EOC TEST EOC (VCC – 0.4V)]. Severe ground pin current disturbances can also occur due to the undershoot of fast digital input signals. Undershoot and overshoot can occur because of the impedance mismatch at the converter pin when the transition time of an external control signal is less than twice the propagation delay from the driver to LTC2401/LTC2402. For W UU LTC2401/LTC2402 APPLICATIO S I FOR ATIO reference, on a regular FR-4 board, signal propagation velocity is approximately 183ps/inch for internal traces and 170ps/inch for surface traces. Thus, a driver generating a control signal with a minimum transition time of 1ns must be connected to the converter pin through a trace shorter than 2.5 inches. This problem becomes particularly difficult when shared control lines are used and multiple reflections may occur. The solution is to carefully terminate all transmission lines close to their characteristic impedance. Parallel termination near the LTC2401/LTC2402 pin will eliminate this problem but will increase the driver power dissipation. A series resistor between 27Ω and 56Ω placed near the driver or near the LTC2401/LTC2402 pin will also eliminate this problem without additional power dissipation. The actual resistor value depends upon the trace impedance and connection topology. Driving the Input and Reference The analog input and reference of the typical delta-sigma analog-to-digital converter are applied to a switched capacitor network. This network consists of capacitors switching between the analog input (VIN), ZSSET (Pin 5) and FSSET (Pin 2). The result is small current spikes seen at both VIN and VREF. A simplified input equivalent circuit is shown in Figure 15. The key to understanding the effects of this dynamic input current is based on a simple first order RC time constant model. Using the internal oscillator, the VCC IREF(LEAK) FSSET IREF(LEAK) IIN CH0/CH1 IIN(LEAK) RSW 5k ZSSET 24012 F15 RSW 5k VCC IIN(LEAK) RSW 5k AVERAGE INPUT CURRENT: IIN = 0.25(VIN – 0.5 • VREF)fCEQ CEQ 2.5pF (TYP) SWITCHING FREQUENCY f = 153.6kHz FOR INTERNAL OSCILLATOR (fO = LOGIC LOW OR HIGH) f = fEOSC FOR EXTERNAL OSCILLATORS Figure 15. LTC2401/LTC2402 Equivalent Analog Input Circuit U LTC2401/LTC2402’s internal switched capacitor network is clocked at 153,600Hz corresponding to a 6.5µs sampling period. Fourteen time constants are required each time a capacitor is switched in order to achieve 1ppm settling accuracy. Therefore, the equivalent time constant at VIN and VREF should be less than 6.5µs/14 = 460ns in order to achieve 1ppm accuracy. Input Current (VIN) If complete settling occurs on the input, conversion results will be uneffected by the dynamic input current. If the settling is incomplete, it does not degrade the linearity performance of the device. It simply results in an offset/ full-scale shift, see Figure 16. To simplify the analysis of input dynamic current, two separate cases are assumed: large capacitance at VIN (CIN > 0.01µF) and small capacitance at VIN (CIN < 0.01µF). TUE ZSSET VIN FSSET 24012 F16 W UU Figure 16. Offset/Full-Scale Shift If the total capacitance at VIN (see Figure 17) is small (< 0.01µF), relatively large external source resistances (up to 20k for 20pF parasitic capacitance) can be tolerated without any offset/full-scale error. Figures 18 and 19 show a family of offset and full-scale error curves for various small valued input capacitors (CIN < 0.01µF) as a function of input source resistance. For large input capacitor values (CIN > 0.01µF), the input spikes are averaged by the capacitor into a DC current. The gain shift becomes a linear function of input source 23 LTC2401/LTC2402 APPLICATIO S I FOR ATIO RSOURCE VIN INTPUT SIGNAL SOURCE CPAR ≅ 20pF CIN FULL-SCALE ERROR (ppm) LTC2401/ LTC2402 24012 F17 Figure 17. An