LTC3850EUFD-PBF

FEATURES n n n n n n n n n n n n n LTC3850/LTC3850-1 Dual, 2-Phase Synchronous Step-Down Switching Controller DESCRIPTION The LTC®3850 is a high performance dual synchronous step-down switching regulator controller that drives all N-channel power MOSFET stages. A constant-frequency current mode architecture allows a phase-lockable frequency of up to 780kHz. Power loss and supply noise are minimized by operating the two controller output stages out of phase. OPTI-LOOP® compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The LTC3850 features a precision 0.8V reference and a power good output indicator. A wide 4V to 24V (28V maximum/30V for LTC3850I) input supply range encompasses most battery chemistries and intermediate bus voltages. Independent TK/SS pins for each controller ramp the output voltages during start-up. Current foldback limits MOSFET heat dissipation during short-circuit conditions. The MODE/PLLIN pin selects among Burst Mode® operation, pulse-skipping mode, or continuous inductor current mode and allows the IC to be synchronized to an external clock. The LTC3850 is available in low profile 28-pin 4mm × 4mm, 4mm × 5mm QFN and narrow SSOP packages. Dual, 180° Phased Controllers Reduce Required Input Capacitance and Power Supply Induced Noise High Efficiency: Up to 95% RSENSE or DCR Current Sensing ±1% 0.8V Output Voltage Accuracy Phase-Lockable Fixed Frequency 250kHz to 780kHz Supports Pre-Biased Output Dual N-Channel MOSFET Synchronous Drive Wide VIN Range: 4V to 24V (30V for LTC3850I) Operation Adjustable Soft-Start Current Ramping or Tracking Foldback Output Current Limiting Output Overvoltage Protection Power Good Output Voltage Monitor 28-Pin 4mm × 4mm, 4mm × 5mm QFN and Narrow SSOP Packages APPLICATIONS n n n n Notebook and Palmtop Computers Portable Instruments Battery-Operated Digital Devices DC Power Distribution Systems L, LT, LTC, LTM, OPTI-LOOP and BURST MODE are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 5481178, 5705919, 5929620, 6100678, 6144194, 6177787, 6304066, 6580258. TYPICAL APPLICATION High Efficiency Dual 3.3V/2.5V Step-Down Converter 4.7μF VIN PGOOD INTVCC 0.1μF 2.2μH TG1 BOOST1 SW1 BG1 2.2k 500kHz LTC3850 TG2 BOOST2 SW2 BG2 PGND FREQ/PLLFLTR SENSE2+ RUN2 SENSE2– VFB2 ITH2 SGND TK/SS2 0.1μF 10nF 10k 220pF 15k 20k 38501 TA01 Efficiency 22μF 50V VIN 7V TO 24V 100 VIN = 12V 95 VOUT = 3.3V 90 85 80 75 70 65 60 100 POWER LOSS 10000 EFFICIENCY 0.1μF 2.2μH 2.2k EFFICIENCY (%) POWER LOSS (mW) 1000 MODE/PLLIN ILIM SENSE1+ RUN1 SENSE1– VFB1 ITH1 TK/SS1 0.1μF VOUT1 3.3V 5A 100μF 6V 0.1μF VOUT2 2.5V 5A 100μF 6V 55 50 10 100 1000 LOAD CURRENT (mA) 10 10000 38501 TA01b 63.4k 220pF 20k 15k 43.2k 0.1μF 38501fb 1 LTC3850/LTC3850-1 ABSOLUTE MAXIMUM RATINGS (Note 1) Input Supply Voltage (VIN) ......................... 28V to –0.3V Input Supply Voltage (VIN), LTC3850I Only ....................................... 30V to –0.3V Input Supply Transient Voltage (VIN) < 500ms, with INTVCC ≥ 5V, LTC3850I Only................... 34V to –0.3V Top Side Driver Voltages BOOST1, BOOST2.................................. 34V to –0.3V Switch Voltage (SW1, SW2) ......................... 28V to –5V Switch Voltage (SW1, SW2), LTC3850I Only ....................................... 30V to –0.3V INTVCC , RUN1, RUN2, PGOOD, EXTVCC, (BOOST1-SW1), (BOOST2-SW2) ................. 6V to –0.3V SENSE1+, SENSE2+, SENSE1–, SENSE2– Voltages..................................... 5.5V to –0.3V MODE/PLLIN, ILIM,TK/SS1,TK/SS2, FREQ/PLLFLTR Voltages ................................................ INTVCC to –0.3V ITH1 , ITH2 , VFB1 , VFB2 Voltages .................. 2.7V to –0.3V INTVCC Peak Output Current ................................100mA Operating Temperature Range (Note 2)....–40°C to 85°C Junction Temperature (Note 3) ............................. 125°C Storage Temperature Range...................–65°C to 125°C Lead Temperature (Soldering, 10 sec) (GN Package) .................................................... 300°C PIN CONFIGURATION TOP VIEW RUN1 SENSE1+ SENSE1– TK/SS1 ITH1 VFB1 SGND VFB2 ITH2 1 2 3 4 5 6 7 8 9 28 FREQ/PLLFLTR SENSE1– 27 MODE/PLLIN 26 SW1 25 TG1 24 BOOST1 23 BG1 22 VIN 21 INTVCC 20 BG2 19 PGND 18 BOOST2 17 TG2 16 SW2 15 PGOOD TK/SS1 1 ITH1 2 VFB1 3 VFB2 4 ITH2 5 TK/SS2 6 SENSE2– 7 8 SENSE2+ 9 10 11 12 13 14 EXTVCC ILIM SW2 RUN2 PGOOD TG2 29 SENSE1+ RUN1 TOP VIEW FREQ/PLLFLTR MODE/PLLIN SW1 28 27 26 25 24 23 22 21 BOOST1 20 BG1 19 VIN 18 INTVCC 17 BG2 16 PGND 15 BOOST2 TK/SS2 10 SENSE2– 11 SENSE2+ 12 RUN2 13 ILIM (EXTVCC)* 14 GN PACKAGE 28-LEAD NARROW PLASTIC SSOP UF PACKAGE 28-LEAD (4mm × 4mm) PLASTIC QFN TJMAX = 125°C, θJA = 95°C/W *PIN 14 = ILIM FOR LTC3850GN, EXTVCC FOR LTC3850GN-1 TOP VIEW FREQ/PLLFLTR MODE/PLLIN TJMAX = 125°C, θJA = 37°C/W, θJC = 2.6°C/W EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB SENSE1+ RUN1 SW1 28 27 26 25 24 23 SENSE1– 1 TK/SS1 2 ITH1 3 VFB1 4 VFB2 5 ITH2 6 TK/SS2 7 SENSE2– 8 9 10 11 12 13 14 SENSE2+ ILIM EXTVCC RUN2 PGOOD SW2 29 22 BOOST1 21 BG1 20 VIN 19 INTVCC 18 BG2 17 PGND 16 BOOST2 15 TG2 UFD PACKAGE 28-LEAD (4mm × 5mm) PLASTIC QFN TJMAX = 125°C, θJA = 34°C/W, EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB 38501fb 2 TG1 TG1 LTC3850/LTC3850-1 ORDER INFORMATION LEAD FREE FINISH LTC3850EGN#PBF LTC3850EGN-1#PBF LTC3850IGN#PBF LTC3850IGN-1#PBF LTC3850EUF#PBF LTC3850EUFD#PBF LTC3850IUF#PBF LTC3850IUFD#PBF TAPE AND REEL LTC3850EGN#TRPBF LTC3850EGN-1#TRPBF LTC3850IGN#TRPBF LTC3850IGN-1#TRPBF LTC3850EUF#TRPBF LTC3850EUFD#TRPBF LTC3850IUF#TRPBF LTC3850IUFD#TRPBF PART MARKING LTC3850GN LTC3850GN-1 LTC3850GN LTC3850GN-1 3850 3850 3850 3850 PACKAGE DESCRIPTION 28-Lead Narrow Plastic SSOP 28-Lead Narrow Plastic SSOP 28-Lead Narrow Plastic SSOP 28-Lead Narrow Plastic SSOP 28-Lead (4mm × 4mm) Plastic QFN 28-Lead (4mm × 5mm) Plastic QFN 28-Lead (4mm × 4mm) Plastic QFN 28-Lead (4mm × 5mm) Plastic QFN TEMPERATURE RANGE –40°C to 85°C –40°C to 85°C –40°C to 85°C –40°C to 85°C –40°C to 85°C –40°C to 85°C –40°C to 85°C –40°C to 85°C Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 38501fb 3 LTC3850/LTC3850-1 ELECTRICAL CHARACTERISTICS SYMBOL VFB1,2 IFB1,2 VREFLNREG VLOADREG PARAMETER Regulated Feedback Voltage Feedback Current Reference Voltage Line Regulation Output Voltage Load Regulation Main Control Loops ITH1,2 Voltage = 1.2V; (Note 4) (Note 4) VIN = 6V to 24V (Note 4) (Note 4) Measured in Servo Loop; ΔITH Voltage = 1.2V to 0.7V Measured in Servo Loop; ΔITH Voltage = 1.2V to 1.6V ITH1,2 = 1.2V; Sink/Source 5μA; (Note 4) (Note 5) VIN = 15V; EXTVCC Tied to VOUT1; VOUT1 = 5V VRUN1,2 = 0V VINTVCC Ramping Down In Dropout Measured at VFB1,2 (Each Channel) VSENSE1,2 = 3.3V VTK/SS1,2 = 0V VRUN1, VRUN2 Rising VFB1,2 = 0.7V, VSENSE1,2 = 3.3V, ILIM = 0V VFB1,2 = 0.7V, VSENSE1,2 = 3.3V, ILIM = Float VFB1,2 = 0.7V, VSENSE1,2 = 3.3V, ILIM = INTVCC TG High TG Low BG High BG Low (Note 6) CLOAD = 3300pF CLOAD = 3300pF (Note 6) CLOAD = 3300pF CLOAD = 3300pF CLOAD = 3300pF Each Driver CLOAD = 3300pF Each Driver (Note 7) 7V < VIN < 24V ICC = 0mA to 50mA EXTVCC Ramping Positive ICC = 20mA, VEXTVCC = 5V l l l l l l l l l The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C, VIN = 15V, VRUN1,2 = 5V, unless otherwise noted. CONDITIONS MIN 0.792 TYP 0.800 –10 0.002 0.01 –0.01 2.2 850 30 3 0.5 96 0.84 0.9 1.1 20 40 60 97.2 0.86 ±1 1.3 1.22 80 30 50 75 2.6 1.5 2.4 1.1 25 25 25 25 30 30 90 4.8 4.5 5 0.5 4.7 50 200 100 5.2 2 40 60 90 0.88 ±2 1.7 1.35 MAX 0.808 –50 0.02 0.1 –0.1 UNITS V nA %/V % % mmho μA μA V V % V μA μA V mV mV mV mV Ω Ω Ω Ω ns ns ns ns ns ns ns V % V mV mV gm1,2 IQ Transconductance Amplifier gm Input DC Supply Current Normal Mode Shutdown Undervoltage Lockout on INTVCC UVLO Hysteresis Maximum Duty Factor Feedback Overvoltage Lockout Sense Pin Bias Current Soft-Start Charge Current RUN Pin ON Threshold RUN Pin ON Hysteresis Maximum Current Sense Threshold (Note 8) TG Driver Pull-Up On-Resistance TG Driver Pulldown On-Resistance BG Driver Pull-Up On-Resistance BG Driver Pulldown On-Resistance TG Transition Time: Rise Time Fall Time BG Transition Time: Rise Time Fall Time Top Gate Off to Bottom Gate On Delay Synchronous Switch-On Delay Time Bottom Gate Off to Top Gate On Delay Top Switch-On Delay Time Minimum On-Time Internal VCC Voltage INTVCC Load Regulation EXTVCC Switchover Voltage EXTVCC Voltage Drop EXTVCC Hysteresis 50 UVLO UVLOHYS DFMAX VOVL ISENSE ITK/SS1,2 VRUN1,2 VRUN1,2HYS VSENSE(MAX) TG RUP TG RDOWN BG RUP BG RDOWN TG1,2 tr TG1,2 tf BG1,2 tr BG1,2 tf TG/BG t1D BG/TG t2D tON(MIN) VINTVCC VLDO INT VEXTVCC VLDO EXT VLDOHYS INTVCC Linear Regulator 38501fb 4 LTC3850/LTC3850-1 ELECTRICAL CHARACTERISTICS SYMBOL fNOM fLOW fHIGH RMODE/PLLIN IFREQ PARAMETER Nominal Frequency Lowest Frequency Highest Frequency MODE/PLLIN Input Resistance Phase Detector Output Current Sinking Capability Sourcing Capability PGOOD Voltage Low PGOOD Leakage Current PGOOD Trip Level fMODE < fOSC fMODE > fOSC IPGOOD = 2mA VPGOOD = 5V VFB with Respect to Set Regulated Voltage VFB Ramping Negative VFB Ramping Positive –5 5 – 7.5 7.5 Oscillator and Phase-Locked Loop VFREQ = 1.2V VFREQ = 0V VFREQ ≥ 2.4V 450 210 700 500 250 780 250 –13 13 0.1 0.3 ±2 –10 10 550 290 860 kHz kHz kHz kΩ μA μA V μA % % The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C, VIN = 15V, VRUN1,2 = 5V, unless otherwise noted. CONDITIONS MIN TYP MAX UNITS PGOOD Output VPGL IPGOOD VPG Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3850E/LTC3850E-1 are guaranteed to meet performance specifications from 0°C to 85°C. Specifications over the –40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3850I/LTC3850I-1 are guaranteed to meet performance specifications over the –40°C to 85°C operating temperature range. Note 3: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formulas: LTC3850GN: TJ = TA + (PD • 95°C/W) LTC3850UF: TJ = TA + (PD • 37°C/W) LTC3850UFD: TJ = TA + (PD • 43°C/W) Note 4: The LTC3850 is tested in a feedback loop that servos VITH1,2 to a specified voltage and measures the resultant VFB1,2. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See Applications Information. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. Note 7: The minimum on-time condition is specified for an inductor peak-to-peak ripple current ≥40% of IMAX (see Minimum On-Time Considerations in the Applications Information section). Note 8: VSENSE(MAX) defaults to 50mV typical for the LTC3850-1. TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Output Current and Mode 100 VIN = 12V 90 VOUT = 1.8V 80 EFFICIENCY (%) 70 60 50 40 30 20 10 0 10 100 1000 LOAD CURRENT (mA) 10000 38501 G01 Efficiency vs Output Current and Mode 100 90 BURST EFFICIENCY (%) 80 DCM EFFICIENCY (%) 70 60 50 40 30 20 10 0 10 VIN = 12V VOUT = 3.3V 100 1000 LOAD CURRENT (mA) 10000 38501 G02 Efficiency and Power Loss vs Input Voltage 100 VOUT = 3.3V IOUT = 2A EFFICIENCY 2000 BURST 95 1500 POWER LOSS (mW) DCM 90 POWER LOSS 85 1000 CCM CCM 500 80 5 10 15 20 INPUT VOLTAGE (V) 0 25 38501 G03 CIRCUIT OF FIGURE 14 CIRCUIT OF FIGURE 14 CIRCUIT OF FIGURE 14 38501fb 5 LTC3850/LTC3850-1 TYPICAL PERFORMANCE CHARACTERISTICS Load Step (Burst Mode Operation) ILOAD 2A/DIV 200mA TO 2.5A IL 2A/DIV VOUT 100mV/DIV AC COUPLED 38501 G04 Load Step (Forced Continuous Mode) ILOAD 2A/DIV 200mA TO 2.5A IL 2A/DIV VOUT 100mV/DIV AC COUPLED 40μs/DIV CIRCUIT OF FIGURE 14 VIN = 12V, VOUT = 1.8V 40μs/DIV CIRCUIT OF FIGURE 14 VIN = 12V, VOUT = 1.8V 38501 G05 Load Step (Pulse-Skipping Mode) ILOAD 2A/DIV 200mA TO 2.5A IL 2A/DIV VOUT 100mV/DIV AC COUPLED FORCED CONTINUOUS MODE 2A/DIV Burst Mode OPERATION 2A/DIV PULSE-SKIPPING MODE 2A/DIV 40μs/DIV CIRCUIT OF FIGURE 14 VIN = 12V, VOUT = 1.8V 38501 G06 Inductor Current at Light Load 1μs/DIV CIRCUIT OF FIGURE 14 VIN = 12V, VOUT = 1.8V ILOAD = 100μA 38501 G07 Prebiased Output at 2V RUN1 2V/DIV VTK/SS 500mV/DIV Coincident Tracking VOUT 2V/DIV VOUT1, 3.3V 3Ω LOAD, 1V/DIV VFB 500mV/DIV 2.5ms/DIV 38501 G08 VOUT2, 1.8V 1.5Ω LOAD 1V/DIV 1ms/DIV 38501 G09 38501fb 6 LTC3850/LTC3850-1 TYPICAL PERFORMANCE CHARACTERISTICS Tracking Up and Down with External Ramp 5 TK/SS1 TK/SS2 2V/DIV VOUT1 3.3V 3Ω LOAD 1V/DIV VOUT2 1.8V 1.5Ω LOAD 1V/DIV 10ms/DIV Quiescent Current vs Input Voltage without EXTVCC 5.25 5.00 4 SUPPLY CURRENT (mA) INTVCC VOLTAGE (V) 4.75 4.50 4.25 4.00 3.75 0 3.50 5 10 15 INPUT VOLTAGE (V) 38501 G11 INTVCC Line Regulation 3 2 38501 G10 1 20 25 0 5 10 15 20 25 38501 G12 INPUT VOLTAGE (V) Current Sense Threshold vs ITH Voltage 80 CURRENT SENSE THRESHOLD (mV) ILIM = INTVCC 60 ILIM = FLOAT VSENSE (mV) 40 20 0 –20 –40 0 0.5 1 VITH (V) 1.5 2 38501 G13 Maximum Current Sense Threshold vs Common Mode Voltage 80 CURRENT SENSE THRESHOLD (mV) 70 60 50 40 30 20 10 0 0 4 3 VSENSE COMMON MODE VOLTAGE (V) 1 2 5 ILIM = GND ILIM = FLOAT ILIM = INTVCC 100 90 80 70 60 50 40 30 20 10 0 Maximum Current Sense Threshold vs Duty Cycle ILIM = INTVCC ILIM = FLOAT ILIM = GND ILIM = GND 0 20 40 60 DUTY CYCLE (%) 80 100 38501 G15 38501 G14 Maximum Current Sense Voltage vs Feedback Voltage (Current Foldback) MAXIMUM CURRENT SENSE VOLTAGE (mV) 80 ILIM = INTVCC 70 TK/SS CURRENT (μA) 60 50 40 30 20 10 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 FEEDBACK VOLTAGE (V) 38501 G16 TK/SS Pull-Up Current vs Temperature 2.00 1.75 ILIM = FLOAT 1.50 ILIM = GND 1.25 1.00 –50 –25 50 25 0 TEMPERATURE (°C) 75 100 38501 G17 38501fb 7 LTC3850/LTC3850-1 TYPICAL PERFORMANCE CHARACTERISTICS Shutdown (RUN) Threshold vs Temperature 1.5 REGULATED FEEDBACK VOLTAGE (mV) 806 804 802 800 798 796 794 –50 FREQUENCY (kHz) Regulated Feedback Voltage vs Temperature 900 800 700 600 500 400 300 Oscillator Frequency vs Temperature VFREQ = INTVCC 1.4 RUN PIN VOLTAGE (V) 1.3 ON 1.2 OFF 1.1 VFREQ = 1.2V VFREQ = 0V –25 50 25 0 TEMPERATURE (°C) 75 100 38501 G20 1.0 –50 –25 50 25 0 TEMPERATURE (°C) 75 100 38501 G18 –25 50 25 0 TEMPERATURE (°C) 75 100 38501 G19 200 –50 Undervoltage Lockout Threshold (INTVCC) vs Temperature 5 420 Oscillator Frequency vs Input Voltage 50 Shutdown Current vs Input Voltage 4 INTVCC VOLTAGE (V) FREQUENCY (kHz) RISING 3 FALLING 2 INPUT CURRENT (μA) 5 10 15 INPUT VOLTAGE (V) 20 25 38501 G22 410 40 30 400 20 390 1 10 0 –50 380 –25 50 25 0 TEMPERATURE (°C) 75 100 38501 G21 0 5 10 15 INPUT VOLTAGE (V) 38501 G23 20 25 Shutdown Current vs Temperature 50 VIN = 15V QUIESCENT CURRENT (mA) –25 50 25 0 TEMPERATURE (°C) 75 100 38501 G24 Quiescent Current vs Temperature without EXTVCC 5 SHUTDOWN CURRENT (μA) 40 4 30 3 20 2 10 1 0 –50 0 –50 –25 50 25 0 TEMPERATURE (°C) 75 100 38501 G25 38501fb 8 LTC3850/LTC3850-1 PIN FUNCTIONS (GN/UF/UFD) RUN1, RUN2 (Pins 1, 13/Pins 26, 9/Pins 27, 10): Run Control Inputs. A voltage above 1.2V on either pin turns on the IC. However, forcing either of these pins below 1.2V causes the IC to shut down that particular channel. There are 0.5μA pull-up currents for these pins. Once the RUN pin rises above 1.2V, an additional 4.5μA pull-up current is added to the pin. SENSE1+, SENSE2+ (Pins 2, 12/Pins 27, 8/Pins 28, 9): Current Sense Comparator Inputs. The (+) inputs to the current comparators are normally connected to DCR sensing networks or current sensing resistors. SENSE1–, SENSE2– (Pins 3, 11/Pins 28, 7/Pins 1, 8): Current Sense Comparator Inputs. The (–) inputs to the current comparators are connected to the outputs. TK/SS1, TK/SS2 (Pins 4, 10/Pins 1, 6/Pins 2, 7): Output Voltage Tracking and Soft-Start Inputs. When one channel is configured to be master of the two channels, a capacitor to ground at this pin sets the ramp rate for the master channel’s output voltage. When the channel is configured to be the slave of two channels, the VFB voltage of the master channel is reproduced by a resistor divider and applied to this pin. Internal soft-start currents of 1.3μA charge the soft-start capacitors. ITH1, ITH2 (Pins 5, 9/Pins 2, 5/Pins 3, 6): Current Control Thresholds and Error Amplifier Compensation Points. Each associated channels’ current comparator tripping threshold increases with its ITH control voltage. VFB1, VFB2 (Pins 6, 8/Pins 3, 4/Pins 4, 5): Error Amplifier Feedback Inputs. These pins receive the remotely sensed feedback voltages for each channel from external resistive dividers across the outputs. SGND (Pin 7/Pin 29/Pin 29): Signal Ground. All smallsignal components and compensation components should connect to this ground, which in turn connects to PGND at one point. Pin 29 is the Exposed Pad, only available on the UF package. EXTVCC (Pin 14, LTC3850-1 Only/Pin 11/Pin 12): External Power Input to an Internal Switch Connected to INTVCC. This switch closes and supplies the IC power, bypassing the internal low dropout regulator, whenever EXTVCC is higher than 4.7V. Do not exceed 6V on this pin and ensure VIN > VEXTVCC at all times. On the GN package, EXTVCC is the optional bonding in place of ILIM for LTC3850-1. In the LTC3850-1, ILIM will default to 50mV. ILIM (Pin 14, LTC3850 Only/Pin 10/Pin 11): Current Comparator Sense Voltage Range Inputs. Tying this pin to SGND, FLOAT or INTVCC sets the maximum current sense threshold to three different levels for each comparator. PGOOD (Pin 15/Pin 12/Pin 13): Power Good Indicator Output. Open-drain logic out that is pulled to ground when either channel output exceeds the ±7.5% regulation window, after the internal 17μs power bad mask timer expires. PGND (Pin 19/Pin 16/Pin 17): Power Ground Pin. Connect this pin closely to the sources of the bottom N-channel MOSFETs, the (–) terminal of CVCC and the (–) terminal of CIN. INTVCC (Pin 21/Pin 18/Pin 19): Internal 5V Regulator Output. The control circuits are powered from this voltage. Decouple this pin to PGND with a 4.7μF low ESR tantalum or ceramic capacitor. VIN (Pin 22/Pin 19/Pin 20): Main Input Supply. Decouple this pin to PGND with a capacitor (0.1μF to 1μF). For applications where the main input power is 5V, tie the VIN and INTVCC pins together. BG1, BG2 (Pins 23, 20/Pins 20, 17/Pins 21, 18): Bottom Gate Driver Outputs. These pins drive the gates of the bottom N-Channel MOSFETs and swings between PGND and INTVCC. BOOST1, BOOST2 (Pins 24, 18/Pins 21, 15/Pins 22, 16): Boosted Floating Driver Supplies. The (+) terminal of the boost-strap capacitors connect to these pins. These pins swing from a diode voltage drop below INTVCC up to VIN + INTVCC. TG1, TG2 (Pins 25, 17/Pins 22, 14/Pins 23, 15): Top Gate Driver Outputs. These are the outputs of floating drivers with a voltage swing equal to INTVCC superimposed on the switch nodes voltages. SW1, SW2 (Pins 26, 16/Pins 23, 13/Pins 24, 14): Switch Node Connections to Inductors. Voltage swing at these pins are from a body diode voltage drop below ground to VIN. 38501fb 9 LTC3850/LTC3850-1 PIN FUNCTIONS MODE/PLLIN (Pin 27/Pin 24/Pin 25): Force Continuous Mode, Burst Mode, or Pulse-Skipping Mode Selection Pin and External Synchronization Input to Phase Detector Pin. Connect this pin to SGND to force both channels into the continuous mode of operation. Connect to INTVCC to enable pulse-skipping mode of operation. Leaving the pin floating will enable Burst Mode operation. A clock on the pin will force the controller into continuous mode of operation and synchronize the internal oscillator. FREQ/PLLFLTR (Pin 28/Pin 25/Pin 26): The Phase-Locked Loop’s Low-Pass Filter is Tied to This Pin. Alternatively, this pin can be driven with a DC voltage to vary the frequency of the internal oscillator. Exposed Pad (Pin 29, UF/UFD Packages Only): Signal Ground. Must be soldered to PCB, providing a local ground for the control components of the IC, and be tied to the PGND pin under the IC. FUNCTIONAL DIAGRAM FREQ/PLLFLTR MODE/PLLIN EXTVCC 4.7V VIN VIN + CIN – MODE/SYNC DETECT PLL-SYNC 0.8V F + 5V REG – F + INTVCC INTVCC BOOST OSC S R Q FCNT BURSTEN TG SW SWITCH LOGIC AND ANTISHOOT THROUGH SENSE+ SENSE– CB M1 L1 VOUT DB + ICMP 3k ON – IREV – + RUN + COUT OV BG M2 CVCC PGND PGOOD ILIM SLOPE COMPENSATION INTVCC UVLO + 1 51k ITHB SLOPE RECOVERY ACTIVE CLAMP 0.74V VFB R2 UV – VIN SLEEP OV + – EA 0.86V SGND 1.3μA R1 0.64V 1.2V 0.5μA 38501 FD 0.55V CC1 CSS ITH RC RUN 10 + + 0.8V REF – SS RUN – –++ + – TK/SS 38501fb LTC3850/LTC3850-1 OPERATION Main Control Loop The LTC3850 is a constant-frequency, current mode stepdown controller with two channels operating 180 degrees out-of-phase. During