LTC3109

LTC3105 400mA Step-Up DC/DC Converter with Maximum Power Point Control and 250mV Start-Up FEATURES n n n n n n n n n n n n DESCRIPTION The LTC®3105 is a high efficiency step-up DC/DC converter that can operate from input voltages as low as 225mV. A 250mV start-up capability and integrated maximum power point controller (MPPC) enable operation directly from low voltage, high impedance alternative power sources such as photovoltaic cells, TEGs (thermoelectric generators) and fuel cells. A user programmable MPPC set point maximizes the energy that can be extracted from any power source. Burst Mode operation, with a proprietary self adjusting peak current, optimizes converter efficiency and output voltage ripple over all operating conditions. The AUX powered 6mA LDO provides a regulated rail for external microcontrollers and sensors while the main output is charging. In shutdown, IQ is reduced to 10µA and integrated thermal shutdown offers protection from overtemperature faults. The LTC3105 is offered in 10-lead 3mm × 3mm × 0.75mm DFN and 12-lead MSOP packages. L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Low Start-Up Voltage: 250mV Maximum Power Point Control Wide VIN Range: 225mV to 5V Auxiliary 6mA LDO Regulator Burst Mode® Operation: IQ = 24µA Output Disconnect and Inrush Current Limiting VIN > VOUT Operation Antiringing Control Soft Start Automatic Power Adjust Power Good Indicator 10-Lead 3mm × 3mm × 0.75mm DFN and 12-Lead MSOP Packages APPLICATIONS n n n n n Solar Powered Battery/Supercapacitor Chargers Energy Har vesting Remote Industrial Sensors Low Power Wireless Transmitters Cell Phone, MP3, PMP and GPS Accessory Chargers TYPICAL APPLICATION Single Photovoltaic Cell Li-Ion Trickle Charger 10µH 225mV TO 5V PHOTOVOLTAIC CELL 80 70 VOUT 4.1V 1020k FB MPPC OFF ON 40.2k 1µF SHDN AUX GND PGOOD LDO FBLDO 4.7µF 3105 TA01a Output Current vs Input Voltage MPPC DISABLED VOUT = 3.3V – 10µF LTC3105 VOUT OUTPUT CURRENT (mA) + VIN SW 60 50 40 30 20 10 0 0.2 0.3 VOUT = 4.2V Li-Ion 332k 2.2V 10µF VOUT = 5V 0.4 0.5 0.6 0.7 0.8 INPUT VOLTAGE (V) 0.9 1.0 3105 TA01b 3105fa 1 LTC3105 ABSOLUTE MAXIMUM RATINGS (Note 1) SW Voltage DC............................................................ –0.3V to 6V Pulsed ( VLDO VFBLDO = 0V External Feedback Network ILDO = 1mA to 6mA VAUX = 2.5V to 5V ILDO = 6mA, VOUT = VAUX = 2.2V VLDO 0.5V Below Regulation Voltage VIN = VAUX = VOUT = 0V, VSHDN = 0V l l l l l The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VAUX = VOUT = 3.3V, VLDO = 2.2V, VIN = 0.6V, unless otherwise noted. CONDITIONS MIN 0.225 0.25 1.5 0.984 1.004 24 10 9.72 l l TYP MAX 5 0.4 0.36 5.25 1.024 UNITS V V V V V µA µA (Note 5) TJ = 0°C to 85°C (Note 5) l l l VFB = 1.10V SHDN = 0V VMPPC = 0.6V 1.1 10 10.28 0.3 µA V V µA µA Ω Ω A A VIN = VSW = 5V, VSHDN = 0V VIN = VSW = 0V, VOUT = VAUX = 5.25V 1 1 0.5 0.5 10 10 VFB = 0.90V, VMPPC = 0.4V (Note 3) VFB = 0.90V, VMPPC = 0.4V (Note 3) VOUT Falling 0.4 0.275 85 1.4 2.148 0.984 0.5 0.35 90 95 5 2.2 1.004 0.40 0.15 105 2.236 1.024 % V V V % % mV mA µA 6 12 1 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3105 is tested under pulsed load conditions such that TJ ≈ TA. The LTC3105E is guaranteed to meet specifications from 0°C to 85°C junction temperature. Specifications over the –40°C to 85°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. Note 3: Current measurements are performed when the LTC3105 is not switching. The current limit values measured in operation will be somewhat