RC Network at VIN 50 40 OFFSET ERROR (ppm) VCC = 5V VREF = 5V VIN = 0V TA = 25°C CIN = 0.01µF CIN = 1000pF 30 20 10 0 –10 FULL-SCALE (ppm) 1 10 100 1k RSOURCE (Ω) 10k 100k 24012 F18 CIN = NO CAP CIN = 100pF Figure 18. Offset vs RSOURCE (Small C) 80 CIN = 22µF CIN = 10µF CIN = 1µF CIN = 0.1µF CIN = 0.01µF CIN = 0.001µF OFFSET ERROR (ppm) 60 VCC = 5V 40 VREF = 5V VIN = 0V TA = 25°C 20 0 0 200 600 400 RSOURCE (Ω) 800 1000 24012 F19 Figure 19. Offset vs RSOURCE (Large C) resistance independent of input capacitance, see Figures 20 and 21. The equivalent input impedance is 6.25MΩ. This results in ± 400µA of input dynamic current at the extreme values of VIN (VIN = 0V and VIN = VREF, when VREF = 5V). This corresponds to a 0.8ppm shift in offset and full-scale readings for every 10Ω of input source resistance. 24 U 10 0 –10 –20 –30 –40 –50 –60 –70 –80 0 200 600 400 RSOURCE (Ω) 800 1000 CIN = 22µF CIN = 10µF CIN = 1µF CIN = 0.1µF CIN = 0.01µF CIN = 0.001µF VCC = 5V VREF = 5V VIN = 5V TA = 25°C 24012 F20 W UU Figure 20. Full-Scale Error vs RSOURCE (Large C) 30 VCC = 5V VREF = 5V VIN = 5V TA = 25°C CIN = NO CAP 10 –10 CIN = 0.01µF CIN = 1000pF –30 CIN = 100pF –50 0 10 1k 100 RSOURCE (Ω) 10k 100k 24012 F21 Figure 21. Full-Scale Error vs RSOURCE (Small C) In addition to the input current spikes, the input ESD protection diodes have a temperature dependent leakage current. This leakage current, nominally 1nA (±10nA max), results in a fixed offset shift of 10µV for a 10k source resistance. The effect of input leakage current is evident for CIN = 0 in Figures 18 and 21. A leakage current of 3nA results in a 150µV (30ppm) error for a 50k source resistance. As RSOURCE gets larger, the switched capacitor input current begins to dominate. Reference Current (VREF) Similar to the analog input, the reference input has a dynamic input current. This current has negligible effect LTC2401/LTC2402 APPLICATIO S I FOR ATIO on the offset. However, the reference current at VIN = VREF is similar to the input current at full-scale. For large values of reference capacitance (CVREF > 0.01µF), the full-scale error shift is 0.08ppm/Ω of external reference resistance independent of the capacitance at VREF, see Figure 22. If the capacitance tied to VREF is small (CVREF < 0.01µF), an input resistance of up to 20k (20pF parasitic capacitance at VREF) may be tolerated, see Figure 23. Unlike the analog input, the integral nonlinearity of the device can be degraded with excessive external RC time constants tied to the reference input. If the capacitance 160 FULL-SCALE ERROR (ppm) VCC = 5V VREF = 5V VIN = 5V 120 TA = 25°C INL ERROR (ppm) 80 CIN = 0.1µF 40 CIN = 1µF CIN = 10µF 0 CIN = 0.01µF 0 200 600 800 400 RESISTANCE AT VREF (Ω) 1000 24012 F22 Figure 22. Full-Scale Error vs RVREF (Large C) 50 FULL-SCALE ERROR (ppm) 25 VCC = 5V VREF = 5V VIN = 5V TA = 25°C CIN = 10µF 0 CIN = 1000pF –25 CIN = 20pF CIN = 100pF INL ERROR (ppm) –50 100 1k 10k RESISTANCE AT VREF (Ω) 100k 24012 F23 Figure 23. Full-Scale Error vs RVFEF (Small C) U at node VREF is small (CVREF < 0.01µF), the reference input can tolerate large external resistances without reduction in INL, see Figure 24. If the external capacitance is large (CVREF > 0.01µF), the linearity will be degraded by 0.04ppm/Ω independent of capacitance at VREF, see Figure 25. In addition to the dynamic reference current, the VREF ESD protection diodes have a temperature dependent leakage current. This leakage current, nominally 1nA (±10nA max), results in a fixed full-scale shift of 10µV for a 10k source resistance. 