normal operation, each top MOSFET is turned on when the clock for that channel sets the RS latch, and turned off when the main current comparator, ICMP, resets the RS latch. The peak inductor current at which ICMP resets the RS latch is controlled by the voltage on the ITH pin, which is the output of each error amplifier EA. The VFB pin receives the voltage feedback signal, which is compared to the internal reference voltage by the EA. When the load current increases, it causes a slight decrease in VFB relative to the 0.8V reference, which in turn causes the ITH voltage to increase until the average inductor current matches the new load current. After the top MOSFET has turned off, the bottom MOSFET is turned on until either the inductor current starts to reverse, as indicated by the reverse current comparator IREV, or the beginning of the next cycle. INTVCC/EXTVCC Power Power for the top and bottom MOSFET drivers and most other internal circuitry is derived from the INTVCC pin. When the EXTVCC pin is left open or tied to a voltage less than 4.7V, an internal 5V linear regulator supplies INTVCC power from VIN. If EXTVCC is taken above 4.7V, the 5V regulator is turned off and an internal switch is turned on connecting EXTVCC. Using the EXTVCC pin allows the INTVCC power to be derived from a high efficiency external source such as one of the LTC3850 switching regulator outputs. Each top MOSFET driver is biased from the floating bootstrap capacitor CB, which normally recharges during each off cycle through an external diode when the top MOSFET turns off. If the input voltage VIN decreases to a voltage close to VOUT, the loop may enter dropout and attempt to turn on the top MOSFET continuously. The dropout detector detects this and forces the top MOSFET off for about one-twelfth of the clock period every third cycle to allow CB to recharge. However, it is recommended that a load be present during the drop-out transition to ensure CB is recharged. Shutdown and Start-Up (RUN1, RUN2 and TK/SS1, TK/SS2 Pins) The two channels of the LTC3850 can be independently shut down using the RUN1 and RUN2 pins. Pulling either of these pins below 1.2V shuts down the main control loop for that controller. Pulling both pins low disables both controllers and most internal circuits, including the INTVCC regulator. Releasing either RUN pin allows an internal 0.5μA current to pull up the pin and enable that controller. Alternatively, the RUN pin may be externally pulled up or driven directly by logic. Be careful not to exceed the Absolute Maximum Rating of 6V on this pin. The start-up of each controller’s output voltage VOUT is controlled by the voltage on the TK/SS1 and TK/SS2 pins. When the voltage on the TK/SS pin is less than the 0.8V internal reference, the LTC3850 regulates the VFB voltage to the TK/SS pin voltage instead of the 0.8V reference. This allows the TK/SS pin to be used to program a soft-start by connecting an external capacitor from the TK/SS pin to SGND. An internal 1.3μA pull-up current charges this capacitor, creating a voltage ramp on the TK/SS pin. As the TK/SS voltage rises linearly from 0V to 0.8V (and beyond), the output voltage VOUT rises smoothly from zero to its final value. Alternatively the TK/SS pin can be used to cause the start-up of VOUT to “track” that of another supply. Typically, this requires connecting to the TK/SS pin an external resistor divider from the other supply to ground (see the Applications Information section). When the corresponding RUN pin is pulled low to disable a controller, or when INTVCC drops below its undervoltage lockout threshold of 3V, the TK/SS pin is pulled low by an internal MOSFET. When in undervoltage lockout, both controllers are disabled and the external MOSFETs are held off. Light Load Current Operation (Burst Mode Operation, Pulse-Skipping, or Continuous Conduction) The LTC3850 can be enabled to enter high efficiency Burst Mode operation, constant-frequency pulse-skipping mode, or forced continuous conduction mode. To select forced continuous operation, tie the MODE/PLLIN pin to a DC voltage below 0.8V (e.g., SGND). To select pulse-skipping mode of operation, tie the MODE/PLLIN pin to INTVCC. To select Burst Mode operation, float the MODE/PLLIN pin. 38501fb 11 LTC3850/LTC3850-1 OPERATION When a controller is enabled for Burst Mode operation, the peak current in the inductor is set to approximately one-third of the maximum sense voltage even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the load current, the error amplifier EA will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.5V, the internal sleep signal goes high (enabling “sleep” mode) and both external MOSFETs are turned off. In sleep mode, the load current is supplied by the output capacitor. As the output voltage decreases, the EA’s output begins to rise. When the output voltage drops enough, the sleep signal goes low, and the controller resumes normal operation by turning on the top external MOSFET on the next cycle of the internal oscillator. When a controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reverse current comparator (IREV) turns off the bottom external MOSFET just before the inductor current reaches zero, preventing it from reversing and going negative. Thus, the controller operates in discontinuous operation. In forced continuous operation, the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as in normal operation. In this mode, the efficiency at light loads is lower than in Burst Mode operation. However, continuous mode has the advantages of lower output ripple and less interference with audio circuitry. When the MODE/PLLIN pin is connected to INTVCC, the LTC3850 operates in PWM pulse-skipping mode at light loads. At very light loads, the current comparator ICMP may remain tripped for several cycles and force the external top MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced RF interference as compared to Burst Mode operation. It provides higher low current efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. Frequency Selection and Phase-Locked Loop (FREQ/PLLFLTR and MODE/PLLIN Pins) The selection of switching frequency is a trade-off between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. The switching frequency of the LTC3850’s controllers can be selected using the FREQ/PLLFLTR pin. If the MODE/PLLIN pin is not being driven by an external clock source, the FREQ/PLLFLTR pin can be used to program the controller’s operating frequency from 250kHz to 780kHz. A phase-locked loop (PLL) is available on the LTC3850 to synchronize the internal oscillator to an external clock source that is connected to the MODE/PLLIN pin. The controller is operating in forced continuous mode when it is synchronized. A series R-C should be connected between the FREQ/PLLFLTR pin and SGND to serve as the PLL’s loop filter. Power Good (PGOOD Pin) The PGOOD pin is connected to an open drain of an internal N-channel MOSFET. The MOSFET turns on and pulls the PGOOD pin low when either VFB pin voltage is not within ±7.5% of the 0.8V reference voltage. The PGOOD pin is also pulled low when either RUN pin is below 1.2V or when the LTC3850 is in the soft-start or tracking phase. When the VFB pin voltage is within the ±7.5% requirement, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source of up to 6V. The PGOOD pin will flag power good immediately when both VFB pins are within the ±7.5% window. However, there is an internal 17μs power bad mask when either VFB goes out of the ±7.5% window. Output Overvoltage Protection An overvoltage comparator, OV, guards against transient overshoots (> 7.5%) as well as other more serious conditions that may overvoltage the output. In such cases, the top MOSFET is turned off and the bottom MOSFET is turned on until the overvoltage condition is cleared. 38501fb 12 LTC3850/LTC3850-1 APPLICATIONS INFORMATION The Typical Application on the first page is a basic LTC3850 application circuit. LTC3850 can be configured to use either DCR (inductor resistance) sensing or low value resistor sensing. The choice between the two current sensing schemes is largely a design trade-off between cost, power consumption, and accuracy. DCR sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and inductor value. Next, the power MOSFETs are selected. Finally, input and output capacitors are selected. Current Limit Programming The ILIM pin is a tri-level logic input which sets the maximum current limit of the controller. When ILIM is either grounded, floated or tied to INTVCC, the typical value for the maximum current sense threshold will be 30mV, 50mV or 75mV, respectively. Which setting should be used? For the best current limit accuracy, use the 75mV setting. The 30mV setting will allow for the use of very low DCR inductors or sense resistors, but at the expense of current limit accuracy. The 50mV setting is a good balance between the two. For single output dual phase applications (see Figure 21), use the 50mV or 75mV setting for optimal current sharing. SENSE+ and SENSE– Pins The SENSE+ and SENSE– pins are the inputs to the current comparators. The common mode input voltage range of the current comparators is 0V to 5V. Both SENSE pins are high impedance inputs with small base currents of less than 1μA. When the SENSE pins ramp up from 0V to 1.4V, the small base currents flow out of the SENSE pins. When the SENSE pins ramp down from 5V to 1.1V, the small base currents flow into the SENSE pins. The high impedance inputs to the current comparators allow accurate DCR sensing. However, care must be taken not to float these pins during normal operation. Filter components mutual to the sense lines should be placed close to the LTC3850, and the sense lines should run close together to a Kelvin connection underneath the current sense element (shown in Figure 1). Sensing current elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. If DCR sensing is used (Figure 2b), sense resistor R1 should be placed TO SENSE FILTER, NEXT TO THE CONTROLLER COUT INDUCTOR OR RSENSE 38501 F01 Figure 1. Sense Lines