higher due to the propagation delay of the comparators. Note 4: This IC includes over temperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 5: The LTC3105 has been optimized for use with high impedance power sources such as photovoltaic cells and thermoelectric generators. The input start-up voltage is measured using an input voltage source with a series resistance of approximately 200mΩ and MPPC enabled. Use of the LTC3105 with lower resistance voltage sources or with MPPC disabled may result in a higher input start-up voltage. 3105fa 3 LTC3105 TYPICAL PERFORMANCE CHARACTERISTICS VIN = 0.6V, unless otherwise noted. Minimum Input Start-Up Voltage vs Temperature 340 320 THRESHOLD VOLTAGE (mV) INPUT VOLTAGE (mV) 300 280 260 240 220 200 –45 –30 –15 1000 900 800 700 600 500 400 300 200 100 0 15 30 45 60 TEMPERATURE (°C) 75 90 3105 G01 TA = 25°C, VAUX = VOUT = 3.3V, VLDO = 2.2V, Shutdown Thresholds vs Input Voltage IC ENABLE 120 IC Enable Delay vs Input Voltage 100 IC DISABLE DELAY TIME (µs) 80 60 0 1.25 2.25 4.25 3.25 SUPPLY VOLTAGE, VIN OR VAUX (V) 5.25 3105 G02 40 1.25 2.25 4.25 3.25 SUPPLY VOLTAGE, VIN OR VAUX (V) 5.25 3105 G03 MPPC Current Variation vs Temperature 2.5 2.0 CHANGE FROM 25°C (%) SOFT-START TIME (ms) 0 15 30 45 60 TEMPERATURE (°C) 75 90 3105 G05 LDO Soft-Start Duration vs LDO Load 1.25 1.20 1.15 1.10 1.05 1.00 0.95 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –45 –30 –15 1 3 4 5 2 LDO LOAD CURRENT (mA) 6 3105 G06 VOUT IQ vs Temperature During Shutdown 22 20 18 16 IQ (µA) 14 12 10 8 6 4 –45 –30 –15 0 15 30 45 60 TEMPERATURE (°C) 75 90 3105 G07 VIN for Synchronous Operation 5.0 4.5 MAXIMUM INPUT VOLTAGE (V) 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 OUTPUT VOLTAGE (V) 5.0 5.5 3105 G09 SHDN = 0V NONSYNCHRONOUS OPERATION SYNCHRONOUS OPERATION 3105fa 4 LTC3105 TYPICAL PERFORMANCE CHARACTERISTICS VIN = 0.6V, unless otherwise noted. Exiting MPPC Control on Input Voltage Step VIN VOLTAGE 200mV/DIV VMPPC = 400mV 1.0 0.5 CHANGE FROM 25°C (%) 0 –0.5 –1.0 –1.5 –2.0 15µs/DIV –2.5 –45 –30 –15 IVALLEY EFFICIENCY (%) IPEAK 90 80 70 60 50 40 0.25 TA = 25°C, VAUX = VOUT = 3.3V, VLDO = 2.2V, IPEAK and IVALLEY Current Limit Change vs Temperature 100 Efficiency vs VIN VOUT = 3V ILOAD = 10mA LDO = 2.2V INDUCTOR CURRENT 100mA/DIV MPPC VOLTAGE 200mV/DIV 3105 G10 0 15 30 45 60 TEMPERATURE (°C) 75 90 3105 G11 1.25 2.25 3.25 4.25 INPUT VOLTAGE (V) 5.25 3105 G12 Input and Output Burst Ripple VIN = 0.6V CIN = 470µF OUTPUT VOLTAGE 50mV/DIV SW CURRENT 200mA/DIV VOUT = 3.3V IOUT = 15mA COUT = 10µF EFFICIENCY (%) 90 80 70 60 50 40 30 20 10 50µs/DIV Efficiency vs Output Current and Power Loss, VOUT = 3.3V VIN = 0.6V VIN = 0.8V VIN = 1V EFFICIENCY 1000 100 POWER LOSS (mW) 10 POWER LOSS 1 INPUT VOLTAGE 5mV/DIV 3105 G13 0 0.01 0.1 1 10 0.1 100 3105 G14 OUTPUT CURRENT (mA) Efficiency vs Output Current and Power Loss, VOUT = 5V 100 90 80 EFFICIENCY (%) 70 60 50 40 30 20 0.01 1 10 0.1 OUTPUT CURRENT (mA) 0.1 100 3105 G15 No-Load Input Current vs Input Voltage 1000 800 700 INPUT CURRENT (µA) 100 600 500 400 300 200 100 0 0.2 0.4 0.6 0.8 INPUT VOLTAGE (V) 1.0 1.2 3105 G16 VIN = 3V VIN = 2V VIN = 1.5V EFFICIENCY VOUT = 3.3V POWER LOSS (mW) 10 POWER LOSS 1 3105fa 5 LTC3105 PIN FUNCTIONS (DFN/MSOP) FB (Pin 1/Pin 1): Step-Up Converter Feedback Input. Connect the VOUT resistor divider tap to this input. The output voltage can be adjusted between 1.5V and 5.25V. LDO (Pin 2/Pin 2): LDO Regulator Output. Connect a 4.7µF or larger capacitor between