50 40 VCC = 5V VREF = 5V TA = 25°C CIN = 1000pF 30 CIN = 0.01µF 20 CIN = 100pF CIN = 20pF 10 0 100 1k 10k RESISTANCE AT VREF (Ω) 100k 24012 F24 W UU Figure 24. INL Error vs RVREF (Small C) 40 VCC = 5V VREF = 5V TA = 25°C CVREF = 10µF CVREF = 1µF CVREF = 0.1µF 30 20 10 CVREF = 0.01µF 0 0 200 600 800 400 RESISTANCE AT VREF (Ω) 1000 24012 F25 Figure 25. INL Error vs RVREF (Large C) 25 LTC2401/LTC2402 APPLICATIO S I FOR ATIO ANTIALIASING One of the advantages delta-sigma ADCs offer over conventional ADCs is on-chip digital filtering. Combined with a large oversampling ratio, the LTC2401/LTC2402 significantly simplify antialiasing filter requirements. The digital filter provides very high rejection except at integer multiples of the modulator sampling frequency (fS), see Figure 26. The modulator sampling frequency is 256 • FO, where FO is the notch frequency (typically 50Hz or 60Hz). The bandwidth of signals not rejected by the digital filter is narrow (≈ 0.2%) compared to the bandwidth of the frequencies rejected. As a result of the oversampling ratio (256) and the digital filter, minimal (if any) antialias filtering is required in front of the LTC2401/LTC2402. If passive RC components are placed in front of the LTC2401/LTC2402, the input dynamic current should be considered (see Input Current section). In cases where large effective RC time constants are used, an external buffer amplifier may be required to minimize the effects of input dynamic current. The modulator contained within the LTC2401/LTC2402 can handle large-signal level perturbations without saturating. Signal levels up to 40% of VREF do not saturate the analog modulator. These signals are limited by the input ESD protection to 300mV below ground and 300mV above VCC. 0 –20 –40 REJECTION (dB) –60 –80 –100 –120 –140 0 fS/2 INPUT FREQUENCY 24012 F26 fS Figure 26. Sinc4 Filter Rejection 26 U Single Ended Half-Bridge Digitizer with Reference and Ground Sensing Sensors convert real world phenomena (temperature, pressure, gas levels, etc.) into a voltage. Typically, this voltage is generated by passing an excitation current through the sensor. The wires connecting the sensor to the ADC form parasitic resistors RP1 and RP2. The excitation current also flows through parasitic resistors RP1 and RP2, as shown in Figure 27. The voltage drop across these parasitic resistors leads to systematic offset and full-scale errors. In order to eliminate the errors associated with these parasitic resistors, the LTC2401/LTC2402 include a fullscale set input (FSSET) and a zero-scale set input (ZSSET). As shown in Figure 28, the FSSET pin acts as a zero current full-scale sense input. Errors due to parasitic resistance RP1 in series with the half-bridge sensor are removed by the FSSET input to the ADC. The absolute fullscale output of the ADC (data out = FFFFFFHEX ) will occur RP1 W UU + V – FULL-SCALE ERROR + SENSOR OUTPUT – IEXCITATION SENSOR RP2 + V – OFFSET ERROR 24012 F27 Figure 27. Errors Due to Excitation Currents 1 RP1 VB RP3 IDC = 0 IEXCITATION RP4 IDC = 0 VA RP2 RP5 VCC IDC = 0 2 LTC2401 FSSET SCK VIN SDO CS 5 6 ZSSET GND FO 10 24012 F03 9 8 7 3-WIRE SPI INTERFACE 3 Figure 28. Half-Bridge Digitizer with Zero-Scale and Full-Scale Sense LTC2401/LTC2402 APPLICATIO S I FOR ATIO at VIN = VB = FSSET, see Figure 29. Similarly, the offset errors due to RP2 are removed by the ground sense input ZSSET. The absolute zero output of the ADC (data out = 000000HEX) occurs at VIN = VA = ZSSET. Parasitic resistors RP3 to RP5 have negligible errors due to the 1nA (typ) leakage current at pins FSSET, ZSSET and VIN. The wide dynamic input range (– 300mV to 5.3V) and low noise (0.6ppm RMS) enable the LTC2401 or the LTC2402 to directly digitize the output of the bridge sensor. The LTC2402 is ideal for applications requiring continuous monitoring of two input sensors. As shown in Figure 30, the LTC2402 can monitor both a thermocouple FFFFFH ADC DATA OUT 00000H ZSSET VIN Figure 29. Transfer Curve with Zero-Scale and Full-Scale Set 2.7V TO 5.5V LTC2402 