Placement with Inductor or Sense Resistor VIN INTVCC VIN VIN INTVCC BOOST TG VOUT LTC3850 SW BG VIN BOOST TG LTC3850 SW BG PGND SENSE+ SENSE– SGND 38501 F02a SENSE RESISTOR PLUS PARASITIC INDUCTANCE RS ESL INDUCTOR L DCR VOUT RF CF RF CF • 2RF ≤ ESL/RS POLE-ZERO CANCELLATION PGND SENSE+ C1* SENSE– SGND 38501 F02b R1 R2 FILTER COMPONENTS PLACED NEAR SENSE PINS *PLACE C1 NEAR SENSE+, SENSE– PINS R1||R2 × C1 = L DCR RSENSE(EQ) = DCR R2 R1 + R2 (2a) Using a Resistor to Sense Current (2b) Using the Inductor DCR to Sense Current Figure 2. Two Different Methods of Sensing Current 38501fb 13 LTC3850/LTC3850-1 APPLICATIONS INFORMATION close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. The capacitor C1 should be placed close to the IC pins. Low Value Resistors Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 2a. RSENSE is chosen based on the required output current. The current comparator has a maximum threshold VSENSE(MAX) determined by the ILIM setting. The input common mode range of the current comparator is 0V to 5V. The current comparator threshold sets the peak of the inductor current, yielding a maximum average output current IMAX equal to the peak value less half the peak-topeak ripple current, ΔIL. To calculate the sense resistor value, use the equation: RSENSE = VSENSE(MAX) I I(MAX) + L 2 reduce the effects of capacitive and inductive noise coupled inthe sense traces on the PCB. A typical filter consists of two series 10Ω resistors connected to a parallel 1000pF capacitor, resulting in a time constant of 20ns. This same RC filter, with minor modifications, can be used to extract the resistive component of the current sense signal in the presence of parasitic inductance. For example, Figure 3 illustrates the voltage waveform across a 2mΩ sense resistor with a 2010 footprint for the 1.2V/15A converter shown in Figure 18 operating at 100% load. The waveform is the superposition of a purely resistive component and a purely inductive component. It was measured using two scope probes and waveform math to obtain a differential measurement. Based on additional measurements of the inductor ripple current and the on-time and off-time of the top switch, the value of the parasitic inductance was determined to be 0.5nH using the equation: V t •t ESL = ESL(STEP) ON OFF ΔIL tON + tOFF If the RC time constant is chosen to be close to the parasitic inductance divided by the sense resistor (L/R), the resulting waveform looks resistive again, as shown in Figure 4. For applications using low maximum sense voltages, check the sense resistor manufacturer’s data sheet for information about parasitic inductance. In the absence of data, measure the voltage drop directly across the sense resistor to extract the magnitude of the ESL step and use the equation above to determine the ESL. However, do not over-filter. Keep the RC time constant less than or equal to the inductor time constant to maintain a high enough ripple voltage on VRSENSE. The above generally applies to high density / high current applications where I(MAX) > 10A and low values of inductors are used. For applications where I(MAX) < 10A, . set RF to 10 Ohms and CF to 1000pF This will provide a good starting point. The filter components need to be placed close to the IC. The positive and negative sense traces need to be routed as a differential pair and Kelvin connected to the sense resistor. Because of possible PCB noise in the current sensing loop, the AC current sensing ripple of ΔVSENSE = ΔIL • RSENSE also needs to be checked in the design to get a good signal-to-noise ratio. In general, for a reasonably good PCB layout, a 15mV ΔVSENSE voltage is recommended as a conservative number to start with, either for RSENSE or DCR sensing applications. For previous generation current mode controllers, the maximum sense voltage was high enough (e.g., 75mV for the LTC1628 / LTC3728 family) that the voltage drop across the parasitic inductance of the sense resistor represented a relatively small error. For today’s highest current density solutions, however, the value of the sense resistor can be less than 1mΩ and the peak sense voltage can be as low as 20mV. In addition, inductor ripple currents greater than 50% with operation up to 1MHz are becoming more common. Under these conditions the voltage drop across the sense resistor’s parasitic inductance is no longer negligible. A typical sensing circuit using a discrete resistor is shown in Figure 2a. In previous generations of controllers, a small RC filter placed near the IC was commonly used to 38501fb 14 LTC3850/LTC3850-1 APPLICATIONS INFORMATION Using the inductor ripple current value from the Inductor Value Calculation section, the target sense resistor value is: VSENSE(MAX) RSENSE(EQUIV) = I I(MAX) + L 2 To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value for the Maximum Current Sense Threshold (VSENSE(MAX)) in the Electrical Characteristics table (20mV, 40mV, or 60mV, depending on the state of the ILIM pin). Next, determine the DCR of the inductor. Where provided, use the manufacturer’s maximum value, usually given at 20°C. Increase this value to account for the temperature coefficient of resistance, which is approximately 0.4%/°C. A conservative value for TL(MAX) is 100°C. 500ns/DIV 38501 F04 VESL(STEP) VSENSE 20mV/DIV 500ns/DIV 38501 F03 Figure 3. Voltage Waveform Measured Directly Across the Sense Resistor. VSENSE 20mV/DIV Figure 4. Voltage Waveform Measured After the Sense Resistor Filter. CF = 1000pF RF = 100Ω. , To scale the maximum inductor DCR to the desired sense resistor value, use the divider ratio: RSENSE(EQUIV) RD = DCR(MAX) at TL(MAX) C1 is usually selected to be in the range of 0.047μF to 0.47μF This forces R1|| R2 to around 2kΩ, reducing error . that might have been caused by the SENSE pins’ ±1μA current. The equivalent resistance R1|| R2 is scaled to the room temperature inductance and maximum DCR: L R1||R2 = (DCR at 20°C) • C1 The sense resistor values are: R1|| R2 R1 • RD R1 = ; R2 = RD 1 RD The maximum power loss in R1 is related to duty cycle, and will occur in continuous mode at the maximum input voltage: VIN(MAX) VOUT • VOUT PLOSS R1= R1 Inductor DCR Sensing For applications requiring the highest possible efficiency at high load currents, the LTC3850 is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 2b. The DCR of the inductor represents the small amount of DC winding resistance of the copper, which can be less than 1mΩ for today’s low value, high current inductors. In a high current application requiring such an inductor, conduction loss through a sense resistor would cost several points of efficiency compared to DCR sensing. If the external R1|| R2 • C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the drop across the inductor DCR multiplied by R2/(R1 + R2). R2 scales the voltage across the sense terminals for applications where the DCR is greater than the target sense resistor value. To properly dimension the external filter components, the DCR of the inductor must be known. It can be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature; consult the manufacturers’ datasheets for detailed information. ( ) 38501fb 15 LTC3850/LTC3850-1 APPLICATIONS INFORMATION Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use DCR sensing or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. To maintain a good signal to noise ratio for the current sense signal, use a minimum ΔVSENSE of 10mV to 15mV. For a DCR sensing application, the actual ripple voltage will be determined by the equation: ΔVSENSE = VIN − VOUT VOUT R1• C1 VIN • fOSC A reasonable starting point is to choose a ripple current that is about 40% of IOUT(MAX). Note that the largest ripple current occurs at the highest input voltage. To guarantee that ripple current does not exceed a specified maximum, the inductor should be chosen according to: VIN – VOUT VOUT L • fOSC •IRIPPLE VIN Inductor Core Selection Once the inductance value is determined, the type of inductor must be selected. Core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core loss and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates “hard,” which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Power MOSFET and Schottky Diode (Optional) Selection Two external power MOSFETs must be selected for each controller in the LTC3850: one N-channel MOSFET for the top (main) switch, and one N-channel MOSFET for the bottom (synchronous) switch. The peak-to-peak drive levels are set by the INTVCC voltage. This voltage is typically 5V during start-up (see EXTVCC Pin Connection). Consequently, logic-level threshold MOSFETs must be used in most applications. The only exception is if low input voltage is expected (VIN < 5V); then, sub-logic level threshold MOSFETs (VGS(TH) < 3V) should be used. Pay close attention to the BVDSS specification for the MOSFETs as well; most of the logic level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the on-resistance RDS(ON) , Miller capacitance CMILLER, input 38501fb Slope Compensation and Inductor Peak Current Slope compensation provides stability in constantfrequency architectures by preventing subharmonic oscillations at high duty cycles. It is accomplished internally by adding a compensating ramp to the inductor current signal at duty cycles in excess of 40%. Normally, this results in a reduction of maximum inductor peak current for duty cycles > 40%. However, the LTC3850 uses a patented scheme that counteracts this compensating ramp, which allows the maximum inductor peak current to remain unaffected throughout all duty cycles. Inductor Value Calculation Given the desired input and output voltages, the inductor value and operating frequency fOSC directly determine the inductor’s peak-to-peak ripple current: IRIPPLE = VOUT VIN – VOUT VIN fOSC • L Lower ripple current reduces core losses in the inductor, ESR losses in the output capacitors, and output voltage ripple. Thus, highest efficiency operation is obtained at low frequency with a small ripple current. Achieving this, however, requires a large inductor. 