LDO and GND. FBLDO (Pin 3/Pin 3): LDO Feedback Input. Connect the LDO resistive divider tab to this input. Alternatively, connecting FBLDO directly to GND will configure the LDO output voltage to be internally set at 2.2V (nominal). SHDN (Pin 4/Pin 4): Logic Controlled Shutdown Input. With SHDN open, the converter is enabled by an internal 2MΩ pull-up resistor. The SHDN pin should be driven with an open-drain or open-collector pull-down and floated until the converter has entered normal operation. Excessive loading on this pin may cause a failure to complete start-up. SHDN = Low: IC Disabled SHDN = High: IC Enabled MPPC (Pin 5/Pin 5): Set Point Input for Maximum Power Point Control. Connect a resistor from MPPC to GND to program the activation point for the MPPC loop. To disable the MPPC circuit, connect MPPC directly to GND. VIN (Pin 6/Pin 8): Input Supply. Connect a decoupling capacitor between this pin and GND. The PCB trace length from the VIN pin to the decoupling capacitor should be as short and wide as possible. When used with high impedance sources such as photovoltaic cells, this pin should have a 10µF or larger decoupling capacitor. GND (Exposed Pad Pin 11/Pins 6, 7) : Small Signal and Power Ground for the IC. The GND connections should be soldered to the PCB ground using the lowest impedance path possible. SW (Pin 7/Pin 9): Switch Pin. Connect an inductor between SW and VIN. PCB trace lengths should be as short as possible to reduce EMI. While the converter is sleeping or is in shutdown, the internal antiringing switch connects the SW pin to the VIN pin in order to minimize EMI. PGOOD (Pin 8/Pin 10): Power Good Indicator. This is an open-drain output. The pull-down is disabled when VOUT has achieved the voltage defined by the feedback divider on the FB pin. The pull-down is also disabled while the IC is in shutdown or start-up mode. VOUT (Pin 9/Pin 11): Step-Up Converter Output. This is the drain connection of the main output internal synchronous rectifier. A 10µF or larger capacitor must be connected between this pin and GND. The PCB trace length from the VOUT pin to the output filter capacitor should be as short and wide as possible. AUX (Pin 10/Pin 12): Auxiliary Voltage. Connect a 1µF capacitor between this pin and GND. This pin is used by the start-up circuitry to generate a voltage rail to power internal circuitry until the main output reaches regulation. AUX and VOUT are internally connected together once VOUT exceeds VAUX. 3105fa 6 LTC3105 BLOCK DIAGRAM L1 10µH 7 SHUTDOWN SLEEP OR SW WELL CONTROL AUX SHORT CONTROL LOW VOLTAGE START-UP CURRENT ADJUST VAUX 10 CAUX 1µF 1.5V TO 5.25V COUT 10µF (Pin Numbers for DFN Package Only) 225mV TO 5V 6 CIN 10µF VIN VOUT 9 SHUTDOWN VCC MPPC 10µA VIN VCC SHDN 2M LDO 2 CLDO 4.7µF –+ –+ PEAK CURRENT LIMIT VALLEY CURRENT LIMIT LOGIC USER SHUTDOWN 5 RMPPC – gm + SHUTDOWN SLEEP BURST CONTROL 4 1.004V VIN VAUX VCC EXPOSED PAD 11 FB 0.9V + – – + 1.004V –+ FBLDO FB PGOOD 3 1 8 SLEEP 3105 BD R3 R1 R4 R2 3105fa 7 LTC3105 OPERATION Introduction The LTC3105 is a unique, high performance, synchronous boost converter that incorporates maximum power point control, 250mV start-up capability and an integrated LDO regulator. This part operates over a very wide range of input voltages from 225mV to 5V. Its Burst Mode architecture and low 24µA quiescent current optimize efficiency in low power applications. An integrated maximum power point controller allows for operation directly from high impedance