1 12k COLD JUNCTION THERMISTOR 100Ω 2 3 4 5 VCC FSSET CH1 CH0 ZSSET FO SCK SDO CS GND 10 9 8 7 6 PROCESSOR + THERMOCOUPLE Figure 30. Isolated Temperature Measurement U temperature probe and a cold junction temperature sensor. Absolute temperature measurements can be performed with a variety of thermocouples using digital cold junction compensation. The selection between CH0 and CH1 is automatic. Initially, after power-up, a conversion is performed on CH0. For each subsequent conversion, the input channel selection is alternated. Embedded within the serial data output is a status bit indicating which channel corresponds to the conversion result. If the conversion was performed on CH0, this bit (Bit 30) is LOW and is HIGH if the conversion was performed on CH1 (see Figure 31). 12.5% EXTENDED RANGE 12.5% UNDER RANGE FSSET 24012 F29 24012 F30 W UU – ISOLATION BARRIER 27 LTC2401/LTC2402 APPLICATIO S I FOR ATIO SCK ••• SDO EOC CH1 CH1 DATA OUT EOC CH0 Figure 31. Embedded Selected Channel Indicator 350Ω 350Ω Figure 32. Pseudo Differential Strain Guage Application There are no extra control or status pins required to perform the alternating 2-channel measurements. The LTC2402 only requires two digital signals (SCK and SDO). This simplification is ideal for isolated temperature measurements or systems where minimal control signals are available. Pseudo Differential Applications Generally, designers choose fully differential topologies for several reasons. First, the interface to a 4- or 6-wire bridge is simple (it is a differential output). Second, they require good rejection of line frequency noise. Third, they typically look at a small differential signal sitting on a large common mode voltage; they need accurate measurements of the differential signal independent of 28 U ••• CH0 DATA OUT 24012 F31 W UU IEXCITATION IDC = 0 2 5V 1 VCC 350Ω 3 4 350Ω IDC = 0 5 FSSET LTC2402 9 SCK CH1 CH0 SDO CS FO ZSSET GND 24012 F32 8 7 10 3-WIRE SPI INTERFACE the common mode input voltage. Many applications currently using fully differential analog-to-digital converters for any of the above reasons may migrate to a pseudo differential conversion using the LTC2402. Direct Connection to a Full Bridge The LTC2402 interfaces directly to a 4- or 6-wire bridge, as shown in Figure 32. The LTC2402 includes a FSSET and a ZSSET for sensing the excitation voltage directly across the bridge. This eliminates errors due to excitation currents flowing through parasitic resistors. The LTC2402 also includes two single ended input channels which can tie directly to the differential output of the bridge. The two conversion results may be digitally subtracted yielding the differential result. LTC2401/LTC2402 APPLICATIO S I FOR ATIO The LTC2402’s single ended rejection of line frequencies (± 2%) and harmonics is better than 110dB. Since the device performs two independent single ended conversions each with > 110dB rejection, the overall common mode and differential rejection is much better than the 80dB rejection typically found in other differential input delta-sigma converters. In addition to excellent rejection of line frequency noise, the LTC2402 also exhibits excellent single ended noise rejection over a wide range of frequencies due to its 4th order sinc filter. Each single ended conversion independently rejects high frequency noise (> 60Hz). Care must be taken to insure noise at frequencies below 15Hz and at multiples of the ADC sample rate (15,360Hz) are not present. For this application, it is recommended the LTC2402 is placed in close proximity to the bridge sensor in order to reduce the noise injected into the ADC input. By performing three successive conversions (CH0-CH1-CH0), the drift and low frequency noise can be measured and compensated for digitally. The absolute