16 LTC3850/LTC3850-1 APPLICATIONS INFORMATION voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturers’ data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS to the gate charge curve specified VDS. When the IC is operating in continuous mode the duty cycles for the top and bottom MOSFETs are given by: Main Switch Duty Cycle = VOUT VIN VIN – VOUT VIN a short-circuit when the synchronous switch is on close to 100% of the period. The term (1 + δ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs Temperature curve, but δ = 0.005/°C can be used as an approximation for low voltage MOSFETs. The optional Schottky diodes conduct during the dead time between the conduction of the two power MOSFETs. These prevent the body diodes of the bottom MOSFETs from turning on, storing charge during the dead time and requiring a reverse recovery period that could cost as much as 3% in efficiency at high VIN. A 1A to 3A Schottky is generally a good compromise for both regions of operation due to the relatively small average current. Larger diodes result in additional transition losses due to their larger junction capacitance. Soft-Start and Tracking The LTC3850 has the ability to either soft-start by itself with a capacitor or track the output of another channel or external supply. When one particular channel is configured to soft-start by itself, a capacitor should be connected to its TK/SS pin. This channel is in the shutdown state if its RUN pin voltage is below 1.2V. Its TK/SS pin is actively pulled to ground in this shutdown state. Once the RUN pin voltage is above 1.2V, the channel powers up. A soft-start current of 1.3μA then starts to charge its soft-start capacitor. Note that soft-start or tracking is achieved not by limiting the maximum output current of the controller but by controlling the output ramp voltage according to the ramp rate on the TK/SS pin. Current foldback is disabled during this phase to ensure smooth soft-start or tracking. The soft-start or tracking range is defined to be the voltage range from 0V to 0.8V on the TK/ SS pin. The total soft-start time can be calculated as: C t SOFTSTART = 0.8 • SS 1.3 μA Regardless of the mode selected by the MODE/PLLIN pin, the regulator will always start in pulse-skipping mode up to TK/SS = 0.64V. Between TK/SS = 0.64V and 0.74V, it will operate in forced continuous mode and revert to the 38501fb Synchronous Switch Duty Cycle = The MOSFET power dissipations at maximum output current are given by: V 2 PMAIN = OUT (IMAX ) (1+ δ) RDS(ON) + VIN ⎞ 2 ⎛I ( VIN ) ⎜ MAX ⎟ (RDR )(CMILLER ) • ⎝2⎠ ⎡ 1 1⎤ ⎢ ⎥ • fOSC + ⎢ VINTVCC – VTH(MIN) VTH(MIN) ⎥ ⎣ ⎦ V –V 2 PSYNC = IN OUT (IMAX ) (1+ δ) RDS(ON) VIN where δ is the temperature dependency of RDS(ON) and RDR (approximately 2Ω) is the effective driver resistance at the MOSFET’s Miller threshold voltage. VTH(MIN) is the typical MOSFET minimum threshold voltage. Both MOSFETs have I2R losses while the topside N-channel equation includes an additional term for transition losses, which are highest at high input voltages. For VIN < 20V the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during 17 LTC3850/LTC3850-1 APPLICATIONS INFORMATION selected mode once TK/SS > 0.74V. The output ripple is minimized during the 100mV forced continuous mode window ensuring a clean PGOOD signal. When the channel is configured to track another supply, the feedback voltage of the other supply is duplicated by a resistor divider and applied to the TK/SS pin. Therefore, the voltage ramp rate on this pin is determined by the ramp rate of the other supply’s voltage. Note that the small soft-start capacitor charging current is always flowing, producing a small offset error. To minimize this error, select the tracking resistive divider value to be small enough to make this error negligible. In order to track down another channel or supply after the soft-start phase expires, the LTC3850 is forced into continuous mode of operation as soon as VFB is below the undervoltage threshold of 0.74V regardless of the setting on the MODE/PLLIN pin. However, the LTC3850 should always be set in force continuous mode tracking down when there is no load. After TK/SS drops below 0.1V, its channel will operate in discontinuous mode. Output Voltage Tracking The LTC3850 allows the user to program how its output ramps up and down by means of the TK/SS pins. Through these pins, the output can be set up to either coincidentally or ratiometrically track another supply’s output, as shown in Figure 5. In the following discussions, VOUT1 refers to the LTC3850’s output 1 as a master channel and VOUT2 refers to the LTC3850’s output 2 as a slave channel. In practice, though, either phase can be used as the master. To implement the coincident tracking in Figure 5a, connect an additional resistive divider to VOUT1 and connect its midpoint to the TK/SS pin of the slave channel. The ratio of this divider should be the same as that of the slave channel’s feedback divider shown in Figure 6a. In this tracking mode, VOUT1 must be set higher than VOUT2. To implement the ratiometric tracking, the ratio of the VOUT2 divider should be exactly the same as the master channel’s feedback divider. By selecting different resistors, the LTC3850 can achieve different modes of tracking including the two in Figure 5. So which mode should be programmed? While either mode in Figure 5 satisfies most practical applications, some tradeoffs exist. The ratiometric mode saves a pair of resistors, but the coincident mode offers better output regulation. This can be better understood with the help of Figure 7. At the input stage of the slave channel’s error amplifier, two common anode diodes are used to clamp the equivalent reference voltage and an additional diode is used to match the shifted common mode voltage. The top two current sources are of the same amplitude. In the coincident mode, the TK/SS voltage is substantially higher than 0.8V at steady state and effectively turns off D1. D2 and D3 will therefore conduct the same current and offer tight matching between VFB2 and the internal precision 0.8V reference. In the ratiometric mode, however, TK/SS equals 0.8V at steady state. D1 will divert part of the bias current to make VFB2 slightly lower than 0.8V. Although this error is minimized by the exponential I-V characteristic of the diode, it does impose a finite amount of output voltage deviation. Furthermore, when the master channel’s output experiences dynamic excursion (under load transient, for example), the slave channel output will be affected as well. For better output regulation, use the coincident tracking mode instead of ratiometric. INTVCC Regulators and EXTVCC The LTC3850 features an NPN linear regulator that supplies power to INTVCC from the VIN supply. INTVCC powers the gate drivers and much of the LTC3850’s internal circuitry. The linear regulator regulates the voltage at the INTVCC pin to 5V when VIN is greater than 6.5V. EXTVCC connects to INTVCC through a P-channel MOSFET and can supply the needed power when its voltage is higher than 4.7V. Each of these can supply a peak current of 100mA and must be bypassed to ground with a minimum of 1μF ceramic capacitor or low ESR electrolytic capacitor. No matter what type of bulk capacitor is used, an additional 0.1μF ceramic capacitor placed directly adjacent to the INTVCC and PGND pins is highly recommended. Good bypassing is needed to supply the high transient currents required by the MOSFET gate drivers and to prevent interaction between the channels. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3850 to be 38501fb 18 LTC3850/LTC3850-1 APPLICATIONS INFORMATION VOUT1 OUTPUT VOLTAGE OUTPUT VOLTAGE VOUT1 VOUT2 VOUT2 TIME 38501 F03a TIME 38501 F03b (5a) Coincident Tracking (5b) Ratiometric Tracking Figure 5. Two Different Modes of Output Voltage Tracking VOUT1 R3 TO TK/SS2 PIN R4 R2 R1 TO VFB1 PIN TO VFB2 PIN R4 R3 VOUT2 VOUT1 R1 TO TK/SS2 PIN R2 TO VFB1 PIN TO VFB2 PIN R4 R3 VOUT2 38501 F06 (6a) Coincident Tracking Setup (6b) Ratiometric Tracking Setup Figure 6. Setup for Coincident and Ratiometric Tracking I I + D1 TK/SS2 0.8V VFB2 38501 F07 D2 EA2 – D3 Figure 7. Equivalent Input Circuit of Error Amplifier 38501fb 19 LTC3850/LTC3850-1 APPLICATIONS INFORMATION exceeded. The INTVCC current, which is dominated by the gate charge current, may be supplied by either the 5V linear regulator or EXTVCC. When the voltage on the EXTVCC pin is less than 4.7V, the linear regulator is enabled. Power dissipation for the IC in this case is highest and is equal to VIN • IINTVCC. The gate charge current is dependent on operating frequency as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equations given in Note 3 of the Electrical Characteristics. For example, the LTC3850 INTVCC current is limited to less than 24mA from a 24V supply in the GN package and not using the EXTVCC supply: TJ = 70°C + (24mA)(24V)(95°C/W) = 125°C To prevent the maximum junction temperature from being exceeded, the input supply current must be checked while operating in continuous conduction mode (MODE/PLLIN = SGND) at maximum VIN. When the voltage applied to EXTVCC rises above 4.7V, the INTVCC linear regulator is turned off and the EXTVCC is connected to the INTVCC. The EXTVCC remains on as long as the voltage applied to EXTVCC remains above 4.5V. Using the EXTVCC allows the MOSFET driver and control power to be derived from one of the LTC3850’s switching regulator outputs during normal operation and from the INTVCC when the output is out of regulation (e.g., start-up, short-circuit). If more current is required through the EXTVCC than is specified, an external Schottky diode can be added between the EXTVCC and INTVCC pins. Do not apply more than 6V to the EXTVCC pin and make sure that EXTVCC < VIN. Significant efficiency and thermal gains can be realized by powering INTVCC from the output, since the VIN current resulting from the driver and control currents will be scaled by a factor of (Duty Cycle)/(Switcher Efficiency). Tying the EXTVCC pin to a 5V supply reduces the junction temperature in the previous example from 125°C to: TJ = 70°C + (24mA)(5V)(95°C/W) = 81°C However, for 3.3V and other low voltage outputs, additional circuitry is required to derive INTVCC power from the output. The following list summarizes the four possible connections for EXTVCC: 1. EXTVCC left open (or grounded). This will cause INTVCC to be powered from the internal 5V regulator resulting in an efficiency penalty of up to 10% at high input voltages. 