sources such as photovoltaic cells by preventing the input power source voltage from collapsing below the user programmable MPPC threshold. Peak current limits are automatically adjusted with proprietary techniques to maintain operation at levels that maximize power extraction from the source. The 250mV start-up voltage and 225mV minimum operating voltage enable direct operation from a single photovoltaic cell and other very low voltage, high series impedance power sources such as TEGs and fuel cells. Synchronous rectification provides high efficiency operation while eliminating the need for external Schottky diodes. The LTC3105 provides output disconnect which prevents large inrush currents during start-up. This is particularly important for high internal resistance power sources like photovoltaic cells and thermoelectric generators which can become overloaded if inrush current is not limited during start-up of the power converter. In addition, output disconnect isolates VOUT from VIN while in shutdown. VIN > VOUT Operation The LTC3105 includes the ability to seamlessly maintain regulation if VIN becomes equal to or greater than VOUT . With VIN greater than or equal to VOUT , the synchronous rectifiers are disabled which may result in reduced efficiency. Shutdown Control The SHDN pin is an active low input that places the IC into low current shutdown mode. This pin incorporates an internal 2MΩ pull-up resistor which enables the converter if the SHDN pin is not controlled by an external circuit. The SHDN pin should be allowed to float while the part is in start-up mode. Once in normal operation, the SHDN pin may be controlled using an open-drain or open-collector pull-down. Other external loads on this pin should be avoided, as they may result in the part failing to reach regulation. In shutdown, the internal switch connecting AUX and VOUT is enabled. When the SHDN pin is released, the LTC3105 is enabled and begins switching after a short delay. When either VIN or VAUX is above 1.4V, this delay will typically range between 20µs and 100µs. Refer to the Typical Performance Characteristics section for more details. Start-Up Mode Operation The LTC3105 provides the capability to start with voltages as low as 250mV. During start-up the AUX output initially is charged with the synchronous rectifiers disabled. Once VAUX has reached approximately 1.4V, the converter leaves start-up mode and enters normal operation. Maximum power point control is not enabled during start-up, however, the currents are internally limited to sufficiently low levels to allow start-up from weak input sources. While the converter is in start-up mode, the internal switch between AUX and VOUT remains disabled and the LDO is disabled. Refer to Figure 1 for an example of a typical start-up sequence. The LTC3105 is optimized for use with high impedance power sources such as photovoltaic cells. For operation from very low impedance, low input voltage sources, it may be necessary to add several hundred milliohms of series input resistance to allow for proper low voltage start-up. Normal Operation When either VIN or VAUX is greater than 1.4V typical, the converter will enter normal operation. The converter continues charging the AUX output until the LDO output enters regulation. Once the LDO output is in regulation, the converter begins charging the VOUT pin. VAUX is maintained at a level sufficient to ensure the LDO remains in regulation. If VAUX becomes higher than required