accuracy (less than 10 ppm total error) of the LTC2402 enables extremely accurate measurement of small signals sitting on large voltages. Each of the two pseudo differential measurements performed by the LTC2402 is absolutely accurate independent of the common mode voltage output from the bridge. The pseudo differential result obtained from digitally subtracting the two single ended conversion results is accurate to within IEXCITATION = 200µA + Pt VRTD 100Ω – IEXCITATION = 200µA R1 IDC = 0 R2 Figure 33. RTD Remote Temperature Measurement U the noise level of the device (3µVRMS) times the square root of 2, independent of the common mode input voltage. Typically, a bridge sensor outputs 2mV/V full scale. With a 5V excitation, this translates to a full-scale output of 10mV. Divided by the RMS noise of 4.2µV(= 3µV • 1.414), this circuit yields 2,300 counts with no averaging or amplification. If more counts are required, several conversions may be averaged (the number of effective counts is increased by a factor of square root of 2 for each doubling of averages). An RTD Temperature Digitizer RTDs used in remote temperature measurements often have long lead lengths between the ADC and RTD sensor. These long lead lengths lead to voltage drops due to excitation current in the interconnect to the RTD. This voltage drop can be measured and digitally removed using the LTC2402 (see Figure 33). The excitation current (typically 200µA) flows from the ADC through a long lead length to the remote temperature sensor (RTD). This current is applied to the RTD, whose resistance changes as a function of temperature (100Ω to 400Ω for 0°C to 800°C). The same excitation current flows back to the ADC ground and generates another voltage drop across the return leads. In order to get an accurate measurement of the temperature, these voltage drops must be measured and removed from the conversion result. Assuming the resistance is approximately the same 5V 1 2 VCC FSSET LTC2402 25Ω 5k 4 SCK CH0 SDO CS CH1 FO ZSSET GND 24012 F33 W UU 9 8 7 10 3-WIRE SPI INTERFACE 1000pF 3 25Ω 5k 0.1µF 5 29 LTC2401/LTC2402 APPLICATIO S I FOR ATIO for the forward and return paths (R1 = R2), the auxiliary channel on the LTC2402 can measure this drop. These errors are then removed with simple digital correction. The result of the first conversion on CH0 corresponds to an input voltage of VRTD + R1 • IEXCITATION. The result of the second conversion (CH1) is – R1 • IEXCITATION. Note, the LTC2402’s input range is not limited to the supply rails, it has underrange capabilities. The device’s input range is – 300mV to VREF + 300mV. Adding the two conversion results together, the voltage drop across the RTD’s leads are cancelled and the final result is VRTD. An Isolated, 24-Bit Data Acquisition System The LTC1535 is useful for signal isolation. Figure 34 shows a fully isolated, 24-bit differential input A/D converter implemented with the LTC1535 and LTC2402. Power on the isolated side is regulated by an LT1761-5.0 low noise, low dropout micropower regulator. Its output is suitable for driving bridge circuits and for ratiometric applications. 1/2 BAT54C T1 1/2 BAT54C “SDO” “SCK” LOGIC 5V RO ST1 RE DE DI VCC1 10µF 10V TANT ST2 LTC1535 G1 G2 + 1 1 1 2 ISOLATION BARRIER Figure 34. Complete, Isolated 24-Bit Data Acquisition System 30 U During power-up, the LTC2402 becomes active at VCC = 2.3V, while the isolated side of the LTC1535 must wait for VCC2 to reach its undervoltage lockout threshold of 4.2V. Below 4.2V, the LTC1535’s driver outputs Y and Z are in a high impedance state, allowing the 1kΩ pull-down to define the logic state at SCK. When the LTC2402 first becomes active, it samples SCK; a logic “0” provided by the 1kΩ pull-down invokes the external serial clock mode. In this mode, the LTC2402 is