2. EXTVCC connected directly to VOUT. This is the normal connection for a 5V regulator and provides the highest efficiency. 3. EXTVCC connected to an external supply. If a 5V external supply is available, it may be used to power EXTVCC providing it is compatible with the MOSFET gate drive requirements. 4. EXTVCC connected to an output-derived boost network. For 3.3V and other low voltage regulators, efficiency gains can still be realized by connecting EXTVCC to an output-derived voltage that has been boosted to greater than 4.7V. For applications where the main input power is 5V, tie the VIN and INTVCC pins together and tie the combined pins to the 5V input with a 1Ω or 2.2Ω resistor as shown in Figure 8 to minimize the voltage drop caused by the gate charge current. This will override the INTVCC linear regulator and will prevent INTVCC from dropping too low due to the dropout voltage. Make sure the INTVCC voltage is at or exceeds the RDS(ON) test voltage for the MOSFET which is typically 4.5V for logic level devices. LTC3850 VIN RVIN 5V CINTVCC 4.7μF 1Ω INTVCC + CIN 38501 F08 Figure 8. Setup for a 5V Input Topside MOSFET Driver Supply (CB, DB) External bootstrap capacitors CB connected to the BOOST pins supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Functional Diagram is charged though external diode DB from INTVCC when the SW pin is low. When one of the topside MOSFETs is to be turned on, the driver places the CB voltage across the gate source of the desired MOSFET. This enhances the MOSFET and 38501fb 20 LTC3850/LTC3850-1 APPLICATIONS INFORMATION turns on the topside switch. The switch node voltage, SW, rises to VIN and the BOOST pin follows. With the topside MOSFET on, the boost voltage is above the input supply: VBOOST = VIN + VINTVCC. The value of the boost capacitor CB needs to be 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of the external Schottky diode must be greater than VIN(MAX). When adjusting the gate drive level, the final arbiter is the total input current for the regulator. If a change is made and the input current decreases, then the efficiency has improved. If there is no change in input current, then there is no change in efficiency. Undervoltage Lockout The LTC3850 has two functions that help protect the controller in case of undervoltage conditions. A precision UVLO comparator constantly monitors the INTVCC voltage to ensure that an adequate gate-drive voltage is present. It locks out the switching action when INTVCC is below 3V. To prevent oscillation when there is a disturbance on the INTVCC, the UVLO comparator has 500mV of precision hysteresis. Another way to detect an undervoltage condition is to monitor the VIN supply. Because the RUN pins have a precision turn-on reference of 1.2V, one can use a resistor divider to VIN to turn on the IC when VIN is high enough. An extra 4.5μA of current flows out of the RUN pin once the RUN pin voltage passes 1.2V. One can program the hysteresis of the run comparator by adjusting the values of the resistive divider. For accurate VIN undervoltage detection, VIN needs to be higher than 4V. CIN and COUT Selection The selection of CIN is simplified by the 2-phase architecture and its impact on the worst-case RMS current drawn through the input network (battery/fuse/capacitor). It can be shown that the worst-case capacitor RMS current occurs when only one controller is operating. The controller with the highest (VOUT)(IOUT) product needs to be used in the formula below to determine the maximum RMS capacitor current requirement. Increasing the output current drawn from the other controller will actually decrease the input RMS ripple current from its maximum value. The out-ofphase technique typically reduces the input capacitor’s RMS ripple current by a factor of 30% to 70% when compared to a single phase power supply solution. In continuous mode, the source current of the top MOSFET is a square wave of duty cycle (VOUT)/(VIN). To prevent large voltage transients, a low ESR capacitor sized for the maximum RMS current of one channel must be used. The maximum RMS capacitor current is given by: 1/2 I CIN Required IRMS MAX ( VOUT ) ( VIN – VOUT ) VIN This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturers’ ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than required. Several capacitors may be paralleled to meet size or height requirements in the design. Due to the high operating frequency of the LTC3850, ceramic capacitors can also be used for CIN. Always consult the manufacturer if there is any question. The benefit of the LTC3850 2-phase operation can be calculated by using the equation above for the higher power controller and then calculating the loss that would have resulted if both controller channels switched on at the same time. The total RMS power lost is lower when both controllers are operating due to the reduced overlap of current pulses required through the input capacitor’s ESR. This is why the input capacitor’s requirement calculated above for the worst-case controller is adequate for the dual controller design. Also, the input protection fuse resistance, battery resistance, and PC board trace resistance losses are also reduced due to the reduced peak currents in a 2-phase system. The overall benefit of a multiphase design will only be fully realized when the source impedance of the power supply/battery is included in the efficiency testing. The sources of the top MOSFETs should be placed within 1cm of each other and share a common CIN(s). Separating the sources and CIN may produce undesirable voltage and current resonances at VIN. A small (0.1μF to 1μF) bypass capacitor between the chip VIN pin and ground, placed close to the LTC3850, is also 38501fb 21 LTC3850/LTC3850-1 APPLICATIONS INFORMATION suggested. A 2.2Ω – 10Ω resistor placed between CIN (C1) and the VIN pin provides further isolation between the two channels. The selection of COUT is driven by the effective series resistance (ESR). Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering. The output ripple (ΔVOUT) is approximated by: VOUT IRIPPLE ESR + 1 8fCOUT soft-start or tracking up. Under short-circuit conditions with very low duty cycles, the LTC3850 will begin cycle skipping in order to limit the short-circuit current. In this situation the bottom MOSFET will be dissipating most of the power but less than in normal operation. The shortcircuit ripple current is determined by the minimum ontime tON(MIN) of the LTC3850 (≈ 90ns), the input voltage and inductor value: IL(SC) = tON(MIN) • VIN L where f is the operating frequency, COUT is the output capacitance and IRIPPLE is the ripple current in the inductor. The output ripple is highest at maximum input voltage since IRIPPLE increases with input voltage. Setting Output Voltage The LTC3850 output voltages are each set by an external feedback resistive divider carefully placed across the output, as shown in Figure 9. The regulated output voltage is determined by: R VOUT = 0.8V • 1+ B RA To improve the frequency response, a feed-forward capacitor, CFF , may be used. Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. VOUT The resulting short-circuit current is: ISC = 1/3 VSENSE(MAX) RSENSE – 1 I 2 L(SC) Phase-Locked Loop and Frequency Synchronization The LTC3850 has a phase-locked loop (PLL) comprised of an internal voltage-controlled oscillator (VCO) and a phase detector. This allows the turn-on of the top MOSFET of controller 1 to be locked to the rising edge of an external clock signal applied to the MODE/PLLIN pin. The turn-on of controller 2’s top MOSFET is thus 180 degrees outof-phase with the external clock. The phase detector is an edge sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. The output of the phase detector is a pair of complementary current sources that charge or discharge the external filter network connected to the FREQ/PLLFLTR pin. The relationship between the voltage on the FREQ/PLLFLTR pin and operating frequency is shown in Figure 10 and specified in the Electrical Characteristics table. Note that the LTC3850 can only be synchronized to an external clock whose frequency is within range of the LTC3850’s internal VCO. This is guaranteed to be between 250kHz and 780kHz. A simplified block diagram is shown in Figure 11. If no clock is applied to MODE/PLLIN pin, the FREQ/ PLLFLTR pin will be high impedance. If the external clock frequency is greater than the internal oscillator’s frequency, fOSC , then current is sourced con38501fb 1/2 LTC3850 VFB RB CFF RA 38501 F09 Figure 9. Setting Output Voltage Fault Conditions: Current Limit and Current Foldback The LTC3850 includes current foldback to help limit load current when the output is shorted to ground. If the output falls below 50% of its nominal output level, then the maximum sense voltage is progressively lowered from its maximum programmed value to one-third of the maximum value. Foldback current limiting is disabled during the 22 LTC3850/LTC3850-1 APPLICATIONS INFORMATION 900 800 700 FREQUENCY (kHz) 600 500 400 300 200 100 0 0 0.5 1 1.5 2 FREQ/PLLFLTR PIN VOLTAGE (V) 2.5 38501 F10 Typically, the external clock (on MODE/PLLIN pin) input high threshold is 1.6V, while the input low threshold is 1V. Minimum On-Time Considerations Minimum on-time tON(MIN) is the smallest time duration that the LTC3850 is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that V tON(MIN) < OUT VIN(f) If the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles. The output voltage will continue to be regulated, but the ripple voltage and current will increase. The minimum on-time for the LTC3850 is approximately 90ns, with reasonably good PCB layout, minimum 30% inductor current ripple and at least 10mV – 15mV ripple on the current sense signal. The minimum on-time can be affected by PCB switching noise in the voltage and current loop. As the peak sense voltage decreases the minimum on-time gradually increases to 130ns. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple. Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: %Efficiency = 100% – (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. 38501fb Figure 10. Relationship Between Oscillator Frequency and Voltage at the FREQ/PLLFLTR Pin 2.4V RLP CLP MODE/ PLLIN EXTERNAL OSCILLATOR FREQ/ PLLFLTR DIGITAL PHASE/ FREQUENCY DETECTOR VCO 38501 F11 Figure 11. Phase-Locked Loop Block Diagram tinuously from the phase detector output, pulling up the FREQ/PLLFLTR pin. When the external clock frequency is less than fOSC , current is sunk continuously, pulling down the FREQ/PLLFLTR pin. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage on the FREQ/PLLFLTR pin is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the filter capacitor CLP holds the voltage. The loop filter components, CLP and RLP, smooth out the current pulses from the phase detector and provide a stable input to the voltage-controlled oscillator. The filter components CLP and RLP determine how fast the loop acquires lock. Typically RLP = 10k and CLP is 2200pF to 0.01μF . 23 LTC3850/LTC3850-1 APPLICATIONS INFORMATION Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3850 circuits: 1) IC VIN current, 2) INTVCC regulator current, 3) I2R losses, 4) Topside MOSFET transition losses. 1. The VIN current is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents. VIN current typically results in a small (1μF) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT , causing a rapid drop in VOUT . No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 • CLOAD . Thus a 10μF capacitor would require a 250μs rise time, limiting the charging current to about 200mA. PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the IC. These items are also illustrated graphically in the layout diagram of Figure 12. Figure 13 illustrates the current waveforms present in the various branches of the 2-phase synchronous regulators operating in the continuous mode. Check the following in your layout: 1. Are the top N-channel MOSFETs M1 and M3 located within 1 cm of each other with a common drain connection at CIN? Do not attempt to split the input decoupling for the two channels as it can cause a large resonant loop. 2. Are the signal and power grounds kept separate? The combined IC signal ground pin and the ground return of CINTVCC must return to the combined COUT (–) terminals. The VFB and ITH traces should be as short as possible. The path formed by the top N-channel MOSFET, Schottky diode and the CIN capacitor should have short leads and PC trace lengths. The output capacitor (–) terminals should be connected as close as possible to the (–) terminals of the input capacitor by placing the capacitors next to each other and away from the Schottky loop described above. 3. Do the LTC3850 VFB pins’ resistive dividers connect to the (+) terminals of COUT? The resistive divider must be connected between the (+) terminal of COUT and signal ground. The feedback resistor connections should not be along the high current input feeds from the input capacitor(s). 4. Are the SENSE+ and SENSE– leads routed together with minimum PC trace spacing? The filter capacitor between SENSE+ and SENSE– should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the sense resistor or inductor, whichever is used for current sensing. 38501fb 25 LTC3850/LTC3850-1 APPLICATIONS INFORMATION TK/SS1 ITH1 VFB1 L1 SENSE1+ SENSE1– PLLLPF ILIM fIN MODE/PLLIN VIN RUN1 PGND RUN2 SGND SENSE2– SENSE2+ VFB2 ITH2 TK/SS2 EXTVCC INTVCC BG2 BOOST2 CB2 SW2 TG2 L2 RSENSE VOUT2 CINTVCC CVIN RIN VIN TG1 SW1 CB1 BOOST1 BG1 M1 M2 D1 RSENSE VOUT1 PGOOD RPU2 VPULL-UP PGOOD 1μF CERAMIC COUT1 + GND + CIN + 1μF CERAMIC M3 M4 COUT2 D2 38501 F12 + Figure 12. Recommended Printed Circuit Layout Diagram SW1 L1 RSENSE1 VOUT1 D1 COUT1 RL1 VIN RIN CIN SW2 L2 RSENSE2 VOUT2 BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH. D2 COUT2 RL2 38501 F13 Figure 13. Branch Current Waveforms 38501fb 26 LTC3850/LTC3850-1 APPLICATIONS INFORMATION 5. Is the INTVCC decoupling capacitor connected close to the IC, between the INTVCC and the power ground pins? This capacitor carries the MOSFET drivers current peaks. An additional 1μF ceramic capacitor placed immediately next to the INTVCC and PGND pins can help improve noise performance substantially. 6. Keep the switching nodes (SW1, SW2), top gate nodes (TG1, TG2), and boost nodes (BOOST1, BOOST2) away from sensitive small-signal nodes, especially from the opposite channel’s voltage and current sensing feedback pins. All of these nodes have very large and fast moving signals and therefore should be kept on the “output side” of the LTC3850 and occupy minimum PC trace area. If DCR sensing is used, place the top resistor (Figure 2b, R1) close to the switching node. 7. Use a modified “star ground” technique: a low impedance, large copper area central grounding point on the same side of the PC board as the input and output capacitors with tie-ins for the bottom of the INTVCC decoupling capacitor, the bottom of the voltage feedback resistive divider and the SGND pin of the IC. PC Board Layout Debugging Start with one controller at a time. It is helpful to use a DC-50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold—typically 10% of the maximum designed current level in Burst Mode operation. The duty cycle percentage should be maintained from cycle to cycle in a well-designed, low noise PCB implementation. Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PC layout if regulator bandwidth optimization is not required. Only after each controller is checked for its individual performance should both controllers be turned on at the same time. A particularly difficult region of operation is when one controller channel is nearing its current comparator trip point when the other channel is turning on its top MOSFET. This occurs around 50% duty cycle on either channel due to the phasing of the internal clocks and may cause minor duty cycle jitter. Reduce VIN from its nominal level to verify operation of the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, Schottky and the top MOSFET components to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the SGND pin of the IC. Design Example As a design example for a two channel medium current regulator, assume VIN = 12V(nominal), VIN = 20V(maximum), VOUT1 = 3.3V, VOUT2 = 1.8V, IMAX1,2 = 5A, and f = 500kHz (see Figure 14). The regulated output voltages are determined by: VOUT = 0.8V • 1+ RB RA Using 20k 1% resistors from both VFB nodes to ground, the top feedback resistors are (to the nearest 1% standard value) 63.4k and 25.5k. The frequency is set by biasing the FREQ/PLLFLTR pin to 1.2V (see Figure 10), using a divider from INTVCC. This 38501fb 27 LTC3850/LTC3850-1 APPLICATIONS INFORMATION 2.2Ω 4.7μF M1 L1 3.3μH 0.1μF 1μF 22μF 50V VIN 7V TO 20V D3 VIN PGOOD EXTVCC INTVCC TG1 TG2 BOOST1 SW1 BG1 LTC3850 BOOST2 SW2 BG2 D4 M2 0.1μF L2 2.2μH 4.12k 1% 6.19k 1% 10k, 1% PGND FREQ/PLLFLTR SENSE2+ 0.1μF SENSE2– RUN2 VFB2 ITH2 SGND TK/SS2 0.1μF 3.16k 1% 2200pF 5.49k 1% 100pF 20k 1% 1.5k 1% MODE/PLLIN ILIM SENSE1+ 1.33k 1% 0.1μF SENSE1 RUN1 VFB1 ITH1 1800pF 20k 1% 4.75k 1% 100pF 0.1μF TK/SS1 – 33pF VOUT1 3.3V 5A 33pF VOUT2 1.8V 5A COUT2 100μF X2 38501 F14 63.4k 1% COUT1 100μF X2 25.5k 1% L1, L2: COILTRONICS HCP0703 M1, M2: VISHAY SILICONIX Si4816BDY COUT1, COUT2: TAIYO YUDEN JMK325BJ107MM Figure 14. High Efficiency Dual 500kHz 3.3V/1.8V Step-Down Converter voltage will decrease as VIN approaches 5V, lowering the switching frequency. If a separate 5V supply is connected to EXTVCC, INTVCC will remain at 5V even if VIN decreases. The inductance values are based on a 35% maximum ripple current assumption (1.75A for each channel). The highest value of ripple current occurs at the maximum input voltage: VOUT VOUT L= 1 f • IL(MAX) VIN(MAX) Channel 1 will require 3.2μH, and Channel 2 will require 1.9μH. The next highest standard values are 3.3μH and 2.2μH. At the nominal input voltage (12V), the ripple will be: V VOUT IL(NOM) = OUT 1 f •L VIN(NOM) Channel 1 will have 1.45A (29%) ripple, and Channel 2 will have 1.4A (28%) ripple. The peak inductor current will be the maximum DC value plus one-half the ripple current, or 5.725A for Channel 1 and 5.7A for Channel 2. The minimum on-time occurs on Channel 1 at the maximum VIN, and should not be less than 90ns: VOUT 1.8V tON(MIN) = = = 180ns VIN(MAX) f 20V(500kHz) With ILIM floating, the equivalent RSENSE resistor value can be calculated by using the minimum value for the maximum current sense threshold (40mV). VSENSE(MIN) RSENSE(EQUIV) = = IL(NOM) ILOAD(MAX) + 2 40mV 7m 1.5A 5A + 2 The equivalent RSENSE is the same for Channel 2. 