to maintain LDO regulation, charge is transferred from the AUX output to the VOUT output. If VAUX falls too low, current is redirected to the AUX output instead of being used to charge the VOUT output. Once VOUT rises 3105fa 8 LTC3105 OPERATION INDUCTOR CURRENT TIME OUTPUT VOLTAGE VAUX VLDO VOUT 1.4V LDO IN REGULATION START-UP MODE NORMAL OPERATION VOUT SYNCHRONOUS RECTIFIER ENABLED VOUT IN REGULATION VOUT = VAUX TIME 3105 F01 Figure 1. Typical Converter Start-Up Sequence above VAUX , an internal switch is enabled to connect the two outputs together. If VIN is greater than the voltage on the driven output (VOUT or VAUX), or the driven output is less than 1.2V (typical), the synchronous rectifiers are disabled. With the synchronous rectifiers disabled, the converter operates in critical conduction mode. In this mode, the N-channel MOSFET between SW and GND is enabled and remains on until the inductor current reaches the peak current limit. It is then disabled and the inductor current discharges completely before the cycle is repeated. When the output voltage is greater than the input voltage and greater than 1.2V, the synchronous rectifier is enabled. In this mode, the N-channel MOSFET between SW and GND is enabled until the inductor current reaches the peak current limit. Once current limit is reached, the N-channel MOSFET turns off and the P-channel MOSFET between SW and the driven output is enabled. This switch remains on until the inductor current drops below the valley current limit and the cycle is repeated. When VOUT reaches the regulation point, the N- and Pchannel MOSFETs connected to the SW pin are disabled and the converter enters sleep. Auxiliary LDO The integrated LDO provides a regulated 6mA rail to power microcontrollers and external sensors. When the input voltage is above the minimum of 225mV, the LDO is powered from the AUX output allowing the LDO to attain regulation while the main output is still charging. The LDO has a 12mA current limit and an internal 1ms soft-start to eliminate inrush currents. The LDO output voltage is set by the FBLDO pin. If a resistor divider is connected to this pin, the ratio of the resistors determines the LDO output voltage. If the FBLDO pin is connected directly to GND, the LDO will use a 2MΩ internal divider network to program a 2.2V nominal output voltage. The LDO should be programmed for an output voltage less than the programmed VOUT . 3105fa 9 LTC3105 OPERATION When the converter is placed in shutdown mode, the LDO is forced into reverse-blocking mode with reverse current limited to under 1µA. After the shutdown event has ended, the LDO remains in reverse-blocking mode until VAUX has risen above the LDO voltage. MPPC Operation The maximum power point control circuit allows the user to set the optimal input voltage operating point for a given power source. The MPPC circuit dynamically regulates the average inductor current to prevent the input voltage from dropping below the MPPC threshold. When VIN is greater than the MPPC voltage, the inductor current is increased until VIN is pulled down to the MPPC set point. If VIN is less than the MPPC voltage, the inductor current is reduced until VIN rises to the MPPC set point. Automatic Power Adjust The LTC3105 incorporates a feature that maximizes efficiency at light load while providing increased power capability at heavy load by adjusting the peak and valley of the inductor current as a function of load. Lowering the peak inductor current