controlled by a single clock line from the nonisolated side of the barrier, through the LTC1535’s driver output Y. The entire power-up sequence, from the time power is applied to VCC1 until the LT1761’s output has reached 5V, is approximately 1ms. Data returns to the nonisolated side through the LTC1535’s receiver at RO. An internal divider on receiver input B sets a logic threshold of approximately 3.4V at input A, facilitating communications with the LTC2402’s SDO output without the need for any external components. LT1761-5 W UU + 10µF 16V TANT 1µF IN SHDN OUT 10µF BYP GND + 10µF 10V TANT 2 + 2 VCC2 A B Y Z 10µF 10V TANT LTC2402 FO SCK SDO CS GND VCC FSSET CH1 CH0 ZSSET 10µF CERAMIC 2 1k 1 2 = LOGIC COMMON = FLOATING COMMON 2 2 24012 F09 T1 = COILTRONICS CTX02-14659 OR SIEMENS B78304-A1477-A3 LTC2401/LTC2402 PACKAGE I FOR ATIO 0.007 (0.18) 0.021 ± 0.006 (0.53 ± 0.015) * DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE ** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U W U Dimensions in inches (millimeters) unless otherwise noted. MS10 Package 10-Lead Plastic MSOP (LTC DWG # 05-08-1661) 0.118 ± 0.004* (3.00 ± 0.102) 10 9 8 7 6 0.193 ± 0.006 (4.90 ± 0.15) 0.118 ± 0.004** (3.00 ± 0.102) 12345 0.040 ± 0.006 (1.02 ± 0.15) 0° – 6° TYP SEATING PLANE 0.009 (0.228) REF 0.034 ± 0.004 (0.86 ± 0.102) 0.0197 (0.50) BSC 0.006 ± 0.004 (0.15 ± 0.102) MSOP (MS10) 1098 31 LTC2401/LTC2402 TYPICAL APPLICATIO Figure 35 shows the block diagram of a demo circuit (contact LTC for a demonstration) of a multichannel isolated temperature measurement system. This circuit decodes an address to select which LTC2402 receives a 32-bit burst of SCK signal. All devices independently D1 SCK SD0 DIN (ADDRESS OR COUNTER) Figure 35. Mulitchannel Isolated Temperature Measurement System RELATED PARTS PART NUMBER LT1019 LTC1050 LT1236A-5 LTC1391 LT1460 LT1461-2.5 LTC1535 LTC2400 LTC2404/LTC2408 LTC2410 LTC2411 LTC2413 LTC2420 LTC2424/LTC2428 DESCRIPTION Precision Bandgap Reference, 2.5V, 5V Precision Chopper Stabilized Op Amp Precision Bandgap Reference, 5V 8-Channel Multiplexer Micropower Series Reference Precision Micropower Voltage Reference Isolated RS485 Transceiver 24-Bit, No Latency ∆Σ ADC in SO-8 4-/8-Channel, 24-Bit, No Latency ∆Σ ADC 24-Bit, Fully Differential, No Latency ∆Σ ADC in SSOP-16 24-Bit, Fully Differential, No Latency ∆Σ ADC in MS10 24-Bit, No Latency ∆Σ ADC 20-Bit, No Latency ∆Σ ADC in SO-8 4-/8-Channel, 20-Bit, No Latency ∆Σ ADC COMMENTS 3ppm/°C Drift, 0.05% Max No External Components 5µV Offset, 1.6µVP-P Noise 0.05% Max, 5ppm/°C Drift Low RON: 45Ω, Low Charge Injection Serial Interface 0.075% Max, 10ppm/°C Max Drift, 2.5V, 5V and 10V Versions 50µA Supply Current, 3ppm/°C Drift 2500VRMS Isolation 4ppm INL, 10ppm Total Unadjusted Error, 200µA 4ppm INL, 10ppm Total Unadjusted Error, 200µA 0.16ppm Noise, 2ppm INL, 10ppm Total Unadjusted Error, 200µA 0.29ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200µA Simultaneous 50Hz and 60Hz Rejection, 0.16ppm Noise 1.2ppm Noise, 8ppm INL, Pin Compatible with LTC2400 1.2ppm Noise, 8ppm INL, Pin Compatible with LTC2404/LTC2408 24012f LT/LCG 1000 4K • PRINTED IN USA 32 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408)432-1900 q FAX: (408) 434-0507 q www.linear-tech.com U convert either the thermal couple output or the thermistor cold juntion output. After each conversion, the devices enter their sleep state and wait for the SCK signal before clocking out data and beginning the next conversion. LTC1535 A RE Y R0 SDO SCK ZSSET VCC FSSET CH1 CH0 LTC2402 HC138 D1 LTC1535 A RE Y R0 SDO SCK ZSSET VCC FSSET CH1 CH0 LTC2402 + – 2500V D1 HC138 RE Y R0 SEE FIGURE 34 FOR THE COMPLETE CIRCUIT LTC1535 A SDO SCK VCC FSSET CH1 CH0 LTC2402 ZSSET HC595 ADDRESS LATCH 24012 F35 © LINEAR TECHNOLOGY CORPORATION 2000