38501fb 28 LTC3850/LTC3850-1 APPLICATIONS INFORMATION The Coiltronics (Cooper) HCP0703-2R2 (20mΩ DCRMAX at 20°C) and HCP0703-3R3 (30mΩ DCRMAX at 20°C) are chosen. At 100°C, the estimated maximum DCR values are 26.4mΩ and 39.6mΩ. The divider ratios are: RD = and RSENSE(EQUIV) DCRMAX at TL(MAX) 7m 39.6m 0.18 = 7m = 0.26; 26.4m The respective values for Channel 2 are R1 = 4.12k, R2 = 1.5k; and PLOSS R1 = 8mW. Burst Mode operation is chosen for high light load efficiency (Figure 15) by floating the MODE/PLLIN pin. Power loss due to the DCR sensing network is slightly higher at light loads than would have been the case with a suitable sense resistor (7mΩ). At heavier loads, DCR sensing provides higher efficiency. The power dissipation on the topside MOSFET can be easily estimated. Choosing a Siliconix Si4816BDY dual MOSFET . results in: RDS(ON) = 0.023Ω/0.016Ω, CMILLER ≅ 100pF At maximum input voltage with T(estimated) = 50°C: PMAIN = 3.3V 2 (5) [1+ (0.005)(50°C – 25°C)] • 20V (0.023 ) + (20V )2 5A (2 )(100pF ) • 2 1 1 + (500kHz ) = 186mW 5 – 2.3 2.3 A short-circuit to ground will result in a folded back current of: (1/ 3) 50mV – 1 90ns(20V) = 2.1A ISC = 0.007 2 3.3 μH with a typical value of RDS(ON) and δ = (0.005/°C)(20) = 0.1. The resulting power dissipated in the bottom MOSFET is: 10 DCR 90 EFFICIENCY (%) 80 70 60 50 40 0.01 EFFICIENCY POWER LOSS 0.1 1 LOAD CURRENT (mA) 10 38501 F15 For each channel, 0.1μF is selected for C1. R1||R2 = L 2.2μH = (DCRMAX at 20°C) • C1 20m • 0.1μF 3.3 μH = 1.1k ; and = 1.1k 30m • 0.1μF For channel 1, the DCRSENSE filter/divider values are: R1||R2 1.1k = 6.19k; RD 0.18 R1 • RD 6.19k • 0.18 R2 = = 1.33k 1 RD 1 0.18 R1 = The power loss in R1 at the maximum input voltage is: PLOSS R1= (VIN(MAX) VOUT ) • VOUT R1 = (20V 3.3V) • 3.3V = 9mW 6.19k 100 PSYNC = POWER LOSS (mW) 7mΩ DCR 20V – 3.3V (2.1A )2 (1.125)(0.016 20V = 66mW ) 1 which is less than under full-load conditions. CIN is chosen for an RMS current rating of at least 2A at temperature assuming only channel 1 or 2 is on. COUT is chosen with an ESR of 0.02Ω for low output ripple. The output ripple in continuous mode will be highest at the maximum input voltage. The output voltage ripple due to ESR is approximately: VORIPPLE = RESR (ΔIL) = 0.02Ω(1.5A) = 30mVP–P 38501fb 0.1 0.01 Figure 15. Design Example Efficiency vs Load 29 LTC3850/LTC3850-1 TYPICAL APPLICATIONS VIN 7V TO 24V 2.2Ω 1μF 4.7μF D3 M1 0.1μF L2 2.2μH TG1 VIN PGOOD INTVCC TG2 BOOST2 SW2 LTC3850 BG2 10k 1% 10Ω 1000pF SENSE1– 15pF VOUT1 3.3V 5A 10Ω RUN1 VFB1 ITH1 20k 1% 1000pF 100pF 10k 1% TK/SS1 0.1μF SGND SENSE2– RUN2 EXTVCC VFB2 ITH2 TK/SS2 0.1μF 3.16k 1% 1000pF 15k 1% 100pF 10Ω D4 M2 0.1μF 22μF 50V BOOST1 SW1 BG1 L2 3.3μH 10Ω 8mΩ 1000pF MODE/PLLIN PGND ILIM FREQ/PLLFLTR SENSE1+ SENSE2+ 8mΩ 10pF VOUT2 5V 5A 63.4k 1% 105k 1% 20k 1% + COUT1 220μF + COUT2 150μF 38501 F16 L1: TDK RLF 7030T-2R2M5R4 L2: TDK ULF10045T-3R3N6R9 COUT1: SANYO 4TPE220MF COUT2: SANYO 6TPE150MI Figure 16. 3.3V/5A, 5V/5A Converter Using Sense Resistors 38501fb 30 VIN 7V TO 14V CIN 180μF 10k C4 0.1μF R27 L1 4.02k 0.68μH CB1 0.1μF SENSE1– SENSE1+ RUN1 FREQ/ MODE/ SW1 TG1 PLLFLTR PLLIN D3 CMDSH-3 TK/SS1 ITH1 VFB1 VFB2 ITH2 TK/SS2 SENSE2– BOOST2 CB2 0.1μF SENSE2+ SGND RUN2 ILIM EXTVCC PGOOD SW2 TG2 C5 0.1μF PGOOD RPG 100k PGND D4 CMDSH-3 BG2 CVCC 4.7μF PGND GND M3 HAT2168H LTC3850 INTVCC CVIN 1μF VIN BG1 BOOST1 M2 RJK0301DPB M1 HAT2168H RVIN 2.2Ω 10μF 2x + CSS 0.1μF 2.10k TYPICAL APPLICATIONS C6 100pF R1 43.2k C10 33pF VOUT1 2.5V/ 15A C7 1000pF R12 7.5k + R2 20k COUT1 330μF 4V 2X C11 1000pF R18 4.99k R3 20k R4 25.5k C15 47pF L2 0.68μH R30 4.02k M4 RJK0301DPB 20k 25.5k L1, L2: VISHAY IHLP5050EZ-01 0.68μH COUT1, COUT2: SANYO 4TPD330M 38501 TA02 Figure 17. 2.5V/15A, 1.8V/15A Converter with DCR Sensing and Coincident Rail Tracking FSW = 350kHz + C12 100pF COUT2 330μF 4V 2X VOUT2 1.8V/ 15A LTC3850/LTC3850-1 31 38501fb TYPICAL APPLICATIONS LTC3850/LTC3850-1 C12 100pF SENSE2– BOOST2 CB2 0.1μF SENSE2+ SGND RUN2 ILIM EXTVCC PGOOD SW2 TG2 C5 1000pF PGOOD R22 100Ω RPG 100k CSS2 0.1μF R4 10k M3 RJK0305DPB L2 0.4μH RSENSE2 0.002Ω M4 RJK0301DPB R20 100Ω 38501 F18 L1, L2: VITEC 59PR9875 COUT1, COUT2: 2R5TPE330M9 Figure 18. 1.5V/15A, 1.2V/15A Core-I/O Converter with Sense Resistor Synchronized at 400kHz + 32 C1 1000pF R9 100Ω C4 1000pF M1 RJK0305DPB L1 0.4μH CB1 0.1μF SENSE1– SENSE1+ RUN1 FREQ/ MODE/ SW1 TG1 PLLFLTR PLLIN D3 CMDSH-3 M2 RJK0301DPB TK/SS1 ITH1 VFB1 VFB2 ITH2 TK/SS2 PGND D4 CMDSH-3 BG2 CVCC 4.7μF PGND GND COUT2 330μF 2.5V 2X VOUT2 1.2V/15A LTC3850 INTVCC CVIN 1μF VIN BG1 BOOST1 RSENSE1 0.002Ω VOUT1 1.5V/15A R5 10k PLLIN 400kHz R10 100Ω C2 0.01μF RVIN 2.2Ω 10μF 2x VIN 7V TO 14V CIN 180μF + CSS1 0.1μF C6 100pF R1 17.8k C7 1000pF + R12 5.9k R2 20k COUT1 330μF 2.5V 2X C11 1000pF R18 5.9k R3 20k 38501fb LTC3850/LTC3850-1 TYPICAL APPLICATIONS 5V ± 0.5V 1Ω 4.7μF M1 L1 0.75μH 0.1μF 4.7μF 6.3V 2x D4 M2 0.1μF L2 0.75μH 1.2k 1% D3 VIN PGOOD EXTVCC INTVCC TG1 BOOST1 SW1 BG1 LTC3850 TG2 BOOST2 SW2 BG2 PGND FREQ/PLLFLTR SENSE2+ 1.2k 1% PLLIN 750kHz MODE/PLLIN ILIM SENSE1+ 2.94k 1% 47pF VOUT1 1.8V 5A 0.047μF SENSE1 RUN1 VFB1 ITH1 2200pF – 0.047μF SENSE2– RUN2 VFB2 ITH2 SGND TK/SS2 0.1μF 1nF 10nF 10k 1% 2200pF 14k 1% 4.99k 1% 100pF VOUT2 1.2V 5A COUT2 100μF X2 38501 F19 25.5k 1% COUT1 100μF X2 20k 1% 14k 1% 100pF 0.1μF TK/SS1 100pF 20k 1% 10k 1% L1, L2: TOKO FDV0630 0.75μH M1, M2: VISHAY SILICONIX Si4816BDY COUT1, COUT2: TAIYO YUDEN JMK325BJ107MM Figure 19. 1.8V/5A, 1.2V/5A Core-I/O Converter with a 5V Input Synchronized at 750kHz VIN1 12V 4.7μF 4.7μF M1 L1 2.2μH 0.1μF 2.2Ω 1μF 13.0k 10k M2 0.1μF L2 0.75μH 1.2k 1% 4.7μF 2x VIN2 3.3V D3 VIN PGOOD EXTVCC INTVCC TG1 TG2 BOOST1 SW1 BG1 LTC3850 BOOST2 SW2 BG2 PGND FREQ/PLLFLTR SENSE2+ D4 3.74k 1% MODE/PLLIN ILIM SENSE1+ 1.40k 1% 0.1μF SENSE1– RUN1 VFB1 ITH1 2200pF 20k 1% 10k 1% 100pF TK/SS1 SGND 10k 1% 0.1μF SENSE2– RUN2 VFB2 ITH2 TK/SS2 0.1μF 3.16k 1% 2200pF 6.04k 1% 4.32k 1% 100pF VOUT2 1.2V 5A COUT2 100μF X2 38501 F20 47pF VOUT1 2.5V 5A 43.2k 1% COUT1 100μF X2 100pF 20k 1% 10k 1% 0.1μF L1: TOKO FDV0630 2.2μH L2: TOKO FDV0630 0.75μH M1, M2: VISHAY SILICONIX Si4816BDY COUT1, COUT2: TAIYO YUDEN JMK325BJ107MM Figure 20. 2.5V/5A, 1.2V/5A Core-I/O Converter with Dual Inputs 38501fb 33 LTC3850/LTC3850-1 PACKAGE DESCRIPTION GN Package 28-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .386 – .393* (9.804 – 9.982) 28 27 26 25 24 23 22 21 20 19 18 17 1615 .045 ± .005 .033 (0.838) REF .254 MIN .150 – .165 .229 – .244 (5.817 – 6.198) .150 – .157** (3.810 – 3.988) .0165 ± .0015 RECOMMENDED SOLDER PAD LAYOUT .0250 BSC 1 .0532 – .0688 (1.35 – 1.75) 23 4 56 7 8 9 10 11 12 13 14 .004 – .0098 (0.102 – 0.249) .015 ± .004 × 45° (0.38 ± 0.10) .0075 – .0098 (0.19 – 0.25) 0° – 8° TYP .016 – .050 (0.406 – 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) 3. DRAWING NOT TO SCALE .0250 .008 – .012 (0.635) (0.203 – 0.305) BSC TYP *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE GN28 (SSOP) 0204 UF Package 28-Lead Plastic QFN (4mm × 4mm) (Reference LTC DWG # 05-08-1721 Rev A) BOTTOM VIEW—EXPOSED PAD 4.00 ± 0.10 (4 SIDES) 0.70 ± 0.05 4.50 ± 0.05 3.10 ± 0.05 2.64 ± 0.05 (4 SIDES) PIN 1 TOP MARK (NOTE 6) 0.75 ± 0.05 R = 0.05 TYP R = 0.115 TYP PIN 1 NOTCH R = 0.20 TYP OR 0.35 × 45° CHAMFER 27 28 0.40 ± 0.05 1 2 2.64 ± 0.10 (4-SIDES) PACKAGE OUTLINE 0.20 ± 0.05 0.40 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED (UF28) QFN 0106 REVA 0.200 REF 0.00 – 0.05 0.20 ± 0.05 0.40 BSC NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 5. EXPOSED PAD SHALL BE SOLDER PLATED 2. DRAWING NOT TO SCALE 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 3. ALL DIMENSIONS ARE IN MILLIMETERS LOCATION ON THE TOP AND BOTTOM OF PACKAGE 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT 38501fb 34 LTC3850/LTC3850-1 PACKAGE DESCRIPTION UFD Package 28-Lead Plastic QFN (4mm × 5mm) (Reference LTC DWG # 05-08-1712 Rev B) 0.70 ± 0.05 4.50 ± 0.05 3.10 ± 0.05 2.50 REF 2.65 ± 0.05 3.65 ± 0.05 PACKAGE OUTLINE 0.25 ± 0.05 0.50 BSC 3.50 REF 4.10 ± 0.05 5.50 ± 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 4.00 ± 0.10 (2 SIDES) 0.75 ± 0.05 R = 0.05 TYP PIN 1 NOTCH R = 0.20 OR 0.35 × 45° CHAMFER 27 28 0.40 ± 0.10 1 2 5.00 ± 0.10 (2 SIDES) 2.50 REF R = 0.115 TYP PIN 1 TOP MARK (NOTE 6) 3.50 REF 3.65 ± 0.10 2.65 ± 0.10 (UFD28) QFN 0506 REV B 0.200 REF 0.00 – 0.05 0.25 ± 0.05 0.50 BSC BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WXXX-X). 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 38501fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 35 LTC3850/LTC3850-1 TYPICAL APPLICATION 2.55k 1nF 0.1μF 220pF 2.2nF 2.74k 20k VFB1 VFB2 ITH2 TK/SS2 SENSE2– LTC3850 VIN INTVCC BG2 PGND CMDSH-3 BOOST2 RJK0305DPB SENSE2+ SGND RUN2 ILIM EXTVCC PGOOD SW2 TG2 0.1μF PGOOD 20k 100k 0.1μF RJK0301DPB 2.21k L2 0.56μH 4.7μF 1μF VOUT 1.1V/30A 100μF 2x TK/SS1 ITH1 BOOST1 BG1 2.2Ω 7.5k 20k RUN 0.1μF 0.1μF CMDSH-3 10k RJK0305DPB 2.21k L1 0.56μH 10μF 2x VIN 7V TO 14V 180μF + SENSE1– SENSE1+ RUN1 FREQ MODE SW1 TG1 RJK0301DPB + COUT1 330μF 2.5V 4x RUN L1, L2: VISHAY IHLP4040DZ-01 0.56μH COUT: SANYO 2R5TPE330M9 FOR SINGLE OUTPUT, DUAL PHASE OPERATION, TIE THE FOLLOWING PINS TOGETHER: TK/SS1 TO TK/SS2 VFB1 TO VFB1 RUN1 TO RUN2 ITH1 TO ITH2 38501 TA04 Figure 21. 1.1V/30A Dual Phase Core Converter, FSW = 400kHz RELATED PARTS PART NUMBER DESCRIPTION LTC1625/ LTC1775 LTC1735 LTC1778 LTC3727A-1 LTC3728 LTC3729 LTC3731 LTC3773 LTC3810 LTC3826 LTC3828 LTC3834/ LTC3834-1 LT3845 No RSENSE™ Current Mode Synchronous Step-Down Controllers High Efficiency Synchronous Step-Down Switching Regulator No RSENSE Wide Input Range Synchronous Step-Down Controller Dual, 2-Phase Synchronous Controller 2-Phase 550kHz, Dual Synchronous Step-Down Controller 20A to 200A PolyPhase® Synchronous Controllers 3-Phase, Single Output From 250kHz to 600kHz Synchronous Step-Down Controller Triple Output DC/DC Synchronous Controller 100V Current Mode Synchronous Step-Down Switching Controller Low IQ, Dual, 2-Phase Synchronous Step-Down Controller Dual, 2-Phase Synchronous Step-Down Controller with Tracking Low IQ, Synchronous Step-Down Controller Low IQ, High Voltage Single Output Synchronous Step-Down DC/DC Controller COMMENTS 97% Efficiency, No Sense Resistor, 16-Pin SSOP Programmable Fixed Frequency from 200kHz to 550kHz Up to 97% Efficiency, 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ (0.9)(VIN), IOUT Up to 20A Very Low Dropout; VOUT ≤ 14V, 4V ≤ VIN ≤ 36V QFN and SSOP Packages, High Frequency for Smaller L and C Expandable from 2-Phase to 12-Phase, Uses All Surface Mount Components 0.6V ≤ VOUT ≤ 6V, 4.5V ≤ VIN ≤ 32V, IOUT ≤ 60A, Integrated MOSFET Drivers 3-Phase Step-Down DC/DC Controller, 3.3V ≤ VIN ≤ 36V, Fixed Frequency 160kHz to 700kHz 0.8V ≤ VOUT ≤ 0.93VIN, 6.2V ≤ VIN ≤ 100V, No RSENSE 30μA IQ, 0.8V ≤ VOUT ≤ 10V, 4V ≤ VIN ≤ 36V Up to Six Phases, 0.8V ≤ VOUT ≤ 7V, 4.5V ≤ VIN ≤ 28V 30μA IQ, 0.8V ≤ VOUT ≤ 10V, 4V ≤ VIN ≤ 36V 1.23V ≤ VOUT ≤ 36V, 4V ≤ VIN ≤ 60V, 120μA IQ 38501fb PolyPhase is a registered trademark of Linear Technology Corporation. No RSENSE is a trademark of Linear Technology Corporation. 36 Linear Technology Corporation (408) 432-1900 ● FAX: (408) 434-0507 ● LT 0508 REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 www.linear.com © LINEAR TECHNOLOGY CORPORATION 2007