to 100mA at light load optimizes efficiency by reducing conduction losses. As the load increases, the peak inductor current is automatically increased to a maximum of 500mA. At intermediate loads, the peak inductor current can vary between 100mA to 500mA. This function is overridden by the MPPC function and will only be observed when the power source can deliver more power than the load requires. PGOOD Operation The power good output is used to indicate that VOUT is in regulation. PGOOD is an open-drain output, and is disabled in shutdown. PGOOD will indicate that power is good at the beginning of the first sleep event after the output voltage has risen above 90% of its regulation value. PGOOD remains asserted until VOUT drops below 90% of its regulation value at which point PGOOD will pull low. APPLICATIONS INFORMATION Component Selection Low DCR power inductors with values between 4.7µH and 30µH are suitable for use with the LTC3105. For most applications, a 10µH inductor is recommended. In applications where the input voltage is very low, a larger value inductor can provide higher efficiency and a lower start-up voltage. In applications where the input voltage is relatively high (VIN > 0.8V), smaller inductors may be used to provide a smaller overall footprint. In all cases, the inductor must have low DCR and sufficient saturation current rating. If the DC resistance of the inductor is too high, efficiency will be reduced and the minimum operating voltage will increase. Input capacitor selection is highly important in low voltage, high source resistance systems. For general applications, a 10µF ceramic capacitor is recommended between VIN and GND. For high impedance sources, the input capacitor should be large enough to allow the converter to complete start-up mode using the energy stored in the input capacitor. When using bulk input capacitors that have high ESR, a small valued parallel ceramic capacitor should be placed between VIN and GND as close to the converter pins as possible. A 1µF ceramic capacitor should be connected between AUX and GND. Larger capacitors should be avoided to minimize start-up time. A low ESR output capacitor should be connected between VOUT and GND. The main output capacitor should be 10µF or larger. The main output can also be used to charge energy storage devices including tantalum capacitors, supercapacitors and batteries. When using output bulk storage devices with high ESR, a small valued ceramic capacitor should be placed in parallel and located as close to the converter pins as possible. 3105fa 10 LTC3105 APPLICATIONS INFORMATION Step-Up Converter Feedback Configuration A resistor divider connected between the VOUT and FB pins programs the step-up converter output voltage, as shown in Figure 2. An optional 22pF feedforward capacitor, CFF1, can be used to reduce output ripple and improve load transient response. The equation for VOUT is:  R1  VOUT = 1.004V •  +1  R2   LDO Regulator Feedback Configuration Two methods can be used to program the LDO output voltage, as shown in Figure 3. A resistor divider connected between the LDO and FBLDO pins can be used to program the LDO output voltage. The equation for the LDO output voltage is:  R3  VLDO = 1.004V •  +1  R4   Alternatively, the FBLDO pin can be connected directly to GND. In this configuration, the LDO is internally set to a nominal 2.2V output. VOUT CFF1 R1 FB R2 LTC3105 10µA RMPPC MPPC Threshold Configuration The MPPC circuit controls the inductor current to maintain VIN at the voltage on the MPPC pin. The MPPC pin voltage is set by connecting a resistor between the MPPC pin and GND, as shown in Figure 4. The MPPC voltage is determined by the equation: VMPPC = 10µA • RMPPC In photovoltaic cell applications, a diode can be used to set the MPPC threshold so that it tracks the cell voltage over temperature, as shown in Figure 5. The diode should be thermally coupled to the photovoltaic cell to ensure proper tracking. A resistor placed in series with the diode can be used to adjust the DC set point to better match the maximum power point of a particular source if the selected diode forward voltage is too low. If the diode is located far from the converter inputs, a capacitor may be required to filter noise that may couple onto the MPPC pin, as shown in Figure 5. This method can be extended to stacked cell sources through use of multiple series connected diodes. MPPC LTC3105 3105 F02 3105 F04 Figure 2. FB Configuration Figure 4. MPPC Configuration LDO R3 LTC3105 FBLDO R4 2.2V LDO LTC3105 FBLDO VFWD RMPPC 10µA MPPC LTC3105 + – C6 10nF 3105 F03 3105 F05 Figure 3. FBLDO Configuration Figure 5. MPPC Configuration with Temperature Adjustment 3105fa 11 LTC3105 APPLICATIONS INFORMATION Industrial Current Loops The low 250mV start-up and low voltage operation of the LTC3105 allow it to be supplied by power from a diode placed in an industrial sensor current loop, as shown in Figure 6. In this application, a large input capacitor is required due to the very low available supply current (less than 4mA). The loop diode should be selected for a minimum forward drop of 300mV. The MPPC pin voltage should be set for a value approximately 50mV below the minimum diode forward voltage. 4mA TO 20mA CURRENT LOOP VFWD + VIN CIN LTC3105 GND RMPPC MPPC 3105 F06 – Figure 6. Current Loop Power Tap TYPICAL APPLICATIONS 3.3V from a Single-Cell Photovoltaic Source with Temperature Tracking L1** 10µH + – THERMALLY COUPLED VIN CIN 10µF SW VOUT LTC3105 FB R1 2.26M R2 1M VOUT 3.3V MPPC RMPPC OFF ON 9.09k SHDN AUX GND PGOOD LDO FBLDO CLDO 4.7µF 2.2V COUT 10µF D1* CMPPC 10nF CAUX 1µF * MRA4003T3 ** COILCRAFT MSS5131-103MX 3105 TA02 VMPPC vs Temperature 0.7 0.6 MPPC VOLTAGE (V) 0.5 0.4 0.3 0.2 0.1 0 –45 –30 –15 MPPC Response to Input Source Current Step VOUT = 2.8V VMPPC = 0.4V VFB = 0.94V INPUT VOLTAGE 50mV/DIV INPUT CURRENT 25mA/DIV OUTPUT CURRENT 5mA/DIV 0 15 30 45 60 TEMPERATURE (°C) 75 90 3105 TA02a 0.38V 10mA 0.7mA 25µs/DIV 3105 TA02b 3105fa 12 LTC3105 TYPICAL APPLICATIONS 3.3V from Multiple Stacked-Cell Photovoltaic with Source Temperature Tracking L1** 6.8µH + – + – THERMALLY COUPLED D1* D2* RMPPC 4.99k MPPC OFF ON CMPPC 10nF CAUX 1µF SHDN AUX GND CIN 10µF VIN SW VOUT LTC3105 FB PGOOD LDO FBLDO CLDO 4.7µF 3105 TA03 R1 1.37M R2 604k VOUT 3.3V COUT 10µF 2.2V * MRA4003T3 ** PANASONIC ELL-VEG6R8N Thermoelectric Generator to 2.4V Super Capacitor Charger L1** 10µH ∆T ≥ 10°C + TEG* VIN CIN 100µF SW VOUT LTC3105 FB CFF 22pF R1 1.10M R2 787k VOUT 2.4V COUT 1µF MPPC OFF ON RMPPC 30.1k SHDN AUX CAUX 1µF GND PGOOD LDO FBLDO CLDO 4.7µF 2.2V + CBULK 1F 2.5V 3105 TA04 * MICROPELT MPG-D751 ** COILCRAFT MSS5131-103MX 3105fa 13 LTC3105 TYPICAL APPLICATIONS Industrial Sensor 4mA to 20mA Current Loop Power Tap L1** 10µH VIN LTC3105 FB CIN 470µF 280mV RMPPC 28k * MBRS190T3 ** COILCRAFT MSS5131-103MX OFF ON CAUX 1µF MPPC SHDN AUX GND 3105 TA05 SW VOUT R1 2M EN µP VDD CLDO 4.7µF R2 1M 10µF 4mA TO 20mA CURRENT LOOP VFWD = 330mV PGOOD LDO D1* RPG 499k 2.2V + VOUT, 3V – FBLDO Transient Response to Load Pulse with 4mA Loop Current VOUT VOLTAGE 250mV/DIV Start-Up VIN, VOUT , VLDO VOUT VOLTAGE 500mV/DIV LDO VOLTAGE 500mV/DIV VIN VOLTAGE 50mV/DIV 0V LOAD CURRENT 2mA/DIV 100mV 2ms/DIV 3105 TA05a VIN VOLTAGE 200mV/DIV 50ms/DIV 3105 TA05b Single-Cell Photovoltaic NiMH Trickle Charger L1, 10µH + – VIN CIN 10µF SW VOUT LTC3105 FB R1 1.02M R2 470k 1.8V R3 1M CLDO 4.7µF COUT 10µF + + NiMH ×2 VOUT 3.2V MPPC OFF ON RMPPC 40.2k CAUX 1µF SHDN PGOOD LDO AUX GND FBLDO R4 1.27M 3105 TA06 3105fa 14 LTC3105 PACKAGE DESCRIPTION DD Package DD Package 10-Lead Plastic DFN (3mm × 3mm) 10-Lead Plastic DFN (3mm × (Reference LTC DWG # 05-08-1699 Rev C) 3mm) (Reference LTC DWG # 05-08-1699 Rev C) 0.70 ±0.05 3.55 ±0.05 1.65 ±0.05 2.15 ±0.05 (2 SIDES) PACKAGE OUTLINE 0.25 ± 0.05 0.50 BSC 2.38 ±0.05 (2 SIDES) R = 0.125 TYP 6 0.40 ± 0.10 10 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 3.00 ±0.10 (4 SIDES) PIN 1 TOP MARK (SEE NOTE 6) 0.200 REF 0.75 ±0.05 1.65 ± 0.10 (2 SIDES) PIN 1 NOTCH R = 0.20 OR 0.35 × 45° CHAMFER 5 2.38 ±0.10 (2 SIDES) 1 (DD) DFN REV C 0310 0.25 ± 0.05 0.50 BSC 0.00 – 0.05 BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2). CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3105fa 15 LTC3105 PACKAGE DESCRIPTION MS Package 12-Lead Plastic MSOP MS Package (Reference LTC DWG # 05-08-1668 Rev Ø) 12-Lead Plastic MSOP (Reference LTC DWG # 05-08-1668 Rev Ø) 0.889 ± 0.127 (.035 ± .005) 5.23 (.206) MIN 3.20 – 3.45 (.126 – .136) 0.42 ± 0.038 (.0165 ± .0015) TYP 0.65 (.0256) BSC 4.039 ± 0.102 (.159 ± .004) (NOTE 3) 12 11 10 9 8 7 RECOMMENDED SOLDER PAD LAYOUT DETAIL “A” 0° – 6° TYP 0.406 ± 0.076 (.016 ± .003) REF 0.254 (.010) GAUGE PLANE 4.90 ± 0.152 (.193 ± .006) 3.00 ± 0.102 (.118 ± .004) (NOTE 4) 0.53 ± 0.152 (.021 ± .006) DETAIL “A” 0.18 (.007) SEATING PLANE 1.10 (.043) MAX 123456 0.86 (.034) REF NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.22 – 0.38 (.009 – .015) TYP 0.650 (.0256) BSC 0.1016 ± 0.0508 (.004 ± .002) MSOP (MS12) 1107 REV Ø 3105fa 16 LTC3105 REVISION HISTORY REV A DATE 02/11 DESCRIPTION Added (Note 5) notation to Input Start-Up Voltage conditions Added Note 5 Updated Start-Up Mode Operation section PAGE NUMBER 3 3 8 3105fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 17 LTC3105 TYPICAL APPLICATION Single-Cell Powered Remote Wireless Sensor L1* 10µH + – VIN CIN 10µF LTC3105 MPPC SW VOUT R1 2.32M FB R2 1.02M COUT 100µF VOUT 3.3V XMTR RMPPC 40.2k OFF ON PGOOD SHDN AUX 2N7000 CAUX 1µF GND LDO FBLDO I/O EN 2.2V RPG 499k VDD CLDO 4.7µF µC A/D SENSOR GPIO GND * COILCRAFT MSS5131-103MX 3105 TA07 RELATED PARTS PART NUMBER LTC3108/LTC3108-1 LTC3109 LTC4070 LTC4071 LTC3588-1/LTC3588-2 LTC3388-1/LTC3388-3 LTC3225/LTC3225-1 DESCRIPTION Ultralow Voltage Step-Up Converter and Power Manager Auto-Polarity, Ultralow Voltage Step-Up Converter and Power Manager Li-Ion/Polymer Shunt Battery Charger System Li-Ion/Polymer Shunt Battery Charger System with Low Battery Disconnect Piezoelectric Energy Harvesting Power Supply 20V High Efficiency Nanopower Step-Down Regulator 150mA Super Capacitor Charger COMMENTS VIN : 0.02V to 1V; VOUT = 2.2V, 2.35V, 3.3V, 4.1V, 5V; IQ = 6μA; 4mm × 3mm DFN-12, SSOP-16 Packages; LTC3108-1 VOUT = 2.2V, 2.5V, 3V, 3.7V, 4.5V |VIN |: 0.03V to 1V; VOUT = 2.2V, 2.35V, 3.3V, 4.1V, 5V; IQ = 7μA; 4mm × 4mm QFN-20, SSOP-20 Packages 450nA IQ; 1% Float Voltage Accuracy; 50mA Shunt Current 4.0V/4.1V/4.2V 550nA IQ; 1% Float Voltage Accuracy;